New register has been introduced with PTL in the vendor specific SHIM
registers, outside of the IPs itself for microphone privacy status handling.
Via the PVCCS register the current microphone privacy status can be checked
and the interrupt generation on status change can be enabled/disabled.
The status change interrupt is routed to the owner of the interface
(DSP/host).
The PVCCS is provided for each sublink under the IP to make it possible to
control the interrupt generation per sublink.
On status change the MDSTSCHG bit needs to be cleared for all sublink of
the interface to be able to detect future changes in privacy.
The status bit (MDSTS) is volatile in all PVCCS register, it reflects the
current state of the GPIO signal.
Microphone privacy is a hardware feature (if enabled and configured that
way), the host has only passive, monitoring role.
The added functions are generic to be future proof if the mic privacy
support is extended beyond Soundwire and DMIC links.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACE3 (Panther Lake) introduced support for microphone privacy feature which
can - in hardware - mute incoming audio data based on a state of a physical
switch.
The change in the privacy state is delivered through interface IP blocks
and can only be handled by the link owner.
In Intel platforms Soundwire is for example host owned, so the interrupt
can only be handled by the host.
Since the input stream is going to be muted by hardware, the host needs to
send a message to firmware about the change in privacy so it can execute a
fade out/in to enhance user experience.
The support for microphone privacy can be queried from the HW_CONFIG data
under the INTEL_MIC_PRIVACY_CAP tuple. This is Intel specific data, the
core will pass it to platform code if the intel_configure_mic_privacy()
callback is provided.
Platform code can call sof_ipc4_mic_privacy_state_change() to send the IPC
message to the firmware on state change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Create a minimal placeholder to make it possible to add code to handle
the new features of Panther Lake compared to MTL/LNL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to export individual dsp_ops functions anymore as the
callbacks are filled now by sof_mtl_set_ops()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LunarLake is a next generation in ACE architecture and most of the dsp_ops
are the same as it is in previous generation.
Use the sof_mtl_set_ops() to get the ops used for mtl and update the ones
that needs different functions for LNL.
Update pci-ptl at the same time to use the LNL dsp_ops as before.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the sof_mtl_ops and sof_mtl_ops_init() to pci-mtl.c as local static
and add a 'generic' sof_mtl_set_ops() function as replacement exported
function to fill the dsp_ops structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new mount option "nat_bits" to control nat_bits feature,
by default nat_bits feature is disabled.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Apparently, ASUS's own firmware also
describes them incorrectly. Correct them to what is seen on the chassis.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: b116239094 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC3200")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250304-for-broadcom-fix-rt-ac3200-switch-ports-v1-1-7e249a19a13e@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
After using the device for a while, Tom reports that he initially described
the switch port labels incorrectly. Correct them.
Reported-by: Tom Brautaset <tbrautaset@gmail.com>
Fixes: 961dedc6b4 ("ARM: dts: BCM5301X: Add DT for ASUS RT-AC5300")
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://lore.kernel.org/r/20250303-for-broadcom-fix-rt-ac5300-switch-ports-v1-1-e058856ef4d3@arinc9.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Device nodes in the examples are supposed to be enabled, so the schema
will be validated against them. Keeping them disabled hides potential
errors.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250307081327.35153-2-krzysztof.kozlowski@linaro.org
The example DTS uses 'num-ib-windows' and 'num-ob-windows' properties
but these are not defined in the binding. Binding also does not
reference snps,dw-pcie-common.yaml, probably because it is quite
different even though the device is based on Synopsys controller.
The properties are actually deprecated, so simply drop them from the
example.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250307081327.35153-1-krzysztof.kozlowski@linaro.org
Remove the superfluous function dw_pcie_ep_find_ext_capability(),
as it is virtually identical to dw_pcie_find_ext_capability().
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250221202646.395252-3-cassel@kernel.org
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Fix a kernel oops found while testing the stm32_pcie Endpoint driver
with handling of PERST# deassertion:
During EP initialization, pci_epf_test_alloc_space() allocates all BARs,
which are further freed if epc_set_bar() fails (for instance, due to no
free inbound window).
However, when pci_epc_set_bar() fails, the error path:
pci_epc_set_bar() ->
pci_epf_free_space()
does not clear the previous assignment to epf_test->reg[bar].
Then, if the host reboots, the PERST# deassertion restarts the BAR
allocation sequence with the same allocation failure (no free inbound
window), creating a double free situation since epf_test->reg[bar] was
deallocated and is still non-NULL.
Thus, make sure that pci_epf_alloc_space() and pci_epf_free_space()
invocations are symmetric, and as such, set epf_test->reg[bar] to NULL
when memory is freed.
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
Link: https://lore.kernel.org/r/20250124123043.96112-1-christian.bruel@foss.st.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The static function devm_pci_epc_match() is only invoked within the
devm_pci_epc_destroy(). However, since it was initially introduced,
this new API has had no callers.
Thus, remove both the unused API and the static function.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250217-remove_api-v2-1-b169c9117045@quicinc.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "11.4.4.29 USP_PCIE_RESBAR Registers Summary" in the
Technical Reference Manual (TRM) for RK3588, we can see that none of the
BARs are Fixed BARs, but actually Resizable BARs.
I couldn't find any reference in the TRM for RK3568, but looking at the
downstream PCIe endpoint driver, both RK3568 and RK3588 are treated as
the same, so the BARs on RK3568 must also be Resizable BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-16-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The support for a specific iATU alignment was added in
commit 2a9a801620 ("PCI: endpoint: Add support to specify alignment for
buffers allocated to BARs").
This commit specifically mentions both that the alignment by each DWC
based EP driver should match CX_ATU_MIN_REGION_SIZE, and that AM65x
specifically has a 64 KB alignment.
This also matches the CX_ATU_MIN_REGION_SIZE value specified in the
section "12.2.2.4.7 PCIe Subsystem Address Translation" of the Technical
Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
This higher value, 1 MB, was obviously an ugly hack used to be able to
handle Resizable BARs which have a minimum size of 1 MB.
Now when we actually have support for Resizable BARs, let's configure the
iATU alignment requirement to the actual requirement.
(BARs described as Resizable will still get aligned to 1 MB.)
Cc: stable+noautosel@kernel.org # Depends on PCI endpoint Resizable BARs series
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-15-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Looking at section "12.2.2.4.15 PCIe Subsystem BAR Configuration" in the
following Technical Reference Manual (TRM) for AM65x:
https://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
We can see that BAR2 and BAR5 are not Fixed BARs, but actually Resizable
BARs.
Now when we actually have support for Resizable BARs, let's configure
these BARs as such.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-14-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The DWC databook specifies three different BARn_SIZING_SCHEME_N as:
- Fixed Mask (0)
- Programmable Mask (1)
- Resizable BAR (2)
Each of these sizing schemes have different instructions for how to
initialize the BAR.
The DWC driver currently does not support resizable BARs.
Instead, in order to somewhat support resizable BARs, the DWC EP driver
currently has an ugly hack that force sets a resizable BAR to 1 MB, if
such a BAR is detected.
Additionally, this hack only works if the DWC glue driver also has lied
in their EPC features, and claimed that the resizable BAR is a 1 MB fixed
size BAR.
This is unintuitive (as you somehow need to know that you need to lie in
your EPC features), but other than that it is overly restrictive, since a
resizable BAR is capable of supporting sizes different than 1 MB.
Add proper support for resizable BARs in the DWC EP driver.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
This means that an EPC driver does not need to lie in EPC features, and an
EPF driver will be able to set an arbitrary size (not be forced to a 1 MB
size), just like BAR_PROGRAMMABLE.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-13-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Move dw_pcie_ep_find_ext_capability() so that it is located next to
dw_pcie_ep_find_capability().
Additionally, a follow-up commit requires this to be defined earlier
in order to avoid a forward declaration.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250131182949.465530-12-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add a helper function to convert a size to the representation used by the
Resizable BAR Capability Register.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-11-cassel@kernel.org
[mani: squashed the change that added PCIe spec reference to comments
from https://lore.kernel.org/linux-pci/20250219171454.2903059-2-cassel@kernel.org]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
A resizable BAR is different from a normal BAR in a few ways:
- The minimum size of a resizable BAR is 1 MB.
- Each BAR that is resizable has a Capability and Control register in
the Resizable BAR Capability structure.
These registers contain the supported sizes and the currently selected
size of a resizable BAR.
The supported sizes is a bitmap of the supported sizes. The selected size
is a single value that is equal to one of the supported sizes.
A resizable BAR thus has to be configured differently than a
BAR_PROGRAMMABLE BAR, which usually sets the BAR size/mask in a vendor
specific way.
The PCI endpoint framework currently does not support resizable BARs.
Add a BAR type BAR_RESIZABLE, so that an EPC driver can support resizable
BARs properly.
Note that the pci_epc_set_bar() API takes a struct pci_epf_bar which tells
the EPC driver how it wants to configure the BAR.
struct pci_epf_bar only has a single size struct member.
This means that an EPC driver will only be able to set a single supported
size. This is perfectly fine, as we do not need the complexity of allowing
a host to change the size of the BAR. If someone ever wants to support
resizing a resizable BAR, the pci_epc_set_bar() API can be extended in the
future.
With these changes, we allow an EPF driver to configure the size of
Resizable BARs, rather than forcing them to a 1 MB size.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250131182949.465530-10-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The struct pci_epf_test_reg is the actual data in pci-epf-test's test_reg
BAR (usually BAR0), which the host uses to send commands (etc.), and which
pci-epf-test uses to send back status codes.
pci-epf-test currently reads and writes this data without any endianness
conversion functions, which means that pci-epf-test is completely broken
on big-endian endpoint systems.
PCI devices are inherently little-endian, and the data stored in the PCI
BARs should be in little-endian.
Use endianness conversion functions when reading and writing data to
struct pci_epf_test_reg so that pci-epf-test will behave correctly on
big-endian endpoint systems.
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20250127161242.104651-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
There are two variables that indicate the interrupt type to be used
in the next test execution, global "irq_type" and "test->irq_type".
The former is referenced from pci_endpoint_test_get_irq() to preserve
the current type for ioctl(PCITEST_GET_IRQTYPE).
In the pci_endpoint_test_request_irq(), since this global variable
is referenced when an error occurs, the unintended error message is
displayed.
For example, after running "pcitest -i 2", the following message
shows "MSI 3" even if the current IRQ type becomes "MSI-X":
pci-endpoint-test 0000:01:00.0: Failed to request IRQ 30 for MSI 3
SET IRQ TYPE TO MSI-X: NOT OKAY
Fix this issue by using "test->irq_type" instead of global "irq_type".
Cc: stable@vger.kernel.org
Fixes: b2ba9225e0 ("misc: pci_endpoint_test: Avoid using module parameter to determine irqtype")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250225110252.28866-4-hayashi.kunihiko@socionext.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
After devm_request_irq() fails with error in pci_endpoint_test_request_irq(),
the pci_endpoint_test_free_irq_vectors() is called assuming that all IRQs
have been released.
However, some requested IRQs remain unreleased, so there are still
/proc/irq/* entries remaining, and this results in WARN() with the
following message:
remove_proc_entry: removing non-empty directory 'irq/30', leaking at least 'pci-endpoint-test.0'
WARNING: CPU: 0 PID: 202 at fs/proc/generic.c:719 remove_proc_entry +0x190/0x19c
To solve this issue, set the number of remaining IRQs to test->num_irqs,
and release IRQs in advance by calling pci_endpoint_test_release_irq().
Cc: stable@vger.kernel.org
Fixes: e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250225110252.28866-3-hayashi.kunihiko@socionext.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Running 'pcitest -b 0' fails with "TEST FAILED" when the BAR0 size
is e.g. 8 GB.
The return value of the pci_resource_len() macro can be larger than that
of a signed integer type. Thus, when using 'pcitest' with an 8 GB BAR,
the bar_size of the integer type will overflow.
Change bar_size from integer to resource_size_t to prevent integer
overflow for large BAR sizes with 32-bit compilers.
In order to handle 64-bit resource_type_t on 32-bit platforms, we would
have needed to use a function like div_u64() or similar. Instead, change
the code to use addition instead of division. This avoids the need for
div_u64() or similar, while also simplifying the code.
Fixes: cda370ec6d ("misc: pci_endpoint_test: Avoid using hard-coded BAR sizes")
Co-developed-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250124093300.3629624-2-cassel@kernel.org
[mani: added fixes tag]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
The current code returns -ENOMEM if test->bar[barno] is NULL.
There can be two reasons why test->bar[barno] is NULL:
1) The pci_ioremap_bar() call in pci_endpoint_test_probe() failed.
2) The BAR was skipped, because it is disabled by the endpoint.
Many PCI endpoint controller drivers will disable all BARs in their
init function. A disabled BAR will have a size of 0.
A PCI endpoint function driver will be able to enable any BAR that
is not marked as BAR_RESERVED (which means that the BAR should not
be touched by the EPF driver).
Thus, perform check if the size is 0, before checking if
test->bar[barno] is NULL, such that we can return different errors.
This will allow the selftests to return SKIP instead of FAIL for
disabled BARs.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250123120147.3603409-3-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Increase the size of the string buffer to avoid potential truncation in
pci_endpoint_test_probe().
This fixes the following build warning when compiling with W=1:
drivers/misc/pci_endpoint_test.c:29:49: note: directive argument in the range [0, 2147483647]
29 | #define DRV_MODULE_NAME "pci-endpoint-test"
| ^~~~~~~~~~~~~~~~~~~
drivers/misc/pci_endpoint_test.c:998:38: note: in expansion of macro ‘DRV_MODULE_NAME’
998 | snprintf(name, sizeof(name), DRV_MODULE_NAME ".%d", id);
| ^~~~~~~~~~~~~~~
drivers/misc/pci_endpoint_test.c:998:9: note: ‘snprintf’ output between 20 and 29 bytes into a destination of size 24
998 | snprintf(name, sizeof(name), DRV_MODULE_NAME ".%d", id);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250123103127.3581432-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Commit f26d37ee9b ("misc: pci_endpoint_test: Fix IOCTL return value")
changed the return value of pci_endpoint_test_bars_read_bar() from false
to -EINVAL on error, however, it failed to update the error handling.
Fixes: f26d37ee9b ("misc: pci_endpoint_test: Fix IOCTL return value")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250204110640.570823-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add GET_IRQTYPE API checks to each interrupt test.
While at it, change pci_ep_ioctl() to get the appropriate return
value from ioctl().
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20250225110252.28866-2-hayashi.kunihiko@socionext.com
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Currently BARs that have been disabled by the endpoint controller driver
will result in a test FAIL.
Returning FAIL for a BAR that is disabled seems overly pessimistic.
There are EPC that disables one or more BARs intentionally.
One reason for this is that there are certain EPCs that are hardwired to
expose internal PCIe controller registers over a certain BAR, so the EPC
driver disables such a BAR, such that the host will not overwrite random
registers during testing.
Such a BAR will be disabled by the EPC driver's init function, and the
BAR will be marked as BAR_RESERVED, such that it will be unavailable to
endpoint function drivers.
Let's return FAIL only for BARs that are actually enabled and failed the
test, and let's return skip for BARs that are not even enabled.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250123120147.3603409-4-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
e19bde2269 ("selftests: Move PCI Endpoint tests from tools/pci to
Kselftests") moves tools/pci/ to tools/testing/selftests/pci_endpoint,
which causes build failure when running "make pci" under tools:
linux/tools$ make pci
DESCEND pci
make[1]: *** No targets specified and no makefile found. Stop.
make: *** [Makefile:73: pci] Error 2
Update the top level tools/Makefile to remove reference to building,
installing and cleaning pci components.
Link: https://lore.kernel.org/r/20250217115159.537920-1-liujianfeng1994@gmail.com
Fixes: e19bde2269 ("selftests: Move PCI Endpoint tests from tools/pci to Kselftests")
Signed-off-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be an array of VDSO clocks.
Now that all preparatory changes are in place:
Split the clock related struct members into a separate struct
vdso_clock. Make sure all users are aware, that vdso_time_data is no longer
initialized as an array and vdso_clock is now the array inside
vdso_data. Remove the vdso_clock define, which mapped it to vdso_time_data
for the transition.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-19-c1b5c69a166f@linutronix.de
Architecture related vdso data is required in the fast path when reading
CLOCK_MONOTONIC or CLOCK_REALTIME. At the moment, this information is
located at the end of the vdso_time_data structure, which is a suboptimal
cache layout.
Move the architecture specific VDSO data right before the basetime
information, which is always required. This change does not have an impact
on architectures with CONFIG_ARCH_HAS_VDSO_DATA=n. Architectures, which
have it enabled, gain a better cache layout.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-18-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-17-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-16-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-15-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-14-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
For time namespaces, vdso_time_data needs to be set up. But only the clock
related part of the vdso_data thats requires this setup. To reflect the
future struct vdso_clock, rename timens_setup_vdso_data() to
timns_setup_vdso_clock_data().
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-13-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-12-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
To prepare for the rework of the data structures, replace the struct
vdso_time_data pointer argument of the helper functions with struct
vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-11-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare for the rework of these structures by adding a struct vdso_clock
pointer argument to do_coarse_time_ns(), and replace the struct
vdso_time_data pointer with the new pointer argument where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-10-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare for the rework of these structures by adding a struct vdso_clock
pointer argument to do_coarse(), and replace the struct vdso_time_data
pointer with the new pointer argument where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-9-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare for the rework of these structures by adding a struct vdso_clock
pointer argument to do_hres_timens(), and replace the struct vdso_time_data
pointer with the new pointer argument where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-8-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare for the rework of these structures by adding a struct vdso_clock
pointer argument to do_hres(), and replace the struct vdso_time_data
pointer with the new pointer argument where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-7-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be array of VDSO clocks. At the moment,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare all functions which need the pointer to the vdso_clock array to
work correctly after introducing the new struct. Where applicable, replace
the struct vdso_time_data pointer by a struct vdso_clock pointer.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-6-c1b5c69a166f@linutronix.de
To support multiple PTP clocks, the VDSO data structure needs to be
reworked. All clock specific data will end up in struct vdso_clock and in
struct vdso_time_data there will be an array of VDSO clocks. For now,
vdso_clock is simply a define which maps vdso_clock to vdso_time_data.
Prepare all functions which need the pointer to the vdso_clock array to
work well after the structures get reworked. Replace the struct vdso_time_data
pointer with a struct vdso_clock pointer where applicable.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-5-c1b5c69a166f@linutronix.de
Multiple PTP clocks, which are independent of timekeeping, are required for
systems, which utilize PTP for synchronizing e.g. automation systems
independent of clock TAI.
PTP clocks are slow to access, but applications require fast access to the
relevant time similar to the regular timekeeping relevant clocks.
To prepare for that the VDSO data representation must be reworked. For
transition to the new structure of the vdso, add a define which maps
vdso_clock to vdso_data. This will be removed when all users are updated
step by step.
No functional change.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-4-c1b5c69a166f@linutronix.de
vdso_time_data is not cacheline aligned at the moment. When instantiating
an array, the start of the second array member is not cache line aligned.
This increases the number of the required cache lines which needs to be
read when handling e.g. CLOCK_MONOTONIC_RAW, because the data spawns an
extra cache line if the previous data does not end at a cache line
boundary.
Therefore make struct vdso_time_data cacheline aligned.
Signed-off-by: Anna-Maria Behnsen <anna-maria@linutronix.de>
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250303-vdso-clock-v1-3-c1b5c69a166f@linutronix.de