If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-6-maxime@cerno.tech
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Since we also want to change the HSM clock rate and it's only valid
while the clock is disabled, we need to move the clk_set_min_rate() call
on the HSM clock above pm_runtime_get_and_sync().
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-5-maxime@cerno.tech
Link: https://lore.kernel.org/linux-arm-kernel/20210924152334.1342630-1-maxime@cerno.tech/
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-4-maxime@cerno.tech
The driver, once it found a divider, tries to round it up by increasing
the least significant bit of the fractional part by one when the
round_up argument is set and there's a remainder.
However, since it increases the divider it will actually reduce the
clock rate below what we were asking for, leading to issues with
clk_set_min_rate() that will complain that our rounded clock rate is
below the minimum of the rate.
Since the dividers are fairly precise already, let's remove that part so
that we can have clk_set_min_rate() working.
This is effectively a revert of 9c95b32ca0 ("clk: bcm2835: add a round
up ability to the clock divisor").
Fixes: 9c95b32ca0 ("clk: bcm2835: add a round up ability to the clock divisor")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-3-maxime@cerno.tech
The driver currently tries to pick the closest rate that is lower than
the rate being requested.
This causes an issue with clk_set_min_rate() since it actively checks
for the rounded rate to be above the minimum that was just set.
Let's change the logic a bit to pick the closest rate to the requested
rate, no matter if it's actually higher or lower.
Fixes: 6d18b8adbe ("clk: bcm2835: Support for clock parent selection")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org> # boot and basic functionality
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-2-maxime@cerno.tech
This change fix the TX ack mechanism in various ways:
- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.
- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.
- This adds a sanity (paranoia?) check on the skb tx ack pointer.
- Resume TX queue if TX status tagged packet TX fails.
Cc: stable@vger.kernel.org
Fixes: fdf21cc371 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org
We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.
After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.
Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.
Cc: stable@vger.kernel.org
Fixes: 512b191d96 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: 6cd536fe62 ("cfg80211: change internal management frame registration API")
Link: https://lore.kernel.org/r/20211025133111.5cf733eab0f4.I7b0abb0494ab712f74e2efcd24bb31ac33f7eee9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Third set of patches for v5.16. This time we have a small one to
quickly fix two mt76 build failures I had missed in my previous pull
request.
Major changes:
mt76
* fix linking when CONFIG_MMC is disabled
* fix dev_err() format warning
* mt7615: mt7622: fix ibss and meshpoint
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmF2biAVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622b50gH/2ZQ5PVfP1JiE/PprBnISRhHSTjx
N0mirZfdeEfAATYgWRcFZZvZsidNH44s8M3mbQrLzPM3zAqx9qPHZHH1Gxr8OX9a
9RHAra60uNT1lNc/vLluNsE+uICfnHRyI3BPxqL8OK62wf5jlSaYtYlfIrOW3W5j
MyVjk9Acn2dQAhhYDLqfMru/w9k+xk10Omj072XOYImby2TGmF1b/SHBsmTLNW5l
zkjLGDrRU7LIx43LQy2ZZ0NUyYM0wNvSKAZS5QUGC+jbwG7iha+W7RwZ6P5ayMNc
5pPN2Ehz0qAd0p4JNZWPck1uC40A5qhDAD69L14MU42Pl4K88IAbNZjdE9o=
=grVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Third set of patches for v5.16. This time we have a small one to
quickly fix two mt76 build failures I had missed in my previous pull
request.
Major changes:
mt76
* fix linking when CONFIG_MMC is disabled
* fix dev_err() format warning
* mt7615: mt7622: fix ibss and meshpoint
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeroen de Borst says:
====================
gve: Add jumbo-frame support for GQ
This patchset introduces jumbo-frame support for the GQ queue format.
The device already supports jumbo-frames on TX. This introduces
multi-descriptor RX packets using a packet continuation bit.
A widely deployed driver has a bug with causes it to fail to load
when a MTU greater than 2048 bytes is configured. A jumbo-frame device
option is introduced to pass a jumbo-frame MTU only to drivers that
support it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A widely deployed driver has a bug that will cause the driver not
to load when a max_mtu > 2048 is present in the device descriptor.
To avoid this bug while still enabling jumbo frames, we present a lower
max_mtu in the device descriptor and pass the actual max_mtu in
a separate device option.
The driver supports 2 different queue formats. To enable features
on one queue format, but not the other, a supported_features mask
was added to the device options in the device descriptor.
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to receive RX packets spread across multiple
buffers:
For a given multi-fragment packet the "packet continuation" bit is set
on all descriptors except the last one. These descriptors' payloads are
combined into a single SKB before the SKB is handed to the
networking stack.
This change adds a "packet buffer size" notion for RX queues. The
CreateRxQueue AdminQueue command sent to the device now includes the
packet_buffer_size.
We opt for a packet_buffer_size of PAGE_SIZE / 2 to give the
driver the opportunity to flip pages where we can instead of copying.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactor moves the skb_head and skb_tail fields into a new
gve_rx_ctx struct. This new struct will contain information about the
current packet being processed. This is in preparation for
multi-descriptor RX packets.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kvm_vcpu_block, the current task is set to TASK_INTERRUPTIBLE before
making a final check whether the vCPU should be woken from HLT by any
incoming interrupt.
This is a problem for the get_user() in __kvm_xen_has_interrupt(), which
really shouldn't be sleeping when the task state has already been set.
I think it's actually harmless as it would just manifest itself as a
spurious wakeup, but it's causing a debug warning:
[ 230.963649] do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000b6bcdbc9>] prepare_to_swait_exclusive+0x30/0x80
Fix the warning by turning it into an *explicit* spurious wakeup. When
invoked with !task_is_running(current) (and we might as well add
in_atomic() there while we're at it), just return 1 to indicate that
an IRQ is pending, which will cause a wakeup and then something will
call it again in a context that *can* sleep so it can fault the page
back in.
Cc: stable@vger.kernel.org
Fixes: 40da8ccd72 ("KVM: x86/xen: Add event channel interrupt vector upcall")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <168bf8c689561da904e48e2ff5ae4713eaef9e2d.camel@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Ido Schimmel says:
====================
selftests: mlxsw: Various updates
This patchset contains various updates to mlxsw selftests.
Patch #1 replaces open-coded compatibility checks with dedicated
helpers. These helpers are used to skip tests when run on incompatible
machines.
Patch #2 avoids spurious failures in some tests by using permanent
neighbours instead of reachable ones.
Patch #3 reduces the run time of a test by not iterating over all the
available trap policers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating over all the available trap policers, only perform
the tests with three policers: The first, the last and the one in the
middle of the range. On a Spectrum-3 system, this reduces the run time
from almost an hour to a few minutes.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop objects tests configure dummy reachable neighbours so that
the nexthops will have a MAC address and be programmed to the device.
Since these are dummy reachable neighbours, they can be transitioned by
the kernel to a failed state if they are around for too long. This can
happen, for example, if the "TIMEOUT" variable is configured with a too
high value.
Make the tests more robust by configuring the neighbours as permanent,
so that the tests do not depend on the configured timeout value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.
Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:
mlxsw_only_on_spectrum 2+ || return
Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two bugs that might result in CPUs not woken up when interrupts are
pending.
-----BEGIN PGP SIGNATURE-----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=TjUB
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-master-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes for interrupt delivery
Two bugs that might result in CPUs not woken up when interrupts are
pending.
The entry "brcm,bcm4330-bt" was listed twice in the table.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andrew Lunn says:
====================
ksettings_{get|set} lock fixes
Walter Stoll <Walter.Stoll@duagon.com> reported a race condition
between "ethtool -s eth0 speed 100 duplex full autoneg off" and phylib
reading the current status from the PHY. Both ksetting_get and
ksetting_set fail the take the phydev mutex, and as a result, there is
a small window of time where the phydev members are not self
consistent.
Patch 1 fixes phy_ethtool_ksettings_get by adding the needed lock.
Patches 2 and 3 move code around and perform to refactoring, to allow
patch 4 to fix phy_ethtool_ksettings_set by added the lock.
Thanks go to Walter for the detailed origional report, suggested fix,
and testing of the proposed patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9af7c32cec ("ath10k: add target IRAM recovery feature support")
introduced a new firmware feature flag ATH10K_FW_FEATURE_IRAM_RECOVERY. But
this caused ath10k_pci module load to fail if ATH10K_FW_CRASH_DUMP_RAM_DATA bit
was not enabled in the ath10k coredump_mask module parameter:
[ 2209.328190] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 2209.434414] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 2209.547191] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.9.0.2-00099 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 cbade90a
[ 2210.896485] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 0:1 crc32 a040efc2
[ 2213.603339] ath10k_pci 0000:02:00.0: failed to copy target iram contents: -12
[ 2213.839027] ath10k_pci 0000:02:00.0: could not init core (-12)
[ 2213.933910] ath10k_pci 0000:02:00.0: could not probe fw (-12)
And by default coredump_mask does not have ATH10K_FW_CRASH_DUMP_RAM_DATA
enabled so anyone using a firmware with iram-recovery feature would fail. To my
knowledge only QCA9984 firmwares starting from release 10.4-3.9.0.2-00099
enabled the feature.
The reason for regression was that ath10k_core_copy_target_iram() used
ath10k_coredump_get_mem_layout() to get the memory layout, but when
ATH10K_FW_CRASH_DUMP_RAM_DATA was disabled it would get just NULL and bail out
with an error.
While looking at all this I noticed another bug: if CONFIG_DEV_COREDUMP is
disabled but the firmware has iram-recovery enabled the module load fails with
similar error messages. I fixed that by returning 0 from
ath10k_core_copy_target_iram() when _ath10k_coredump_get_mem_layout() returns
NULL.
Tested-on: QCA9984 hw2.0 PCI 10.4-3.9.0.2-00139
Fixes: 9af7c32cec ("ath10k: add target IRAM recovery feature support")
Signed-off-by: Abinaya Kalaiselvan <akalaise@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211020075054.23061-1-kvalo@codeaurora.org
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luo Jie says:
====================
net: phy: Add qca8081 ethernet phy driver
This patch series add the qca8081 ethernet phy driver support, which
improve the wol feature, leverage at803x phy driver and add the fast
retrain, master/slave seed and CDT feature.
Changes in v7:
* update Reviewed-by tags.
Changes in v6:
* add Reviewed-by tags on the applicable patches.
Changes in v5:
* rebase the patches on net-next/master.
Changes in v4:
* handle other interrupts in set_wol.
* add genphy_c45_fast_retrain.
Changes in v3:
* correct a typo "excpet".
* remove the suffix "PHY" from phy name.
Changes in v2:
* add definitions of fast retrain related registers in mdio.h.
* break up the patch into small patches.
* improve the at803x legacy code.
Changes in v1:
* merge qca8081 phy driver into at803x.
* add cdt feature.
* leverage at803x phy driver helpers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To perform CDT of qca8081 phy:
1. disable hibernation.
2. force phy working in MDI mode.
3. force phy working in 1000BASE-T mode.
4. configure the related thresholds.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. The master/slave seed needs to be updated when the link can't
be created.
2. The case where two qca8081 PHYs are connected each other and
master/slave seed is generated as the same value also needs
to be considered, so adding this code change into read_status
instead of link_change_notify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 phy is a single port phy, configure
phy the lower seed value to make it linked as slave
mode easier.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the qca8081 phy driver config_init function, which includes:
1. Enable fast restrain.
2. Add 802.3az configurations.
3. Initialize ADC threshold as 100mv.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the constants for 2.5G fast retrain capability
in 10G AN control register, fast retrain status and
control register and THP bypass register into mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse at803x phy driver config_aneg excepting
adding 2500M auto-negotiation.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the at803x phy driver get_features excepting
adding 2500M capability.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Separate the function at803x_read_specific_status from
the at803x_read_status, since it can be reused by the
read_status of qca8081 phy driver excepting adding the
2500M speed.
2. Add the qca8081 read_status function qca808x_read_status.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 is a single port ethernet phy chip that supports
10/100/1000/2500 Mbps mode.
Add the basic phy driver features, and reuse the at803x
phy driver functions.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GENMASK() for the current speed value.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol feature is controlled by the MMD3.8012 bit5,
need to set this bit when the wol function is enabled.
The reg18 bit0 is for enabling WOL interrupt, when wol
occurs, the wol interrupt status reg19 bit0 is set to 1.
Call phy_trigger_machine if there are any other interrupt
pending in the function set_wol.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert at803x_set_wol to use phy_modify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^
Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.
Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.
Fixes: e263bdab9c ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org
I got a kernel BUG report when doing fault injection test:
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:45!
...
RIP: 0010:__list_del_entry_valid.cold+0x12/0x4d
...
Call Trace:
proto_unregister+0x83/0x220
cmtp_cleanup_sockets+0x37/0x40 [cmtp]
cmtp_exit+0xe/0x1f [cmtp]
do_syscall_64+0x35/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns
success. This will cause a kernel bug when accessing uncreated ctmp
related data when the module exits.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Guangbin Huang says:
====================
net: hns3: updates for -next
This series includes some updates for the HNS3 ethernet driver.
for it.
off.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds himac error recovery module, link_error type and
ptp_error type for himac.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds one ras error of bus related for roce, this error
including RRESP/BRESP and read poison error.
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>