In exististing implimentation, in min_loaded_core() for low_power
vpp frequency value is considering as vpp_freq instead of low_power_freq.
Fixed this by correcting vpp frequency calculation for encoder.
Fixes: 3cfe5815ce (media: venus: Enable low power setting for encoder)
Signed-off-by: Mansur Alisha Shaik <mansur@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow the LPID bit width and partition table size to be set at runtime
from the device tree.
Move the PID bit width detection into the same place.
KVM does not support using the extra bits yet, this is mainly required
to get the PTCR register values correct (so KVM will run but it will
not allocate > 4096 LPIDs).
OPAL firmware provides this property for POWER10 CPUs since skiboot
commit 9b85f7d961f2 ("hdata: add mmu-pid-bits and mmu-lpid-bits for
POWER10 CPUs").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211129030915.1888332-1-npiggin@gmail.com
V4L2_PIX_FMT_HM12 was redefined to V4L2_PIX_FMT_NV12_16L16, so use the
new name in libv4l-introduction.rst.
This fixes this warning:
libv4l-introduction.rst:27: WARNING: undefined label: v4l2-pix-fmt-hm12
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add missing documentation for two field. This fixes these kernel-doc
warnings:
drivers/media/platform/omap3isp/omap3isp.h:107: warning: Function parameter or member 'vp_clk_pol' not described in 'isp_ccp2_cfg'
drivers/media/platform/omap3isp/omap3isp.h:107: warning: Function parameter or member 'lanecfg' not described in 'isp_ccp2_cfg'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
smatch warns about data->list not being removed from list:
drivers/media/cec/core/cec-adap.c:926 cec_transmit_msg_fh() warn: '&data->list' not removed from list
It is a false warning, but it doesn't hurt to make the code more robust
and safely unhook data->list and data->xfer_list together with a WARN_ON
if this is actually ever needed (this really shouldn't happen).
Note that fixing the data->list warning just replaced it with a new similar
warning for data->xfer_list, so both needed to be addressed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stop the CODA960 JPEG encoder from overflowing capture buffers.
The bitstream buffer overflow interrupt doesn't seem to be connected,
so this has to be handled via timeout instead.
Reported-by: Martin Weber <martin.weber@br-automation.com>
Fixes: 96f6f62c46 ("media: coda: jpeg: add CODA960 JPEG encoder support")
Tested-by: Martin Weber <martin.weber@br-automation.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The JPEG encoder found in the Hantro H1 encoder block only produces a
raw entropy-encoded scan. The driver is responsible for building a JPEG
compliant bitstream and placing the entropy-encoded scan in it. Right
now the driver uses a bounce buffer for the hardware to output the raw
scan to.
In commit e765dba11e ("hantro: Move hantro_enc_buf_finish to JPEG
codec_ops.done"), the code that copies the raw scan from the bounce
buffer to the capture buffer was moved, but was only hooked up for the
Hantro H1 (then RK3288) variant. The RK3399 variant was broken,
producing a JPEG bitstream without the scan, and the capture buffer's
.bytesused field unset.
Fix this by duplicating the code that is executed when the JPEG encoder
finishes encoding a frame. As the encoded length is read back from
hardware, and the variants having different register layouts, the
code is duplicated rather than shared.
Fixes: e765dba11e ("hantro: Move hantro_enc_buf_finish to JPEG codec_ops.done")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The function mtk_venc_get_q_data always returns a reference
so there is no need to check if the return value is null.
In addition move the q_data initialization to the declaration
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The function vidioc_try_fmt has a big 'if-else' for
the capture and output cases. There is hardly any code
outside of that condition. It is therefore better to split
that functions into two different functions, one for each case.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mtk-vcodec uses some internal defined debug formats for
printing. This patch fixes some things in those defines:
1. use the 'pr_fmt' define to print function name and line.
2. remove 'if(DEBUG)' condition for the defines. This condition
prevents the debugs from being shown in case of dynamic debugs.
Instead replace 'pr_info' with 'pr_debug'
3. remove module parameters that enable/disable debug.
There is no reason for the driver to have those params. Having
those params require the user to explicitly set them when user
wants to see debug prints instead of using the global debugs
setting as expected by drivers to conform.
In addition to that, fix some warnings about debug formatting
[hverkuil: used %zu instead of %lu for sizeof() arguments]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix following boolreturn.cocci warning:
./drivers/staging/media/imx/imx-media-csi.c:153:9-10: WARNING:
return of 0/1 in function 'requires_passthrough' with return
type bool.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Register misc device in the end of driver's probing since device should
become visible to userspace once driver is fully prepared. Do the opposite
in case of driver removal. This is a minor improvement that doesn't solve
any problem, but makes code more consistent.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Entries in the reference picture list are marked as invalid by setting
the frame ID to 0x3f.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now when ARM architecture code also provides standard PCI core function
pci_remap_iospace(), use its devm_pci_remap_iospace() variant in
pci-mvebu.c driver instead of old ARM-specific pci_ioremap_io() function.
Call devm_pci_remap_iospace() before adding IO resource to host bridge
structure, at the place where it should be.
Link: https://lore.kernel.org/r/20211124154116.916-3-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci_remap_iospace() is standard PCI core function. Architecture code can
reimplement default core implementation if needs custom arch specific
functionality.
ARM needs custom implementation due to pci_ioremap_set_mem_type() hook
which allows ARM platforms to change mem type for iospace.
Implement this pci_remap_iospace() function for ARM architecture to
correctly handle pci_ioremap_set_mem_type() hook, which allows usage of
this standard PCI core function also for platforms which needs different
mem type (e.g. Marvell Armada 375, 38x and 39x).
Link: https://lore.kernel.org/r/20211124154116.916-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tegra114 and Tegra124 support reference picture marking, which will
cause BSEV to write picture marking data to SDRAM. Make sure there is
a valid destination address for that data to avoid error messages from
the memory controller.
[digetx@gmail.com: added BO support and moved secure BO allocation to kernel]
Tested-by: Anton Bambura <jenneron@protonmail.com> # T114 ASUS TF701T
Signed-off-by: Thierry Reding <treding@nvidia.com>
Co-developed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On a system with multiple encoders present, it's possible for two
encoders to write to the global luma and chroma quantization tables at
the same time if they both submit a JPEG frame to be encoded. Avoid
this race by moving the tables into the `jpeg_ctx` structure which is
stored on the stack.
Signed-off-by: James Cowgill <james.cowgill@blaize.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case of error the 'media_device_init()' call is not balanced by a
corresponding 'media_device_cleanup()' call.
Add it, when needed, as already done in the remove function.
Fixes: 118add98f8 ("media: mtk-vcodec: vdec: add media device if using stateless api")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
get_vaddr_frames() first calls pin_user_pages_fast() and if
that fails tries follow_pfn(). But if that also fails, then
the error code from pin_user_pages_fast() is overwritten with
the error code from follow_pfn().
Specifically if pin_user_pages_fast() returns -ENOMEM, then
follow_pfn() will overwrite that with -EINVAL, which is very
confusing.
So store the error code from pin_user_pages_fast() and return
that if follow_pfn() returns -EINVAL. -EINVAL indicates that
the page is unsuitable for follow_pfn, so pin_user_pages_fast()
was the correct call to make, and that error code should be
returned instead.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A driver with a remove callback that just returns 0 behaves identically
to a driver with no remove callback at all. So simplify accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the function fdp1_probe(), when get irq failed, the
function platform_get_irq() log an error message, so
remove redundant message here. And the variable type
of "ret" is int, the "fdp1->irq" is unsigned int, when
irq failed, this place maybe wrong, thus fix it.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the error handling of s3c_camif_probe, s3c_camif_unregister_subdev
may be executed twice, one is from camif_unregister_media_entities.
Although there is sanity check about the registration status,
it is not good to call s3c_camif_unregister_subdev twice in the error
handling code.
Fix this by moving s3c_camif_unregister_subdev out of
camif_unregister_media_entities, and add a s3c_camif_unregister_subdev
in the s3c_camif_remove.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the error handling code of bdisp_probe, it fails to invoke
pm_runtime_disable in many error sites.
Fix this by adding pm_runtime_disable at the label err_remove.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In the error handling code of hva_hw_probe, it fails to invoke
pm_runtime_disable in many error sites.
Fix this by adding a label err_disable with pm_runtime_disable and
adjust one goto from label err_clk to err_disable.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CAPTURE buffers might be read by the hardware after they are dequeued,
which goes against the general idea that userspace has full control over
dequeued buffers. Explain why and document the restrictions that this
implies for userspace.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of rkvdec_m2m_ops is to pass its address to v4l2_m2m_init(),
which takes a pointer to const v4l2_m2m_ops as argument. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of m2m_ops is to pass its address to v4l2_m2m_init(),
which takes a pointer to const v4l2_m2m_ops as argument. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PXP allows clockwise rotation of 0°, 90°, 180° and 270°.
Add support for it.
Tested on a imx6ull-evk.
For example, to rotate 90° the following Gstreamer pipeline can
be used:
gst-launch-1.0 videotestsrc ! video/x-raw,width=640,height=480 ! \
v4l2convert extra-controls=cid,rotate=90 ! \
video/x-raw,width=120,height=160 ! fbdevsink
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After devm_request_threaded_irq() is called there is a chance that an
interrupt may occur before the spinlock is initialized, which will trigger
a kernel oops.
To prevent that, move the initialization of the spinlock prior to
requesting the interrupts.
Fixes: 51abcf7fdb ("media: imx-pxp: add i.MX Pixel Pipeline driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PHTW register is selected based on default bit rate from Table[1].
for the bit rates less than or equal to 250. Currently first
value of default bit rate which is greater than or equal to
the caculated mbps is selected. This selection can be further
improved by selecting the default bit rate which is nearest to
the calculated value.
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.12]
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a warning message when the selected PHY speed is less
than supported minimum PHY speed given in the hsfreq table[1].
For raspberry pi camera capture on Kingfisher board with resolution
640x480, the calculated PHY speed is 48 mbps which is less than
the minimum PHY speed 80 Mbps from the table[1]. But in this cases
capture is successful.
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.
For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
This hsfreqrange is out of range.
The logic is changed to get the default value which is closest to the
calculated value [1]
Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Please note that According to Renesas in Table 25.9 the range for
220 default value is corrected as below
|Range (Mbps) | Default Bit rate (Mbps) |
-----------------------------------------------
| 197.125-244.125 | 220 |
-----------------------------------------------
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Kazuyoshi Akiyama <akiyama@nds-osk.co.jp>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PM8226 (used in MSM8226) has v1 smbb hardware and works fine with the
current driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The charger in PM8226 (used in MSM8226) is similar to the charger in
PM8941.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link drm_fb_cma_helper.o into drm_cma_helper.ko if CONFIG_DRM_KMS_HELPER
has been set. Remove CONFIG_DRM_KMS_CMA_HELPER config option. Selecting
KMS helpers and CMA will now automatically enable CMA KMS helpers.
Some drivers' Kconfig files did not correctly select KMS or CMA helpers.
Fix this as part of the change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-3-tzimmermann@suse.de
The MIPI DBI helpers access struct drm_gem_cma_object.vaddr in a
few places. Replace all instances with the correct generic GEM
functions. Use drm_gem_fb_vmap() for mapping a framebuffer's GEM
objects and drm_gem_fb_vunmap() for unmapping them. This removes
the dependency on CMA helpers within MIPI DBI.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-2-tzimmermann@suse.de
Convert the Renesas JPEG Processing Unit Device Tree binding
documentation to json-schema.
Document missing properties.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement fwnode parsing at probe time.
Check if the bus and number of lanes are supported.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify probe function by adding a local variable dev instead of using
&client->dev all the time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ACPI _HID INT347A represents the OV8865 sensor, the driver for which can
support the platforms that the cio2-bridge serves. Add it to the array
of supported sensors so the bridge will connect the sensor to the CIO2
device.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum gain figure in the v4l2 ctrl is wrong. The field is 12 bits
wide, which is where the 8191 figure comes from, but the datasheet is
specific that maximum gain is 16x (the low seven bits are fractional, so
16x gain is 2048)
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a chance that regulator_get() returns -EPROBE_DEFER, in which
case printing an error message is undesirable. To avoid spurious messages
in dmesg in the event that -EPROBE_DEFER is returned, use dev_err_probe()
on error paths for regulator_get().
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control
as 1/16th of a line. This is what the sensor expects, but isn't very
intuitive. Switch the control to be in units of a line and simply do the
16x multiplication before passing the value to the sensor.
The datasheet for this sensor gives minimum exposure as 2 lines, so take
the opportunity to correct the lower bounds of the control.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
