The parent clock of the OCP_ABE_ICLK is the AESS_FCLK and the
parent clock of the AESS_FCLK is the ABE_FCLK...
ABE_FCLK --> AESS_FCLK --> OCP_ABE_ICLK
The AESS_FCLK and OCP_ABE_ICLK clocks both have dividers which
determine their operational frequency. However, the dividers for
the AESS_FCLK and OCP_ABE_ICLK are controlled via a single bit,
which is the CM1_ABE_AESS_CLKCTRL[24] bit. When this bit is set to
0, the AESS_FCLK divider is 1 and the OCP_ABE_ICLK divider is 2.
Similarly, when this bit is set to 1, the AESS_FCLK divider is 2
and the OCP_ABE_ICLK is 1.
The above relationship between the AESS_FCLK and OCP_ABE_ICLK
dividers ensure that the OCP_ABE_ICLK clock is always half the
frequency of the ABE_CLK...
OCP_ABE_ICLK = ABE_FCLK/2
The divider for the OCP_ABE_ICLK is currently missing so add a
divider that will ensure the OCP_ABE_ICLK frequency is always half
the ABE_FCLK frequency.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4460 specific clocks are not getting added as the
cpu_is_omap44xx is choosing only OMAP4430 specific clock nodes.
Changing it to add to OMAP4460 specific clocks also.
This is clocks are required of temperature sensor.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Cc: paul@pwsan.com
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This is a continuation of Mike Turquette's patch "OMAP3+: use
DPLL's round_rate when setting rate".
omap3_noncore_dpll_set_rate() and omap3_noncore_dpll_enable() call
omap2_get_dpll_rate() explicitly. It may be necessary for some
DPLLs to use a different function and so use the DPLLs recalc()
function pointer instead.
An example is the DPLL_ABE on OMAP4 which can have a 4X multiplier
in addition to the usual MN multipler and dividers and therefore
uses a different round_rate and recalc function.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Cc: Mike Turquette <mturquette@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
[paul@pwsan.com: merged this patch with Mike's "use clock's recalc in DPLL
handling" patch; also reported by Misael]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The rounded rate can differ from target rate, so to better reflect
reality set clk->rate equal to the rounded rate when setting DPLL frequency.
This avoids issues where the DPLL frequency is slightly different than what
debugfs clock tree reports using the old target rate.
An example of a clock that requires this is DPLL_ABE on OMAP4 which
can have a 4x multiplier on top of the usual MN dividers depending on
register settings. This requires a special round_rate function that
might yield a rate different from the initial target.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap3_noncore_dpll_set_rate uses omap2_dpll_round_rate explicitly. Instead
use the struct clk pointer's round_rate function to allow for DPLL's with
special needs.
An example of a clock that requires this is DPLL_ABE on OMAP4 which
can have a 4x multiplier on top of the usual MN dividers depending on
register settings. This requires a special round_rate function that
might yield a rate different from the initial target.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: split rate assignment portion into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler
and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN
bit in CKGEN module of CM1. From the OMAP4 TRM:
Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only
applicable to DPLL_ABE).
Add new round_rate() and recalc() functions for OMAP4, that check the
setting of REGM4XEN bit and handle this appropriately. The new functions
are a simple wrapper on top of the existing omap2_dpll_round_rate() and
omap2_dpll_get_rate() functions to handle the REGM4XEN bit.
The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so
only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and
omap4_dpll_regm4xen_recalc() functions.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed attempt to return a negative from a fn returning
unsigned; pass along errors from omap2_dpll_round_rate();
added documentation; added Jon's S-o-b]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This change is meant to combine all of the TX flags fields into one u32
flags field so that it can be stored into the tx_buffer_info structure.
This includes the time stamp flag as well as mapped_as_page flag info.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup the protocol handling in the transmit path
so that it correctly offloads software VLAN tagged frames.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the readability of the driver by separating
out the cmd_type configuration and the olinfo configuration into their own
functions. By doing this it is much easier to determine which ingredients
go into setting up these to portions of the descriptor.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change converts two tx_buffer_info index values into pointers. The
advantage to this is that we reduce unnecessary computations and in the case
of next_to_watch we get an added bonus of the value being able to provide
additional information as a NULL value indicates it is unset versus a 0 not
having any meaning for the index value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to simplify the transmit path by reducing the overhead
for creating a transmit context descriptor. The current implementation is
split with igb_tso and igb_tx_csum doing two separate implementations on
how to setup the tx_buffer_info structure and the tx_desc. By combining
them it is possible to reduce code and simplify things since now only one
function will create context descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to be able to improve the performance of the TX path it has been
necessary to add addition info to the tx_buffer_info structure. However a
side effect is that the structure has gotten larger and this in turn has
also increased the size of the RX buffer info structure. In order to avoid
this in the future I am splitting the single buffer_info structure into two
separate ones and instead I will join them by making the buffer_info
pointer in the ring a union of the two.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is to make the NAPI budget limits for transmit
adjustable. Currently they are only set to 128, and when
the changes/improvements to NAPI occur to allow for adjustability,
it would be possible to tune the value for optimal
performance with applications such as routing.
v2: remove tie between NAPI and interrupt moderation
fix work limit define name (s/IXGBE/IGB/)
Update patch description to better reflect patch
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
When short packets are received with jumbos enabled on 82579, they can be
interpreted to have a receive address that does not match any configured
address. This is due to a hardware bug that can be worked around by
reducing the number of IPG octets added when the packet is transferred from
the PHY to the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000 driver when running with lockdep could run into
some possible deadlocks between the work items acquiring
rtnl and the rtnl lock being acquired before work items
were cancelled.
Use a private mutex to make sure lock ordering isn't violated.
The private mutex is only used to protect areas not generally
covered by the rtnl lock already.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the previous commit, there are several functions
that are only ever called from thread context, and are
able to sleep with msleep instead of mdelay.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Thomas Gleixner (tglx) reported that e1000 was delaying for many milliseconds
(using mdelay) from inside timer/interrupt context. None of these paths are
performance critical and can be moved into threads/work items. This patch
implements the work items and the next patch changes the mdelays to msleeps.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version string to better match pair up with the out of tree
driver that contains the same functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
p2p packets should go out only with OFDM rates.
Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).
Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There was an error path that skipped the free_irq() step by mistake.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the L1 D-Cache is in write shadow mode the HW will auto-recover the
error. However we might still log the error and cause a machine check
(if L1CSR0[CPE] - Cache error checking enable). We should only treat
the non-write shadow case as non-recoverable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already have cpu a005 errata handler when instruction cannot be
recognized. Before we lookup the inst, there's type checking, and we also
need to handle it in errata handler when the type checking failed.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If CONFIG_PHYS_ADDR_T_64BIT is set, compilation of sbc8560 fails with
the following error:
arch/powerpc/platforms/85xx/sbc8560.c: In function ‘sbc8560_bdrstcr_init’:
arch/powerpc/platforms/85xx/sbc8560.c:286: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’
Fix that by using %pR format instead of just printing the start of
resource.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When md assembles a RAID0 array it prints out lots of info which
is really just for debugging, so convert that to pr_debug.
It also prints out the resulting configuration which could be
interesting, so keep that as 'printk' but tidy it up a bit.
Signed-off-by: NeilBrown <neilb@suse.de>
When normal-write and sync-read/write bio completes, we should
find out the disk number the bio belongs to. Factor those common
code out to a separate function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In the 'abort' branch of run(), 'conf' cannot possibly be NULL,
so remove the test.
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There wasn't much and it is inconsistent.
Also rearrange fields to keep related fields together.
Reported-by: Aapo Laine <aapo.laine@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
ad7879-i2c.c: warning: 'ad7879_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
synaptics_i2c.c: warning: 'synaptics_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes GCC is not smart enough to recognize that x, y and z are
always used properly initialized in mma8450_poll(). Let's rearrange
the code a bit to help GCC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs attribute show methods are always passed a buffer of length
PAGE_SIZE. To keep from overwriting this buffer and causing havoc, use
snprintf() to guarantee we never write more than the buffer can hold.
In addition, at least for my touchscreen, the number and size of objects
was far too big to fit in a single 4K page. Therefore, this patch also
trims some redundant framing text to leave more room for actual data.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://github.com/davem330/net:
net: fix typos in Documentation/networking/scaling.txt
bridge: leave carrier on for empty bridge
netfilter: Use proper rwlock init function
tcp: properly update lost_cnt_hint during shifting
tcp: properly handle md5sig_pool references
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762cfb ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.
Since commit 3e3da00c01 ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
HDA Intel 0000:20:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
HDA Intel 0000:20:01.0: setting latency timer to 64
BUG: unable to handle kernel paging request at ffffc90011c08000
IP: [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
PGD 13781a067 PUD 13781b067 PMD 1300ba067 PTE 800000fd00000173
Oops: 0009 [#1] SMP
last sysfs file: /sys/module/snd_pcm/initstate
CPU 0
Modules linked in: snd_hda_intel(+) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event tpm_tis tpm snd_seq tpm_bios psmouse parport_pc snd_timer snd_seq_device parport processor evdev snd i2c_viapro thermal_sys amd64_edac_mod k8temp i2c_core soundcore shpchp pcspkr serio_raw asus_atk0110 pci_hotplug edac_core button snd_page_alloc edac_mce_amd ext3 jbd mbcache sha256_generic cryptd aes_x86_64 aes_generic cbc dm_crypt dm_mod raid1 md_mod usbhid hid sg sd_mod crc_t10dif sr_mod cdrom ata_generic uhci_hcd sata_via pata_via libata ehci_hcd usbcore scsi_mod via_rhine mii nls_base [last unloaded: scsi_wait_scan]
Pid: 1153, comm: work_for_cpu Not tainted 2.6.37-1-amd64 #1 M2V-MX SE/System Product Name
RIP: 0010:[<ffffffffa0578402>] [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
RSP: 0018:ffff88013153fe50 EFLAGS: 00010286
RAX: ffffc90011c08000 RBX: ffff88013029ec00 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
RBP: ffff88013341d000 R08: 0000000000000000 R09: 0000000000000040
R10: 0000000000000286 R11: 0000000000003731 R12: ffff88013029c400
R13: 0000000000000000 R14: 0000000000000000 R15: ffff88013341d090
FS: 0000000000000000(0000) GS:ffff8800bfc00000(0000) knlGS:00000000f7610ab0
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffc90011c08000 CR3: 0000000132f57000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process work_for_cpu (pid: 1153, threadinfo ffff88013153e000, task ffff8801303c86c0)
Stack:
0000000000000005 ffffffff8123ad65 00000000000136c0 ffff88013029c400
ffff8801303c8998 ffff88013341d000 ffff88013341d090 ffff8801322d9dc8
ffff88013341d208 0000000000000000 0000000000000000 ffffffff811ad232
Call Trace:
[<ffffffff8123ad65>] ? __pm_runtime_set_status+0x162/0x186
[<ffffffff811ad232>] ? local_pci_probe+0x49/0x92
[<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
[<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
[<ffffffff8105afd0>] ? do_work_for_cpu+0xb/0x1b
[<ffffffff8105fd3f>] ? kthread+0x7a/0x82
[<ffffffff8100a824>] ? kernel_thread_helper+0x4/0x10
[<ffffffff8105fcc5>] ? kthread+0x0/0x82
[<ffffffff8100a820>] ? kernel_thread_helper+0x0/0x10
Code: f4 01 00 00 ef 31 f6 48 89 df e8 29 dd ff ff 85 c0 0f 88 2b 03 00 00 48 89 ef e8 b4 39 c3 e0 8b 7b 40 e8 fc 9d b1 e0 48 8b 43 38 <66> 8b 10 66 89 14 24 8b 43 14 83 e8 03 83 f8 01 77 32 31 d2 be
RIP [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
RSP <ffff88013153fe50>
CR2: ffffc90011c08000
---[ end trace 8d1f3ebc136437fd ]---
Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.
$ dmesg | grep -i crs # with the quirk
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
The match has to be against the DMI board entries though since the vendor entries are not populated.
DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304 10/30/2007
This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.
Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.
15:13 < ruik> but coreboot does not need that
15:13 < ruik> because i have there only one root bus
15:13 < ruik> the audio is behind a bridge
$ sudo dmidecode
BIOS Information
Vendor: American Megatrends Inc.
Version: 0304
Release Date: 10/30/2007
[1] http://www.coreboot.org/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=30552
Cc: stable@kernel.org (2.6.34)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>