dcmipp_runtime_resume() can fail while preparing the device clocks, but
dcmipp_resume() currently ignores the result of
pm_runtime_force_resume() and always returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
dcmi_runtime_resume() returns clock enable failures, but dcmi_resume()
currently ignores the result of pm_runtime_force_resume() and always
returns success.
Return the pm_runtime_force_resume() result so system resume does not
hide a failed runtime resume.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
When a device with has_dual_ts=1 is probed and the is_audio_only path
is taken, both dev and dev->dev_next are added to the global
em28xx_devlist via em28xx_init_extension(). However, during disconnect,
em28xx_close_extension(dev) only calls list_del(&dev->devlist), leaving
dev->dev_next->devlist still linked in the global list. When dev_next is
subsequently freed via kref_put(), its devlist entry becomes a dangling
pointer in em28xx_devlist. The next device probe that calls
em28xx_init_extension() triggers a list corruption BUG when list_add_tail
detects the freed node.
This bug was exposed by commit a368ecde8a ("USB: core: Fix duplicate
endpoint bug by clearing reserved bits in the descriptor") which clears
reserved bits in bEndpointAddress during endpoint parsing. This causes
fuzzed endpoint addresses like 0xf3 to be normalized to 0x83, which
em28xx interprets as a vendor audio endpoint, enabling the
is_audio_only + has_dual_ts code path that was previously unreachable
with such descriptors.
Fix this by removing dev->dev_next->devlist from the global list in
em28xx_close_extension() before the device is freed.
Fixes: f410b4093f ("media: em28xx: split up em28xx_dvb_init to reduce stack size")
Cc: stable@vger.kernel.org
Reported-by: syzbot+99d6c66dbbc484f50e1c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=99d6c66dbbc484f50e1c
Signed-off-by: Jiangong.Han <jiangong.han@windriver.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The byte-alignment paths can call CODE_ADD() with a zero bit
length. The macro then shifts an int by name.b, which can be 32
after the preceding bit was flushed.
vti_bitlen() can likewise shift a signed int into its sign bit while
searching for the bit length, and the package mask construction can
shift by the full type width.
Make zero-length additions a no-op, derive the bit length with fls(),
and build the mask with GENMASK().
Signed-off-by: Yousef Alhouseen <alhouseenyousef@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
compress_sliced_buf() scans one byte at a time while testing a four-byte
VBI start code. The final iterations can read beyond the remaining
buffer tail.
Stop the scan once fewer than four bytes remain.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Some pci_device_id arrays already used the PCI_DEVICE macros, others
used named initializers or list initializers. Unify all to use the
PCI_DEVICE macros and (if applicable) a named initializer for
.driver_data. Also drop all zeros that the compiler can care for and
unify indention and spacing.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The existing tegra_vi_graph_build function relies heavily on a one-to-one
match between Device Tree nodes and media pad links. While this works for
simpler configurations, it causes issues when Device Tree nodes do not
match media pad link logic (e.g., mt9m114). Switch to the
media_entity_get_fwnode_pad helper to verify and retrieve the correct pad
linked to an endpoint, rather than assuming the endpoint ID matches the
pad ID.
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # tegra20, parallel camera
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver uses several symbols and structs defined in that header. The
header is currently included transitively via
"vip.h" ->
<media/v4l2-ctrls.h> ->
<media/media-request.h> ->
<media/media-device.h> ->
<linux/platform_device.h>
which seems to be on the lower end of the scale between random and
reliable.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The av7110_start_feed function contains heavily nested if-statements,
causing excessive indentation and violating code style guidelines.
Refactor the logic inside the DMX_MEMORY_FE case by inverting the
conditional check to break early. Additionally, remove the inner
'if (feed->ts_type & TS_DECODER)' check, as it is redundant since
the outer block already validates this condition.
This reduces the indentation level and cleans up redundant checks
without altering the underlying driver behavior.
Signed-off-by: André Moreira <andrem.33333@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
psi_schedule_rtpoll_work() is called locklessly from the scheduler hotpath
and can race psi_trigger_destroy() taking down the last rtpoll trigger under
rtpoll_trigger_lock:
psi_schedule_rtpoll_work() psi_trigger_destroy()
rcu_read_lock();
task = rcu_dereference(rtpoll_task);
rcu_assign_pointer(rtpoll_task, NULL);
timer_delete(&rtpoll_timer);
mod_timer(&rtpoll_timer, ...);
rcu_read_unlock();
synchronize_rcu();
kthread_stop(task_to_destroy);
The group can then be freed with the re-armed timer still pending, and
poll_timer_fn() runs on freed memory.
461daba06b ("psi: eliminate kthread_worker from psi trigger scheduling
mechanism") deleted the timer synchronously after the synchronize_rcu(),
which prevented this but raced trigger creation instead: the deletion could
cancel the timer that a new trigger set armed during the grace period and,
as creation also reinitialized the timer at the time, corrupt it.
8f91efd870 ("psi: Fix race between psi_trigger_create/destroy") moved the
initialization into group_init() and the deletion into the locked section,
trading the creation races for the window above.
Neither placement in the destruction path works. A pending timer firing
while the group is alive is harmless though. poll_timer_fn() just wakes the
rtpoll waitqueue and doesn't re-arm itself. Bind the timer to the group's
lifetime instead and shut it down in psi_cgroup_free(). Nothing can arm it
by then. timer_shutdown_sync() because the timer is never armed again.
Fixes: 8f91efd870 ("psi: Fix race between psi_trigger_create/destroy")
Cc: stable@vger.kernel.org # v5.10+
Reported-by: Sashiko AI <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/all/20260711000434.36C4A1F000E9@smtp.kernel.org/
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Matt Fleming <mfleming@cloudflare.com>
Acked-by: Suren Baghdasaryan <surenb@google.com>
a5b98009f1 ("sched/psi: fix race between file release and pressure write")
made pressure_write() hold cgroup_mutex across psi_trigger_create(), which
forks the psimon kthread for the first rtpoll trigger. As kthread creation
depends on the whole fork path, the commit inadvertently created a lot of
unwanted locking dependencies from cgroup_mutex.
sched_ext got hit by one: its enable path blocks forks and then grabs
cgroup_mutex, so a pressure write racing a scheduler enable deadlocks, with
every other fork piling up behind.
Fix it by splitting trigger creation so that the worker is forked with
cgroup_mutex dropped and the kernfs active reference left broken. The latter
matters because rmdir and cgroup.pressure writes drain active references
under cgroup_mutex. Publishing the trigger last keeps error reporting
synchronous and preserves the of->priv lifetime rules.
The trigger registered in the first stage pins the group's rtpoll machinery
across the unlocked window, leaving only creation races to resolve. The
catch-up poll on installation covers scheduling attempts dropped while there
was no worker.
v2: Retagged sched/psi (was cgroup).
Fixes: a5b98009f1 ("sched/psi: fix race between file release and pressure write")
Cc: stable@vger.kernel.org
Cc: Edward Adam Davis <eadavis@qq.com>
Cc: Chen Ridong <chenridong@huaweicloud.com>
Reported-by: Matt Fleming <mfleming@cloudflare.com>
Closes: https://lore.kernel.org/all/20260710100441.2653477-1-matt@readmodwrite.com/
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Tested-by: Matt Fleming <mfleming@cloudflare.com>
Acked-by: Suren Baghdasaryan <surenb@google.com>
The splitting and merging of kernel page table mappings between small and
large is protected by cpa_lock. The merging is relatively new but the
splitting is ancient.
The splitting has a locking optimization: since DEBUG_PAGEALLOC forces all
mappings to 4k, there are no large pages to split. So the code that *might*
cause a split can just skip the locking (and a few other things).
This is entertaining, but it adds complexity and makes for weird locking
rules. Plus it's all for a debugging feature which makes the kernel super
slow in the first place. Optimizing something which is already super slow
and not used in production is not the best way to spend our complexity
budget.
Stop gating cpa_lock on debug_pagealloc_enabled() to simplify the code
and the locking rules.
[ dhansen: flesh out changelog ]
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://patch.msgid.link/20260715144519.934289-1-rppt@kernel.org
Link: https://lore.kernel.org/all/aab44f08-89f8-47fe-bee4-0ab6b25968c6@intel.com/
cs35l41_get_acpi_mute_state() evaluates a _DSM method to get the ACPI
mute state and reads the first byte from the returned object.
However, the returned ACPI object is owned by the caller and is never
freed after use, so each successful query leaks the _DSM result object.
The code also assumes that the returned object is a buffer with at least
one byte. A malformed firmware response can return a different object
type or an empty buffer, and the direct ret->buffer.pointer dereference
can then access an invalid pointer.
Use the typed _DSM helper, validate that the returned buffer contains at
least one byte, and free the ACPI object after reading it.
Fixes: 447106e92a ("ALSA: hda: cs35l41: Support mute notifications for CS35L41 HDA")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260708113625.752913-1-lgs201920130244@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
fw_log_from_bo() validates the tracing buffer header_size and that the
log fits within the BO, but never checks that log->size is at least
log->header_size. fw_log_print_buffer() then computes:
u32 data_size = log->size - log->header_size;
which underflows to a near-U32_MAX value when firmware reports a log whose
size is smaller than its header. That huge data_size defeats the
log_start/log_end bounds clamps added by commit dd1311bcf0 ("accel/ivpu:
Add bounds checks for firmware log indices"), so fw_log_print_lines() reads
far past the small real data region of the BO. A size of 0 also makes
fw_log_from_bo() advance the offset by 0, causing the callers to loop
forever on the same header.
Reject logs whose size is smaller than the header (which also rejects
size == 0).
Fixes: d4e4257afa ("accel/ivpu: Add firmware tracing support")
Cc: stable@vger.kernel.org
Signed-off-by: Jhonraushan <raushan.jhon@gmail.com>
Reviewed-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@linux.intel.com>
Link: https://patch.msgid.link/20260715074206.867712-1-raushan.jhon@gmail.com
All the information for the mode is now stored within
the subdev state, so configure the sensor based on that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The subdev state is now preferred rather than handling crop
and format within the driver state, so switch the driver to
using it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The sensor supports 2 or 4 lane readout, but the driver only allowed
for 4 lanes. Add 2 lane support.
The clock tree only supports single PLL mode to feed both IOP (MIPI)
and IVT (Pixel array).
2 lane mode supports a MIPI link frequency of up to 445MHz (890Mbit/s)
cf 360MHz (720Mbit/s) for 4lane. Update clock setup and pixel rates to
match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
In preparation for additional options in the PLL setup, compute
the link frequency rather than using a hardcoded value.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This avoids the set_ctrl handler being called under any
circumstances, as it will return an error for the unhandled
ctrl.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The difference between frame length and max exposure time in
lines is 10. That had been used as a bare value in calculations.
Move it to a define, and use that define.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The colorspace fields were left set to 0 when they should be
set appropriately for a raw image sensor. Add those values.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Use the new comon CCI register access helpers to replace the private
register access helpers in the imx355 driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Avoid powering the sensor up and down unnecessarily by using
pm_runtime's autosuspend_delay feature.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Provide all the cropping information via get_selection.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
fll_min (Frame Length Lines) is set to the same value as fll_def
for all modes, which makes it redundant.
The actual value is also erroneous as the sensor works in all
the defined modes with FLL set at the mode height + 20 lines,
so set the vblank control minimum to 20 rather than varying it.
This also improves the maximum frame rate achievable.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The pixel rate is always the same, so there is no need to try and
recompute it in imx355_set_pad_format, and then no need to have the
pointer to it stored.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The link_freq_index value in imx355_mode is unused, so remove it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Compute the binning registers based on the difference between
the mode width/height vs the crop width/height.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The driver already has the LLP value stored in the mode structure,
but also had the same value set via register writes in the mode's
register list. Remove this duplication.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Currently the cropping is set via register entries in the per mode
register lists. Add the crop information to the mode structure as
a v4l2_rect, and set the registers programmatically.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Registers 0x0340 and 0x0341 (FRM_LENGTH_LINES) are already written
from the set_ctrl(V4L2_CID_VBLANK) handler, so don't write them
from the mode register list.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
A large number of registers are identical within all the modes.
Move those to imx355_global_regs.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The sensor supports output over either 2 or 4 CSI2 data
lanes. The binding only permitted the 4 lane configuration.
Add the 2 lane configuration as an option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The IMX355 sensor supports multiple external clock frequencies,
including 19.2 MHz and 24 MHz. The driver currently supports only
fixed 19.2 MHz input clock.
Refactor the clock handling to make the PLL configuration dependent
on the external clock frequency and add support for 24 MHz. Introduce
a table of clock parameter sets and program the corresponding EXTCLK
frequency and PLL multipliers to maintain consistent internal VCO
frequencies across supported inputs.
The PLL settings are adjusted so that OP VCO remains at 720 MHz
This preserves existing timing characteristics while allowing systems
using a 24 MHz clock to operate correctly.
No functional change for existing 19.2 MHz users.
Assisted-by: Claude:claude-opus-4-6
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
If v4l2_async_register_subdev_sensor failed, then the sensor had
already been powered down by pm_runtime_idle, but the error path
then also explicitly called imx355_power_off as well. That left
an imbalance in the regulator and clock calls.
Call pm_runtime_idle only after v4l2_async_register_subdev_sensor
succeeds to avoid this.
Fixes: efa5fe19c0 ("media: imx355: Enable runtime PM before registering async sub-device")
Cc: stable@vger.kernel.org
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Renesas R-Car S4/V4H/V4M GIC600 integration has address width for AXI
or APB interface configured to 32 bit, it can therefore access only
the first 4 GiB of physical address space. This information comes from
R-Car V4H Interface Specification sheet; there is currently no technical
update number assigned to this limitation. Further input from hardware
engineer indicates that this limitation also applies to R-Car S4 and V4M.
Name the limitation GEN4GICITS1, and add a driver quirk to mitigate this
limitation.
The quirk is keyed on the combination of the GIC implementation
and the platform identification in the device tree.
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260707203743.88299-5-marek.vasut+renesas@mailbox.org
The GIC600 implementation is now known to be used on multiple 64-bit
SoCs, where it has address width for AXI or APB interface configured
to 32 bit, and it can access only the first 4GiB of physical address
space.
Rework the handling of the quirk to work around this limitation such
that new entries can be added purely as new compatible strings, with
no need to add additional functions or new its_quirk array entries.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20260707203743.88299-4-marek.vasut+renesas@mailbox.org
When MSI is enabled but the DWC built-in iMSI-RX is not used, MSI must
be handled via the GIC ITS. Configure all controller MSI registers
accordingly.
Set or clear the MSICAP0 MSIE bit and the PCIEINTSTS0EN MSI_CTRL_INT
bit based on the MSI enable state. Set both bits when MSI is enabled.
Clear both bits when MSI is disabled.
When MSI is disabled, or when MSI is enabled together with iMSI-RX,
clear AXIINTCADDR and AXIINTCCONT to disable any pass through of MSI
TLPs onto the AXI bus and further into the GIC ITS translation
registers.
When MSI is enabled and iMSI-RX is not used, program AXIINTCADDR with
the target address of the GIC ITS translation register, and program
AXIINTCCONT to enable MSI TLP pass through onto the AXI bus and into
the GIC ITS. This configuration allows the GIC ITS to handle MSI
instead of the integrated iMSI-RX.
The driver includes linux/irqchip/arm-gic-v3.h which pulls in headers
which are available only on ARM and ARM64, on other architectures the
headers are not present and the driver fails to build. This driver is
used only on ARM64 hardware, so isolate its build only to ARM64 to avoid
build failures on other architectures.
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[mani: commit log and squashed the Kconfig fix:
https://patch.msgid.link/20260714131957.38067-1-marek.vasut+renesas@mailbox.org]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260707203743.88299-3-marek.vasut+renesas@mailbox.org
nonseekable_open() never fails, so the error check is unnecessary.
Remove the dead error handling path.
Signed-off-by: Bui Duc Phuc <phucduc.bui@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
switch_region_table_read() accesses the region table with READ_ONCE()
and is called from the lockless switch_map() IO path. However,
switch_region_table_write() stores to the same array with a plain
assignment. This results in an inconsistent access pattern for a
lockless shared variable and may trigger data race reports.
Use WRITE_ONCE() to pair with the existing READ_ONCE() in
switch_region_table_read().
Cc: stable@vger.kernel.org
Fixes: 99eb1908e6 ("dm switch: factor out switch_region_table_read")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Add support for the PCIe controller present in the EcoNet EN7528 (and
EN751221) SoCs.
The PCIe controllers present in these SoCs support 2.5 GT/s and 5 GT/s data
rates, but 5 GT/s require re-training after link up.
Co-developed-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
[mani: commit log]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260702150704.265282-1-cjd@cjdns.fr
invalidate_cblocks parses cache block numbers with sscanf() and then
stores them in the narrower dm_cblock_t type. Values larger than the
cblock representation are truncated before invalidation, so a request
for one cache block can invalidate a different block.
Checking the parsed value after sscanf() is not sufficient because
sscanf() does not reliably reject values beyond U64_MAX before storing
into the destination. Such inputs can still be converted to a wrapped
u64 value and then pass a later range check.
Split ranges in place and parse each single value or range endpoint
directly with kstrtouint() instead. This rejects malformed values and
values that do not fit in dm_cblock_t before they can be converted to
cblock values. The existing range validation continues to reject empty
or out-of-cache ranges, including the single-value U32_MAX case whose
exclusive end wraps to zero.
Assisted-by: Codex:gpt-5.5-cyber-preview
Signed-off-by: Samuel Moelius <sam.moelius@trailofbits.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Ming-Hung Tsai <mtsai@redhat.com>
Add compatible for MT8189 PCIe Gen3 controller, that is compatible with
the PCIe controller found in MT8192.
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260701-mt8189-dt-bindings-pcie-v1-1-7c7a65087654@collabora.com
Implement the MES gang contex alloc and free heplers.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Michael Chen <michael.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some AMD APU multi-function devices expose an integrated USB xHCI
controller. In some circumstances (such as larger VRAM), the PM core
can resume can fail when the xHCI controller is resuming in parallel
with the GPU/display function.
On affected systems, the xHCI controller can complete pci_pm_resume
and start resuming USB devices while the GPU is still in its much
longer resume path. This race condition leads to USB device resume
failures followed by:
xhci_hcd ...: xHCI host not responding to stop endpoint command
xhci_hcd ...: HC died; cleaning up
Create a device link from any xHCI controller sharing the same PCIe
root port as the APU display function. The link uses DL_FLAG_STATELESS
and DL_FLAG_PM_RUNTIME to ensure the GPU completes its resume before
the xHCI controller begins resuming USB devices.
This device link is done specifically in amdgpu so that if the
platform firmware has been modified such that this issue doesn't happen
the version can be detected and the workaround skipped.
Suggested-by: Aaron Ma <aaron.ma@canonical.com>
Reported-by: mrh@frame.work
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221073
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Alexander F <superveridical@gmail.com>
Tested-by: Francis DB <francisdb@gmail.com>
Link: https://patch.msgid.link/20260713195313.1739762-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN42B enables DML2 and DML21 by default and defines
dcn42b_prepare_mcache_programming(), but the resource function table only
wires the callback when CONFIG_DRM_AMD_DC_DML21 is defined.
There is no in-tree Kconfig symbol named DRM_AMD_DC_DML21, so the
preprocessor always removes the callback entry. Sibling DCN42 and DCN401
resource tables wire their prepare_mcache_programming callbacks
unconditionally, and the core DC code already checks whether the callback
pointer is present before calling it.
Remove the stale guard so DCN42B exposes the callback relation that its
source and DML21 build world already provide.
This is an RFC patch draft from static conditional callback legality
auditing. It needs AMD display maintainer review before submission as a
final fix.
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In dm_update_crtc_state(), the skip_modeset path releases new_stream
via dc_stream_release() but does not set the pointer to NULL.
If a later error (e.g., color management failure) triggers the fail
label, the error path calls dc_stream_release() again on the same
dangling pointer, causing a double release and potential use-after-free.
Fix this by setting new_stream to NULL after the initial release.
Fixes: 9b690ef3c7 ("drm/amd/display: Avoid full modeset when not required")
Signed-off-by: WenTao Liang <vulab@iscas.ac.cn>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
link_dp_irq_handler.c includes "link_dp_panel_replay.h" twice. Drop the
redundant second include; this is a non-functional cleanup flagged by
scripts/checkincludes.pl.
Fixes: 1e5cd4adfc ("drm/amd/display: move panel replay out from edp")
Signed-off-by: Anas Khan <anxkhn28@gmail.com>
Reviewed-by: George Zhang <george.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
