Commit graph

1,089,026 commits

Author SHA1 Message Date
Eddie James
6d8097e340 ARM: dts: aspeed: rainier: Remove gpio hog for GPIOP7
Only the pass 1 Ingraham board (Rainier system) had a micro-controller
wired to GPIOP7 on ball Y23. Pass 2 boards have this ball wired to the
heartbeat LED, so remove the hog as this device tree supports pass 2.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210915214738.34382-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:11 +10:30
Eddie James
64fc9a95b4 ARM: dts: aspeed: rainier: Add eeprom on bus 12
The devicetree was missing an eeprom.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210915214738.34382-4-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:10 +10:30
Andrew Jeffery
59618b1c3b ARM: dts: aspeed: p10bmc: Enable KCS channel 2
Rainier uses KCS channel 2 as the source for the debug-trigger
application outlined at [1] and implemented at [2].

[1] https://github.com/openbmc/docs/blob/master/designs/bmc-service-failure-debug-and-recovery.md
[2] https://github.com/openbmc/debug-trigger

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210623033854.587464-8-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:07 +10:30
Andrew Jeffery
d4efb68f17 ARM: dts: aspeed: p10bmc: Use KCS 3 for MCTP binding
The MCTP LPC driver was loaded by hacking up the compatible in the
devicetree node for KCS 4. With the introduction of the raw KCS driver
this hack is no-longer required. Use the regular compatible string for
KCS 4 and configure the appropriate SerIRQ.

The reset state of the status bits on KCS 4 is inappropriate for the
MCTP LPC binding. Switch to KCS 3 which has a different reset behaviour.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:03 +10:30
Lin.TommySC 林世欽 TAO
2561b4f6ec ARM: dts: aspeed: Adding Inventec Transformers BMC
Initial introduction of Inventec Transformers x86 family equipped with
AST2600 BMC SoC.

Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/7d7b20575f994a3c9018223a3c5f198d@inventec.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:03 +10:30
Eddie James
a559f27a40 ARM: dts: aspeed: everest: Fix bus 15 muxed eeproms
The eeproms on bus 15 muxes were at the wrong addresses.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-6-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:02 +10:30
Eddie James
e175be2a71 ARM: dts: aspeed: everest: Add IBM Operation Panel I2C device
Set I2C bus 14 to multi-master mode and add the panel device that will
register the I2C controller as a slave device.
In addition, in early Everest systems, the panel device was behind an
I2C switch, which doesn't work for slave mode. Get it working (albeit
unreliably, since a master transaction might switch the switch at any
moment) by defaulting the switch channel to the one with the panel.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:02 +10:30
Eddie James
e80e70fb05 ARM: dts: aspeed: everest: Add I2C switch on bus 8
The switch controls two busses containing some VRMs.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-4-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:02 +10:30
Eddie James
4df227c407 ARM: dts: aspeed: rainier and everest: Remove PCA gpio specification
Specifying gpio nodes under PCA led controllers no longer does anything,
so remove those nodes in the device trees.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:56:02 +10:30
Eddie James
bf1914e2cf ARM: dts: aspeed: p10bmc: Fix ADC iio-hwmon battery node name
In keeping with previous systems, call the iio-hwmon bridge node
"iio-hwmon-battery" to distinguish it as the battery voltage
sensor.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-10-21 16:55:58 +10:30
Leon Romanovsky
60dd57c747 Merge brank 'mlx5_mkey' into rdma.git for-next
A small series to clean up the mlx5 mkey code across the mlx5_core and
InfiniBand.

* branch 'mlx5_mkey':
  RDMA/mlx5: Attach ndescs to mlx5_ib_mkey
  RDMA/mlx5: Move struct mlx5_core_mkey to mlx5_ib
  RDMA/mlx5: Replace struct mlx5_core_mkey by u32 key
  RDMA/mlx5: Remove pd from struct mlx5_core_mkey
  RDMA/mlx5: Remove size from struct mlx5_core_mkey
  RDMA/mlx5: Remove iova from struct mlx5_core_mkey

  Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
2021-10-21 08:27:39 +03:00
Johnathon Clark
5fc462c3aa ALSA: hda/realtek: Fix mic mute LED for the HP Spectre x360 14
On the 'HP Spectre x360 Convertible 14-ea0xx' the microphone mute led is
controlled by GPIO 0x04. The speaker mute LED does not seem to be
exposed by GPIO and is there not set.

[ a slight coding-style fix by tiwai ]

Fixes: c3bb2b5219 ("ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup")
Signed-off-by: Johnathon Clark <john.clark@cantab.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211020131253.35894-1-john.clark@cantab.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-10-21 07:06:49 +02:00
Takashi Iwai
411cef6adf ALSA: mixer: oss: Fix racy access to slots
The OSS mixer can reassign the mapping slots dynamically via proc
file.  Although the addition and deletion of those slots are protected
by mixer->reg_mutex, the access to slots aren't, hence this may cause
UAF when the slots in use are deleted concurrently.

This patch applies the mixer->reg_mutex in all appropriate code paths
(i.e. the ioctl functions) that may access slots.

Reported-by: syzbot+9988f17cf72a1045a189@syzkaller.appspotmail.com
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000036adc005ceca9175@google.com
Link: https://lore.kernel.org/r/20211020164846.922-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-10-21 07:03:47 +02:00
Jiri Olsa
130c080658 tracing: Add trampoline/graph selftest
Adding selftest for checking that direct trampoline can
co-exist together with graph tracer on same function.

This is supported for CONFIG_HAVE_DYNAMIC_FTRACE_WITH_ARGS
config option, which is defined only for x86_64 for now.

Link: https://lkml.kernel.org/r/20211008091336.33616-5-jolsa@kernel.org

Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-20 23:44:44 -04:00
Steven Rostedt (VMware)
0c0593b45c x86/ftrace: Make function graph use ftrace directly
We don't need special hook for graph tracer entry point,
but instead we can use graph_ops::func function to install
the return_hooker.

This moves the graph tracing setup _before_ the direct
trampoline prepares the stack, so the return_hooker will
be called when the direct trampoline is finished.

This simplifies the code, because we don't need to take into
account the direct trampoline setup when preparing the graph
tracer hooker and we can allow function graph tracer on entries
registered with direct trampoline.

Link: https://lkml.kernel.org/r/20211008091336.33616-4-jolsa@kernel.org

[fixed compile error reported by kernel test robot <lkp@intel.com>]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-20 23:44:43 -04:00
Steven Rostedt (VMware)
4a30e4c930 ftrace/x86_64: Have function graph tracer depend on DYNAMIC_FTRACE
The function graph tracer is going to now depend on
ARCH_SUPPORTS_FTRACE_OPS, as that also means that it can support ftrace
args. Since ARCH_SUPPORTS_FTRACE_OPS depends on DYNAMIC_FTRACE, this
means that the function graph tracer for x86_64 will need to depend on
DYNAMIC_FTRACE.

Link: https://lkml.kernel.org/r/20211020233555.16b0dbf2@rorschach.local.home

Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2021-10-20 23:44:35 -04:00
James Smart
83c3a7beae scsi: lpfc: Update lpfc version to 14.0.0.3
Update lpfc version to 14.0.0.3.

Link: https://lore.kernel.org/r/20211020211417.88754-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:46 -04:00
James Smart
af984c8729 scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
A link bounce to a slow fabric may observe FDISC response delays lasting
longer than devloss tmo.  Current logic decrements the final fabric node
kref during a devloss tmo event.  This results in a NULL ptr dereference
crash if the FDISC completes for that fabric node after devloss tmo.

Fix by adding the NLP_IN_RECOV_POST_DEV_LOSS flag, which is set when
devloss tmo triggers and we've noticed that fabric node recovery has
already started or finished in between the time lpfc_dev_loss_tmo_callbk
queues lpfc_dev_loss_tmo_handler.  If fabric node recovery succeeds, then
the driver reverses the devloss tmo marked kref put with a kref get.  If
fabric node recovery fails, then the final kref put relies on the ELS
timing out or the REG_LOGIN cmpl routine.

Link: https://lore.kernel.org/r/20211020211417.88754-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:46 -04:00
James Smart
1854f53ccd scsi: lpfc: Fix link down processing to address NULL pointer dereference
If an FC link down transition while PLOGIs are outstanding to fabric well
known addresses, outstanding ABTS requests may result in a NULL pointer
dereference. Driver unload requests may hang with repeated "2878" log
messages.

The Link down processing results in ABTS requests for outstanding ELS
requests. The Abort WQEs are sent for the ELSs before the driver had set
the link state to down. Thus the driver is sending the Abort with the
expectation that an ABTS will be sent on the wire. The Abort request is
stalled waiting for the link to come up. In some conditions the driver may
auto-complete the ELSs thus if the link does come up, the Abort completions
may reference an invalid structure.

Fix by ensuring that Abort set the flag to avoid link traffic if issued due
to conditions where the link failed.

Link: https://lore.kernel.org/r/20211020211417.88754-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:46 -04:00
James Smart
15af02d8a5 scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
A remote nport can stop responding to PLOGI beyond the ELS I/O timeout
under some fault conditions.  When this happens, the non-response triggers
a dev_loss_tmo event from the transport which causes the driver to abort
the PLOGI and stop any retries. This was due to a policy in the ELS
completion handler whenever an ELS was terminated due to driver request.

Revise the ELS completion path to detect PLOGIs that were aborted and
allow retries.

Link: https://lore.kernel.org/r/20211020211417.88754-6-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:45 -04:00
James Smart
79b20becce scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
An error is detected with the following report when unloading the driver:
  "KASAN: use-after-free in lpfc_unreg_rpi+0x1b1b"

The NLP_REG_LOGIN_SEND nlp_flag is set in lpfc_reg_fab_ctrl_node(), but the
flag is not cleared upon completion of the login.

This allows a second call to lpfc_unreg_rpi() to proceed with nlp_rpi set
to LPFC_RPI_ALLOW_ERROR.  This results in a use after free access when used
as an rpi_ids array index.

Fix by clearing the NLP_REG_LOGIN_SEND nlp_flag in
lpfc_mbx_cmpl_fc_reg_login().

Link: https://lore.kernel.org/r/20211020211417.88754-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:45 -04:00
James Smart
7a1dda9436 scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
Applications determine loop support in part by querying the 'pls' sysfs
node. Reporting of 'pls' (Private Loop Support) is derived from the
descriptor returned by the COMMON_GET_SLI4_PARAMETERS mailbox command,
which is issued during initialization or after a reset.

The value of this field may change if there is a dynamic SFP change.  The
driver currently will not pick up the change as there was no reset
scenario.

Rework to commonize the sending of the COMMON_GET_SLI4_PARAMETERS
command. Add the calling of the routine after receipt of an async event
indicating an SFP change.

Link: https://lore.kernel.org/r/20211020211417.88754-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:45 -04:00
James Smart
d305c253af scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
A prior patch introduced HBA_NEEDS_CFG_PORT flag logic, but in
lpfc_sli_brdrestart_s3() code path, right after HBA_NEEDS_CFG_PORT is set,
the phba->hba_flag is cleared in lpfc_sli_brdreset().

Fix by calling lpfc_sli_chipset_init() to wait for successful restart of
the HBA in lpfc_host_reset_handler() after lpfc_sli_brdrestart().

lpfc_sli_chipset_init() sets the HBA_NEEDS_CFG_PORT flag so that the
lpfc_sli_hba_setup() routine from lpfc_online() will execute
lpfc_sli_config_port() initialization step when the brdrestart is
successful.

Link: https://lore.kernel.org/r/20211020211417.88754-3-jsmart2021@gmail.com
Fixes: d2f2547efd ("scsi: lpfc: Fix auto sli_mode and its effect on CONFIG_PORT for SLI3")
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:45 -04:00
James Smart
a516074c20 scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
In cases when lpfc_enable_pci_dev() fails, lpfc_printf_log() with
LOG_TRACE_EVENT set will call lpfc_dmp_dbg() which uses the
phba->port_list_lock.

However, phba->port_list_lock does not get initialized until
lpfc_setup_driver_resource_phase1().  Thus, any initialization routine with
LOG_TRACE_EVENT log message prior to lpfc_setup_driver_resource_phase1()
will crash.

Revert LOG_TRACE_EVENT back to LOG_INIT for all log messages in routines
prior to lpfc_setup_driver_resource_phase1().

Link: https://lore.kernel.org/r/20211020211417.88754-2-jsmart2021@gmail.com
CC: Zheyu Ma <zheyuma97@gmail.com>
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:33:45 -04:00
Chanho Park
282da7cef0 scsi: ufs: ufs-exynos: Correct timeout value setting registers
PA_PWRMODEUSERDATA0 -> DL_FC0PROTTIMEOUTVAL
PA_PWRMODEUSERDATA1 -> DL_TC0REPLAYTIMEOUTVAL
PA_PWRMODEUSERDATA2 -> DL_AFC0REQTIMEOUTVAL

Link: https://lore.kernel.org/r/20211018062841.18226-1-chanho61.park@samsung.com
Fixes: a967ddb22d ("scsi: ufs: ufs-exynos: Apply vendor-specific values for three timeouts")
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:25:51 -04:00
Srinivas Kandagatla
b6ca770ae7 scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
UFS drivers that probe defer will end up leaking memory allocated for clk
and regulator names via kstrdup() because the structure that is holding
this memory is allocated via devm_* variants which will be freed during
probe defer but the names are never freed.

Use same devm_* variant of kstrdup to free the memory allocated to name
when driver probe defers.

Kmemleak found around 11 leaks on Qualcomm Dragon Board RB5:

unreferenced object 0xffff66f243fb2c00 (size 128):
  comm "kworker/u16:0", pid 7, jiffies 4294893319 (age 94.848s)
  hex dump (first 32 bytes):
    63 6f 72 65 5f 63 6c 6b 00 76 69 72 74 75 61 6c  core_clk.virtual
    2f 77 6f 72 6b 71 75 65 75 65 2f 73 63 73 69 5f  /workqueue/scsi_
  backtrace:
    [<000000006f788cd1>] slab_post_alloc_hook+0x88/0x410
    [<00000000cfd1372b>] __kmalloc_track_caller+0x138/0x230
    [<00000000a92ab17b>] kstrdup+0xb0/0x110
    [<0000000037263ab6>] ufshcd_pltfrm_init+0x1a8/0x500
    [<00000000a20a5caa>] ufs_qcom_probe+0x20/0x58
    [<00000000a5e43067>] platform_probe+0x6c/0x118
    [<00000000ef686e3f>] really_probe+0xc4/0x330
    [<000000005b18792c>] __driver_probe_device+0x88/0x118
    [<00000000a5d295e8>] driver_probe_device+0x44/0x158
    [<000000007e83f58d>] __device_attach_driver+0xb4/0x128
    [<000000004bfa4470>] bus_for_each_drv+0x68/0xd0
    [<00000000b89a83bc>] __device_attach+0xec/0x170
    [<00000000ada2beea>] device_initial_probe+0x14/0x20
    [<0000000079921612>] bus_probe_device+0x9c/0xa8
    [<00000000d268bf7c>] deferred_probe_work_func+0x90/0xd0
    [<000000009ef64bfa>] process_one_work+0x29c/0x788
unreferenced object 0xffff66f243fb2c80 (size 128):
  comm "kworker/u16:0", pid 7, jiffies 4294893319 (age 94.848s)
  hex dump (first 32 bytes):
    62 75 73 5f 61 67 67 72 5f 63 6c 6b 00 00 00 00  bus_aggr_clk....
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................

With this patch no memory leaks are reported.

Link: https://lore.kernel.org/r/20210914092214.6468-1-srinivas.kandagatla@linaro.org
Fixes: aa49761309 ("ufs: Add regulator enable support")
Fixes: c6e79dacd8 ("ufs: Add clock initialization support")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:13:37 -04:00
Arnd Bergmann
bb4a8dcb4e scsi: ufs: mediatek: Avoid sched_clock() misuse
sched_clock() is not meant to be used in portable driver code, and assuming
a particular clock frequency is not how this is meant to be used. It also
causes a build failure because of a missing header inclusion:

drivers/scsi/ufs/ufs-mediatek.c:321:12: error: implicit declaration of function 'sched_clock' [-Werror,-Wimplicit-function-declaration]
        timeout = sched_clock() + retry_ms * 1000000UL;

A better interface to use here ktime_get_mono_fast_ns(), which works mostly
like ktime_get() but is safe to use inside of a suspend callback.

Link: https://lore.kernel.org/r/20211018132022.2281589-1-arnd@kernel.org
Fixes: 9561f58442 ("scsi: ufs: mediatek: Support vops pre suspend to disable auto-hibern8")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 23:09:58 -04:00
Brian King
e20f80b9b1 scsi: ibmvfc: Fix up duplicate response detection
Commit a264cf5e81 ("scsi: ibmvfc: Fix command state accounting and stale
response detection") introduced a regression in detecting duplicate
responses. This was observed in test where a command was sent to the VIOS
and completed before ibmvfc_send_event() set the active flag to 1, which
resulted in the atomic_dec_if_positive() call in ibmvfc_handle_crq()
thinking this was a duplicate response, which resulted in scsi_done() not
getting called, so we then hit a SCSI command timeout for this command once
the timeout expires.  This simply ensures the active flag gets set prior to
making the hcall to send the command to the VIOS, in order to close this
window.

Link: https://lore.kernel.org/r/20211019152129.16558-1-brking@linux.vnet.ibm.com
Fixes: a264cf5e81 ("scsi: ibmvfc: Fix command state accounting and stale response detection")
Cc: stable@vger.kernel.org
Acked-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 22:59:45 -04:00
Jiapeng Chong
0ae8f47851 scsi: mpt3sas: Make mpt3sas_dev_attrs static
This symbol is not used outside of mpt3sas_ctl.c, mark it static.

Fixes the following sparse warning:

drivers/scsi/mpt3sas/mpt3sas_ctl.c:3988:18: warning: symbol
'mpt3sas_dev_attrs' was not declared. Should it be static?

Link: https://lore.kernel.org/r/1634639239-2892-1-git-send-email-jiapeng.chong@linux.alibaba.com
Fixes: 1bb3ca27d2 ("scsi: mpt3sas: Switch to attribute groups")
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-20 22:57:27 -04:00
Qing Wang
db5b6a46f4 net: bpf: Switch over to memdup_user()
This patch fixes the following Coccinelle warning:

net/bpf/test_run.c:361:8-15: WARNING opportunity for memdup_user
net/bpf/test_run.c:1055:8-15: WARNING opportunity for memdup_user

Use memdup_user rather than duplicating its implementation
This is a little bit restricted to reduce false positives

Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/1634556651-38702-1-git-send-email-wangqing@vivo.com
2021-10-20 18:43:15 -07:00
Brendan Jackman
7960d02ddd selftests/bpf: Some more atomic tests
Some new verifier tests that hit some important gaps in the parameter
space for atomic ops.

There are already exhaustive tests for the JIT part in
lib/test_bpf.c, but these exercise the verifier too.

Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20211015093318.1273686-1-jackmanb@google.com
2021-10-20 18:09:08 -07:00
Ian Kent
25f54d08f1 autofs: fix wait name hash calculation in autofs_wait()
There's a mistake in commit 2be7828c9f ("get rid of autofs_getpath()")
that affects kernels from v5.13.0, basically missed because of me not
fully testing the change for Al.

The problem is that the hash calculation for the wait name qstr hasn't
been updated to account for the change to use dentry_path_raw(). This
prevents the correct matching an existing wait resulting in multiple
notifications being sent to the daemon for the same mount which must
not occur.

The problem wasn't discovered earlier because it only occurs when
multiple processes trigger a request for the same mount concurrently
so it only shows up in more aggressive testing.

Fixes: 2be7828c9f ("get rid of autofs_getpath()")
Cc: stable@vger.kernel.org
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2021-10-20 21:09:02 -04:00
Len Baker
50740d5de6 dmaengine: pxa_dma: Prefer struct_size over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.

So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments

Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2021-10-20 18:35:22 -05:00
Len Baker
5dfbbb668a KVM: PPC: Replace zero-length array with flexible array member
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members" [1] for these cases. The
older style of one-element or zero-length arrays should no longer be
used[2].

Also, make use of the struct_size() helper in kzalloc().

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays

Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2021-10-20 18:30:42 -05:00
Len Baker
6446c4fb12 aio: Prefer struct_size over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.

So, use the struct_size() helper to do the arithmetic instead of the
argument "size + size * count" in the kzalloc() function.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments

Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2021-10-20 18:24:31 -05:00
Len Baker
98b160c828 writeback: prefer struct_size over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.

In this case these are not actually dynamic sizes: all the operands
involved in the calculation are constant values. However it is better to
refactor them anyway, just to keep the open-coded math idiom out of
code.

So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() functions.

This code was detected with the help of Coccinelle and audited and fixed
manually.

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments

Signed-off-by: Len Baker <len.baker@gmx.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2021-10-20 18:20:28 -05:00
Gustavo A. R. Silva
c2e4e3b756 xfs: Use kvcalloc() instead of kvzalloc()
Use 2-factor argument multiplication form kvcalloc() instead of
kvzalloc().

Link: https://github.com/KSPP/linux/issues/162
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2021-10-20 18:14:12 -05:00
Caleb Connolly
89139102d3 arm64: dts: qcom: sdm845-oneplus: enable second wifi channel
Like the c630, the OnePlus 6 is also capable of using both antenna
channels for 2.4 and 5ghz wifi, however unlike the c630 only the first
channel is used for bluetooth.

Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020163557.291803-1-caleb@connolly.tech
2021-10-20 18:00:05 -05:00
Kiran Patil
9fea749856 ice: Add tc-flower filter support for channel
Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"

Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.

Example:
MATCH criteria       Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"

Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact

Above two steps are only needed the first time when adding
tc-flower filter.

tc filter add dev <ethX> protocol ip ingress prio 1 flower \
     dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
     skip_sw hw_tc 1

tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
  eth_type ipv4
  ip_proto tcp
  dst_ip 192.168.0.1
  dst_port 5001
  skip_sw
  in_hw in_hw_count 1

Delete specific filter:
-------------------------
tc filter del  dev <ethx> ingress pref 1 handle 0x1 flower

Delete All filters:
------------------
tc filter del dev <ethX> ingress

Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20 15:58:11 -07:00
Kiran Patil
fbc7b27af0 ice: enable ndo_setup_tc support for mqprio_qdisc
Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.

Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
	queues 4@0 4@4 4@8  hw 1 mode channel

Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.

User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.

Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
	num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
	shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
	max_rate 4Gbit 5Gbit 6Gbit 7Gbit

Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>

Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio

Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20 15:58:11 -07:00
Kiran Patil
0754d65bd4 ice: Add infrastructure for mqprio support via ndo_setup_tc
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.

Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-10-20 15:57:54 -07:00
wangyugui
911a81c9c7 RDMA/core: Use kvzalloc when allocating the struct ib_port
The 'struct attribute' flex array contains some struct lock_class_key's
which become big when lockdep is turned on. Big enough that some drivers
will not load when CONFIG_PROVE_LOCKING=y because they cannot allocate
enough memory:

 WARNING: CPU: 36 PID: 8 at mm/page_alloc.c:5350 __alloc_pages+0x27e/0x3e0
  Call Trace:
   kmalloc_order+0x2a/0xb0
   kmalloc_order_trace+0x19/0xf0
   __kmalloc+0x231/0x270
   ib_setup_port_attrs+0xd8/0x870 [ib_core]
   ib_register_device+0x419/0x4e0 [ib_core]
   bnxt_re_task+0x208/0x2d0 [bnxt_re]

Link: https://lore.kernel.org/r/20211019002656.17745-1-wangyugui@e16-tech.com
Signed-off-by: wangyugui <wangyugui@e16-tech.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2021-10-20 19:56:42 -03:00
Zhu Yanjun
dede33da0d RDMA/irdma: Make irdma_uk_cq_init() return a void
The function irdma_uk_cq_init always returns 0, so make it void and delete
all the return value checks.

Link: https://lore.kernel.org/r/20211019153717.3836-1-yanjun.zhu@linux.dev
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2021-10-20 19:54:16 -03:00
Toke Høiland-Jørgensen
dfcb63ce1d fq_codel: generalise ce_threshold marking for subset of traffic
Commit e72aeb9ee0 ("fq_codel: implement L4S style ce_threshold_ect1
marking") expanded the ce_threshold feature of FQ-CoDel so it can
be applied to a subset of the traffic, using the ECT(1) bit of the ECN
field as the classifier. However, hard-coding ECT(1) as the only
classifier for this feature seems limiting, so let's expand it to be more
general.

To this end, change the parameter from a ce_threshold_ect1 boolean, to a
one-byte selector/mask pair (ce_threshold_{selector,mask}) which is applied
to the whole diffserv/ECN field in the IP header. This makes it possible to
classify packets by any value in either the ECN field or the diffserv
field. In particular, setting a selector of INET_ECN_ECT_1 and a mask of
INET_ECN_MASK corresponds to the functionality before this patch, and a
mask of ~INET_ECN_MASK allows using the selector as a straight-forward
match against a diffserv code point:

 # apply ce_threshold to ECT(1) traffic
 tc qdisc replace dev eth0 root fq_codel ce_threshold 1ms ce_threshold_selector 0x1/0x3

 # apply ce_threshold to ECN-capable traffic marked as diffserv AF22
 tc qdisc replace dev eth0 root fq_codel ce_threshold 1ms ce_threshold_selector 0x50/0xfc

Regardless of the selector chosen, the normal rules for ECN-marking of
packets still apply, i.e., the flow must still declare itself ECN-capable
by setting one of the bits in the ECN field to get marked at all.

v2:
- Add tc usage examples to patch description

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211019174709.69081-1-toke@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-20 15:24:36 -07:00
Thiago Rafael Becker
023859ce6f sunrpc: remove unnecessary test in rpc_task_set_client()
In rpc_task_set_client(), testing for a NULL clnt is not necessary, as
clnt should always be a valid pointer to a rpc_client.

Signed-off-by: Thiago Rafael Becker <trbecker@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:55 -04:00
Anna Schumaker
5fe1210d25 NFS: Unexport nfs_probe_fsinfo()
All the callers are now in client.c so we can remove the
EXPORT_SYMBOL_GPL() and make it static.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:55 -04:00
Anna Schumaker
1301ba603c NFS: Call nfs_probe_server() during a fscontext-reconfigure event
This lets us update the server's attributes when the user does a "mount
-o remount" on the filesystem.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:55 -04:00
Anna Schumaker
4d4cf8d2d6 NFS: Replace calls to nfs_probe_fsinfo() with nfs_probe_server()
Clean up. There are a few places where we want to probe the server, but
don't actually care about the fsinfo result. Change these to use
nfs_probe_server(), which handles the fattr allocation for us.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:54 -04:00
Anna Schumaker
e5731131fb NFS: Move nfs_probe_destination() into the generic client
And rename it to nfs_probe_server(). I also change it to take the nfs_fh
as an argument so callers can choose what filehandle to probe.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:54 -04:00
Anna Schumaker
01dde76e47 NFS: Create an nfs4_server_set_init_caps() function
And call it before doing an FSINFO probe to reset to the baseline
capabilities before probing.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
2021-10-20 18:09:54 -04:00