Add support of rule offloading added to the non-zero index chain,
which was previously forbidden. Also, goto action is offloaded
allowing to jump for processing of desired chain.
Note that only implicit chain 0 is bound to the device port(s) for
processing. The rest of chains have to be jumped by actions.
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar says:
====================
net: wwan: debugfs dev reference not dropped
This patch series contains WWAN subsystem & IOSM Driver changes to
drop dev reference obtained as part of wwan debugfs dir entry retrieval.
PATCH1: A new debugfs interface is introduced in wwan subsystem so
that wwan driver can drop the obtained dev reference post debugfs use.
PATCH2: IOSM Driver uses new debugfs interface to drop dev reference.
Please refer to commit messages for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Post debugfs use call wwan_put_debugfs_dir()to drop
debugfs dev reference.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WWAN driver call's wwan_get_debugfs_dir() to obtain
WWAN debugfs dir entry. As part of this procedure it
returns a reference to a found device.
Since there is no debugfs interface available at WWAN
subsystem, it is not possible to drop dev reference post
debugfs use. This leads to side effects like post wwan
driver load and reload the wwan instance gets increment
from wwanX to wwanX+1.
A new debugfs interface is added in wwan subsystem so that
wwan driver can drop the obtained dev reference post debugfs
use.
void wwan_put_debugfs_dir(struct dentry *dir)
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luiz Angelo Daros de Luca says:
====================
net: dsa: realtek: realtek-mdio: reset before setup
This patch series cleans the realtek-smi reset code and copy that to the
realtek-mdio.
v1-v2)
- do not run reset code block if GPIO is missing. It was printing "RESET
deasserted" even when there is no GPIO configured.
- reset switch after dsa_unregister_switch()
- demote reset messages to debug
v2-v3)
- do not assert the reset on gpiod_get. Do it explicitly aferwards.
- split the commit into two (one for each module)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices, like the switch in Banana Pi BPI R64 only starts to answer
after a HW reset. It is the same reset code from realtek-smi.
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reset GPIO was missing, the driver was still printing an info
message and still trying to assert the reset. Although gpiod_set_value()
will silently ignore calls with NULL gpio_desc, it is better to make it
clear the driver might allow gpio_desc to be NULL.
The initial value for the reset pin was changed to GPIOD_OUT_LOW,
followed by a gpiod_set_value() asserting the reset. This way, it will
be easier to spot if and where the reset really happens.
A new "asserted RESET" message was added just after the reset is
asserted, similar to the existing "deasserted RESET" message. Both
messages were demoted to dbg. The code comment is not needed anymore.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is provided by TTM now.
Also switch man->size to bytes instead of pages and fix the double
printing of size and usage in debugfs.
v2: fix size checking as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-8-christian.koenig@amd.com
This is provided by TTM now.
Also switch man->size to bytes instead of pages and fix the double
printing of size and usage in debugfs.
v2: fix size checking as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-6-christian.koenig@amd.com
Whenever rt6_uncached_list_flush_dev() swaps rt->rt6_idev
to the blackhole device, parts of IPv6 stack might still need
to increment one SNMP counter.
Root cause, patch from Ido, changelog from Eric :)
This bug suggests that we need to audit rt->rt6_idev usages
and make sure they are properly using RCU protection.
Fixes: e5f80fcf86 ("ipv6: give an IPv6 dev to blackhole_netdev")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes return value documentation of kernel_getsockname()
and kernel_getpeername() functions.
The previous documentation wrongly specified that the return
value is 0 in case of success, however sock->ops->getname returns
the length of the address in bytes in case of success.
Signed-off-by: Alex Maydanik <alexander.maydanik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource() may fail and return NULL, so check it's value
before using it.
Reported-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/all/20220117084156.9338-1-kevin3.tang@gmail.com
v1 -> v2:
- new patch
'drm' could be null in sprd_drm_shutdown, and drm_warn maybe dereference
it, remove this warning log.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/all/20220117084044.9210-1-kevin3.tang@gmail.com
v1 -> v2:
- Split checking platform_get_resource() return value to a separate patch
- Use dev_warn() instead of removing the warning log
On commit 43531edd53 ("drm/sprd: add Unisoc's drm kms master"),
adds the config DRM_SPRD, which selects DRM_KMS_CMA_HELPER.
However, commit 09717af7d1 ("drm: Remove CONFIG_DRM_KMS_CMA_HELPER
option") just removed the DRM_KMS_CMA_HELPER.
So the select DRM_KMS_CMA_HELPER refers to a non-existing kconfig symbol.
Reported-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Kevin Tang <kevin3.tang@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/all/20220117083820.6893-2-kevin3.tang@gmail.com
v1 -> v2:
- fix commit comments long lines issue and drop "On linux-next" comments
Convert the MFD part of Maxim MAX77693 MUIC to DT schema format. The
example DTS was copied from existing DTS (exynos4412-midas.dtsi), so
keep the license as GPL-2.0-only.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the regulator bindings of Maxim MAX77693 MUIC to DT schema format.
The existing bindings were defined in ../bindings/mfd/max77693.txt.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the Charger bindings of Maxim MAX77693 MUIC to DT schema format.
The existing bindings were defined in ../bindings/mfd/max77693.txt.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the LEDs bindings of Maxim MAX77693 MUIC to DT schema format.
The existing bindings were defined in ../bindings/mfd/max77693.txt.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Sebastian Andrzej Siewior says:
====================
net: dev: PREEMPT_RT fixups.
this series removes or replaces preempt_disable() and local_irq_save()
sections which are problematic on PREEMPT_RT.
Patch 2 makes netif_rx() work from any context after I found suggestions
for it in an old thread. Should that work, then the context-specific
variants could be removed.
v2…v3:
- #2
- Export __netif_rx() so it can be used by everyone.
- Add a lockdep assert to check for interrupt context.
- Update the kernel doc and mention that the skb is posted to
backlog NAPI.
- Use __netif_rx() also in drivers/net/*.c.
- Added Toke''s review tag and kept Eric's desptite the changes
made.
v1…v2:
- #1 and #2
- merge patch 1 und 2 from the series (as per Toke).
- updated patch description and corrected the first commit number (as
per Eric).
- #2
- Provide netif_rx() as in v1 and additionally __netif_rx() without
local_bh disable()+enable() for the loopback driver. __netif_rx() is
not exported (loopback is built-in only) so it won't be used
drivers. If this doesn't work then we can still export/ define a
wrapper as Eric suggested.
- Added a comment that netif_rx() considered legacy.
- #3
- Moved ____napi_schedule() into rps_ipi_queued() and
renamed it napi_schedule_rps().
https://lore.kernel.org/all/20220204201259.1095226-1-bigeasy@linutronix.de/
v1:
https://lore.kernel.org/all/20220202122848.647635-1-bigeasy@linutronix.de
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts and in the RPS case locking input_pkt_queue is
split into local_irq_disable() and optional spin_lock().
This breaks on PREEMPT_RT because the spinlock_t typed lock can not be
acquired with disabled interrupts.
The sections in which the lock is acquired is usually short in a sense that it
is not causing long und unbounded latiencies. One exception is the
skb_flow_limit() invocation which may invoke a BPF program (and may
require sleeping locks).
By moving local_irq_disable() + spin_lock() into rps_lock(), we can keep
interrupts disabled on !PREEMPT_RT and enabled on PREEMPT_RT kernels.
Without RPS on a PREEMPT_RT kernel, the needed synchronisation happens
as part of local_bh_disable() on the local CPU.
____napi_schedule() is only invoked if sd is from the local CPU. Replace
it with __napi_schedule_irqoff() which already disables interrupts on
PREEMPT_RT as needed. Move this call to rps_ipi_queued() and rename the
function to napi_schedule_rps as suggested by Jakub.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave suggested a while ago (eleven years by now) "Let's make netif_rx()
work in all contexts and get rid of netif_rx_ni()". Eric agreed and
pointed out that modern devices should use netif_receive_skb() to avoid
the overhead.
In the meantime someone added another variant, netif_rx_any_context(),
which behaves as suggested.
netif_rx() must be invoked with disabled bottom halves to ensure that
pending softirqs, which were raised within the function, are handled.
netif_rx_ni() can be invoked only from process context (bottom halves
must be enabled) because the function handles pending softirqs without
checking if bottom halves were disabled or not.
netif_rx_any_context() invokes on the former functions by checking
in_interrupts().
netif_rx() could be taught to handle both cases (disabled and enabled
bottom halves) by simply disabling bottom halves while invoking
netif_rx_internal(). The local_bh_enable() invocation will then invoke
pending softirqs only if the BH-disable counter drops to zero.
Eric is concerned about the overhead of BH-disable+enable especially in
regard to the loopback driver. As critical as this driver is, it will
receive a shortcut to avoid the additional overhead which is not needed.
Add a local_bh_disable() section in netif_rx() to ensure softirqs are
handled if needed.
Provide __netif_rx() which does not disable BH and has a lockdep assert
to ensure that interrupts are disabled. Use this shortcut in the
loopback driver and in drivers/net/*.c.
Make netif_rx_ni() and netif_rx_any_context() invoke netif_rx() so they
can be removed once they are no more users left.
Link: https://lkml.kernel.org/r/20100415.020246.218622820.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preempt_disable() () section was introduced in commit
cece1945bf ("net: disable preemption before call smp_processor_id()")
and adds it in case this function is invoked from preemtible context and
because get_cpu() later on as been added.
The get_cpu() usage was added in commit
b0e28f1eff ("net: netif_rx() must disable preemption")
because ip_dev_loopback_xmit() invoked netif_rx() with enabled preemption
causing a warning in smp_processor_id(). The function netif_rx() should
only be invoked from an interrupt context which implies disabled
preemption. The commit
e30b38c298 ("ip: Fix ip_dev_loopback_xmit()")
was addressing this and replaced netif_rx() with in netif_rx_ni() in
ip_dev_loopback_xmit().
Based on the discussion on the list, the former patch (b0e28f1eff)
should not have been applied only the latter (e30b38c298).
Remove get_cpu() and preempt_disable() since the function is supposed to
be invoked from context with stable per-CPU pointers. Bottom halves have
to be disabled at this point because the function may raise softirqs
which need to be processed.
Link: https://lkml.kernel.org/r/20100415.013347.98375530.davem@davemloft.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status of support for RDMA is currently being tracked with two
separate status flags. This is unnecessary with the current state of
the driver.
Simplify status tracking down to a single flag.
Rename the helper function to denote the RDMA specific status and
universally use the helper function to test the status bit.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes sense to have this in the common manager for debugging and
accounting of how much resources are used.
v2: cleanup kerneldoc a bit
v3: drop the atomic, update counter under lock instead
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com> (v1)
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Tested-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214093439.2989-2-christian.koenig@amd.com
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f87 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f87 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Foster says:
====================
use bulk reads for ocelot statistics
Ocelot loops over memory regions to gather stats on different ports.
These regions are mostly continuous, and are ordered. This patch set
uses that information to break the stats reads into regions that can get
read in bulk.
The motiviation is for general cleanup, but also for SPI. Performing two
back-to-back reads on a SPI bus require toggling the CS line, holding,
re-toggling the CS line, sending 3 address bytes, sending N padding
bytes, then actually performing the read. Bulk reads could reduce almost
all of that overhead, but require that the reads are performed via
regmap_bulk_read.
Verified with eth0 hooked up to the CPU port:
NIC statistics:
Good Rx Frames: 905
Rx Octets: 78848
Good Tx Frames: 691
Tx Octets: 52516
Rx + Tx 65-127 Octet Frames: 1574
Rx + Tx 128-255 Octet Frames: 22
Net Octets: 131364
Rx DMA chan 0: head_enqueue: 1
Rx DMA chan 0: tail_enqueue: 1032
Rx DMA chan 0: busy_dequeue: 628
Rx DMA chan 0: good_dequeue: 905
Tx DMA chan 0: head_enqueue: 346
Tx DMA chan 0: tail_enqueue: 345
Tx DMA chan 0: misqueued: 345
Tx DMA chan 0: empty_dequeue: 346
Tx DMA chan 0: good_dequeue: 691
p00_rx_octets: 52516
p00_rx_unicast: 691
p00_rx_frames_65_to_127_octets: 691
p00_tx_octets: 78848
p00_tx_unicast: 905
p00_tx_frames_65_to_127_octets: 883
p00_tx_frames_128_255_octets: 22
p00_tx_green_prio_0: 905
And with swp2 connected to swp3 with STP enabled:
NIC statistics:
tx_packets: 379
tx_bytes: 19708
rx_packets: 1
rx_bytes: 46
rx_octets: 64
rx_multicast: 1
rx_frames_below_65_octets: 1
rx_classified_drops: 1
tx_octets: 44630
tx_multicast: 387
tx_broadcast: 290
tx_frames_below_65_octets: 379
tx_frames_65_to_127_octets: 294
tx_frames_128_255_octets: 4
tx_green_prio_0: 298
tx_green_prio_7: 379
NIC statistics:
tx_packets: 1
tx_bytes: 52
rx_packets: 713
rx_bytes: 34148
rx_octets: 46982
rx_multicast: 407
rx_broadcast: 306
rx_frames_below_65_octets: 399
rx_frames_65_to_127_octets: 310
rx_frames_128_to_255_octets: 4
rx_classified_drops: 399
rx_green_prio_0: 314
tx_octets: 64
tx_multicast: 1
tx_frames_below_65_octets: 1
tx_green_prio_7: 1
v1 > v2: reword commit messages
v2 > v3: correctly mark this for net-next when sending
v3 > v4: calloc array instead of zalloc per review
v4 > v5:
Apply CR suggestions for whitespace
Fix calloc / zalloc mixup
Properly destroy workqueues
Add third commit to split long macros
v5 > v6:
Fix functionality - v5 was improperly tested
Add bugfix for ethtool mutex lock
Remove unnecessary ethtool stats reads
v6 > v7:
Remove mutex bug patch that was applied via net
Rename function based on CR
Add missed error check
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Create and utilize bulk regmap reads instead of single access for gathering
stats. The background reading of statistics happens frequently, and over
a few contiguous memory regions.
High speed PCIe buses and MMIO access will probably see negligible
performance increase. Lower speed buses like SPI and I2C could see
significant performance increase, since the bus configuration and register
access times account for a large percentage of data transfer time.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regmap supports bulk register reads. Ocelot does not. This patch adds
support for Ocelot to invoke bulk regmap reads. That will allow any driver
that performs consecutive reads over memory regions to optimize that
access.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ocelot.h file, several read / write macros were split across
multiple lines, while others weren't. Split all macros that exceed the 80
character column width and match the style of the rest of the file.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_update_stats function only needs to read from one port, yet it
was updating the stats for all ports. Update to only read the stats that
are necessary.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error is
printed.
Fixes warnings as:
msm_iommu 7500000.iommu: could not get smmu_pclk
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20220206202945.465195-1-david@ixit.cz
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It's been a long time since there was any reason to register IOMMU
drivers early. Convert to the standard platform driver helper.
CC: Andy Gross <agross@kernel.org>
CC: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/all/05ca5e1b29bdd350f4e20b9ceb031a2c281e23d2.1644005728.git.robin.murphy@arm.com/
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It's been a long time since there was any reason to register IOMMU
drivers early. Convert to the standard platform driver helper.
CC: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/c08d58bff340da6a829e76d66d2fa090a9718384.1644005728.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The vendor introduced an updated revision of IQS620A(T) silicon
which is backwards-compatible with previous revisions, the only
exception being the offset used to derive temperature.
Enable this new revision by returning the appropriate offset as
a function of the hardware number provided by the parent MFD.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Individual sub-devices may elect to make decisions based on the
specific revision of silicon encountered at probe. This data is
already read from the device, but is not retained.
Pass this data on to the sub-devices by adding the software and
hardware numbers (registers 0x01 and 0x02, respectively) to the
iqs62x_core struct.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The recently introduced coef_mutex for Realtek codec seems causing a
deadlock when the relevant code is invoked from the power-off state;
then the HD-audio core tries to power-up internally, and this kicks
off the codec runtime PM code that tries to take the same coef_mutex.
In order to avoid the deadlock, do the temporary power up/down around
the coef_mutex acquisition and release. This assures that the
power-up sequence runs before the mutex, hence no re-entrance will
happen.
Fixes: b837a9f5ab ("ALSA: hda: realtek: Fix race at concurrent COEF updates")
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220214132838.4db10fca@schienar
Link: https://lore.kernel.org/r/20220214130410.21230-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for R-Car Gen4 like r8a779f0 (R-Car S4-8). The IPMMU
hardware design of r8a779f0 is the same as r8a779a0. So, rename
"r8a779a0" to "rcar_gen4".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220208002030.1319984-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The default mixer resume code treats the errors at restoring the
modified mixer items as a fatal error, and it returns back to the
caller. This ends up in the resume failure, and the device will be
come unavailable, although basically those errors are intermittent and
can be safely ignored.
The problem itself has been present from the beginning, but it didn't
hit usually because the code tries to resume only the modified items.
But now with the recent commit to forcibly initialize each item at the
probe time, the problem surfaced more often, hence it appears as a
regression.
This patch fixes the regression simply by ignoring the errors at
resume.
Fixes: b96681bd58 ("ALSA: usb-audio: Initialize every feature unit once at probe time")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215561
Link: https://lore.kernel.org/r/20220214125711.20531-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All drivers using GPIOs as chip select have been rewritten to use
GPIO descriptors passing the ->use_gpio_descriptors flag. Retire
the code and fields used by the legacy GPIO API.
Do not drop the ->use_gpio_descriptors flag: it now only indicates
that we want to use GPIOs in addition to native chip selects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220210231954.807904-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang build fails with
spi-sunplus-sp7021.c:405:2: error: variable 'ret' is used
uninitialized whenever switch default is taken
default:
simplify code
Restore initializing ret. and add return error at default
Fixes: 47e8fe57a6 ("spi: Modify irq request position and modify parameters")
Reported-by: Tom Rix <trix@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Li-hao Kuo <lhjeff911@gmail.com>
Link: https://lore.kernel.org/r/7d91e6ce29f9a8df2c53a47b4b977664020e237a.1644805060.git.lhjeff911@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the driver is renamed (and moved) update the BIOS upgrade guide
accordingly from intel-spi to spi-intel. Keep the guide under MTD
documentation because this is pretty much still about MTD and SPI-NOR.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220209122706.42439-4-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The preferred way to implement SPI-NOR controller drivers is through SPI
subsubsystem utilizing the SPI MEM core functions. This converts the
Intel SPI flash controller driver over the SPI MEM by moving the driver
from SPI-NOR subsystem to SPI subsystem and in one go make it use the
SPI MEM functions. The driver name will be changed from intel-spi to
spi-intel to match the convention used in the SPI subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220209122706.42439-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver tries to disable the BIOS write protection
automatically even if this is not what the user wants. For this reason
modify the driver so that by default it does not touch the write
protection. Only if specifically asked by the user (setting writeable=1
command line parameter) the driver tries to disable the BIOS write
protection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220209122706.42439-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
