After 52358dd63e ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MediaTek MT7988 SoC comes with an single built-in Ethernet PHY for
2500Base-T/1000Base-T/100Base-TX/10Base-T link partners in addition to
the built-in 1GE switch. The built-in PHY only supports full duplex.
Add muxes allowing to select GMAC2->2.5G PHY path and add basic support
for XGMAC as the built-in 2.5G PHY is internally connected via XGMII.
The XGMAC features will also be used by 5GBase-R, 10GBase-R and USXGMII
SerDes modes which are going to be added once support for standalone PCS
drivers is in place.
In order to make use of the built-in 2.5G PHY the appropriate PHY driver
as well as (proprietary) PHY firmware has to be present as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/9072cefbff6db969720672ec98ed5cef65e8218c.1745715380.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This user of SHA-256 does not support any other algorithm, so the
crypto_shash abstraction provides no value. Just use the SHA-256
library API instead, which is much simpler and easier to use.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://patch.msgid.link/20250428191606.856198-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8211F supports multiple WOL modes. This patch adds support for
magic packets.
The PHY notifies the system via the INTB/PMEB pin when a WOL event
occurs.
Signed-off-by: Daniel Braunwarth <daniel.braunwarth@kuka.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429-realtek_wol-v2-1-8f84def1ef2c@kuka.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure the following prerequisites before executing the test:
1. 'socat' is installed on the remote host.
2. Python version supports socket.SO_INCOMING_CPU (available since v3.11).
Skip the test if either prerequisite is not met.
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250430054801.750646-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MSM DisplayPort driver implements several HDMI codec functions
in the driver, e.g. it manually manages HDMI codec device registration,
returning ELD and plugged_cb support. In order to reduce code
duplication reuse drm_hdmi_audio_* helpers and drm_bridge_connector
integration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/649728/
Link: https://lore.kernel.org/r/20250423-dp-hdmi-audio-v7-1-8407a23e55b2@oss.qualcomm.com
The SDM630 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask, replacing PINGPONG_SDM845_MASK with
BIT(DPU_PINGPONG_DITHER).
Fixes: 7204df5e7e ("drm/msm/dpu: add support for SDM660 and SDM630 platforms")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640308/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-5-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Neither DPU driver nor vendor SDE driver do not use TE2 definitions
(and, in case of SDE driver, never did). Semantics of the TE2 feature
bit and .te2 sblk are not completely clear. Drop these bits from the
catalog with the possibility of reintroducing them later if we need to
support ppsplit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640305/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-4-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8953 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: 7a6109ce1c ("drm/msm/dpu: Add support for MSM8953")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640303/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-3-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8917 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: 62af6e1cb5 ("drm/msm/dpu: Add support for MSM8917")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640301/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-2-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The MSM8937 platform doesn't have DSC blocks nor does have it DSC
registers in the PINGPONG block. Drop the DPU_PINGPONG_DSC feature bit
from the PINGPONG's feature mask and, as it is the only remaining bit,
drop the .features assignment completely.
Fixes: c079680bb0 ("drm/msm/dpu: Add support for MSM8937")
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/640299/
Link: https://lore.kernel.org/r/20250301-dpu-fix-catalog-v2-1-498271be8b50@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Describe the Mobile Display SubSystem (MDSS) device present on the
Qualcomm SAR2130P platform. It looks pretty close to SM8550 on the
system level. SAR2130P features two DSI hosts and single DisplayPort
controller.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/649265/
Link: https://lore.kernel.org/r/20250418-sar2130p-display-v5-5-442c905cb3a4@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Allwinner A523 SoC variant (A527/T527) contains an "EMAC0" Ethernet
MAC compatible to the A64 version.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Link: https://patch.msgid.link/20250430-01-sun55i-emac0-v3-2-6fc000bbccbd@gentoo.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-29 (igb, igc, ixgbe, idpf)
For igb:
Kurt Kanzenbach adds linking of IRQs and queues to NAPI instances and
adds persistent NAPI config. Lastly, he removes undesired IRQs that
occur while busy polling.
For igc:
Kurt Kanzenbach switches the Tx mode for MQPRIO offload to harmonize the
current implementation with TAPRIO.
For ixgbe:
Jedrzej adds separate ethtool ops for E610 devices to account for device
differences.
Slawomir adds devlink region support for E610 devices.
For idpf:
Mateusz assigns and utilizes the ptype field out of libeth_rqe_info.
Michal removes unreachable code.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
idpf: remove unreachable code from setting mailbox
idpf: assign extracted ptype to struct libeth_rqe_info field
ixgbe: devlink: add devlink region support for E610
ixgbe: add E610 .set_phys_id() callback implementation
ixgbe: apply different rules for setting FC on E610
ixgbe: add support for ACPI WOL for E610
ixgbe: create E610 specific ethtool_ops structure
igc: Change Tx mode for MQPRIO offloading
igc: Limit netdev_tc calls to MQPRIO
igb: Get rid of spurious interrupts
igb: Add support for persistent NAPI config
igb: Link queues to NAPI instances
igb: Link IRQs to NAPI instances
====================
Link: https://patch.msgid.link/20250429234651.3982025-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing
direct loader exec"), the brk was moved out of the mmap region when
loading static PIE binaries (ET_DYN without INTERP). The common case
for these binaries was testing new ELF loaders, so the brk needed to
be away from mmap to avoid colliding with stack, future mmaps (of the
loader-loaded binary), etc. But this was only done when ASLR was enabled,
in an attempt to minimize changes to memory layouts.
After adding support to respect alignment requirements for static PIE
binaries in commit 3545deff0e ("binfmt_elf: Honor PT_LOAD alignment
for static PIE"), it became possible to have a large gap after the
final PT_LOAD segment and the top of the mmap region. This means that
future mmap allocations might go after the last PT_LOAD segment (where
brk might be if ASLR was disabled) instead of before them (where they
traditionally ended up).
On arm64, running with ASLR disabled, Ubuntu 22.04's "ldconfig" binary,
a static PIE, has alignment requirements that leaves a gap large enough
after the last PT_LOAD segment to fit the vdso and vvar, but still leave
enough space for the brk (which immediately follows the last PT_LOAD
segment) to be allocated by the binary.
fffff7f20000-fffff7fde000 r-xp 00000000 fe:02 8110426 /sbin/ldconfig.real
fffff7fee000-fffff7ff5000 rw-p 000be000 fe:02 8110426 /sbin/ldconfig.real
fffff7ff5000-fffff7ffa000 rw-p 00000000 00:00 0
***[brk will go here at fffff7ffa000]***
fffff7ffc000-fffff7ffe000 r--p 00000000 00:00 0 [vvar]
fffff7ffe000-fffff8000000 r-xp 00000000 00:00 0 [vdso]
fffffffdf000-1000000000000 rw-p 00000000 00:00 0 [stack]
After commit 0b3bc3354e ("arm64: vdso: Switch to generic storage
implementation"), the arm64 vvar grew slightly, and suddenly the brk
collided with the allocation.
fffff7f20000-fffff7fde000 r-xp 00000000 fe:02 8110426 /sbin/ldconfig.real
fffff7fee000-fffff7ff5000 rw-p 000be000 fe:02 8110426 /sbin/ldconfig.real
fffff7ff5000-fffff7ffa000 rw-p 00000000 00:00 0
***[oops, no room any more, vvar is at fffff7ffa000!]***
fffff7ffa000-fffff7ffe000 r--p 00000000 00:00 0 [vvar]
fffff7ffe000-fffff8000000 r-xp 00000000 00:00 0 [vdso]
fffffffdf000-1000000000000 rw-p 00000000 00:00 0 [stack]
The solution is to unconditionally move the brk out of the mmap region
for static PIE binaries. Whether ASLR is enabled or not does not change if
there may be future mmap allocation collisions with a growing brk region.
Update memory layout comments (with kernel-doc headings), consolidate
the setting of mm->brk to later (it isn't needed early), move static PIE
brk out of mmap unconditionally, and make sure brk(2) knows to base brk
position off of mm->start_brk not mm->end_data no matter what the cause of
moving it is (via current->brk_randomized).
For the CONFIG_COMPAT_BRK case, though, leave the logic unchanged, as we
can never safely move the brk. These systems, however, are not using
specially aligned static PIE binaries.
Reported-by: Ryan Roberts <ryan.roberts@arm.com>
Closes: https://lore.kernel.org/lkml/f93db308-4a0e-4806-9faf-98f890f5a5e6@arm.com/
Fixes: bbdc6076d2 ("binfmt_elf: move brk out of mmap when doing direct loader exec")
Link: https://lore.kernel.org/r/20250425224502.work.520-kees@kernel.org
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Tested-by: Ryan Roberts <ryan.roberts@arm.com>
Signed-off-by: Kees Cook <kees@kernel.org>
The previous patch that added bounds check for create lease context
introduced a memory leak. When the bounds check fails, the function
returns NULL without freeing the previously allocated lease_ctx_info
structure.
This patch fixes the issue by adding kfree(lreq) before returning NULL
in both boundary check cases.
Fixes: bab703ed84 ("ksmbd: add bounds check for create lease context")
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Client can send empty newname string to ksmbd server.
It will cause a kernel oops from d_alloc.
This patch return the error when attempting to rename
a file or directory with an empty new name string.
Cc: stable@vger.kernel.org
Reported-by: Norbert Szetei <norbert@doyensec.com>
Tested-by: Norbert Szetei <norbert@doyensec.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Introduce the zoned_loop.rst documentation file under
admin-guide/blockdev to document the zoned loop block device driver.
An overview of the driver is provided and its usage to create and delete
zoned devices described.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250407075222.170336-3-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The zoned loop block device driver allows a user to create emulated
zoned block devices using one regular file per zone as backing storage.
Compared to null_blk or scsi_debug, it has the advantage of allowing
emulating large zoned devices without requiring the same amount of
memory as the capacity of the emulated device. Furthermore, zoned
devices emulated with this driver can be re-started after a host reboot
without any loss of the state of the device zones, which is something
that null_blk and scsi_debug do not support.
This initial implementation is simple and does not support zone resource
limits. That is, a zoned loop block device limits for the maximum number
of open zones and maximum number of active zones is always 0.
This driver can be either compiled in-kernel or as a module, named
"zloop". Compilation of this driver depends on the block layer support
for zoned block device (CONFIG_BLK_DEV_ZONED must be set).
Using the zloop driver to create and delete zoned block devices is
done by writing commands to the zoned loop control character device file
(/dev/zloop-control). Creating a device is done with:
$ echo "add [options]" > /dev/zloop-control
The options available for the "add" operation cat be listed by reading
the zloop-control device file:
$ cat /dev/zloop-control
add id=%d,capacity_mb=%u,zone_size_mb=%u,zone_capacity_mb=%u,conv_zones=%u,base_dir=%s,nr_queues=%u,queue_depth=%u
remove id=%d
The options available allow controlling the zoned device total
capacity, zone size, zone capactity of sequential zones, total number
of conventional zones, base directory for the zones backing file, number
of I/O queues and the maximum queue depth of I/O queues.
Deleting a device is done using the "remove" command:
$ echo "remove id=0" > /dev/zloop-control
This implementation passes various tests using zonefs and fio (t/zbd
tests) and provides a state machine for zone conditions that is
compliant with the T10 ZBC and NVMe ZNS specifications.
Co-developed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20250407075222.170336-2-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is easy to skip or ignore the fact that the default SSPP feature
masks for SDM845+ don't include the SmartDMA bit (both during
development and during the review stage). Rename SSPP feature masks to
make it more explicit that using non-SmartDMA masks should not be an
exception rather than the rule.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/650425/
Link: https://lore.kernel.org/r/20250425-dpu-rework-vig-masks-v2-5-c71900687d08@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Since SmartDMA planes provide two rectangles, it is possible to use them
to drive two different DRM planes, first plane getting the rect_0,
another one using rect_1 of the same SSPP. The sharing algorithm is
pretty simple, it requires that each of the planes can be driven by the
single rectangle and only consecutive planes are considered.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/650441/
Link: https://lore.kernel.org/r/20250426-dpu-share-sspp-v7-1-6f4c719e373c@oss.qualcomm.com
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
LVDS support in MDP4 driver makes use of drm_connector directly. However
LCDC encoder and LVDS connector are wrappers around drm_panel. Switch
them to use drm_panel_bridge/drm_bridge_connector. This allows using
standard interface for the drm_panel and also inserting additional
bridges between encoder and panel.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/650290/
Link: https://lore.kernel.org/r/20250425-fd-mdp4-lvds-v4-6-6b212160b44c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Instead of using .parent_names, use .parent_data, which binds parent
clocks by using relative names specified in DT in addition to using global
system clock names.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/650284/
Link: https://lore.kernel.org/r/20250425-fd-mdp4-lvds-v4-4-6b212160b44c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The LVDS/LCDC controller uses pixel clock coming from the multimedia
controller (mmcc) rather than using the PLL directly. Stop using LVDS
PLL directly and register it as a clock provider. Use lcdc_clk as a
pixel clock for the LCDC.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/650280/
Link: https://lore.kernel.org/r/20250425-fd-mdp4-lvds-v4-3-6b212160b44c@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>