Even though the kernel's implementations of AES-XTS were updated to
implement ciphertext stealing and can operate on inputs of any size
larger than or equal to the AES block size, this feature is rarely used
in practice.
In fact, in the kernel, AES-XTS is only used to operate on 4096 or 512
byte blocks, which means that not only the ciphertext stealing is
effectively dead code, the logic in the bit sliced NEON implementation
to deal with fewer than 8 blocks at a time is also never used.
Since the bit-sliced NEON driver already depends on the plain NEON
version, which is slower but can operate on smaller data quantities more
straightforwardly, let's fallback to the plain NEON implementation of
XTS for any residual inputs that are not multiples of 128 bytes. This
allows us to remove a lot of complicated logic that rarely gets
exercised in practice.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of processing the entire input with the 8-way bit sliced
algorithm, which is sub-optimal for inputs that are not a multiple of
128 bytes in size, invoke the plain NEON version of CTR for the
remainder of the input after processing the bulk using 128 byte strides.
This allows us to greatly simplify the asm code that implements CTR, and
get rid of all the branches and special code paths. It also gains us a
couple of percent of performance.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of falling back to C code to deal with the final bit of input
that is not a round multiple of the block size, handle this in the asm
code, permitting us to use overlapping loads and stores for performance,
and implement the 16-byte wide XOR using a single NEON instruction.
Since NEON loads and stores have a natural width of 16 bytes, we need to
handle inputs of less than 16 bytes in a special way, but this rarely
occurs in practice so it does not impact performance. All other input
sizes can be consumed directly by the NEON asm code, although it should
be noted that the core AES transform can still only process 128 bytes (8
AES blocks) at a time.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of falling back to C code to do a memcpy of the output of the
last block, handle this in the asm code directly if possible, which is
the case if the entire input is longer than 16 bytes.
Cc: Nathan Huckleberry <nhuck@google.com>
Cc: Eric Biggers <ebiggers@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
LDWB is getting incorrectly used in HW when
CPT_AF_LF()_PTR_CTL[IQB_LDWB]=1 and CPT instruction queue has less than
320 free entries. So, increase HW instruction queue size by 320 and give
320 entries less for SW/NIX RX as a SW workaround.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When CPT_AF_DIAG[FLT_DIS] = 0 and a CPT engine access to
LLC/DRAM encounters a fault/poison, a rare case may result
in unpredictable data being delivered to a CPT engine.
So, this patch adds code to set FLT_DIS as a workaround.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When software sets CPT_AF_CTL[RNM_REQ_EN]=1 and RNM in not producing
entropy(i.e., RNM_ENTROPY_STATUS[NORMAL_CNT] < 0x40), the first cycle of
the response may be lost due to a conditional clocking issue. Due to
this, the subsequent random number stream will be corrupted. So, this
patch adds support to ensure RNM_ENTROPY_STATUS[NORMAL_CNT] = 0x40
before writing CPT_AF_CTL[RNM_REQ_EN] = 1, as a workaround.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Shijith Thotton <sthotton@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For two reasons, current_quality may become zero within the rngd
kernel thread: (1) The user lowers current_quality to 0 by writing
to the sysfs module parameter file (note that increasing the quality
from zero is without effect at the moment), or (2) there are two or
more hwrng devices registered, and those which provide quality>0 are
unregistered, but one with quality==0 remains.
If current_quality is 0, the randomness is not trusted and cannot help
to increase the entropy count. That will lead to continuous calls to
the hwrngd thread and continuous stirring of the input pool with
untrusted bits.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case the user-specified rng device is not working, it is not used;
therefore cur_rng_set_by_user must not be set to 1.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using rng_buffer in add_early_randomness() may race with rng_dev_read().
Use rng_fillbuf instead, as it is otherwise only used within the kernel
by hwrng_fillfn() and therefore never exposed to userspace.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to <linux/hw_random.h>, the @max parameter of the ->read
callback "is a multiple of 4 and >= 32 bytes". That promise was not
kept by add_early_randomness(), which only asked for 16 bytes. As
rng_buffer_size() is at least 32, we can simply ask for 32 bytes.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
hw-random device drivers depend on the hw-random core being
initialized. Make this ordering explicit, also for the case
these drivers are built-in. As the core itself depends on
misc_register() which is set up at subsys_initcall time,
advance the initialization of the core (only) to the
fs_initcall() level.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The soft dependency on cryptomgr is only needed in algapi because
if algapi isn't present then no algorithms can be loaded. This
also fixes the case where api is built-in but algapi is built as
a module as the soft dependency would otherwise get lost.
Fixes: 8ab23d547f ("crypto: api - Add softdep on cryptomgr")
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
syzbot found that mixing sendpage() and sendmsg(MSG_ZEROCOPY)
calls over the same TCP socket would again trigger the
infamous warning in inet_sock_destruct()
WARN_ON(sk_forward_alloc_get(sk));
While Talal took into account a mix of regular copied data
and MSG_ZEROCOPY one in the same skb, the sendpage() path
has been forgotten.
We want the charging to happen for sendpage(), because
pages could be coming from a pipe. What is missing is the
downgrading of pure zerocopy status to make sure
sk_forward_alloc will stay synced.
Add tcp_downgrade_zcopy_pure() helper so that we can
use it from the two callers.
Fixes: 9b65b17db7 ("net: avoid double accounting for pure zerocopy skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Talal Ahmad <talalahmad@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20220203225547.665114-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are cases where clang compiler is packaged in a way
readelf is a symbolic link to llvm-readelf. In such cases,
llvm-readelf will be used instead of default binutils readelf,
and the following error will appear during libbpf build:
Warning: Num of global symbols in
/home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/build/libbpf/sharedobjs/libbpf-in.o (367)
does NOT match with num of versioned symbols in
/home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/build/libbpf/libbpf.so libbpf.map (383).
Please make sure all LIBBPF_API symbols are versioned in libbpf.map.
--- /home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/build/libbpf/libbpf_global_syms.tmp ...
+++ /home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/build/libbpf/libbpf_versioned_syms.tmp ...
@@ -324,6 +324,22 @@
btf__str_by_offset
btf__type_by_id
btf__type_cnt
+LIBBPF_0.0.1
+LIBBPF_0.0.2
+LIBBPF_0.0.3
+LIBBPF_0.0.4
+LIBBPF_0.0.5
+LIBBPF_0.0.6
+LIBBPF_0.0.7
+LIBBPF_0.0.8
+LIBBPF_0.0.9
+LIBBPF_0.1.0
+LIBBPF_0.2.0
+LIBBPF_0.3.0
+LIBBPF_0.4.0
+LIBBPF_0.5.0
+LIBBPF_0.6.0
+LIBBPF_0.7.0
libbpf_attach_type_by_name
libbpf_find_kernel_btf
libbpf_find_vmlinux_btf_id
make[2]: *** [Makefile:184: check_abi] Error 1
make[1]: *** [Makefile:140: all] Error 2
The above failure is due to different printouts for some ABS
versioned symbols. For example, with the same libbpf.so,
$ /bin/readelf --dyn-syms --wide tools/lib/bpf/libbpf.so | grep "LIBBPF" | grep ABS
134: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LIBBPF_0.5.0
202: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LIBBPF_0.6.0
...
$ /opt/llvm/bin/readelf --dyn-syms --wide tools/lib/bpf/libbpf.so | grep "LIBBPF" | grep ABS
134: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LIBBPF_0.5.0@@LIBBPF_0.5.0
202: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LIBBPF_0.6.0@@LIBBPF_0.6.0
...
The binutils readelf doesn't print out the symbol LIBBPF_* version and llvm-readelf does.
Such a difference caused libbpf build failure with llvm-readelf.
The proposed fix filters out all ABS symbols as they are not part of the comparison.
This works for both binutils readelf and llvm-readelf.
Reported-by: Delyan Kratunov <delyank@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20220204214355.502108-1-yhs@fb.com
Some medium sized bugs in the various drivers. A couple are more recent
regressions:
- Fix two panics in hfi1 and two allocation problems
- Send the IGMP to the correct address in cma
- Squash a syzkaller bug related to races reading the multicast list
- Memory leak in siw and cm
- Fix a corner case spec compliance for HFI/QIB
- Correct the implementation of fences in siw
- Error unwind bug in mlx4
-----BEGIN PGP SIGNATURE-----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=RrpA
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Some medium sized bugs in the various drivers. A couple are more
recent regressions:
- Fix two panics in hfi1 and two allocation problems
- Send the IGMP to the correct address in cma
- Squash a syzkaller bug related to races reading the multicast list
- Memory leak in siw and cm
- Fix a corner case spec compliance for HFI/QIB
- Correct the implementation of fences in siw
- Error unwind bug in mlx4"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx4: Don't continue event handler after memory allocation failure
RDMA/siw: Fix broken RDMA Read Fence/Resume logic.
IB/rdmavt: Validate remote_addr during loopback atomic tests
IB/cm: Release previously acquired reference counter in the cm_id_priv
RDMA/siw: Fix refcounting leak in siw_create_qp()
RDMA/ucma: Protect mc during concurrent multicast leaves
RDMA/cma: Use correct address when leaving multicast group
IB/hfi1: Fix tstats alloc and dealloc
IB/hfi1: Fix AIP early init panic
IB/hfi1: Fix alloc failure with larger txqueuelen
IB/hfi1: Fix panic with larger ipoib send_queue_size
Add the thermal zones and thermistors used by the battery
charging code to the device tree so the charger code can look
up and poll the thermal zone for battery temperature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Seven fixes, six of which are fairly obvious driver fixes. The one
core change to the device budget depth is to try to ensure that if the
default depth is large (which can produce quite a sizeable bitmap
allocation per device), we give back the memory we don't need if
there's a queue size reduction in slave_configure (which happens to a
lot of devices).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYf2f4SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZ4GAP4zJbcN
BMXzp7x4kprqQieLgMLuqiZxeP8JKEsBCnKxEwD/eMpWUcI1zfYimvL6NM5A+r4J
0aYpPe4cGDhdthssOw8=
=rbtr
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes, six of which are fairly obvious driver fixes.
The one core change to the device budget depth is to try to ensure
that if the default depth is large (which can produce quite a sizeable
bitmap allocation per device), we give back the memory we don't need
if there's a queue size reduction in slave_configure (which happens to
a lot of devices)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: hisi_sas: Fix setting of hisi_sas_slot.is_internal
scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task
scsi: pm8001: Fix use-after-free for aborted TMF sas_task
scsi: pm8001: Fix warning for undescribed param in process_one_iomb()
scsi: core: Reallocate device's budget map on queue depth change
scsi: bnx2fc: Make bnx2fc_recv_frame() mp safe
scsi: pm80xx: Fix double completion for SATA devices
-----BEGIN PGP SIGNATURE-----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=4e8j
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Restructure j721e_pcie_probe() so we don't dereference a NULL pointer
(Bjorn Helgaas)
- Add a kirin_pcie_data struct to identify different Kirin variants to
fix probe failure for controllers with an internal PHY (Bjorn
Helgaas)
* tag 'pci-v5.17-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: kirin: Add dev struct for of_device_get_match_data()
PCI: j721e: Initialize pcie->cdns_pcie before using it
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Link: https://lore.kernel.org/r/11930209.O9o76ZdvQC@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add the new herobrine-r1. Note that this is pretty much a re-design
compared to herobrine-r0 so we don't attempt any dtsi to share stuff
between them.
This patch attempts to define things at 3 levels:
1. The Qcard level. Herobrine includes a Qcard PCB and the Qcard PCB
is supposed to be the same (modulo stuffing options) across
multiple boards, so trying to define what's there hopefully makes
sense. NOTE that newer "CRD" boards from Qualcomm also use
Qcard. When support for CRD3 is added hopefully it can use the
Qcard include (and perhaps we should even evaluate it using
herobrine.dtsi?)
2. The herobrine "baseboard" level. Right now most stuff is here with
the exception of things that we _know_ will be different per
board. We know that not all boards will have the same set of eMMC,
nvme, and SD. We also know that the exact pin names are likely to
be different.
3. The actual "board" level, AKA herobrine-rev1.
NOTES:
- This boots to command prompt. We're still waiting on the PWM driver.
- This assumes LTE for now. Once it's clear how WiFi-only SKUs will
work we expect some small changes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220204140550.v4.1.I5604b7af908e8bbe709ac037a6a8a6ba8a2bfa94@changeid
It's weird that there's a blank line between the two port nodes but
not between the attributes and the first port node. Add an extra blank
line to make it look right.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.11.Iecb7267402e697a5cfef4cd517116ea5b308ac9e@changeid
Pulls should be in the board files, not in the SoC dtsi
file. Remove. Even though the sc7280 boards don't currently refer to
dp_hot_plug_det, let's re-add the pulls there just to keep this as a
no-op change. If boards don't need this / don't want it later then we
can remove it from them.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.10.Id346b23642f91e16d68d75f44bcdb5b9fbd155ea@changeid
Pullups and drive strength don't belong in the SoC dtsi file. Move to
the board file.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.8.Iffff0c12440a047212a164601e637b03b9d2fc78@changeid
Like dp_out, we should have defined edp_out in sc7280.dtsi so we don't
need to do this in the board files.
Like dp_hot_plug_det, we should define edp_hot_plug_det in
sc7280.dtsi.
We should set the default pinctrl for edp_hot_plug_det in
sc7280.dtsi. NOTE: this is _unlike_ the dp_hot_plug_det. It is
reasonable that in some boards the dedicated DP Hot Plug Detect will
not be hooked up in favor of Type C mechanisms. This is unlike eDP
where the Hot Plug Detect line (which functions as "panel ready" in
eDP) is highly likely to be used by boards.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.7.Ic84bb69c45be2fccf50e3bd17b845fe20eec624c@changeid
Specifying "input-enable" on a MSM GPIO is a no-op for the most
part. The only thing it really does is to explicitly force the output
of a GPIO to be disabled right at the point of a pinctrl
transition. We don't need to do this and we don't typically specify
"input-enable" unless there's a good reason to. Remove it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.5.Ibaf8a803802beb089cc6266b37e6156cff3ddaec@changeid
This patch makes a few improvements to the way that sdc1 / sdc2
pinctrl is specified on sc7280:
1. There's no reason to "group" the sdc pins into one overarching node
and there's a downside: we have to replicate the hierarchy in the
board device tree files. Let's clean this up.
2. There's really not a lot of reason not to list the "pinctrl" for
sdc1 (eMMC) in the SoC dtsi file. These aren't GPIO pins and
everyone's going to specify the same pins.
3. Even though it's likely that boards will need to override pinctrl
for sdc2 (SD card) to add the card detect GPIO, we can be symmetric
and add it to the SoC dsti file.
4. Let's get rid of the word "on" from the normal config and add a
"sleep" suffix to the sleep config. This looks cleaner to me.
This is intended to be a no-op change but it could plausibly change
behavior depending on how the pinctrl code parses things. One thing to
note is that "SD card detect" is explicitly listed now as keeping its
pull enabled in sleep since we still want to detect card insertions
even if the controller is suspended (because no card is inserted). The
pinctrl framework likely did this anyway, but it's nice to see it
explicit.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.4.I79baad7f52351aafb470f8b21a9fa79d7031ad6a@changeid
The sdc1 / sdc2 pinctrl lines were randomly stuffed in the middle of
the qup pinctrl lines. Sort them properly. This is a no-op
change. Just code movement.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.3.I6ae594129a8ad3d18af9f5ebffd895b4f6353a0a@changeid
Some of the fixed regulators were missing the "-regulator" suffix. Add
it to be consistent within the file and consistent with the fixed
regulators in sc7180-trogdor.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.2.I627e60c5488d54a45fd1482ca19f0f6e45192db2@changeid
All of the other fixed regulators have the "-regulator" suffix. Add it
to pp3300_hub to match.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220202132301.v3.1.I7b284531f1c992932f7eef8abaf7cc5548064f33@changeid
This manifests as a crash early in boot on VexRiscv.
Signed-off-by: Myrtle Shah <gatecat@ds0.me>
[Palmer: split commit]
Fixes: 44c9225729 ("RISC-V: enable XIP")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This manifests as a crash early in boot on VexRiscv.
Signed-off-by: Myrtle Shah <gatecat@ds0.me>
[Palmer: split commit]
Fixes: 6d7f91d914 ("riscv: Get rid of CONFIG_PHYS_RAM_BASE in kernel physical address conversion")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Bean reported that a622435fbe ("PCI: kirin: Prefer
of_device_get_match_data()") broke kirin_pcie_probe() because it assumed
match data of 0 was a failure when in fact, it meant the match data was
"(void *)PCIE_KIRIN_INTERNAL_PHY".
Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL
and an "OF data missing" message.
Add a struct kirin_pcie_data to encode the PHY type. Then the result of
of_device_get_match_data() should always be a non-NULL pointer to a struct
kirin_pcie_data that contains the PHY type.
Fixes: a622435fbe ("PCI: kirin: Prefer of_device_get_match_data()")
Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas
Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com
Reported-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enable the audio, compute, sensor and modem remoteproc and specify
firmware path for these on the Qualcomm SM8450 QRD.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220128025513.97188-14-bjorn.andersson@linaro.org
The Qualcomm SM8450 carries the familiar set of audio, compute, sensor
and modem remoteprocs. Add these and their dependencies.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220128025513.97188-13-bjorn.andersson@linaro.org
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE8rQSAMVO+zA4DBdWxWXV+ddtWDsFAmH9eUcACgkQxWXV+ddt
WDvCvQ//bANu7air/Og5r2Mn0ZYyrcQl+yDYE75UC/tzTZNNtP8guwGllwlcsA0v
RQPiuFFtvjKMgKP6Eo1mVeUPkpX83VQkT+sqFRsFEFxazIXnSvEJ+iHVcuiZvgj1
VkTjdt7/mLb573zSA0MLhJqK1BBuFhUTCCHFHlCLoiYeekPAui1pbUC4LAE/+ksU
veCn9YS+NGkDpIv/b9mcALVBe+XkZlmw1LON8ArEbpY4ToafRk0qZfhV7CvyRbSP
Y1zLUScNLHGoR2WA1WhwlwuMePdhgX/8neGNiXsiw3WnmZhFoUVX7oUa6IWnKkKk
dD+x5Z3Z2xBQGK8djyqxzUFJ2VAvz15xGIM452ofGa1BJFZgV9hjPA6Y4RFdWx63
4AZ6OJwhrXhgMtWBhRtM6mGeje56ljwaxku9qhe585z8H5V8ezUNwWVkjY0bLKsd
iT3bUHEReoYRWuyszI1ZSm1DbyzNY2943ly97p/j8qKp4SHX39/QYAKmnuuHdIup
TnTBJOh38rj4S8BfF873aKAo7EfLJcDbTcZ1ivbuX5FeByRuQB4F0c1RRi4usMLc
DL5mhDhT71U1l/LF3IANQ4ieUfZbeFHd+dAVkYsGkYzzaWL8E03L582l/fqaVGsp
RaVpiuKnh2cyDXUxob8IYT5mZ/saa96xBSK8VEqnwjNEQCzKEeU=
=5MJl
-----END PGP SIGNATURE-----
Merge tag 'for-5.17-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few fixes and error handling improvements:
- fix deadlock between quota disable and qgroup rescan worker
- fix use-after-free after failure to create a snapshot
- skip warning on unmount after log cleanup failure
- don't start transaction for scrub if the fs is mounted read-only
- tree checker verifies item sizes"
* tag 'for-5.17-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: skip reserved bytes warning on unmount after log cleanup failure
btrfs: fix use of uninitialized variable at rm device ioctl
btrfs: fix use-after-free after failure to create a snapshot
btrfs: tree-checker: check item_size for dev_item
btrfs: tree-checker: check item_size for inode_item
btrfs: fix deadlock between quota disable and qgroup rescan worker
btrfs: don't start transaction for scrub if the fs is mounted read-only
Since commit e2bcbd7769 ("tools headers UAPI: remove stale lirc.h"),
the build of the selftests fails on rhel 8 since its version of
/usr/include/linux/lirc.h has no definition of RC_PROTO_RCMM32, etc [1].
[1] https://lkml.org/lkml/2022/1/28/275
Fixes: e2bcbd7769 ("tools headers UAPI: remove stale lirc.h")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
- fix fsdax partition offset misbehavior;
- clean up z_erofs_decompressqueue_work() declaration;
- fix up EOF lcluster inlining, especially for small compressed data.
-----BEGIN PGP SIGNATURE-----
iIcEABYIAC8WIQThPAmQN9sSA0DVxtI5NzHcH7XmBAUCYf0fBhEceGlhbmdAa2Vy
bmVsLm9yZwAKCRA5NzHcH7XmBCuaAP9GtcEDQ38ozhTgiD7ae8mPX808my3WDs+0
lyySofcEeAD+IxKNv0Gx7j7TgeaFWQZc7r16JeOPI9TKAe4BZaa1Tg0=
=J/Hq
-----END PGP SIGNATURE-----
Merge tag 'erofs-for-5.17-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Two fixes related to fsdax cleanup in this cycle and ztailpacking to
fix small compressed data inlining. There is also a trivial cleanup to
rearrange code for better reading.
Summary:
- fix fsdax partition offset misbehavior
- clean up z_erofs_decompressqueue_work() declaration
- fix up EOF lcluster inlining, especially for small compressed data"
* tag 'erofs-for-5.17-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix small compressed files inlining
erofs: avoid unnecessary z_erofs_decompressqueue_work() declaration
erofs: fix fsdax partition offset handling
These are some trivial fixups, which were needed to build the tests with
clang and -Werror. The following issues are fixed:
- Remove various unused variables.
- In child_poll_leader_exit_test, clang isn't smart enough to realize
syscall(SYS_exit, 0) won't return, so it complains we never return
from a non-void function. Add an extra exit(0) to appease it.
- In test_pidfd_poll_leader_exit, ret may be branched on despite being
uninitialized, if we have !use_waitpid. Initialize it to zero to get
the right behavior in that case.
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When running the pidfd_fdinfo_test on arm64, it fails for me. After some
digging, the reason is that the child exits due to SIGBUS, because it
overflows the 1024 byte stack we've reserved for it.
To fix the issue, increase the stack size to 8192 bytes (this number is
somewhat arbitrary, and was arrived at through experimentation -- I kept
doubling until the failure no longer occurred).
Also, let's make the issue easier to debug. wait_for_pid() returns an
ambiguous value: it may return -1 in all of these cases:
1. waitpid() itself returned -1
2. waitpid() returned success, but we found !WIFEXITED(status).
3. The child process exited, but it did so with a -1 exit code.
There's no way for the caller to tell the difference. So, at least log
which occurred, so the test runner can debug things.
While debugging this, I found that we had !WIFEXITED(), because the
child exited due to a signal. This seems like a reasonably common case,
so also print out whether or not we have WIFSIGNALED(), and the
associated WTERMSIG() (if any). This lets us see the SIGBUS I'm fixing
clearly when it occurs.
Finally, I'm suspicious of allocating the child's stack on our stack.
man clone(2) suggests that the correct way to do this is with mmap(),
and in particular by setting MAP_STACK. So, switch to doing it that way
instead.
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=iwuA
-----END PGP SIGNATURE-----
Merge tag 'block-5.17-2022-02-04' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request
- fix use-after-free in rdma and tcp controller reset (Sagi Grimberg)
- fix the state check in nvmf_ctlr_matches_baseopts (Uday Shankar)
- MD nowait null pointer fix (Song)
- blk-integrity seed advance fix (Martin)
- Fix a dio regression in this merge window (Ilya)
* tag 'block-5.17-2022-02-04' of git://git.kernel.dk/linux-block:
block: bio-integrity: Advance seed correctly for larger interval sizes
nvme-fabrics: fix state check in nvmf_ctlr_matches_baseopts()
md: fix NULL pointer deref with nowait but no mddev->queue
block: fix DIO handling regressions in blkdev_read_iter()
nvme-rdma: fix possible use-after-free in transport error_recovery work
nvme-tcp: fix possible use-after-free in transport error_recovery work
nvme: fix a possible use-after-free in controller reset during load
* Sergey volunteered to be a reviewer for the Renesas R-Car SATA
driver and PATA drivers. Update the MAINTAINERS file accordingly.
* Regression fix: add a horkage flag to prevent accessing the log
directory log page with SATADOM-ML 3ME SATA devices as they react
badly to reading that log page (from Anton).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCYfzmVgAKCRDdoc3SxdoY
dpYQAQD21wEYMv1/OuaY7/xRxfYJLpe67L3g2/qHNwhx1PDYlwEA2LSmlQsMXQBp
wgANq6sZdD4w9AyQHKt+yv4Oi41T3wA=
=O6iX
-----END PGP SIGNATURE-----
Merge tag 'ata-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
- Sergey volunteered to be a reviewer for the Renesas R-Car SATA driver
and PATA drivers. Update the MAINTAINERS file accordingly.
- Regression fix: add a horkage flag to prevent accessing the log
directory log page with SATADOM-ML 3ME SATA devices as they react
badly to reading that log page (from Anton).
* tag 'ata-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: Introduce ATA_HORKAGE_NO_LOG_DIR horkage
MAINTAINERS: add myself as Renesas R-Car SATA driver reviewer
MAINTAINERS: add myself as PATA drivers reviewer
Including:
- Warning fixes and a fix for a potential use-after-free in
IOMMU core code
- Another potential memory leak fix for the Intel VT-d driver
- Fix for an IO polling loop timeout issue in the AMD IOMMU
driver
-----BEGIN PGP SIGNATURE-----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=rcwP
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Warning fixes and a fix for a potential use-after-free in IOMMU core
code
- Another potential memory leak fix for the Intel VT-d driver
- Fix for an IO polling loop timeout issue in the AMD IOMMU driver
* tag 'iommu-fixes-v5.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix loop timeout issue in iommu_ga_log_enable()
iommu/vt-d: Fix potential memory leak in intel_setup_irq_remapping()
iommu: Fix some W=1 warnings
iommu: Fix potential use-after-free during probe
Pull random number generator fixes from Jason Donenfeld:
"For this week, we have:
- A fix to make more frequent use of hwgenerator randomness, from
Dominik.
- More cleanups to the boot initialization sequence, from Dominik.
- A fix for an old shortcoming with the ZAP ioctl, from me.
- A workaround for a still unfixed Clang CFI/FullLTO compiler bug,
from me. On one hand, it's a bummer to commit workarounds for
experimental compiler features that have bugs. But on the other, I
think this actually improves the code somewhat, independent of the
bug. So a win-win"
* tag 'random-5.17-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: only call crng_finalize_init() for primary_crng
random: access primary_pool directly rather than through pointer
random: wake up /dev/random writers after zap
random: continually use hwgenerator randomness
lib/crypto: blake2s: avoid indirect calls to compression function for Clang CFI
Fix compilation in the case when ACPI is selected and CRC32, depended
on by ACPI after recent changes, is not (Randy Dunlap).
-----BEGIN PGP SIGNATURE-----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=2rP4
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix compilation in the case when ACPI is selected and CRC32, depended
on by ACPI after recent changes, is not (Randy Dunlap)"
* tag 'acpi-5.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: require CRC32 to build
Add several tests to check bpf_core_types_are_compat() functionality:
- candidate type name exists and types match
- candidate type name exists but types don't match
- nested func protos at kernel recursion limit
- nested func protos above kernel recursion limit. Such bpf prog
is rejected during the load.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20220204005519.60361-3-mcroce@linux.microsoft.com
