Atm, there are no sink rate values set for DP (vs. eDP) sinks until the
DPCD capabilities are successfully read from the sink. During this time
intel_dp->num_common_rates is 0 which can lead to a
intel_dp->common_rates[-1] (*)
access, which is an undefined behaviour, in the following cases:
- In intel_dp_sync_state(), if the encoder is enabled without a sink
connected to the encoder's connector (BIOS enabled a monitor, but the
user unplugged the monitor until the driver loaded).
- In intel_dp_sync_state() if the encoder is enabled with a sink
connected, but for some reason the DPCD read has failed.
- In intel_dp_compute_link_config() if modesetting a connector without
a sink connected on it.
- In intel_dp_compute_link_config() if modesetting a connector with a
a sink connected on it, but before probing the connector first.
To avoid the (*) access in all the above cases, make sure that the sink
rate table - and hence the common rate table - is always valid, by
setting a default minimum sink rate when registering the connector
before anything could use it.
I also considered setting all the DP link rates by default, so that
modesetting with higher resolution modes also succeeds in the last two
cases above. However in case a sink is not connected that would stop
working after the first modeset, due to the LT fallback logic. So this
would need more work, beyond the scope of this fix.
As I mentioned in the previous patch, I don't think the issue this patch
fixes is user visible, however it is an undefined behaviour by
definition and triggers a BUG() in CONFIG_UBSAN builds, hence CC:stable.
v2: Clear the default sink rates, before initializing these for eDP.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4298
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018143417.1452632-1-imre.deak@intel.com
Reading out the DP encoders' DPCD during booting or resume is only
required for enabled encoders: such encoders may be modesetted during
the initial commit and the link training this involves depends on an
initialized DPCD. For DDI encoders reading out the DPCD is skipped, do
the same on pre-DDI platforms.
Atm, the first DPCD readout without a sink connected - which is a likely
scneario if the encoder is disabled - leaves intel_dp->num_common_rates
at 0, which resulted in
intel_dp_sync_state()->intel_dp_max_common_rate()
in a
intel_dp->common_rates[-1]
access. This by definition results in an undefined behaviour, though to
my best knowledge in all HW/compiler configurations it actually results
in accessing the array item type value preceding the array. In this
case the preceding value happens to be intel_dp->num_common_rates,
which is 0, so this issue - by luck - didn't cause a user visible
problem.
Nevertheless it's still an undefined behaviour and in CONFIG_UBSAN
builds leads to a kernel BUG() (which revealed this problem for us),
hence CC:stable.
A related problem in case the encoder is enabled but the sink is not
connected or the DPCD readout fails is fixed by the next patch.
v2: Amend the commit message describing the root cause of the
CONFIG_UBSAN BUG().
Fixes: a532cde31d ("drm/i915/tc: Fix TypeC port init/resume time sanitization")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/4297
Reported-and-tested-by: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: Mat Jonczyk <mat.jonczyk@o2.pl>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018094154.1407705-2-imre.deak@intel.com
ath.git patches for v5.16. Major changes:
ath9k
* add option to reset the wifi chip via debugfs
* convert Device Tree bindings to the json-schema
* support Device Tree ieee80211-freq-limit property to limit channels
When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.
Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.
So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl
It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl
Fix the return value check which testing the wrong variable
in rtw89_cam_send_sec_key_cmd().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com
When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.
==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...
Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]
Stop thread before free 'common' and 'adapter' to fix it.
Fixes: 2108df3c4b ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com
Update max rx len of some hw modules, which aligns out vendor SDK.
In normal modes, we exchange MPDU 7991 cap with peers; however, this
won't play a part in sniffer mode.
To prevent packets which exceed the max MPDU size from entering specific
rx path in hw, we need to set a proper limit to filter them out.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix missing HE phy cap related to vif and starec setting.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Re-order and modify conditions for MU DL/UL and ofdma DL fields, and
also clean up some unnecessary zero settings.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable HE UL MU-MIMO in sta_rec_muru, which works on both ap and station
mode.
For sending trigger frames, one of the conditions fw uses is to check if
mib rx airtime meets the threshold.
There's a main control of mib rx airtime report register in fw, so we
need to enable the register by mcu cmd instead of directly writing it,
otherwise it will still be disabled by fw.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, add per-vif tx counters in ethtool.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mt7915 driver, add tx/rx statistics reporting through ethtool.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce ethtool stats support to mt7921
driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_amsdu histogram stats in mib_stats structure since registers are
clear-on-read
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since it can run in parallel with mac_work, hold mutex lock in
mt7915_get_et_stats. Moreover update mib counters running
mt7915_get_et_stats.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_ethtool_worker_info in common code in order to be reused in
mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to add ethtool stats to mt7921 driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Appears to have incorrectly offset 0x120 + 0x12 instead of 12 decimal,
leading to bogus power values being used.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce wifi chip reset support for mt7921 device to recover
mcu hangs or abnormal wifi system.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce support for mt7921s 802.11ax (Wi-Fi 6) 2x2:2SS chipset.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Refactor mt7921_mcu_send_message to be sharable between mt7921s and
mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mcu_get_nic_capability to obtain Tx quota information
for the SDIO device, get PHY capability, MAC address and then we can
totally drop mt7921/eeprom.c and any unnecessary code.
Noting that mt76_connac_mcu_get_nic_capability should be run before set
flag MT76_STATE_MCU_RUNNING being set to setup the proper parameters
like Tx quota control before the device is started to running.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend mcu_get_nic_capability to obtain tx resource for SDIO device,
MAC address, and PHY capability.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend sdio module to support CONNAC2 hw that mt7921s rely on.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add parse_irq to handle that interrupt status structure is
different between mt7663s and mt7921s.
This is a preliminary patch to introduce mt7921s driver
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use physical address to unify the register access and reorder the
entries in fixed_map table to accelerate the address lookup for
MT7921e. Cosmetics the patch with adding an extra space to make all
entries in the array style consistent.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The longer event such as the event for mcu_get_nic_capability would hold
the data in paged fragment skb for the SDIO device so we turn the skb to
be linearized skb before accessing it to reuse the same event parser
betweem mt7921s and mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
rely on mcu reg access utility and drop the duplicated code.
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu reg access shared between mt7663s and mt7921s in mt76_connac_lib
module.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
MT7921_COMMON module grouping bus independent objects the both mt7921e and
mt7921s can share with and have to rely on.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Make init.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Make mcu.c reusable between mt7921s and mt7921e
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
make dma.c be used dedicately for mt7921e.
by moving out mt7921_tx_cleanup from dma.c to mcu.c and then renaming
mt7921_tx_cleanup to refect the exact thing the function actually does.
Finally, dma.c totally become pcie specific one, only needed to
be compiled only when CONFIG_MT7921E is enabled.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce mt7921s support.
Split out a new pci_mac.c from mac.c to make mac.c reusable between
mt7921s and mt7921e.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add MU EDCA MCU command support to update MU AC parameter record field
from the access point.
Co-developed-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Tested-by: Eric-SY Chang <Eric-SY.Chang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove some more not used code in mt7915 debugfs.
Squash mt7915_puts_rate_txpower and mt7915_rate_txpower_show.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Improve xmit-queue debugfs node readability for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a dedicated mt76 debugfs sub-dir for ext-phy in dbdc mode.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to create a mt76 debugfs subir for ext-phy.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>