SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have this in two places, so let's have a dedicated function. It is
also more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I wanted to use it in a wrong way, so document the intended way.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624151616.38770-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DP 2.0 UHBR link rates always use 128b/132b channel encoding, which has
a different data bandwidth efficiency from 8b/10b. The computation is
slightly convoluted due to the units we use; this is all explained in
the added comment.
v2: Clarified comment (Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8afd8d97a04c2d86c2dcadfed9f8e1f84272a13c.1629735412.git.jani.nikula@intel.com
The MST code uses actual link rates in the limits struct, while the DP
code in general uses indexes to the ->common_rates[] array. Fix the
confusion by using actual link rate values everywhere. This is a better
abstraction than some obscure index.
Rename the struct members while at it to ensure all the places are
covered.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d70ab7261abacd367d3a6a47102575eb88a55cd4.1629735412.git.jani.nikula@intel.com
PCI devices expose the associated MSI interrupts via sysfs, but platform
devices which utilize MSI interrupts do not. This information is important
for user space tools to optimize affinity settings.
Utilize the generic MSI sysfs facility to expose this information for
platform MSI.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210813035628.6844-3-21cnbao@gmail.com
Move PCI's MSI sysfs code to the irq core so that other busses such as
platform can reuse it.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210813035628.6844-2-21cnbao@gmail.com
This sort of information is only generally useful when debugging.
No need to have these sprinkled through the kernel log otherwise.
Real world problem:
During pre-release testing these have an affect on performance on
real products. To the point where so much logging builds up, that
it sets off the watchdog(s) on some high profile consumer devices.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210816134817.1503661-1-lee.jones@linaro.org
The recent quirk for WALKMAN (commit 7af5a14371: "ALSA: usb-audio:
Fix regression on Sony WALKMAN NW-A45 DAC") may be required for other
devices and is worth to be put into the common quirk flags.
This patch adds a new quirk flag bit QUIRK_FLAG_SET_IFACE_FIRST and a
quirk table entry for the device.
Link: https://lore.kernel.org/r/20210824055720.9240-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch extends support for the HP Spectre x360 14
amp enable quirk to support a model of the device with
an additional subdevice ID.
Signed-off-by: Johnathon Clark <john.clark@cantab.net>
Link: https://lore.kernel.org/r/20210823162110.8870-1-john.clark@cantab.net
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a regression report for USB-audio with Sony WALKMAN NW-A45
DAC device where no sound is audible on recent kernel. The bisection
resulted in the code change wrt endpoint management, and the further
debug session revealed that it was caused by the order of the USB
audio interface. In the earlier code, we always set up the USB
interface at first before other setups, but it was changed to be done
at the last for UAC2/3, which is more standard way, while keeping the
old way for UAC1. OTOH, this device seems requiring the setup of the
interface at first just like UAC1.
This patch works around the regression by applying the interface setup
specifically for the WALKMAN at the beginning of the endpoint setup
procedure. This change is written straightforwardly to be easily
backported in old kernels. A further cleanup to move the workaround
into a generic quirk section will follow in a later patch.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214105
Link: https://lore.kernel.org/r/20210824054700.8236-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add FORCE so that if_changed can detect the command line change.
scsi_devinfo_tbl.c must be added to 'targets' too.
Link: https://lore.kernel.org/r/20210819012339.709409-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device reset and target reset will be using different calling sequences, so
open-code __qla2xxx_eh_generic_reset() in qla2xxx_eh_device_reset(), and
remove the now obsolete function __qla2xxx_eh_generic_reset(). No
functional changes.
Link: https://lore.kernel.org/r/20210819091913.94436-4-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Device reset and target reset will be using different calling sequences, so
open-code __qla2xxx_eh_generic_reset() in qla2xxx_eh_target_reset(). No
functional changes.
Link: https://lore.kernel.org/r/20210819091913.94436-3-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When calling bus reset the driver will be doing a full SAN resync, so there
is no need to wait for any pending RSCNs; they'll be re-issued during
resync anyway.
Link: https://lore.kernel.org/r/20210819091913.94436-2-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When Target port transitions personality from one to another (NVMe <-->
FCP), there could be some overlap of the two where one layer is going down
while the other layer is coming up. This overlap can cause temporary I/O
error. Detect those errors/transitions and recover from them. Triggers
session tear down and allow relogin to re-drive the connection under the
following conditions:
- NVMe command error
- On PRLO + N2N (rida format 2)
Link: https://lore.kernel.org/r/20210817051315.2477-11-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target port that register itself as both FCP + NVMe, initiator driver
will try to login one mode at a time. If the last mode did not succeed,
then driver will try the other mode.
When error is encountered, current code only flip to other mode one time
(NVMe->FCP) and remain on the last mode. Driver wrongly assumed target
port does not support PRLI NVMe, instead it was not ready to receive PRLI.
This patch will alternate back and forth on every PRLI failure until login
retry count has depleted or it is succeeded.
Link: https://lore.kernel.org/r/20210817051315.2477-10-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The abort callback gets called only when it gets posted to firmware. The
refcounting is done properly in the callback. On internal errors, the
callback is not invoked leading to a hung I/O. Fix this by having separate
error code when command gets returned from firmware.
Link: https://lore.kernel.org/r/20210817051315.2477-9-njavali@marvell.com
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver saves the personality type (FCP|NVMe) at the start of
first discovery of the remote device. If the remote device personality do
change over time, then qla driver needs to present that to user to decide.
Link: https://lore.kernel.org/r/20210817051315.2477-8-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For initiator mode, always do secure login when authentication app started.
Also remove redundant flags to indicate secure connection.
Link: https://lore.kernel.org/r/20210817051315.2477-7-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For EDIF + N2N to work, firmware 9.8 or later is required. The driver will
pause after PLOGI to allow app to authenticate. Once authentication
completes, app will tell driver to do PRLI.
Link: https://lore.kernel.org/r/20210817051315.2477-6-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following hung task call trace was seen:
[ 1230.183294] INFO: task qla2xxx_wq:523 blocked for more than 120 seconds.
[ 1230.197749] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1230.205585] qla2xxx_wq D 0 523 2 0x80004000
[ 1230.205636] Workqueue: qla2xxx_wq qlt_free_session_done [qla2xxx]
[ 1230.205639] Call Trace:
[ 1230.208100] __schedule+0x2c4/0x700
[ 1230.211607] schedule+0x38/0xa0
[ 1230.214769] schedule_timeout+0x246/0x2f0
[ 1230.222651] wait_for_completion+0x97/0x100
[ 1230.226921] qlt_free_session_done+0x6a0/0x6f0 [qla2xxx]
[ 1230.232254] process_one_work+0x1a7/0x360
...when device side port resets were done.
Abort threads were getting out without processing due to the "deleted"
flag check. The delete thread, meanwhile, could not proceed with a
logout (that would have cleared out pending requests) as the logout IOCB
work was not progressing. It appears like the hung qlt_free_session_done()
thread is causing the ha->wq works on hold. The qlt_free_session_done()
was hung waiting for nvme_fc_unregister_remoteport() + localport_delete cb
to be complete, which would only happen when all I/Os are released.
Fix this by allowing abort to progress until device delete is completely
done. This should make the qlt_free_session_done() proceed without hang and
thus clear up the deadlock.
Link: https://lore.kernel.org/r/20210817051315.2477-5-njavali@marvell.com
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
edif_enabled is prematurely turned on if hardware is capable of handling
the feature. However, firmware also needs to support EDIF before enabling
this bit.
Link: https://lore.kernel.org/r/20210817051315.2477-4-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reject inflight AUTH ELS if driver is going through session recovery.
Link: https://lore.kernel.org/r/20210817051315.2477-3-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When firmware indicates session has been torn down via UPDATE SA IOCB or
ELS Passthrough IOCB, the driver needs to also tear down the session.
Link: https://lore.kernel.org/r/20210817051315.2477-2-njavali@marvell.com
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch extends wait time in timer_mim. As observed in slow CI environment,
it is possible to have interrupt/preemption long enough to cause the test to
fail, almost 1 failure in 5 runs.
Signed-off-by: Yucong Sun <fallentree@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210823213629.3519641-1-fallentree@fb.com
Dave Marchevsky says:
====================
The cgroup_bpf struct has a few arrays (effective, progs, and flags) of
size MAX_BPF_ATTACH_TYPE. These are meant to separate progs by their
attach type, currently represented by the bpf_attach_type enum.
There are some bpf_attach_type values which are not valid attach types
for cgroup bpf programs. Programs with these attach types will never be
handled by cgroup_bpf_{attach,detach} and thus will never be held in
cgroup_bpf structs. Even if such programs did make it into their
reserved slot in those arrays, they would never be executed.
Accordingly we can migrate to a new internal cgroup_bpf-specific enum
for these arrays, saving some bytes per cgroup and making it more
obvious which BPF programs belong there. netns_bpf_attach_type is an
existing example of this pattern, let's do similar for cgroup_bpf.
v1->v2: Address Daniel's comments
* Reverse xmas tree ordering for def changes
* Helper macro to reduce to_cgroup_bpf_attach_type boilerplate
* checkpatch.pl complains: "ERROR: Macros with complex values should
be enclosed in parentheses". Found some existing macros (do 'git grep
"define case"') which get same complaint. Think it's fine to keep
as-is since it's immediately undef'd.
* Remove CG_BPF_ prefix from cgroup_bpf_attach_type
* Although I agree that the prefix is redundant, the de-prefixed
names feel a bit too 'general' given the internal use of the enum.
e.g. when someone sees CGROUP_INET6_BIND it's not obvious that it
should only be used in certain ways internally.
* Don't feel strongly about this, just my thoughts as a noob to the
internals.
* Rebase onto latest bpf-next/master
* No significant conflicts, some small boilerplate adjustments
needed to catch up to Andrii's "bpf: Refactor BPF_PROG_RUN_ARRAY
family of macros into functions" change
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add an enum (cgroup_bpf_attach_type) containing only valid cgroup_bpf
attach types and a function to map bpf_attach_type values to the new
enum. Inspired by netns_bpf_attach_type.
Then, migrate cgroup_bpf to use cgroup_bpf_attach_type wherever
possible. Functionality is unchanged as attach_type_to_prog_type
switches in bpf/syscall.c were preventing non-cgroup programs from
making use of the invalid cgroup_bpf array slots.
As a result struct cgroup_bpf uses 504 fewer bytes relative to when its
arrays were sized using MAX_BPF_ATTACH_TYPE.
bpf_cgroup_storage is notably not migrated as struct
bpf_cgroup_storage_key is part of uapi and contains a bpf_attach_type
member which is not meant to be opaque. Similarly, bpf_cgroup_link
continues to report its bpf_attach_type member to userspace via fdinfo
and bpf_link_info.
To ease disambiguation, bpf_attach_type variables are renamed from
'type' to 'atype' when changed to cgroup_bpf_attach_type.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210819092420.1984861-2-davemarchevsky@fb.com
While prototyping a free space defragmentation tool, I observed an
unexpected IO error while running a sequence of commands that can be
recreated by the following sequence of commands:
# xfs_io -f -c "pwrite -S 0x58 -b 10m 0 10m" file1
# cp --reflink=always file1 file2
# punch-alternating -o 1 file2
# xfs_io -c "funshare 0 10m" file2
fallocate: Input/output error
I then scraped this (abbreviated) stack trace from dmesg:
WARNING: CPU: 0 PID: 30788 at fs/iomap/buffered-io.c:577 iomap_write_begin+0x376/0x450
CPU: 0 PID: 30788 Comm: xfs_io Not tainted 5.14.0-rc6-xfsx #rc6 5ef57b62a900814b3e4d885c755e9014541c8732
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:iomap_write_begin+0x376/0x450
RSP: 0018:ffffc90000c0fc20 EFLAGS: 00010297
RAX: 0000000000000001 RBX: ffffc90000c0fd10 RCX: 0000000000001000
RDX: ffffc90000c0fc54 RSI: 000000000000000c RDI: 000000000000000c
RBP: ffff888005d5dbd8 R08: 0000000000102000 R09: ffffc90000c0fc50
R10: 0000000000b00000 R11: 0000000000101000 R12: ffffea0000336c40
R13: 0000000000001000 R14: ffffc90000c0fd10 R15: 0000000000101000
FS: 00007f4b8f62fe40(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000056361c554108 CR3: 000000000524e004 CR4: 00000000001706f0
Call Trace:
iomap_unshare_actor+0x95/0x140
iomap_apply+0xfa/0x300
iomap_file_unshare+0x44/0x60
xfs_reflink_unshare+0x50/0x140 [xfs 61947ea9b3a73e79d747dbc1b90205e7987e4195]
xfs_file_fallocate+0x27c/0x610 [xfs 61947ea9b3a73e79d747dbc1b90205e7987e4195]
vfs_fallocate+0x133/0x330
__x64_sys_fallocate+0x3e/0x70
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f4b8f79140a
Looking at the iomap tracepoints, I saw this:
iomap_iter: dev 8:64 ino 0x100 pos 0 length 0 flags WRITE|0x80 (0x81) ops xfs_buffered_write_iomap_ops caller iomap_file_unshare
iomap_iter_dstmap: dev 8:64 ino 0x100 bdev 8:64 addr -1 offset 0 length 131072 type DELALLOC flags SHARED
iomap_iter_srcmap: dev 8:64 ino 0x100 bdev 8:64 addr 147456 offset 0 length 4096 type MAPPED flags
iomap_iter: dev 8:64 ino 0x100 pos 0 length 4096 flags WRITE|0x80 (0x81) ops xfs_buffered_write_iomap_ops caller iomap_file_unshare
iomap_iter_dstmap: dev 8:64 ino 0x100 bdev 8:64 addr -1 offset 4096 length 4096 type DELALLOC flags SHARED
console: WARNING: CPU: 0 PID: 30788 at fs/iomap/buffered-io.c:577 iomap_write_begin+0x376/0x450
The first time funshare calls ->iomap_begin, xfs sees that the first
block is shared and creates a 128k delalloc reservation in the COW fork.
The delalloc reservation is returned as dstmap, and the shared block is
returned as srcmap. So far so good.
funshare calls ->iomap_begin to try the second block. This time there's
no srcmap (punch-alternating punched it out!) but we still have the
delalloc reservation in the COW fork. Therefore, we again return the
reservation as dstmap and the hole as srcmap. iomap_unshare_iter
incorrectly tries to unshare the hole, which __iomap_write_begin rejects
because shared regions must be fully written and therefore cannot
require zeroing.
Therefore, change the buffered write iomap_begin function not to set
IOMAP_F_SHARED when there isn't a source mapping to read from for the
unsharing.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
The new function validate_hash_algo() assumed that ima_get_hash_algo()
always return a valid 'enum hash_algo', but it returned the
user-supplied value present in the digital signature without
any bounds checks.
Update ima_get_hash_algo() to always return a valid hash algorithm,
defaulting on 'ima_hash_algo' when the user-supplied value inside
the xattr is invalid.
Signed-off-by: THOBY Simon <Simon.THOBY@viveris.fr>
Reported-by: syzbot+e8bafe7b82c739eaf153@syzkaller.appspotmail.com
Fixes: 50f742dd91 ("IMA: block writes of the security.ima xattr with unsupported algorithms")
Reviewed-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
We shouldn't really be using a read-only file descriptor to take a write
lock.
Most filesystems will put up with it. But NFS, for example, won't.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
"Ma, XinjianX" <xinjianx.ma@intel.com> reported:
> When lkp team run kernel selftests, we found after these series of patches, testcase mqueue: mq_perf_tests
> in kselftest failed with following message.
>
> # selftests: mqueue: mq_perf_tests
> #
> # Initial system state:
> # Using queue path: /mq_perf_tests
> # RLIMIT_MSGQUEUE(soft): 819200
> # RLIMIT_MSGQUEUE(hard): 819200
> # Maximum Message Size: 8192
> # Maximum Queue Size: 10
> # Nice value: 0
> #
> # Adjusted system state for testing:
> # RLIMIT_MSGQUEUE(soft): (unlimited)
> # RLIMIT_MSGQUEUE(hard): (unlimited)
> # Maximum Message Size: 16777216
> # Maximum Queue Size: 65530
> # Nice value: -20
> # Continuous mode: (disabled)
> # CPUs to pin: 3
> # ./mq_perf_tests: mq_open() at 296: Too many open files
> not ok 2 selftests: mqueue: mq_perf_tests # exit=1
> ```
>
> Test env:
> rootfs: debian-10
> gcc version: 9
After investigation the problem turned out to be that ucount_max for
the rlimits in init_user_ns was being set to the initial rlimit value.
The practical problem is that ucount_max provides a limit that
applications inside the user namespace can not exceed. Which means in
practice that rlimits that have been converted to use the ucount
infrastructure were not able to exceend their initial rlimits.
Solve this by setting the relevant values of ucount_max to
RLIM_INIFINITY. A limit in init_user_ns is pointless so the code
should allow the values to grow as large as possible without riscking
an underflow or an overflow.
As the ltp test case was a bit of a pain I have reproduced the rlimit failure
and tested the fix with the following little C program:
> #include <stdio.h>
> #include <fcntl.h>
> #include <sys/stat.h>
> #include <mqueue.h>
> #include <sys/time.h>
> #include <sys/resource.h>
> #include <errno.h>
> #include <string.h>
> #include <stdlib.h>
> #include <limits.h>
> #include <unistd.h>
>
> int main(int argc, char **argv)
> {
> struct mq_attr mq_attr;
> struct rlimit rlim;
> mqd_t mqd;
> int ret;
>
> ret = getrlimit(RLIMIT_MSGQUEUE, &rlim);
> if (ret != 0) {
> fprintf(stderr, "getrlimit(RLIMIT_MSGQUEUE) failed: %s\n", strerror(errno));
> exit(EXIT_FAILURE);
> }
> printf("RLIMIT_MSGQUEUE %lu %lu\n",
> rlim.rlim_cur, rlim.rlim_max);
> rlim.rlim_cur = RLIM_INFINITY;
> rlim.rlim_max = RLIM_INFINITY;
> ret = setrlimit(RLIMIT_MSGQUEUE, &rlim);
> if (ret != 0) {
> fprintf(stderr, "setrlimit(RLIMIT_MSGQUEUE, RLIM_INFINITY) failed: %s\n", strerror(errno));
> exit(EXIT_FAILURE);
> }
>
> memset(&mq_attr, 0, sizeof(struct mq_attr));
> mq_attr.mq_maxmsg = 65536 - 1;
> mq_attr.mq_msgsize = 16*1024*1024 - 1;
>
> mqd = mq_open("/mq_rlimit_test", O_RDONLY|O_CREAT, 0600, &mq_attr);
> if (mqd == (mqd_t)-1) {
> fprintf(stderr, "mq_open failed: %s\n", strerror(errno));
> exit(EXIT_FAILURE);
> }
> ret = mq_close(mqd);
> if (ret) {
> fprintf(stderr, "mq_close failed; %s\n", strerror(errno));
> exit(EXIT_FAILURE);
> }
>
> return EXIT_SUCCESS;
> }
Fixes: 6e52a9f053 ("Reimplement RLIMIT_MSGQUEUE on top of ucounts")
Fixes: d7c9e99aee ("Reimplement RLIMIT_MEMLOCK on top of ucounts")
Fixes: d646969055 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
Fixes: 21d1c5e386 ("Reimplement RLIMIT_NPROC on top of ucounts")
Reported-by: kernel test robot lkp@intel.com
Acked-by: Alexey Gladkov <legion@kernel.org>
Link: https://lkml.kernel.org/r/87eeajswfc.fsf_-_@disp2133
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Commit 457f44363a ("bpf: Implement BPF ring buffer and verifier support
for it") extended check_map_func_compatibility() by enforcing map -> helper
function match, but not helper -> map type match.
Due to this all of the bpf_ringbuf_*() helper functions could be used with
a wrong map type such as array or hash map, leading to invalid access due
to type confusion.
Also, both BPF_FUNC_ringbuf_{submit,discard} have ARG_PTR_TO_ALLOC_MEM as
argument and not a BPF map. Therefore, their check_map_func_compatibility()
presence is incorrect since it's only for map type checking.
Fixes: 457f44363a ("bpf: Implement BPF ring buffer and verifier support for it")
Reported-by: Ryota Shiga (Flatt Security)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
IORING_OP_LINKAT behaves like linkat(2) and takes the same flags and
arguments.
In some internal places 'hardlink' is used instead of 'link' to avoid
confusion with the SQE links. Name 'link' conflicts with the existing
'link' member of io_kiocb.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/io-uring/20210514145259.wtl4xcsp52woi6ab@wittgenstein/
Signed-off-by: Dmitry Kadashev <dkadashev@gmail.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20210708063447.3556403-12-dkadashev@gmail.com
[axboe: add splice_fd_in check]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We're missing a description for the 'nr_vecs' parameter. While in there,
clarify that freeing a bio allocated through this function must be done
from process context.
Fixes: 1cbbd31c4ada ("bio: add allocation cache abstraction")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Any case that turns off REQ_HIPRI must also clear BIO_PERCPU_CACHE,
as non-polled IO may complete through hard/soft IRQ and hence isn't
safe for our polled bio alloc cache.
Provide a helper that does just that, and use it in the merging code as
well if we split a bio and turn off polling.
Fixes: be863b9e43 ("block: clear BIO_PERCPU_CACHE flag if polling isn't supported")
Reported-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use bio_alloc_kiocb to dip into the percpu cache of bios when the
caller asks for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>