thermometer_add_tz() opens tz_path and then reallocates thermometer->tz.
If realloc fails, the function returns without closing fd.
Close fd before returning on realloc failure to avoid leaking a file descriptor.
Signed-off-by: Amarjeet <amarjeet@intel.com>
Link: https://patch.msgid.link/20260620122637.1334927-1-amarjeet@intel.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for the IPQ9650 platform, which includes three Gen3 x2 PCIe
controllers and two Gen3 x1 PCIe controllers. The PHY instances require
the on-chip refgen supply.
Add the IPQ9650 Gen3 x1 and x2 QMP PCIe PHY configurations along with
the refgen regulator supply. Note that an on-chip LDO, driven by the SoC
CX, supplies the PHY voltages without requiring software control. Note
that IPQ9650 does not support CX power collapse or rail scaling.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710-ipq9650_pcie_phy-v3-2-ef6018818d33@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document the single-lane and dual-lane QMP PCIe PHYs found on the
IPQ9650 SoC.
Unlike the PHYs in the other supported IPQ SoCs, the IPQ9650 PHYs require
the on-chip refgen supply to power up. Add the refgen-supply property
and require it only for the IPQ9650 compatibles.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710-ipq9650_pcie_phy-v3-1-ef6018818d33@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is the Chinese translation subtree for 7.3. It includes
the following changes:
- Add the some rust, module-signing docs translation
- Fix/update couples Chinese translation
Above patches are tested by 'make htmldocs'
Signed-off-by: Alex Shi <alexs@kernel.org>
-----BEGIN PGP SIGNATURE-----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=uzq2
-----END PGP SIGNATURE-----
Merge tag 'Chinese-docs-7.3' of gitolite.kernel.org:pub/scm/linux/kernel/git/alexs/linux into alex
Chinese translation docs for 7.3
This is the Chinese translation subtree for 7.3. It includes
the following changes:
- Add the some rust, module-signing docs translation
- Fix/update couples Chinese translation
Above patches are tested by 'make htmldocs'
Signed-off-by: Alex Shi <alexs@kernel.org>
Swap the entries for 3562 and 3563 to keep the table in order of
increasing part number.
There's nothing broken here, it's just cosmetic.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20260722143607.1001473-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mike Rapoport says:
====================
bpf, x86: enable EXECMEM_ROX_CACHE for BPF allocations
Hi,
BPF allocations of executable memory on x86 are essentially read-only. Most
paths that call bpf_jit_alloc_exec() immediately make it ROX with
set_memory_rox().
The code generation, at least on x86, uses separately allocated writable
buffers and then updates the actual text memory with text_poke().
These patches do several small adjustments to how BPF allocates executable
memory and enable EXECMEM_ROX_CACHE for BPF allocations on x86.
Acked-by: Song Liu <song@kernel.org>
---
v3 changes:
* replace vmalloc() with vzalloc() in bpf_dispatcher_change_prog()
* rebase on the current bpf-next
v2: https://patch.msgid.link/20260711-execmem-x86-rox-bpf-v0-v2-0-bfd956d35119@kernel.org
* rebase on the current bpf-next
v1: https://patch.msgid.link/20260626-execmem-x86-rox-bpf-v0-v1-0-45a0b0ed4fe9@kernel.org
---
---
Mike Rapoport (Microsoft) (5):
bpf: dispatcher: allocate bpf_dispatcher->rw_image with vzalloc()
bpf: drop __weak from bpf_jit_alloc_exec() and bpf_jit_free_exec()
bpf: alloc_prog_pack(): skip ROX management for already ROX memory
bpf, x86: make sure allocation in arch_bpf_trampoline_size() is writable
x86/bpf: enable EXECMEM_ROX_CACHE for BPF allocations
arch/x86/mm/init.c | 4 ++--
arch/x86/net/bpf_jit_comp.c | 5 ++---
include/linux/filter.h | 1 +
kernel/bpf/core.c | 30 +++++++++++++++++++++---------
kernel/bpf/dispatcher.c | 5 ++++-
5 files changed, 30 insertions(+), 15 deletions(-)
---
base-commit: d1f4b56417
change-id: 20260626-execmem-x86-rox-bpf-v0-b4241ade80df
--
Sincerely yours,
Mike.
====================
Link: https://patch.msgid.link/20260716-execmem-x86-rox-bpf-v0-v3-0-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
BPF core and x86 JIT use text poking and temporary writable buffers and
thus can handle ROX memory.
Enable ROX cache for EXECMEM_BPF when configuration and CPU features allow
that.
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-5-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
arch_bpf_trampoline_size() allocates a buffer to get actual size required
for a trampoline.
This buffer must be in the module address space because
__arch_prepare_bpf_trampoline() calculates rel32 offsets relatively to
that buffer.
In preparation for enabling ROX mode for EXECMEM_BPF make sure that the
allocated memory is writable.
Add bpf_jit_alloc_exec_rw() wrapper for execmem_alloc_rw() and use it for
buffer allocation in arch_bpf_trampoline_size().
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-4-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
execmem_alloc() can return ROX memory that is already filled with
architecture defined trapping instructions.
In preparation for enabling this mode for BPF on x86, make sure that there
is no redundant management of the ROX memory.
There is no need to fill allocated memory with trapping instructions, to
request permissions reset on free and to set ROX permissions as this all
is handled by execmem_alloc().
Add bpf_jit_mem_is_rox() wrapper for execmem_is_rox(), use it to check if
execmem_alloc() returns ROX memory and skip the redundant steps in that
case.
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-3-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
bpf_jit_alloc_exec() and bpf_jit_free_exec() are wrappers for the
corresponding execmem APIs.
Architectures define the properties of the memory range needed by BPF in
their initialization of execmem and don't need to override neither of
them.
Drop the __weak qualifier from bpf_jit_alloc_exec() and
bpf_jit_free_exec().
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-2-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
bpf_dispatcher->rw_image is a temporary writable buffer that
arch_prepare_bpf_dispatcher() fills and then copies into
bpf_dispatcher->image using bpf_arch_text_copy().
The rel32 offsets emitted by emit_bpf_dispatcher() are calculated against
->image, so ->rw_image does not need to live in the module address range.
Allocate ->rw_image with vzalloc() to avoid permissions dance when
EXECMEM_BPF will be backed by ROX caches.
Using vzalloc() rather than vmalloc() ensures that the memory that
bpf_dispatcher_update() unconditionally copies into the executable buffer
is zeroed, which is not ideal but still better than random memory returned
by the existing bpf_jit_alloc_exec() or plain vmalloc().
Switching from bpf_jit_alloc_exec() to vzalloc() also saves a bit of
space in the more scarce module address space.
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/bpf/20260716-execmem-x86-rox-bpf-v0-v3-1-4e76158c01c5@kernel.org
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
In data=journal mode, the writeback thread can hit the
WARN_ON_ONCE(sb_rdonly(sb)) in ext4_journal_check_start() while the
superblock is being remounted read-only during reboot:
Workqueue: writeback wb_workfn (flush-253:0)
RIP: 0010:ext4_journal_check_start+0x8b/0xd0
Call Trace:
__ext4_journal_start_sb+0x3c/0x1e0
mpage_prepare_extent_to_map+0x4af/0x580
ext4_do_writepages+0x3c0/0x1080
ext4_writepages+0xc8/0x1a0
do_writepages+0xc4/0x180
__writeback_single_inode+0x45/0x2f0
writeback_sb_inodes+0x26b/0x5d0
__writeback_inodes_wb+0x54/0x100
wb_writeback+0x1ac/0x320
wb_workfn+0x394/0x470
And followed by the warning:
EXT4-fs warning (device vda1): ext4_evict_inode:195: inode #6263:
comm (sd-umount): data will be lost
This issue is not reproduced every time, but frequently.
The reproduction step is to create a VM with 8 CPUs, 16G memory and
setup data=journal:
sudo tune2fs -o journal_data /dev/vda1
Run fio:
rm -f fiotest
fio --name=fiotest --rw=randwrite --bs=4k --runtime=6 --ioengine=libaio
--iodepth=256 --numjobs=8 --filename=fiotest --filesize=30G
--group_reporting
Reboot the VM, and check the console output from:
virsh console testvm
But there is no dirty inode, folio_clear_dirty_for_io clears PG_dirty
but leaves tags PAGECACHE_TAG_DIRTY and PAGECACHE_TAG_TOWRITE set which
are only cleared by __folio_start_writeback.
In data=journal mode, jbd2 checkpoints the journalled data to its final
location and clears its own dirty flag without touching folio PG_dirty
or xarray dirty flags.
The commit f4a2b42e78 ("ext4: fix stale xarray tags after writeback")
fixes when PG_dirty is still set but there is no dirty page.
Another case is PG_dirty is cleared, but PAGECACHE_TAG_DIRTY and
PAGECACHE_TAG_TOWRITE is still set. In this case, writeback thread
checks clean folio and skips it in mpage_prepare_extent_to_map:
if (!folio_test_dirty(folio) ||
...
folio_unlcok(folio);
continue
And never reaches ext4_bio_write_folio where the commit f4a2b42e78
clears the stale xarray tags. Print debug logs after the filesystem
is remounted read-only:
writepages RDONLY nrpages=2048 dirtytag=1 wbtag=0 towrite=1 sync=0
And all folios are actually clean:
folio idx=3 dirty=0 wb=0 checked=0 dirtybuf=0 jbddirty=0 mapped=1
...
We need to clear the xarray stale tags for such clean folios by
cycling them through writeback in the skip path, the same way
f4a2b42e78 does in ext4_bio_write_folio.
Fixes: dff4ac75ee ("ext4: move keep_towrite handling to ext4_bio_write_page()")
Signed-off-by: Gerald Yang <gerald.yang@canonical.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260625160127.162272-1-gerald.yang@canonical.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
USB Gen1 requires scrambling and 8b/10b encoding to be performed in the
physical layer. Do not bypass PHY-side scrambler or encoder/decoder for
USB operation, as mandated by the USB 3.x specification.
Scrambler and 8b/10b bypass remain restricted to SATA and SGMII
modes, where encoding is handled in the controller.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Cc: stable@vger.kernel.org
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260627155229.2791113-4-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
xpsgtr_bypass_scrambler_8b10b() used xpsgtr_write_phy() which performs
a full register write, silently clearing any bits beyond the intended
bypass control fields.
Switch to xpsgtr_clr_set_phy() with clr=mask, set=mask to set only
the bypass bits while preserving the remaining bits in each register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Cc: stable@vger.kernel.org
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260627155229.2791113-3-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The L0_TX_DIG_61 register bit 2 is a reserved read-only field.
The previous mask value 0x0f incorrectly included bit 2, causing
unintended writes to a reserved bit on every scrambler bypass
operation.
Correct the mask to (BIT(3) | GENMASK(1, 0)) to cover only the
valid scramble bypass control bits.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Cc: stable@vger.kernel.org
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260627155229.2791113-2-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Correct spaces or mix of tabs+spaces into proper tab-indented lines.
No functional impact (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Syzbot/stress-ng reported an ABBA deadlock in ext4 when exercising
concurrent xattr workloads (using the ea_inode mount/format option).
The deadlock occurs between the running transaction and the eviction
thread:
- Task 1 (stress-ng): Holds a reference to a shared mbcache_entry (ce)
and calls ext4_xattr_inode_cache_find() -> ext4_iget() to retrieve
the corresponding EA inode. Since the EA inode is currently being
evicted, ext4_iget() blocks in __wait_on_freeing_inode() waiting for
eviction to complete.
- Task 2 (eviction thread): Currently evicting the same EA inode in
ext4_evict_ea_inode(). It calls mb_cache_entry_wait_unused(oe) which
blocks waiting for Task 1 to release the reference to the mbcache_entry.
To break this deadlock, implement a new ext4_iget() configuration flag
named EXT4_IGET_NOWAIT. When set, perform a non-blocking lookup of the
inode via VFS's find_inode_nowait() API.
If the inode is currently being evicted (marked with I_FREEING or
I_WILL_FREE) or created (I_CREATING), or if it is not present in the VFS
inode cache (cache miss), simply skip it (returning -ENOENT) rather than
waiting for eviction/creation to complete, breaking the ABBA cycle.
Since we return -ENOENT immediately on a cache miss, we never attempt to
allocate a new inode or call iget_locked(), completely eliminating any
TOCTOU race window.
If the returned inode is I_NEW, wait for its initialization to clear via
wait_on_new_inode(). If initialization fails and the inode is unhashed
during wait_on_new_inode() waking up (e.g., due to an I/O read error in
another thread), safely drop the reference and return -ENOENT. This
unhashed check is executed unconditionally on all cache-hit pathways to
properly handle concurrent initialization failures.
Finally, standard validation checks (including is_bad_inode,
EXT4_EA_INODE_FL, file_acl, and xattr flags) are executed as normal inside
check_igot_inode() to fully guarantee VFS-layer safety.
In ext4_xattr_inode_cache_find(), invoke ext4_iget() with the new
EXT4_IGET_NOWAIT flag to perform the non-blocking cache search.
Suggested-by: Jan Kara <jack@suse.cz>
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219283
Fixes: 0a46ef2347 ("ext4: do not create EA inode under buffer lock")
Signed-off-by: Aditya Prakash Srivastava <aditya.ansh182@gmail.com>
Tested-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20260626054821.1729-1-aditya.ansh182@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Convert Texas Instruments Wakeup M3 Remote Processor from text to Dt
schema. Add optional resets and reset-names property which was missing
from legacy binding. make ti,hwmods deprecated as it no longer needed,
it is kept to support older board files without ti,sysc.
Signed-off-by: Bhargav Joshi <j.bhargav.u@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20260719-ti-wkup_m3-v1-1-848a95b401a5@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
I am maintaining phy-zynqmp driver in xilinx tree and would like to
maintain it in the mainline kernel as well. Hence adding myself as a
maintainer.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20260627162233.2803425-1-radhey.shyam.pandey@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current hardware does not support TX VLAN offload for packets with
three or more VLAN tags. When such packets are transmitted with hardware
VLAN offload enabled, the hardware may malfunction or produce corrupted
frames.
Add a check in wx_features_check() to parse the VLAN depth of the
skb. If more than two VLAN tags are detected (including both the
hardware tag and in-band tags), strip NETIF_F_HW_VLAN_CTAG_TX and
NETIF_F_HW_VLAN_STAG_TX from the feature set. This forces the
kernel networking stack to handle VLAN insertion in software for
these specific packets, ensuring correct transmission.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/069DF89AA8029189+20260713060441.276612-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use %pe format specifier instead of %ld with PTR_ERR() to print
error pointers as a symbolic error name (e.g. -ENOMEM) instead
of a raw integer value.
Signed-off-by: Ronan Marchal <ronanmarchal29@gmail.com>
[ rjw: Subject rewrite ]
Link: https://patch.msgid.link/20260615191832.75923-1-ronanmarchal29@gmail.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When build_skb() fails in hip04_rx_poll(), the driver jumps to the
refill path without releasing the current RX buffer and its DMA mapping.
Installing a replacement buffer then overwrites the slot references and
leaks both resources.
Keep the current slot intact and return budget so NAPI retries the same
buffer. Also free a newly allocated RX fragment when dma_map_single()
fails.
This issue was found by an in-house static analysis tool.
Fixes: 701a0fd523 ("hip04_eth: fix missing error handle for build_skb failed")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20260712142729.2057636-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrea Mayer says:
====================
seg6: add FIB table attribute for post-encap SID route lookup
After SRv6 encapsulation the kernel looks up the route for the first SID,
the outer IPv6 destination of the encapsulated packet. This post-encap SID
route lookup uses the FIB table of the current routing context. When the
encap route is installed in a VRF, the VRF's table may not have a route for
the SID, which should be handled by another table, e.g. one used for
underlay connectivity.
A new optional SEG6_IPTUNNEL_TABLE attribute selects the FIB table used for
this lookup. When set by the user, the attribute is honored on both the
input path (traffic that is received, encapsulated and forwarded) and the
output path (traffic that is locally originated and then encapsulated).
SRv6 encap routes that do not set the attribute use the current routing
context, as before.
A companion iproute2 series follows on the mailing list. The examples below
show how to use the "lookup" attribute:
# SID route installed in the underlay table 500
ip -6 route add fc00::100/128 via fd00::1 dev veth0 table 500
# encap route in vrf-100; the first SID is looked up in table 500
ip -6 route add cafe::1/128 vrf vrf-100 \
encap seg6 mode encap segs fc00::100 lookup 500 dev veth0
# or if the SID is already handled by the main table
ip -6 route add cafe::1/128 vrf vrf-100 \
encap seg6 mode encap segs fc00::100 lookup main dev veth0
This work started from a use case raised by Nicolas Dichtel and took shape
in the discussion with him [1]. Thanks Nicolas.
The series is made of two patches. The first implements the attribute. The
second adds an L3 VPN selftest that exercises both the input and the output
path, with the attribute (traffic reaches its destination) and without it
(the packet is dropped).
[1] https://lore.kernel.org/all/20260327140709.959636-1-nicolas.dichtel@6wind.com/T/
====================
Link: https://patch.msgid.link/20260711162907.6521-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a selftest for the SEG6_IPTUNNEL_TABLE attribute, which selects the FIB
table for the post-encap SID route lookup. This looks up the route for the
first SID, the outer destination of the encapsulated packet.
Two routers provide L3 VPN services over an IPv6 underlay. Each router uses
a separate VRF per tenant, with default blackhole routes (IPv4 and IPv6)
that drop unmatched traffic. Tenant traffic is encapsulated, then
decapsulated with an End.DT46.
The encap routes are installed in the tenant VRF, but the routes that match
the first SIDs live in a separate underlay table (500). The "lookup 500"
attribute points the lookup there rather than to the VRF.
The test covers both the input path, where forwarded host traffic triggers
encapsulation, and the output path, where a router originates traffic from
its own loopback inside a VRF.
With the "lookup" attribute, traffic reaches its destination on both paths.
Without it, on the input path the lookup stays in the VRF and hits the
blackhole, and on the output path it falls through to the main table, which
has no matching route.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://patch.msgid.link/20260711162907.6521-3-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After SRv6 encapsulation the kernel looks up the route for the first SID,
that is the outer IPv6 destination of the encapsulated packet. This
post-encap SID route lookup uses the FIB table of the current routing
context. When the encap route is installed in a VRF, the VRF's table may
not have a route matching the SID. In that case another table should
handle it, e.g. one configured for underlay connectivity.
Add an optional SEG6_IPTUNNEL_TABLE attribute that selects the FIB table
used for this lookup. When set by the user, the attribute is honored on
both the input path (forwarded traffic) and the output path (locally
originated traffic). SRv6 encap routes that do not set the attribute use
the current routing context, as before.
For example:
# SID route installed in the underlay table 500
ip -6 route add fc00::100/128 via fd00::1 dev veth0 table 500
# encap route in vrf-100; the first SID is looked up in table 500
ip -6 route add cafe::1/128 vrf vrf-100 \
encap seg6 mode encap segs fc00::100 lookup 500 dev veth0
# or look up the SID in the main table
ip -6 route add cafe::1/128 vrf vrf-100 \
encap seg6 mode encap segs fc00::100 lookup main dev veth0
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260711162907.6521-2-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The devm_request_threaded_irq() now automatically logs detailed error
messages on failure. This eliminates the need for driver-specific
dev_err() calls that previously printed generic messages.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
[ rjw: Subject adjustment ]
Link: https://patch.msgid.link/20260709023048.599150-12-panchuang@vivo.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The devm_request_threaded_irq() now automatically logs detailed error
messages on failure. This eliminates the need for driver-specific
dev_err() calls that previously printed generic messages.
Signed-off-by: Pan Chuang <panchuang@vivo.com>
Link: https://patch.msgid.link/20260709023048.599150-11-panchuang@vivo.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ksmbd_decompress_request() bounds the decompressed size only against
the maximum request size. A compression transform can therefore
produce a buffer smaller than an SMB2 PDU and install it as
conn->request_buf.
The receive path subsequently calls ksmbd_smb_request(), which reads
the protocol ID before the normal SMB2 minimum-size check. If the
decompressed output is too short, that read can access beyond the
request allocation.
Require the decompressed output to contain at least a complete minimum
SMB2 PDU before allocating and installing the replacement request
buffer.
Fixes: a08de24c2b ("ksmbd: negotiate and decode SMB2 compression")
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The receive path applies the minimum SMB2 PDU size check only when
ProtocolId is SMB2_PROTO_NUMBER. A packet carrying
SMB2_TRANSFORM_PROTO_NUM bypasses the check even when the negotiated
dialect does not provide transform handling.
On an SMB 2.1 connection, a short transform packet therefore reaches
init_smb2_rsp_hdr(), which interprets the request as a full SMB2 header
and reads beyond the request allocation. The copied fields can then be
returned to the unauthenticated client.
Compression transforms are converted to ordinary SMB2 messages before
protocol validation. After that conversion, validate ordinary SMB2
requests against SMB2_MIN_SUPPORTED_PDU_SIZE and require encryption
transform requests to contain both a transform header and an SMB2
header. This rejects truncated requests before work allocation.
Fixes: 368ba06881 ("ksmbd: check the validation of pdu_size in ksmbd_conn_handler_loop")
Cc: stable@vger.kernel.org
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-31063
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
In ntlm_authenticate(), destroy_previous_session() is called using a
user pointer resolved from the client-supplied NTLM blob username field
before the NTLMv2 response is validated. An authenticated attacker can
set the NTLM blob username to match a victim account and set
PreviousSessionId to the victim's session ID; destroy_previous_session()
destroys the victim's session while ksmbd_decode_ntlmssp_auth_blob()
subsequently rejects the request with -EPERM.
Move destroy_previous_session() and the prev_id assignment to after
ksmbd_decode_ntlmssp_auth_blob() returns success and use sess->user
rather than the pre-authentication lookup result. This matches the
ordering already used by krb5_authenticate(), where
destroy_previous_session() is called only after
ksmbd_krb5_authenticate() returns success.
Fixes: e2f34481b2 ("cifsd: add server-side procedures for SMB3")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-cifs/20260702155449.3639773-1-james_montgomery@disroot.org/
Signed-off-by: James Montgomery <james_montgomery@disroot.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
set_ntacl_dacl() validates sid.num_subauth before copying an ACE, but
does not verify that the declared ACE size contains all sub-authorities
described by that field. An undersized ACE can therefore be copied
and later make the POSIX ACL deduplication walk inspect data beyond
the copied ACE boundary.
The existing initial bound check is also too small. It only ensures
that the ACE size field is accessible before set_ntacl_dacl() reads
sid.num_subauth farther into the input buffer.
Require enough input for the fixed SID header before accessing
num_subauth, reject ACEs smaller than that header, and skip ACEs
whose declared size cannot contain the complete SID. This makes the
validation consistent with the other ACE walk paths.
Reported-by: LocalHost <localhost.detect@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
check_add_overflow() unconditionally writes the truncated sum into *d
even on overflow, per its contract in include/linux/overflow.h.
The four check_add_overflow() guards in set_posix_acl_entries_dacl()
and set_ntacl_dacl() break out of the ACE-building loops on overflow,
but the truncated *size is then consumed downstream at the end of
set_ntacl_dacl():
pndacl->size = cpu_to_le16(le16_to_cpu(pndacl->size) + size);
This produces an on-wire NT ACL whose pndacl->size under-reports the
bytes actually written by the preceding fill_ace_for_sid()/memcpy()
calls, yielding a malformed ACL that can trigger out-of-bounds reads
when re-parsed by clients or ksmbd itself.
Restore *size to its pre-addition value on each overflow branch (via
`*size -= ace_sz` / `size -= nt_ace_size`) so that after the break,
*size once again holds the cumulative size of the successfully-written
ACEs. The committed ACL is then truncated-but-self-consistent rather
than malformed.
The ksmbd DACL builders are the only check_add_overflow() sites found
where an overflow path breaks out of a loop and the destination value
is consumed afterward. The other nearby break-style cases either
return -EINVAL on overflow (transport_ipc.c) or break without
consuming the overflowed destination value afterward (buildid.c).
Fixes: 299f962c0b ("ksmbd: use check_add_overflow() to prevent u16 DACL size overflow")
Assisted-by: atomcode:glm-5.2
Assisted-by: Codex:gpt-5.5
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
set_ntacl_dacl() can stop copying ACEs before consuming the full input
DACL when size accounting overflows.
When that happens, num_aces reflects only the ACEs that were actually
copied into the output DACL, but set_posix_acl_entries_dacl() still
receives nt_num_aces and uses it to walk the existing ACE array during
dedup.
That makes the dedup walk scan past the copied ACE array and inspect
buffer tail that does not contain valid ACEs.
Split the two meanings currently carried by the NT ACE count. Pass the
number of copied NT ACEs to bound the dedup walk, and preserve the
original "input DACL had NT ACEs" state separately for the
Everyone/default ACL fallback.
This keeps the dedup walk aligned with the ACEs that are actually
present in the rebuilt DACL.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
SMB2_FLAGS_SIGNED is controlled by the incoming request and only indicates
that a signature accompanies that request. Do not use it to decide whether a
signing-required session must authenticate the request.
Reject an unsigned plaintext request before dispatch when the session
requires signing. Continue to validate signatures on signed requests,
including when signing is optional. Encrypted requests have already been
authenticated during decryption.
An OPLOCK_BREAK acknowledgment is a session request and is subject to the
same signing rule, so do not exclude it from signed-request detection.
Reported-by: Charles Vosburgh <trilobyte777@gmail.com>
Tested-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Reviewed-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The VFS initializes a child's POSIX ACL from the parent's default ACL and
the requested creation mode. Do not mutate the parent ACL or overwrite the
child's VFS-computed access and default ACLs afterwards.
This preserves restrictive ACL_MASK entries and prevents SMB object creation
from widening effective permissions.
Reported-by: Charles Vosburgh <trilobyte777@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> says:
I will post Card capsuling patch.
To makes its review easy, adds card_to_mdata() and useit to reduce
un-related diff.
No functional change, but is preparation for cleanup driver.
Link: https://patch.msgid.link/877bmpjfjz.wl-kuninori.morimoto.gx@renesas.com
p1022_rdk.c will be updated when Card capsuling.
To makes its review easy, adds card_to_mdata() and useit to reduce
un-related diff.
No functional change, but is preparation for cleanup driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/874ihtjfj0.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
p1022_ds.c will be updated when Card capsuling.
To makes its review easy, adds card_to_mdata() and useit to reduce
un-related diff.
No functional change, but is preparation for cleanup driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://patch.msgid.link/875x29jfj4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Michael Bommarito says:
====================
amt: fix use-after-free of the skb head across pulls
Several AMT receive and transmit paths cache a pointer into the skb head
and then call a helper that can reallocate that head before the cached
pointer is used again, so the later access reads or writes freed memory.
Patch 1 walks every AMT path and, for each pointer used after a
reallocating call, either snapshots the value before the first pull or
re-derives the pointer after the last one.
Patch 2 is a smaller, separable hardening change: the three handlers
that rewrite the ethernet header do so in place without making the head
private, which corrupts a cloned skb (for example one held by a packet
tap). It adds skb_cow_head() before the rewrite, split out so the
use-after-free fix is not held up by discussion of the clone case.
====================
Link: https://patch.msgid.link/20260711151934.2955226-1-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
amt_multicast_data_handler(), amt_membership_query_handler() and
amt_update_handler() rewrite the ethernet header of the decapsulated skb
in place (eth->h_proto, eth->h_dest and, for the query, also
eth->h_source) before handing it up the stack. The skb head may be
shared, for example when a packet tap has cloned it on the underlay
interface, so writing through it corrupts the other reader's copy.
Call skb_cow_head() before the rewrite so the head is private. It is
placed before the pointers into the head are (re-)derived, so a
reallocation caused by the copy is picked up by those derivations.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20260711151934.2955226-3-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Several AMT receive and transmit paths cache a pointer into the skb head
(ip_hdr(), ipv6_hdr(), eth_hdr() or the AMT message header) and then call
a helper that can reallocate that head before the cached pointer is used
again. pskb_may_pull(), ip_mc_may_pull(), ipv6_mc_may_pull(),
iptunnel_pull_header(), ip_mc_check_igmp() and ipv6_mc_check_mld() can all
free the old head and move the data, so a pointer taken before the call
dangles afterwards and the later access is a use-after-free of the freed
head.
The affected sites are:
amt_rcv() caches ip_hdr() before amt_parse_type() pulls, then reads
iph->saddr.
amt_dev_xmit() caches ip_hdr()/ipv6_hdr() before ip_mc_check_igmp()/
ipv6_mc_check_mld() and pskb_may_pull(), then reads the group address.
amt_multicast_data_handler() caches eth_hdr() before pskb_may_pull(),
then writes the L2 header.
amt_membership_query_handler() caches the AMT header, the outer and
inner eth_hdr() and ip_hdr() before iptunnel_pull_header() and several
pulls, then reads and writes them.
amt_igmpv3_report_handler() and amt_mldv2_report_handler() cache
ip_hdr()/ipv6_hdr() and the current group record and read the record
count from the report header inside the record loop, across the
*_mc_may_pull() calls.
amt_update_handler() caches ip_hdr() and the AMT membership-update
header before pskb_may_pull(), iptunnel_pull_header(),
ip_mc_check_igmp() and the report handler, then reads iph->daddr and
amtmu->nonce / amtmu->response_mac.
Fix each site by either snapshotting the scalar that is used after the
pull before the first pull runs, or re-deriving the header pointer from
the skb after the last pull that can move the head. Values that are
stable across the pull (source and group address, the response MAC and
nonce, the record count, the outer source MAC) are snapshotted; pointers
that are written through or read repeatedly are re-derived.
Fixes: cbc21dc1cf ("amt: add data plane of amt interface")
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Taehee Yoo <ap420073@gmail.com>
Link: https://patch.msgid.link/20260711151934.2955226-2-michael.bommarito@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FS_IOC32_GETVERSION has a distinct compat command encoding. Passing it
through compat_ptr_ioctl() leaves pidfd_ioctl() unable to recognize the
otherwise architecture-independent inode generation query.
Translate the compat command to FS_IOC_GETVERSION before dispatching it
through the native pidfd ioctl implementation.
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20260716052822.1034228-1-me@linux.beauty
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
evaluate_odvp() creates per-ODVP sysfs files before the thermal zone
and later probe resources are registered. The current unwind path only
calls cleanup_odvp() from the late sysfs failure path, so failures after
evaluate_odvp() but before that label, including
thermal_tripless_zone_device_register() failures, leave the ODVP files
and storage behind.
Move the ODVP cleanup to the common ART/TRT unwind path so every failure
after evaluate_odvp() releases the ODVP state. Also clear the cached
ODVP pointers in cleanup_odvp(), because evaluate_odvp() can already call
it for partial setup failures while probe continues.
Fixes: 006f006f1e ("thermal/int340x_thermal: Export OEM vendor variables")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Link: https://patch.msgid.link/20260623015140.19300-1-pengpeng@iscas.ac.cn
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5dae222a5f ("vfs: allow copy_file_range to copy across devices")
allowed filesystems that implement the copy_file_range() f_op to decide
if they want to access cross-sb copy from/to the same fs type.
The same commit added checks to verify same sb copy for filesystems that
implement ->copy_file_range() and do not support cross-sb copy at the
time, namely, to ceph, fuse and nfs.
The two remaining fs which implement ->copy_file_range(), cifs and
overlayfs started to support cross-sb copy from this time.
While overlayfs does support cross-sb copy when the two underlying files
are on the same base fs, the copy operation on the two real files from
two different overalyfs filesystems is performed with the mounter
creds of the destination overlayfs and the read permission access hook
for the source file was called with the wrong creds.
This could cause either deny of access to copy which would otherwise be
allowed (e.g. with splice) or allow read access to file which would
otherwise be denied.
Fix the latter case by explicitly verifying read access to source file
with the source overlayfs mounter creds.
The former case remains a quirk of cross-sb overlayfs copy, but
userspace could fall back to regular copy so no harm done.
Fixes: 5dae222a5f ("vfs: allow copy_file_range to copy across devices")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://patch.msgid.link/20260712122421.203113-1-amir73il@gmail.com
Signed-off-by: Christian Brauner (Amutable) <brauner@kernel.org>
From now on I'll use my own domain for development work, reflect that in
MAINTAINERS and mailmap.
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Natalie Vock <nat@pixelcluster.dev>
Link: https://patch.msgid.link/20260705175305.5589-1-nat@pixelcluster.dev
sof_sdw.c will be updated when Card capsuling.
To makes its review easy, use &pdev->dev instead of card->dev in mc_probe().
There is no diff, because
static int mc_probe(...)
{
...
card->dev = &pdev->dev;
...
}
No functional change, but is preparation for cleanup driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/877bmpi02q.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The hvs and v3d drivers use dev_get_drvdata(master) in their unbind
functions. Since the vc4-drm gets removed before its dependent drivers
(vc4_hvs/vc4_v3d) the vc4_hvs_unbind/vc4_v3d_unbind functions try to
get drvdata of its master and fails with a null dereference error.
Use the data pointer passed to the unbind functions directly instead of
dev_get_drvdata(master). This avoids using potentially freed memory.
Fixes: d3f5168a08 ("drm/vc4: Bind and initialize the V3D engine.")
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Gregor Herburger <gregor.herburger@linutronix.de>
Link: https://patch.msgid.link/20260721-rpi-vc4-fix-v2-1-b813dcd01dc7@linutronix.de
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
The Opto Logic SCX1001511GGC49 is a 10.1" WXGA (1280x800) TFT LCD LVDS
panel.
Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260623195741.495734-3-leoreis.costa@gmail.com
