u_audio_start_capture() enables the capture OUT endpoint, queues capture
requests and marks the stream active before setting up the optional
feedback endpoint.
If feedback endpoint configuration or enablement fails, the function
returns an error while the capture endpoint remains enabled and its
requests may remain queued. The current code even leaves TODO comments
at these return paths.
Unwind the already started capture endpoint on these failures. Also set
fb_ep_enabled only after usb_ep_enable() succeeds, so the software state
matches the endpoint state.
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/183621D513E0DE8B+20260611091229.4017443-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A comment in drivers/usb/gadget/legacy/nokia.c incorrectly refers to
CONFIG_USB_DEBUG instead of CONFIG_USB_GADGET_DEBUG_FILES. Correct it.
Discovered while searching for CONFIG_* symbols referenced in code but
not defined in any Kconfig file.
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260613235156.164531-1-enelsonmoore@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdo_epr_avs_apdo_max_voltage_mv() extracts the EPR AVS minimum-voltage
field instead of the maximum-voltage field. As a result, an EPR AVS APDO
with different minimum and maximum voltages is decoded as having
identical limits. The currently visible effect is that
tcpm_log_source_caps() reports a min-min voltage range.
Extract PDO_EPR_AVS_APDO_MAX_VOLT in the maximum-voltage accessor.
Fixes: f82890c98f ("tcpm: Parse and log AVS APDO")
Signed-off-by: Xu Rao <raoxu@uniontech.com>
Link: https://patch.msgid.link/48301FCEC9F3CA14+20260616085439.987664-1-raoxu@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
os_desc_qw_sign_show() passes OS_STRING_QW_SIGN_LEN as the input
length to utf16s_to_utf8s(), but that argument counts UTF-16 code
units while OS_STRING_QW_SIGN_LEN (14) is the byte size of qw_sign[].
The array holds only OS_STRING_QW_SIGN_LEN / 2 (7) code units, so the
conversion reads up to 7 units (14 bytes) past the end of qw_sign[]
into the following members of struct gadget_info when the stored
signature fills the array without a NUL terminator, exposing those
bytes through the configfs attribute.
The store path halves the count for its input bound but passes the
full byte count as the utf8s_to_utf16s() output limit; use the
destination code-unit count in both directions.
Fixes: 76180d716f ("usb: gadget: configfs: make qw_sign attribute symmetric")
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Link: https://patch.msgid.link/20260618005043.1581707-1-michael.bommarito@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the string is read while being updated (which is why the copy is done
in place) and the new string is longer than the old one, then the reader
can read memory that isnt part of either string.
Use memcpy() to copy the known length string instead of strcpy.
Signed-off-by: David Laight <david.laight.linux@gmail.com>
Link: https://patch.msgid.link/20260608095523.2606-37-david.laight.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple KMS helper are deprecated since they only add an intermediate
layer between drivers and the atomic modesetting.
This patch removes the drm_simple_encoder_init() helper usage in the
qxl display driver by open coding it and using the encoder atomic
helpers directly. This is a step to eventually get rid of this simple
KMS helper, once all drivers that use it have been converted.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260707-qxl-simple-v2-1-08d21bc74a41@gmail.com
Currently, FunctionFS exposes each USB endpoint as a separate,
unidirectional file descriptor (e.g., `ep1` for IN, `ep2` for OUT).
While this mirrors the underlying hardware structure, it forces
userspace daemons implementing bidirectional protocols to manage
multiple file descriptors. When dealing with legacy protocols which
require exposing a single, bi-directional fd to userspace, this becomes
problematic.
This patch introduces the `FUNCTIONFS_RW_PROXY_EPS` UAPI flag. When
passed in the descriptor header during initialization, FunctionFS
provisions a "rw_proxy" bidirectional file descriptor (e.g., `ep1_rw`)
alongside every pair of IN/OUT endpoints.
Implementation details:
- RW proxy files act as a pure VFS alias, proxying operations
directly to the base ffs_epfile instances. A `read()` proxies to
the OUT endpoint's file, and a `write()` proxies to the IN file.
- Because operations are proxied natively, they reuse the underlying
base endpoint's lock (`epfile->mutex`) and tracking state. This
serializes concurrent I/O, preventing buffer corruption or races
even if userspace mixes transfers across both the rw_proxy and base files
while allowing full-duplex synchronous operations to occur concurrently
without serializing on a single lock.
- Control operations (like IOCTLs) and intentional stalls (via
reverse-direction I/O) must still be issued on the base endpoints, as the
rw_proxy returns `-ENOTTY` for IOCTLs and cannot trigger stalls.
Assisted-by: Antigravity:gemini-3.1-pro
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-5-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transferring data from a USB gadget to a host, a transfer is
considered complete when the host receives a short packet (a packet
smaller than wMaxPacketSize). If the total transfer length is an
exact multiple of wMaxPacketSize, a Zero-Length Packet (ZLP) must
be appended to signal the end of the transfer.
FunctionFS currently provides no mechanism for userspace to instruct
the kernel to set the `req->zero` flag on transfers. Userspace
workarounds, such as manually submitting separate 0-byte requests,
may not be available for legacy protocols which must maintain write
behavior compatibility when moved to functionfs implementations.
To resolve this, introduce a new ioctl, FUNCTIONFS_ENDPOINT_ENABLE_ZLP,
which takes a pointer to a __u32 flag. When enabled, all subsequent
transfers on that endpoint will have the `req->zero` flag set, allowing
the underlying USB Device Controller (UDC) hardware to automatically
append a ZLP only when mathematically required. For logical transfers
chunked across multiple requests, userspace can dynamically toggle this
flag, enabling it only prior to submitting the final chunk.
The flag defaults to false to maintain backward compatibility. Once
enabled, the state is persistent for the lifetime of the endpoint and
will not be reset by opening or closing the endpoint file descriptors.
Assisted-by: Gemini-CLI:gemini-3.1-pro-preview
Signed-off-by: Neill Kapron <nkapron@google.com>
Link: https://patch.msgid.link/20260619040609.4010746-4-nkapron@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error paths for endpoint-disabled (ESHUTDOWN) and request-allocation
failure (ENOMEM) in ffs_dmabuf_transfer() jump to err_fence_put which
calls dma_fence_put() on the fence. However, at that point the fence has
only been kmalloc'd — dma_fence_init() has not been called yet, so the
refcount and the fence ops are uninitialized. Calling dma_fence_put() on
such an object leads to undefined behavior.
Use kfree() instead, since the fence is just a plain allocation at this
stage, and rename the label to err_fence_free to reflect the actual
cleanup action.
Fixes: 7b07a2a7ca ("usb: gadget: functionfs: Add DMABUF import interface")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patch.msgid.link/20260612-fix-f_fs-fence-cleanup-v1-1-79f489b0efe9@analog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UAC1 and UAC2 configfs rate-list attributes parse a comma-separated
list of sampling rates and store each parsed value in fixed-size arrays.
The arrays have UAC_MAX_RATES entries, but the store paths do not check
that the input contains at most that many tokens before writing through
opts->name##s[i++].
Writing more than ten rates therefore writes past the end of the
p_srates[] or c_srates[] array in struct f_uac1_opts or struct
f_uac2_opts.
With CONFIG_UBSAN_BOUNDS enabled, writing an 11-entry rate list to the
UAC1 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac1.c:1669:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac1_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
The same reproducer against the UAC2 p_srate attribute reports:
UBSAN: array-index-out-of-bounds
drivers/usb/gadget/function/f_uac2.c:2087:1
index 10 is out of range for type 'int [10]'
__ubsan_handle_out_of_bounds.cold
f_uac2_opts_p_srate_store
configfs_write_iter
vfs_write
ksys_write
do_syscall_64
Reject additional tokens once UAC_MAX_RATES entries have been parsed.
Also keep the original kstrdup() pointer for kfree(), because strsep()
advances the parsing cursor. Freeing the advanced cursor leaks the
original buffer on successful parses and can free an interior pointer on
some error paths.
Fixes: 695d39ffc2 ("usb: gadget: f_uac1: Support multiple sampling rates")
Fixes: a7339e4f57 ("usb: gadget: f_uac2: Support multiple sampling rates")
Signed-off-by: Qing Ming <a0yami@mailbox.org>
Link: https://patch.msgid.link/20260519143319.147494-1-a0yami@mailbox.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three USB controllers on mt8196, each controller's wakeup
control is different, add some specific versions for them.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://patch.msgid.link/20260413121727.4702-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three USB controllers on mt8196, each controller's wakeup
control is different, add some specific versions for them, and add
compatilbe for mt8196.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://patch.msgid.link/20260413121727.4702-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a new UPIO_BUS I/O type, use it to register our serial
port. This allows the driver to work properly when using DT where
membase/iobase are not set.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-10-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a new UPIO_BUS I/O type, use it to register our serial
port and remove obscure membase/iobase workaround.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-9-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a new UPIO_BUS I/O type, use it to register our serial
port and remove ambiguous membase/iobase workaround.
Note that commit 5da6b1c079 ("sc16is7xx: Set iobase to device index")
used the iobase field as an index within the device to allow infering
the order through sysfs, but this is no longer needed since
commit 1ef2c2df11 ("serial: core: Fix serial core controller port name
to show controller id").
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-8-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I2C/SPI serial drivers don't use the following struct uart_port variables:
port->membase
port->mapbase
port->iobase
However, they are forced to set membase to a non-zero value so that
uart_configure_port() will succeed because of the following check:
/* If there isn't a port here, don't do anything further. */
if (!port->iobase && !port->mapbase && !port->membase)
return;
Add a new I/O type for SPI and I2C bus devices to remove the need to
implement the kind of above-mentioned ambiguous workarounds to make them
work. Now that UART report functions are using uart_iotype_*() functions,
no more irrelevant I/O information are being printed for UPIO_BUS iotypes.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-7-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of new functions uart_iotype_mmio() and uart_iotype_legacy_io()
to simplify and improve code readability, as well as avoid some variables
init if the iotype is not valid.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-6-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of new functions uart_iotype_mmio() and uart_iotype_legacy_io()
to simplify and improve code readability.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-5-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uniformize serial port I/O infos display from three different functions
that display mostly the same information, but with some variations, by
adding a common function.
This make use of new functions uart_iotype_mmio() and
uart_iotype_legacy_io() to simplify and improve code readability.
This will prevent displaying irrelevant information for future IO types
(ex: UPIO_BUS), while also addressing the (eventually) invalid check for
"iotype >= UPIO_MEM".
This also allows us to remove the confusing cast to (unsigned long long)
for iobase which is defined as an unsigned long, and use %pa to display the
mapbase pointer, as it is done in earlycon_print_info().
Replace snprintf with more robust scnprintf so we could perhaps one day get
rid of snprintf() entirely.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-4-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of new functions uart_iotype_mmio() and uart_iotype_legacy_io()
to simplify and improve code readability.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-3-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the entire hub6 related match port check into its own function in
8250_hub6.c and add a stub for the case when hub6 code is not even built
into kernel.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://patch.msgid.link/20260521-tty-upio-v3-1-bf74567994a0@dimonoff.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
recv_dless_read() receives a P_DATA_REPLY from a peer into the bio of an
outstanding read request. The peer-supplied payload length reaches it as
the signed int data_size, and two peer-controlled inputs can make it
negative. With a negotiated data-integrity-alg the digest length is
subtracted first, so a reply whose payload is smaller than the digest
underflows data_size. With no integrity algorithm (the default) data_size
is assigned from the unsigned h95/h100 wire length and drbdd() never
bounds it for a payload-carrying command, so a length above INT_MAX casts
it negative; this path needs no non-default feature. The bio receive loop
then computes expect = min_t(int, data_size, bv_len), which is negative,
and drbd_recv_all_warn(mapped, expect) receives with a size_t of SIZE_MAX
into the first mapped page.
The sibling receive path read_in_block() is not affected: it uses an
unsigned size and rejects it against DRBD_MAX_BIO_SIZE before receiving.
Reject a data reply whose size is negative after the optional digest
subtraction, covering both triggers.
Impact: a malicious or man-in-the-middle DRBD peer copies attacker-chosen
bytes past a bio page in the receiver, corrupting kernel memory. A node
that reads from its peer (a diskless node, or read-balancing to the peer)
is exposed in the default configuration; data-integrity-alg is not
required.
Fixes: b411b3637f ("The DRBD driver")
Cc: stable@vger.kernel.org
Assisted-by: Codex:gpt-5-5-xhigh
Assisted-by: Claude:claude-opus-4-8
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://patch.msgid.link/20260710022837.3738461-1-michael.bommarito@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If no_console_suspend is specified, on suspend the 8250 console driver
uses a scratch register (UART_SCR) to store a special canary value. This
is used during the resume path to identify a printk() call before the
driver's own ->resume() callback. In this case,
serial8250_console_restore() is called to quickly re-init the 8250 for
console printing.
See commit 4516d50aab ("serial: 8250: Use canary to restart console after
suspend") for the original motivation.
Unfortunately, this canary workaround does not work in all cases (such as
suspend to mem) because the scratch register will not reset. This has not
been a real issue until now because it could simply lead to some garbage
characters upon resume. However, with the introduction of console flow
control it becomes a real problem because a failed suspend/resume detection
when flow control is enabled leads to all characters hitting the flow
control timeout.
Workaround this issue by temporarily ignoring console flow control when
the debug canary suspend/resume detection is active.
Fixes: 5e6dfb87b1 ("serial: 8250: Add support for console flow control")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://patch.msgid.link/20260707141032.5074-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In accordance with Errata (specification updates)
HSUART May Stop Functioning when DMA is Active.
- Denverton document #572409, rev 3.4, DNV60
- Ice Lake Xeon D document #714070, ICXD65
- Snowridge document #731931, SNR44
For a quick fix just disable the respective callbacks during the device probe.
Depending on the future development we might remove them completely.
Reported-by: micas-opensource <zjianan156@gmail.com>
Closes: https://lore.kernel.org/linux-serial/20250625031409.2404219-1-opensource@ruijie.com.cn/
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260626094937.561776-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On AM33xx RX DMA only triggers when the FIFO reaches the
configured threshold (typically 48 bytes). For smaller bursts
no DMA request is issued and the FIFO is drained by RX timeout.
In this case __dma_rx_do_complete() can legitimately see count == 0.
The current code exits early in this case and does not clear
dma->rx_running, leaving the DMA state inconsistent. This can
prevent RX DMA from restarting and may cause
omap_8250_rx_dma_flush() to fail, marking DMA as broken.
Fix this by clearing dma->rx_running once the DMA transfer has
completed or been terminated, even if no data was transferred.
Fixes: a5fd8945a4 ("serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done")
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Feser <mfe@KBSgmbhfr.onmicrosoft.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/BE3P281MB55155F2F5795E411F5A65282EE0B2@BE3P281MB5515.DEUP281.PROD.OUTLOOK.COM
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
csi_modifier_param() builds the xterm modifier parameter from
shift_state, counting KG_SHIFTL/KG_SHIFTR as Shift, KG_ALTGR as Alt
and KG_CTRLL/KG_CTRLR as Ctrl in addition to the canonical KG_SHIFT,
KG_ALT and KG_CTRL.
That is wrong when those weights are not plain modifiers. Keymaps
derived from XKB layouts (by kbd's xkbsupport, and by the
console-setup used in Debian, Ubuntu and others) encode the active
layout group using KG_SHIFTL/KG_SHIFTR:
group 1: -
group 2: shiftl
group 3: shiftr
group 4: shiftl | shiftr
So while a non-default layout group is selected, KG_SHIFTL and/or
KG_SHIFTR are set in shift_state with no Shift key held.
csi_modifier_param() then adds a spurious Shift to every cursor and
CSI key: pressing Up while group 2 is active emits ESC[1;2A (Shift+Up)
instead of ESC[A. KG_ALTGR has the same problem since it is the
standard third-level selector.
Normal keymaps bind the physical Shift/Ctrl/Alt keys to KG_SHIFT,
KG_CTRL and KG_ALT, leaving the left/right and AltGr weights free for
layout and level selection. Count only those canonical weights, so
genuine modifiers are still encoded while layout/level selectors are
not.
Fixes: 4af70f1516 ("vt: add modifier support to cursor keys")
Reported-by: Alexey Gladkov <legion@kernel.org>
Closes: https://lore.kernel.org/kbd/aj2gR0Y7sM6i9s2G@example.org/
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Link: https://patch.msgid.link/20260626024833.3419086-1-nico@fluxnic.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently relies on qcom_geni_serial_pm() through the
uart_ops.pm callback to manage runtime PM references. However, the
callback has a void return type, so failures from
pm_runtime_resume_and_get() cannot be propagated to the caller.
As a result, startup() may continue and access hardware even when the
runtime PM resume operation failed, leading to register accesses while
the device is not powered.
Move runtime PM acquisition to qcom_geni_serial_startup() and release it
to qcom_geni_serial_shutdown(). Since startup() can return an error, PM
resume failures are now detected and propagated before any hardware
initialization is performed. The startup/shutdown pair also provides a
natural place to balance runtime PM references for normal port usage.
During probe, uart_add_one_port() may configure the port before any user
opens the TTY, meaning startup() has not yet been called. To keep the
hardware powered during port registration, wrap uart_add_one_port() with
PM_RUNTIME_ACQUIRE_IF_ENABLED() and PM_RUNTIME_ACQUIRE_ERR(). This
ensures the device is resumed for the duration of registration and that
the runtime PM reference is automatically released afterwards.
By moving runtime PM handling out of uart_ops.pm, resume failures are no
longer silently ignored and all hardware accesses are guaranteed to
occur while the device is powered.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260710-remove_uart_change_state-v1-1-8e8468da22a1@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike modern SoCs that just work in both big-endian and little-endian
mode using the readl()/writel() or readb()/writeb() accessors, the
internal registers on ixp4xx behave like native-endian 32-bit registers
in both modes, which requires adjusting the register address
when using 8-bit access.
The existing dts files are written for big-endian kernels and 8-bit
access, which does not work with little-endian kernels.
Add a quirk that makes the 8250 OF driver:
1. Mask off any hardcoded offset.
2. Add the += 3 offset if and only if we are running on big endian.
This should work in all combinations of big-endian and little-endian
kernels with either variant of the DTS file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[linusw@kernel.org: Modified to just play with the offset]
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260709-ixp4xx-serial-hackfix-v2-1-465fc8e4c54c@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcom GENI serial DMA TX completion path advances the transmit fifo by
the number of bytes recorded in port->tx_remaining.
If uart_flush_buffer() runs after the hardware has completed a DMA
transfer but before the DMA completion interrupt has been handled, the
serial core resets the transmit fifo while port->tx_remaining still
describes the old DMA transfer.
A previous fix avoided advancing an empty fifo by checking that the fifo
length is at least tx_remaining. That still does not distinguish the old
DMA payload from new bytes written after the flush. If userspace writes
new data before the stale DMA completion interrupt is handled, the fifo
can again contain at least tx_remaining bytes and the stale completion
can advance and discard those new bytes.
Mark an in-flight DMA transfer stale when the transmit fifo is flushed.
The later completion still unprepares the original DMA mapping using the
saved length, but it no longer advances the transmit fifo.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com>
Link: https://patch.msgid.link/20260708131726.768692-1-lgs201920130244@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system power-off, systemd closes the console UART and blocks in
tty_wait_until_sent() waiting for pending TX completion before
uart_shutdown() can cancel pending TX operations. With the default
closing_wait of 30s, this causes a watchdog reset when systemd is
responsible for watchdog feeding.
Set closing_wait to ASYNC_CLOSING_WAIT_NONE in startup() for console
ports to bypass tty_wait_until_sent() on close, allowing uart_shutdown()
to cancel TX commands cleanly. This change doesn't impact regular ports
functionality.
Signed-off-by: Aniket Randive <aniket.randive@oss.qualcomm.com>
Link: https://patch.msgid.link/20260706093749.836121-1-aniket.randive@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system sleep the hardware resources (clocks, interconnect) are
not gated because the runtime-suspend callback is never invoked from
the system sleep path. This prevents the platform from reaching its
lowest idle state.
The system sleep callbacks qcom_geni_serial_suspend() and
qcom_geni_serial_resume() rely solely on uart_suspend_port() /
uart_resume_port() to manage power. uart_suspend_port() drives the
UART PM state machine to UART_PM_STATE_OFF, which in turn calls
pm_runtime_put_sync() and eventually the runtime-suspend callback.
However, if the runtime-PM usage count is still elevated at the time
of system sleep (e.g. the port is held active by an open file
descriptor), the runtime-suspend callback is never invoked and the
hardware resources (clocks, interconnect) remain enabled across
suspend, preventing the platform from reaching its lowest idle state.
Fix this by calling pm_runtime_force_suspend() at the end of
qcom_geni_serial_suspend() so that the runtime-suspend callback is
always executed regardless of the usage count, and by calling
pm_runtime_force_resume() at the start of qcom_geni_serial_resume()
to restore those resources before uart_resume_port() re-opens the
port.
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260702-add_force_suspend_resume_to_system_sleep_callbacks-v2-1-b79e254a7015@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni_se_rx_dma_prep() calls dma_map_single() which can trigger IOMMU
page table allocations under GFP_KERNEL. This is unsafe when called
from qcom_geni_serial_start_rx_dma(), which runs in atomic context
producing a "sleeping function called from invalid context" splat:
__might_resched+0x15c/0x17c
__alloc_pages_noprof+0xe4/0x4c8
qcom_io_pgtable_alloc_page+0x100/0x250
__arm_lpae_map+0x2d0/0x870
geni_se_rx_dma_prep+0xd8/0x158
qcom_geni_serial_start_rx_dma+0x84/0x16c
qcom_geni_serial_startup+0x70/0x104
Fix this by mapping the RX DMA buffer once during probe, where sleeping
is allowed, and keeping it mapped for the lifetime of the device.
Replace the geni_se_rx_dma_prep() / geni_se_rx_dma_unprep() calls in
the runtime paths with dma_sync_single_for_device() before initiating a
transfer and dma_sync_single_for_cpu() on completion, using the persistent
mapping. The buffer is unmapped in probe's error path and in remove().
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
Link: https://patch.msgid.link/20260701-fix-sleep-in-atomic-context-during-rx-dma-setup-v1-1-95c208380c65@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USE_OF is already selected by ARM (unless ARCH_FOOTBRIDGE || ARCH_RPC ||
ARCH_SA1100; these all conflict with ARCH_MULTI_V5). So there is no need
for an explicit select and it can be dropped.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20260705085000.3510576-2-u.kleine-koenig@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ma35d1serial_console_init_port() stores matching UART device nodes in
ma35d1serial_uart_nodes[] with an extra of_node_get() so that console
setup can later read the "reg" property. However, the stored references
are never released after console setup has finished using them.
Drop the stored node reference after ma35d1serial_console_setup() reads
the "reg" property, and clear the array slot to avoid leaving a stale
pointer behind. Also release the iterator reference before breaking out
of for_each_matching_node(), since the normal iterator advance will not
run in that path.
Fixes: 930cbf92db ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Signed-off-by: Yuho Choi <dbgh9129@gmail.com>
Link: https://patch.msgid.link/20260630214043.1887351-1-dbgh9129@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These changes fix an invalid compatible string combination for GPC DMA
on Tegra264, change the compatible string for the CPU found on Tegra234
and update the unit-address of CPU#1 on Tegra264 so it matches the value
in the "reg" property.
-----BEGIN PGP SIGNATURE-----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=tXiU
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmpQ6PkACgkQmmx57+YA
GNkvohAAnHAR/1i3JJOhPJlocRLnci24zt04W/F3+v+qjIxyaNITslbuJz4myHpt
18PjEpPEu1jCdkOVczvLmzXf1b0ZOZ03hbSJ5AHp17IZrpwKy1fK3TUsW97O+Xzz
Duwq7Imbt3lf1yOsu4qCwhzDqVseENEhxmuIBvY0C89PiXd3w9oJGIbp9b8oV5eM
cXVn6X1vgxKxee8SkclLs4AI0uQLir/9gkHn6BbNJ3lJRmWUhcHpUXLBhyfY2n7Q
3Colhzl/Iyyn68en+rdkWXhXHLX267Ht8f4TXVRSV86vXTBKgf/HZHEdzriZus2x
YY9+68SuS/wOjrwLg9PoRbsyg44MDrJS1HE51j+pbRZtZmMoThpzWctNkIDNLOLN
go2yYtxdqz0rYdH0yVwOOzQhmTlYVAlmyA9fUOE1zVsce3GD5XlsWycCKm8Rki+L
tg5oIv9lDDzuwNB5aSE9MwT43BGT5sUri0b7Mj8xdVoP1FOzhc75+TUTxwwPWNaQ
vvvYQdle73Xv4ilKK8VVGxf7d55FULHeyMh/FEzPg3NSgFfH6ElKsfghQg8bkAKm
G7FDr0+PDEudEIDt5mKxlPm4u4h4IfQ6UVGZM5BJDwmcm7y9cPFWFn0E1/QmuPD4
iWTvs2dDUSWlLcSkxI87Yw0cOMeLIWZXZVN9TdHPQu4OrCGwq4g=
=FuhI
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-7.2-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v7.2
These changes fix an invalid compatible string combination for GPC DMA
on Tegra264, change the compatible string for the CPU found on Tegra234
and update the unit-address of CPU#1 on Tegra264 so it matches the value
in the "reg" property.
* tag 'tegra-for-7.2-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix CPU1 node unit-address on Tegra264
arm64: tegra: Fix CPU compatible string to cortex-a78ae on Tegra234
arm64: tegra: Remove fallback compatible for GPCDMA
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While being less compact, using named initializers allows to more easily
see which members of the structs are assigned which value without having
to lookup the declaration of the struct. And it's also more robust
against changes to the struct definition.
The mentioned robustness is relevant for a planned change to struct
pnp_device_id that replaces .driver_data by an anonymous union.
This patch doesn't modify the compiled array, only their representation
in source form benefits. The former was confirmed with x86 and arm64
builds.
Also simplify the list terminator and use a consistent and more common
indention.
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20260629170409.3412413-2-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do unneeded "double free" (emptying an empty list) in one case.
This is not a critical issue at all, the fix just makes code robust
against any possible future changes in the flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260617092515.2649521-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing strcpy() with strscpy() ensures that overflow of the target
buffer cannot happen.
Signed-off-by: David Laight <david.laight.linux@gmail.com>
Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org>
Link: https://patch.msgid.link/20260608095523.2606-10-david.laight.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check for pci_get_slot() to prevent a potetial
null pointer dereference in pch_request_dma().
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260623140539.2272473-1-haoxiang_li2024@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error counter "v->corrupted_errs" was not atomic, thus it could be
subject to race conditions. The call to
dm_audit_log_target("max-corrupted-errors") may be skipped due to the
races.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Assisted-by: Claude:claude-opus-4.6
Fixes: 65ff5b7ddf ("dm verity: add error handling modes for corrupted blocks")
Cc: stable@vger.kernel.org
Log when the BlueField-3 eMMC hardware reset path is invoked.
This makes it easier to diagnose cases where the controller recovery path
depends on issuing an eMMC reset, and helps confirm that the reset sequence
was attempted on affected systems.
Signed-off-by: Satyansh Shukla <satyansh.shukla@oracle.com>
Signed-off-by: Ulf Hansson <ulfh@kernel.org>
The prefix "DM_VERITY_ERR_BLOCK_NR" is 22 chars. Add '=', one digit for
type, ',', up to 20 digits for a u64 block number, and a NUL terminator:
that's 46 bytes. The buffer is 42 bytes. For block numbers >= 16 decimal
digits (devices larger than ~16 EB with 4K blocks), snprintf silently
truncates the uevent environment variable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Assisted-by: Claude:claude-opus-4.6
Fixes: 65ff5b7ddf ("dm verity: add error handling modes for corrupted blocks")
Cc: stable@vger.kernel.org
Fix a possible NULL pointer dereference dm_verity_loadpin_is_bdev_trusted
if the device has no table.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Assisted-by: Claude:claude-opus-4-6
Fixes: b6c1c5745c ("dm: Add verity helpers for LoadPin")
Cc: stable@vger.kernel.org
verity_parse_opt_args is called twice, first with the only_modifier_opts,
first with only_modifier_opts == true and then with only_modifier_opts ==
false. Thus, the static branch &use_bh_wq_enabled was incremented twice
and the destructor verity_dtr would only decrement it once.
Fix tihs bug by only incrementing it on the first call, on the second
call, when v->use_bh_wq is true, do nothing.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Assisted-by: Claude:claude-opus-4-6
Cc: stable@vger.kernel.org
Fixes: df326e7a06 ("dm verity: allow optional args to alter primary args handling")
