Commit c77fb5fe6f ("KVM: x86: Allow the guest to run with dirty debug
registers") allows the guest accessing to DRs without exiting when
KVM_DEBUGREG_WONT_EXIT and we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before the commit.
But the commit sets the hardware DR6 not only when KVM_DEBUGREG_WONT_EXIT,
but also when KVM_DEBUGREG_BP_ENABLED. The second case is unnecessary
and just leads to a more case which leaks stale DR6 to the host which has
to be resolved by unconditionally reseting DR6 in kvm_arch_vcpu_put().
Even if KVM_DEBUGREG_WONT_EXIT, however, setting the host DR6 only matters
on VMX because SVM always uses the DR6 value from the VMCB. So move this
line to vmx.c and make it conditional on KVM_DEBUGREG_WONT_EXIT.
Reported-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit ae561edeb4 ("KVM: x86: DR0-DR3 are not clear on reset") added code to
ensure eff_db are updated when they're modified through non-standard paths.
But there is no reason to also update hardware DRs unless hardware breakpoints
are active or DR exiting is disabled, and in those cases updating hardware is
handled by KVM_DEBUGREG_WONT_EXIT and KVM_DEBUGREG_BP_ENABLED.
KVM_DEBUGREG_RELOAD just causes unnecesarry load of hardware DRs and is better
to be removed.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20210809174307.145263-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add yet another spinlock for the TDP MMU and take it when marking indirect
shadow pages unsync. When using the TDP MMU and L1 is running L2(s) with
nested TDP, KVM may encounter shadow pages for the TDP entries managed by
L1 (controlling L2) when handling a TDP MMU page fault. The unsync logic
is not thread safe, e.g. the kvm_mmu_page fields are not atomic, and
misbehaves when a shadow page is marked unsync via a TDP MMU page fault,
which runs with mmu_lock held for read, not write.
Lack of a critical section manifests most visibly as an underflow of
unsync_children in clear_unsync_child_bit() due to unsync_children being
corrupted when multiple CPUs write it without a critical section and
without atomic operations. But underflow is the best case scenario. The
worst case scenario is that unsync_children prematurely hits '0' and
leads to guest memory corruption due to KVM neglecting to properly sync
shadow pages.
Use an entirely new spinlock even though piggybacking tdp_mmu_pages_lock
would functionally be ok. Usurping the lock could degrade performance when
building upper level page tables on different vCPUs, especially since the
unsync flow could hold the lock for a comparatively long time depending on
the number of indirect shadow pages and the depth of the paging tree.
For simplicity, take the lock for all MMUs, even though KVM could fairly
easily know that mmu_lock is held for write. If mmu_lock is held for
write, there cannot be contention for the inner spinlock, and marking
shadow pages unsync across multiple vCPUs will be slow enough that
bouncing the kvm_arch cacheline should be in the noise.
Note, even though L2 could theoretically be given access to its own EPT
entries, a nested MMU must hold mmu_lock for write and thus cannot race
against a TDP MMU page fault. I.e. the additional spinlock only _needs_ to
be taken by the TDP MMU, as opposed to being taken by any MMU for a VM
that is running with the TDP MMU enabled. Holding mmu_lock for read also
prevents the indirect shadow page from being freed. But as above, keep
it simple and always take the lock.
Alternative #1, the TDP MMU could simply pass "false" for can_unsync and
effectively disable unsync behavior for nested TDP. Write protecting leaf
shadow pages is unlikely to noticeably impact traditional L1 VMMs, as such
VMMs typically don't modify TDP entries, but the same may not hold true for
non-standard use cases and/or VMMs that are migrating physical pages (from
L1's perspective).
Alternative #2, the unsync logic could be made thread safe. In theory,
simply converting all relevant kvm_mmu_page fields to atomics and using
atomic bitops for the bitmap would suffice. However, (a) an in-depth audit
would be required, (b) the code churn would be substantial, and (c) legacy
shadow paging would incur additional atomic operations in performance
sensitive paths for no benefit (to legacy shadow paging).
Fixes: a2855afc7e ("KVM: x86/mmu: Allow parallel page faults for the TDP MMU")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812181815.3378104-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set the min_level for the TDP iterator at the root level when zapping all
SPTEs to optimize the iterator's try_step_down(). Zapping a non-leaf
SPTE will recursively zap all its children, thus there is no need for the
iterator to attempt to step down. This avoids rereading the top-level
SPTEs after they are zapped by causing try_step_down() to short-circuit.
In most cases, optimizing try_step_down() will be in the noise as the cost
of zapping SPTEs completely dominates the overall time. The optimization
is however helpful if the zap occurs with relatively few SPTEs, e.g. if KVM
is zapping in response to multiple memslot updates when userspace is adding
and removing read-only memslots for option ROMs. In that case, the task
doing the zapping likely isn't a vCPU thread, but it still holds mmu_lock
for read and thus can be a noisy neighbor of sorts.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812181414.3376143-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass "all ones" as the end GFN to signal "zap all" for the TDP MMU and
really zap all SPTEs in this case. As is, zap_gfn_range() skips non-leaf
SPTEs whose range exceeds the range to be zapped. If shadow_phys_bits is
not aligned to the range size of top-level SPTEs, e.g. 512gb with 4-level
paging, the "zap all" flows will skip top-level SPTEs whose range extends
beyond shadow_phys_bits and leak their SPs when the VM is destroyed.
Use the current upper bound (based on host.MAXPHYADDR) to detect that the
caller wants to zap all SPTEs, e.g. instead of using the max theoretical
gfn, 1 << (52 - 12). The more precise upper bound allows the TDP iterator
to terminate its walk earlier when running on hosts with MAXPHYADDR < 52.
Add a WARN on kmv->arch.tdp_mmu_pages when the TDP MMU is destroyed to
help future debuggers should KVM decide to leak SPTEs again.
The bug is most easily reproduced by running (and unloading!) KVM in a
VM whose host.MAXPHYADDR < 39, as the SPTE for gfn=0 will be skipped.
=============================================================================
BUG kvm_mmu_page_header (Not tainted): Objects remaining in kvm_mmu_page_header on __kmem_cache_shutdown()
-----------------------------------------------------------------------------
Slab 0x000000004d8f7af1 objects=22 used=2 fp=0x00000000624d29ac flags=0x4000000000000200(slab|zone=1)
CPU: 0 PID: 1582 Comm: rmmod Not tainted 5.14.0-rc2+ #420
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
dump_stack_lvl+0x45/0x59
slab_err+0x95/0xc9
__kmem_cache_shutdown.cold+0x3c/0x158
kmem_cache_destroy+0x3d/0xf0
kvm_mmu_module_exit+0xa/0x30 [kvm]
kvm_arch_exit+0x5d/0x90 [kvm]
kvm_exit+0x78/0x90 [kvm]
vmx_exit+0x1a/0x50 [kvm_intel]
__x64_sys_delete_module+0x13f/0x220
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: faaf05b00a ("kvm: x86/mmu: Support zapping SPTEs in the TDP MMU")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812181414.3376143-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The "mct_tick" is a per-cpu clockevents device. Set the
CLOCK_EVT_FEAT_PERCPU feature to prevent e.g. mct_tick0 being unsafely
designated as the global broadcast timer and instead treat the device as
a per-cpu wakeup timer.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-3-will@kernel.org
All arm64 CPUs feature an architected timer, which offers a relatively
low-latency interface to a per-cpu clocksource and timer. For the most
part, using this interface is a no-brainer, with the exception of SoCs
where it cannot be used to wake up from deep idle state (i.e.
CLOCK_EVT_FEAT_C3STOP is set).
On the contrary, the Exynos MCT is extremely slow to access yet can be
used as a wakeup source. In preparation for using the Exynos MCT as a
potential wakeup timer for the Arm architected timer, reduce its ratings
so that the architected timer is preferred.
This effectively reverts the decision made in 6282edb72b
("clocksource/drivers/exynos_mct: Increase priority over ARM arch timer")
for arm64, as the reasoning for the original change was to work around
a 32-bit SoC design.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> # exynos-5422
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210608154341.10794-2-will@kernel.org
- Plug race between enabling MTE and creating vcpus
- Fix off-by-one bug when checking whether an address range is RAM
-----BEGIN PGP SIGNATURE-----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=hL2s
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.14, take #2
- Plug race between enabling MTE and creating vcpus
- Fix off-by-one bug when checking whether an address range is RAM
Use vmx_need_pf_intercept() when determining if L0 wants to handle a #PF
in L2 or if the VM-Exit should be forwarded to L1. The current logic fails
to account for the case where #PF is intercepted to handle
guest.MAXPHYADDR < host.MAXPHYADDR and ends up reflecting all #PFs into
L1. At best, L1 will complain and inject the #PF back into L2. At
worst, L1 will eat the unexpected fault and cause L2 to hang on infinite
page faults.
Note, while the bug was technically introduced by the commit that added
support for the MAXPHYADDR madness, the shame is all on commit
a0c134347b ("KVM: VMX: introduce vmx_need_pf_intercept").
Fixes: 1dbf5d68af ("KVM: VMX: Add guest physical address check in EPT violation and misconfig")
Cc: stable@vger.kernel.org
Cc: Peter Shier <pshier@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812045615.3167686-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a nested EPT violation/misconfig is injected into the guest,
the shadow EPT PTEs associated with that address need to be synced.
This is done by kvm_inject_emulated_page_fault() before it calls
nested_ept_inject_page_fault(). However, that will only sync the
shadow EPT PTE associated with the current L1 EPTP. Since the ASID
is based on EP4TA rather than the full EPTP, so syncing the current
EPTP is not enough. The SPTEs associated with any other L1 EPTPs
in the prev_roots cache with the same EP4TA also need to be synced.
Signed-off-by: Junaid Shahid <junaids@google.com>
Message-Id: <20210806222229.1645356-1-junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hv_vcpu is initialized again a dozen lines below, and at this
point vcpu->arch.hyperv is not valid. Remove the initializer.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove an ancient restriction that disallowed exposing EFER.NX to the
guest if EFER.NX=0 on the host, even if NX is fully supported by the CPU.
The motivation of the check, added by commit 2cc51560ae ("KVM: VMX:
Avoid saving and restoring msr_efer on lightweight vmexit"), was to rule
out the case of host.EFER.NX=0 and guest.EFER.NX=1 so that KVM could run
the guest with the host's EFER.NX and thus avoid context switching EFER
if the only divergence was the NX bit.
Fast forward to today, and KVM has long since stopped running the guest
with the host's EFER.NX. Not only does KVM context switch EFER if
host.EFER.NX=1 && guest.EFER.NX=0, KVM also forces host.EFER.NX=0 &&
guest.EFER.NX=1 when using shadow paging (to emulate SMEP). Furthermore,
the entire motivation for the restriction was made obsolete over a decade
ago when Intel added dedicated host and guest EFER fields in the VMCS
(Nehalem timeframe), which reduced the overhead of context switching EFER
from 400+ cycles (2 * WRMSR + 1 * RDMSR) to a mere ~2 cycles.
In practice, the removed restriction only affects non-PAE 32-bit kernels,
as EFER.NX is set during boot if NX is supported and the kernel will use
PAE paging (32-bit or 64-bit), regardless of whether or not the kernel
will actually use NX itself (mark PTEs non-executable).
Alternatively and/or complementarily, startup_32_smp() in head_32.S could
be modified to set EFER.NX=1 regardless of paging mode, thus eliminating
the scenario where NX is supported but not enabled. However, that runs
the risk of breaking non-KVM non-PAE kernels (though the risk is very,
very low as there are no known EFER.NX errata), and also eliminates an
easy-to-use mechanism for stressing KVM's handling of guest vs. host EFER
across nested virtualization transitions.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210805183804.1221554-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add serial driver data for Exynos850 SoC. This driver data is basically
reusing EXYNOS_COMMON_SERIAL_DRV_DATA, which is common for all Exynos
chips, but also enables USI init, which was added in previous commit:
"tty: serial: samsung: Init USI to keep clocks running".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-7-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make checkpatch happy by fixing this error:
ERROR: Macros with complex values should be enclosed in parentheses
Although this change is made to keep macros consistent with consequent
patches (adding driver data for new SoC), it's intentionally added as a
separate patch to ease possible porting efforts in future.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-6-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART block is a part of USI (Universal Serial Interface) IP-core in
Samsung SoCs since Exynos9810 (e.g. in Exynos850). USI allows one to
enable one of three types of serial interface: UART, SPI or I2C. That's
possible because USI shares almost all internal circuits within each
protocol. USI also provides some additional registers so it's possible
to configure it.
One USI register called USI_OPTION has reset value of 0x0. Because of
this the clock gating behavior is controlled by hardware (HWACG =
Hardware Auto Clock Gating), which simply means the serial won't work
after reset as is. In order to make it work, USI_OPTION[2:1] bits must
be set to 0b01, so that HWACG is controlled manually (by software).
Bits meaning:
- CLKREQ_ON = 1: clock is continuously provided to IP
- CLKSTOP_ON = 0: drive IP_CLKREQ to High (needs to be set along with
CLKREQ_ON = 1)
USI is not present on older chips, like s3c2410, s3c2412, s3c2440,
s3c6400, s5pv210, exynos5433, exynos4210. So the new boolean field
'.has_usi' was added to struct s3c24xx_uart_info. USI registers will be
only actually accessed when '.has_usi' field is set to "1".
This feature is needed for further serial enablement on Exynos850, but
some other new Exynos chips (like Exynos9810) may benefit from this
feature as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-5-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serdev provides a generic helper to get UART Serial Bus resources.
Use it instead of an open coded variant.
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210806111736.66591-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as for I²C Serial Bus resource split and export
serdev_acpi_get_uart_resource(). We have already a few users
one of which is converted here.
Rationale of this is to consolidate parsing UART Serial Bus
resource in one place as it's done, e.g., for I²C Serial Bus.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210806111736.66591-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function stm32_usart_init_port, intent of the code maybe when
irq returns a value of zero, the return should be '-ENODEV'. But the
conditional expression '? :' maybe clerical error, it should be
'?:' to make '-ENODEV' work.
But in fact, as the example in platform.c is
* int irq = platform_get_irq(pdev, 0);
* if (irq < 0)
* return irq;
So the return value of zero is unnecessary to check, at last remove
the unnecessary '?: -ENODEV'.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210811105136.25392-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 188db4435a ("usb: gadget: s3c: use platform resources")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/bd69b22c-b484-5a1f-c798-78d4b78405f2@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc3_qcom_acpi_register_core(), the driver neglects to check the result
of platform_get_irq()'s call and blithely assigns the negative error codes
to the allocated child device's IRQ resource and then passing this resource
to platform_device_add_resources() and later causing dwc3_otg_get_irq() to
fail anyway. Stop calling platform_device_add_resources() with the invalid
IRQ #s, so that there's less complexity in the IRQ error checking.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/45fec3da-1679-5bfe-5d74-219ca3fb28e7@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: f90db10779 ("usb: dwc3: meson-g12a: Add support for IRQ based OTG switching")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/96106462-5538-0b2f-f2ab-ee56e4853912@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 987219ad34 ("staging: r8188eu: remove lines from Makefile
that silence build warnings"), clang warns:
drivers/staging/r8188eu/os_dep/usb_intf.c:726:6: warning: variable
'status' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (!if1) {
^~~~
drivers/staging/r8188eu/os_dep/usb_intf.c:741:6: note: uninitialized use
occurs here
if (status != _SUCCESS)
^~~~~~
drivers/staging/r8188eu/os_dep/usb_intf.c:726:2: note: remove the 'if'
if its condition is always false
if (!if1) {
^~~~~~~~~~~
drivers/staging/r8188eu/os_dep/usb_intf.c:714:12: note: initialize the
variable 'status' to silence this warning
int status;
^
= 0
1 warning generated.
status is not initialized if the call to usb_dvobj_init() or
rtw_usb_if1_init() fails.
Looking at the error function as a whole, the error handling is odd
compared to the rest of the kernel, which prefers to set error codes on
goto paths, rather than a global "status" variable which determines the
error code at the end of the function and function calls in the case of
error.
Rearrange the error handling of this function to bring it more inline
with how the kernel does it in most cases, which helps readability.
The call to rtw_usb_if1_deinit() is eliminated because it is not
possible to ever hit it; if rtw_usb_if1_init() fails, the goto call
jumps over the call to rtw_usb_if1_deinit() and in the success case,
status is set to _SUCCESS.
Acked-by: Phillip Potter <phil@philpotter.co.uk>
Acked-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210812204027.338872-4-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 987219ad34 ("staging: r8188eu: remove lines from Makefile
that silence build warnings"), clang warns:
drivers/staging/r8188eu/core/rtw_recv.c:499:8: warning: variable
'ether_type' is uninitialized when used here [-Wuninitialized]
if (ether_type == eapol_type)
^~~~~~~~~~
drivers/staging/r8188eu/core/rtw_recv.c:458:16: note: initialize the
variable 'ether_type' to silence this warning
u16 ether_type;
^
= 0
1 warning generated.
This if statement sets the exact same assignment as above so just remove
it.
Acked-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210812204027.338872-3-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 987219ad34 ("staging: r8188eu: remove lines from Makefile
that silence build warnings"), clang warns several times:
In file included from
drivers/staging/r8188eu/os_dep/../include/drv_types.h:22:
drivers/staging/r8188eu/os_dep/../include/rtw_recv.h:395:9: warning:
variable 'buf_desc' is uninitialized when used here [-Wuninitialized]
return buf_desc;
^~~~~~~~
drivers/staging/r8188eu/os_dep/../include/rtw_recv.h:391:25: note:
initialize the variable 'buf_desc' to silence this warning
unsigned char *buf_desc;
^
= NULL
drivers/staging/r8188eu/os_dep/../include/rtw_recv.h:412:52: warning:
variable 'buf_star' is uninitialized when used here [-Wuninitialized]
precv_frame = rxmem_to_recvframe((unsigned char *)buf_star);
^~~~~~~~
drivers/staging/r8188eu/os_dep/../include/rtw_recv.h:410:14: note:
initialize the variable 'buf_star' to silence this warning
u8 *buf_star;
^
= NULL
2 warnings generated.
The functions that these warnings come from are not used or are called
from functions that are not used so just remove them to remove the
warnings.
Acked-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210812204027.338872-2-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace custom hwaddr_aton_i() with mac_pton() in core/ioctl_linux.c
and remove the now unused functions hwaddr_aton_i() and hex2num_i().
Acked-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20210812132057.22579-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the register values set for type detection cause pops during suspend,
ensure these are cleaned up after type detection completes, as well
ensuring that these are cleared when we suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210812183433.6330-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The permission check in gfs2_setattr is an old and outdated version of
may_setattr(). Switch to the updated version.
Fixes fstest generic/079.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Move the permission checks in notify_change into a separate function to
make them available to filesystems.
When notify_change is called, the vfs performs those checks before
calling into iop->setattr. However, a filesystem like gfs2 can only
lock and revalidate the inode inside ->setattr, and it must then repeat
those checks to err on the safe side.
It would be nice to get rid of the double checking, but moving the
permission check into iop->setattr altogether isn't really an option.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
can and ieee802154.
Current release - regressions:
- r8169: fix ASPM-related link-up regressions
- bridge: fix flags interpretation for extern learn fdb entries
- phy: micrel: fix link detection on ksz87xx switch
- Revert "tipc: Return the correct errno code"
- ptp: fix possible memory leak caused by invalid cast
Current release - new code bugs:
- bpf: add missing bpf_read_[un]lock_trace() for syscall program
- bpf: fix potentially incorrect results with bpf_get_local_storage()
- page_pool: mask the page->signature before the checking, avoid
dma mapping leaks
- netfilter: nfnetlink_hook: 5 fixes to information in netlink dumps
- bnxt_en: fix firmware interface issues with PTP
- mlx5: Bridge, fix ageing time
Previous releases - regressions:
- linkwatch: fix failure to restore device state across suspend/resume
- bareudp: fix invalid read beyond skb's linear data
Previous releases - always broken:
- bpf: fix integer overflow involving bucket_size
- ppp: fix issues when desired interface name is specified via netlink
- wwan: mhi_wwan_ctrl: fix possible deadlock
- dsa: microchip: ksz8795: fix number of VLAN related bugs
- dsa: drivers: fix broken backpressure in .port_fdb_dump
- dsa: qca: ar9331: make proper initial port defaults
Misc:
- bpf: add lockdown check for probe_write_user helper
- netfilter: conntrack: remove offload_pickup sysctl before 5.14 is out
- netfilter: conntrack: collect all entries in one cycle,
heuristically slow down garbage collection scans
on idle systems to prevent frequent wake ups
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=hzDl
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter, bpf, can and
ieee802154.
The size of this is pretty normal, but we got more fixes for 5.14
changes this week than last week. Nothing major but the trend is the
opposite of what we like. We'll see how the next week goes..
Current release - regressions:
- r8169: fix ASPM-related link-up regressions
- bridge: fix flags interpretation for extern learn fdb entries
- phy: micrel: fix link detection on ksz87xx switch
- Revert "tipc: Return the correct errno code"
- ptp: fix possible memory leak caused by invalid cast
Current release - new code bugs:
- bpf: add missing bpf_read_[un]lock_trace() for syscall program
- bpf: fix potentially incorrect results with bpf_get_local_storage()
- page_pool: mask the page->signature before the checking, avoid dma
mapping leaks
- netfilter: nfnetlink_hook: 5 fixes to information in netlink dumps
- bnxt_en: fix firmware interface issues with PTP
- mlx5: Bridge, fix ageing time
Previous releases - regressions:
- linkwatch: fix failure to restore device state across
suspend/resume
- bareudp: fix invalid read beyond skb's linear data
Previous releases - always broken:
- bpf: fix integer overflow involving bucket_size
- ppp: fix issues when desired interface name is specified via
netlink
- wwan: mhi_wwan_ctrl: fix possible deadlock
- dsa: microchip: ksz8795: fix number of VLAN related bugs
- dsa: drivers: fix broken backpressure in .port_fdb_dump
- dsa: qca: ar9331: make proper initial port defaults
Misc:
- bpf: add lockdown check for probe_write_user helper
- netfilter: conntrack: remove offload_pickup sysctl before 5.14 is
out
- netfilter: conntrack: collect all entries in one cycle,
heuristically slow down garbage collection scans on idle systems to
prevent frequent wake ups"
* tag 'net-5.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
vsock/virtio: avoid potential deadlock when vsock device remove
wwan: core: Avoid returning NULL from wwan_create_dev()
net: dsa: sja1105: unregister the MDIO buses during teardown
Revert "tipc: Return the correct errno code"
net: mscc: Fix non-GPL export of regmap APIs
net: igmp: increase size of mr_ifc_count
MAINTAINERS: switch to my OMP email for Renesas Ethernet drivers
tcp_bbr: fix u32 wrap bug in round logic if bbr_init() called after 2B packets
net: pcs: xpcs: fix error handling on failed to allocate memory
net: linkwatch: fix failure to restore device state across suspend/resume
net: bridge: fix memleak in br_add_if()
net: switchdev: zero-initialize struct switchdev_notifier_fdb_info emitted by drivers towards the bridge
net: bridge: fix flags interpretation for extern learn fdb entries
net: dsa: sja1105: fix broken backpressure in .port_fdb_dump
net: dsa: lantiq: fix broken backpressure in .port_fdb_dump
net: dsa: lan9303: fix broken backpressure in .port_fdb_dump
net: dsa: hellcreek: fix broken backpressure in .port_fdb_dump
bpf, core: Fix kernel-doc notation
net: igmp: fix data-race in igmp_ifc_timer_expire()
net: Fix memory leak in ieee802154_raw_deliver
...
and a reference handling fix from Jeff that should address some memory
corruption reports in the snaprealm area. Both marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmEVaqsTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi/DBCACd7+mnAXIwajwoDdXFIJT7/tfimdvU
cMrh6ciZNtEKxm23flQ1AFJXlXR/nlZRspfOmlmsl9bB4TAlXnhJ/s4JaiuOMMTh
OQ4oz0vAbGELkPsXB/FXGSSk1wTFEjCocFsJwoYiUkYjD7Qt12BZKNkFYgj/MVc2
wyJ5K1buqBLVFDU+CymqDzc07YpG1zn888o7UGWFTyevldRAHl2euxqbnr0S4qb9
OS5UKO3aFCEt5PT9RKRHygCGjuHym/fgXgPm9aNY4rYBE9qOXloVUOD5bhMHBJ2E
g506xhOurqbGv4O9oj+gvBwtQwY/TF8BvCA79koQSHNIYQsC/bcXenST
=m8x8
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.14-rc6' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to avoid a soft lockup in ceph_check_delayed_caps() from Luis
and a reference handling fix from Jeff that should address some memory
corruption reports in the snaprealm area.
Both marked for stable"
* tag 'ceph-for-5.14-rc6' of git://github.com/ceph/ceph-client:
ceph: take snap_empty_lock atomically with snaprealm refcount change
ceph: reduce contention in ceph_check_delayed_caps()
amdgpu:
- Yellow carp update
- RAS EEPROM fixes
- BACO/BOCO fixes
- Fix a memory leak in an error path
- Freesync fix
- VCN harvesting fix
- Display fixes
i915:
- GVT fix for Windows VM hang.
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
mediatek:
- Fix dpi bridge bug.
- Fix cursor plane no update.
meson:
- Fix colors when booting with HDR
-----BEGIN PGP SIGNATURE-----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=w0XU
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2021-08-13' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Another week, another set of pretty regular fixes, nothing really
stands out too much.
amdgpu:
- Yellow carp update
- RAS EEPROM fixes
- BACO/BOCO fixes
- Fix a memory leak in an error path
- Freesync fix
- VCN harvesting fix
- Display fixes
i915:
- GVT fix for Windows VM hang.
- Display fix of 12 BPC bits for display 12 and newer.
- Don't try to access some media register for fused off domains.
- Fix kerneldoc build warnings.
mediatek:
- Fix dpi bridge bug.
- Fix cursor plane no update.
meson:
- Fix colors when booting with HDR"
* tag 'drm-fixes-2021-08-13' of git://anongit.freedesktop.org/drm/drm:
drm/doc/rfc: drop lmem uapi section
drm/i915: Only access SFC_DONE when media domain is not fused off
drm/i915/display: Fix the 12 BPC bits for PIPE_MISC reg
drm/amd/display: use GFP_ATOMIC in amdgpu_dm_irq_schedule_work
drm/amd/display: Remove invalid assert for ODM + MPC case
drm/amd/pm: bug fix for the runtime pm BACO
drm/amdgpu: handle VCN instances when harvesting (v2)
drm/meson: fix colour distortion from HDR set during vendor u-boot
drm/i915/gvt: Fix cached atomics setting for Windows VM
drm/amdgpu: Add preferred mode in modeset when freesync video mode's enabled.
drm/amd/pm: Fix a memory leak in an error handling path in 'vangogh_tables_init()'
drm/amdgpu: don't enable baco on boco platforms in runpm
drm/amdgpu: set RAS EEPROM address from VBIOS
drm/amd/pm: update smu v13.0.1 firmware header
drm/mediatek: Fix cursor plane no update
drm/mediatek: mtk-dpi: Set out_fmt from config if not the last bridge
drm/mediatek: dpi: Fix NULL dereference in mtk_dpi_bridge_atomic_check
Add initial version of device tree for Facebook Fuji (AST2600) BMC.
Fuji is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-7-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Elbert (AST2600) BMC.
Elbert is Facebook's next generation switch platform with an AST2600 BMC
integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-6-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add initial version of device tree for Facebook Cloudripper (AST2600) BMC.
Cloudripper is Facebook's next generation switch platform with an AST2600
BMC integrated for health monitoring purpose.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-5-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This common descirption is included by all Facebook AST2600 Network BMC
platforms to minimize duplicated device entries across Facebook Network
BMC device trees.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-4-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Simplify wedge400 flash layout by using the common layout defined in
"facebook-bmc-flash-layout-128.dtsi".
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-3-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This is the layout used by Facebook BMC systems. It describes the fixed
flash layout of a 128MB mtd device.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210805222818.8391-2-rentao.bupt@gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
ksmbd start supporting SMB3 Multi-channel feature. Mark it as Partially
supported till replay/retry mechanisms are implemented.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
if server shutdown happens in the situation that
there are connections, workqueue could be destroyed
before queueing disconnect work.
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
ksmbd is forcing to turn on FS_POSIX_ACL in Kconfig to use vfs acl
functions(posix_acl_alloc, get_acl, set_posix_acl). OpenWRT and other
platform doesn't use acl and this config is disable by default in
kernel. This patch use IS_ENABLED() to know acl config is enable and use
acl function if it is enable.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Use proper errno instead of -1 in smb2_get_ksmbd_tcon().
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Steve French <stfrench@microsoft.com>