The helper intel_dsb_wait_vblank_delay() is used in DSB to wait for the
delayed vblank after the send push operation. Rename it to
intel_dsb_wait_for_delayed_vblank() to align with the semantics.
v2: Rename to intel_dsb_wait_vblank_delay instead of the proposed SCL
semantics, as this will be ot only about SCL lines with different timing
generator and different refresh rate modes. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-6-ankit.k.nautiyal@intel.com
For now guardband is equal to the vblank length so ideally it should be
computed as difference between the vmin vtotal and vactive. However
since we are having few lines as SCL, we need to account for this while
computing the guardband.
Since the vblank start is moved by SCL lines from the vactive, the delta
between the vmin vtotal and new vblank start was used to account for this.
Now that SCL is explicitly tracked using the `set_context_latency` member,
use it directly in the guardband calculation.
In the future, when the guardband is shortened or optimized, we may need
to factor in both the change in the vblank start and SCL lines. For now,
explicitly accounting for SCL is sufficient.
v2: Fix typo: replace adjusted_mode->vdisplay with
adjusted_mode->crtc_vdisplay. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-5-ankit.k.nautiyal@intel.com
The helper intel_vrr_real_vblank_delay() was added to account for the
SCL lines for TGL where we do not have the TRANS_SET_CONTEXT_LATENCY.
Now, since we already are tracking the SCL with new member
`set_context_latency` use it directly instead of the helper.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-4-ankit.k.nautiyal@intel.com
'Set context latency' (SCL, Window W2) is defined as the number of lines
before the double buffering point, which are required to complete
programming of the registers, typically when DSB is used to program the
display registers.
Since we are not using this window for programming the registers, this
is mostly set to 0, unless there is a requirement for few cases related
to PSR/PR where the 'set context latency' should be at least 1.
Currently we are using the 'set context latency' (if required) implicitly
by moving the vblank start by the required amount and then measuring the
delay i.e. the difference between undelayed vblank start and delayed vblank
start.
Since our guardband matches the vblank length, this was not a problem as
the difference between the undelayed vblank and delayed vblank was at
the most equal to the 'set context latency' lines.
However, if we want to optimize the guardband, the difference between the
undelayed and the delayed vblank will be large and we cannot use this
difference as the 'set context latency' lines.
To make way for this optimization of guardband, formally introduce the
'set context latency' or SCL and track it as a new member
`set_context_latency` of the structure intel_crtc_state.
Eventually, all references of vblank delay where we mean to use set
context latency will be replaced by this new `set_context_latency`
member.
Note: for TGL the TRANS_SET_CONTEXT_LATENCY doesn't exist to account for
the SCL. However, the VBLANK_START-VACTIVE difference plays an identical
role here ie. it can be used to create the SCL window ahead of the
undelayed vblank.
While readback since there is no specific register to read out the SCL, use
the difference between vblank start and vactive to populate the new member
for TGL.
v2:
- Use u16 for set_context_latency. (Ville)
- s/vblank_delay/set_context_latency. (Ville)
- Meld the changes for TGL with this change. (Ville)
v3:
- Update comment to clarify the TGL case. (Ville)
- Fix typo in commit message.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-3-ankit.k.nautiyal@intel.com
Rename intel_psr_min_vblank_delay to intel_psr_min_set_context_latency
to reflect that it provides the minimum value for 'Set context
latency'(SCL or Window W2) for PSR/Panel Replay to work correctly across
different platforms.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-2-ankit.k.nautiyal@intel.com
Designware databook r5.20a, sec 3.10.10.3 documents the 'CFG Shift Feature'
of the internal Address Translation Unit (iATU). When this feature is
enabled, it shifts/maps the BDF contained in the bits [27:12] of the target
address in MEM TLP to become BDF of the CFG TLP. This essentially
implements the Enhanced Configuration Address Mapping (ECAM) mechanism as
defined in PCIe r6.0, sec 7.2.2.
Currently, the driver is not making use of this CFG shift feature, thereby
creating the iATU outbound map for each config access to the devices,
causing latency and wasting CPU cycles.
So to avoid this, configure the controller to enable CFG shift feature by
enabling the 'CFG Shift' bit of the 'iATU Control 2 Register'.
As a result of enabling CFG shift (ECAM), there is no longer a need to map
the DBI register space separately as the DBI region falls under the
'config' space used for ECAM (as DBI is used to access the Root Port).
For enabling ECAM using CFG shift, the platform has to satisfy following
requirements:
1. Size of the 'config' memory space to be used as ECAM memory should be
able to accommodate the number of buses defined in the 'bus-range'
property of the host bridge DT node.
2. The 'config' memory space should be 256 MiB aligned. This requirement
comes from PCIe r6.0, sec 7.2.2, which says the base address of ECAM
memory should be aligned to a 2^(n+20) byte address boundary. For the
DWC cores, n is 8, so this results in 2^28 byte alignment requirement.
It should be noted that some DWC vendor glue drivers like pcie-al may use
their own ECAM mechanism. For those controllers, set
'dw_pcie_rp::native_ecam' flag and skip enabling the CFG Shift feature in
the DWC core.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: code split, reworded subject/description, comment, native_ecam flag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-4-e84390ba75fa@kernel.org
To support the DWC ECAM mechanism, prepare the driver by performing below
configurations:
1. Since the ELBI region will be covered by the ECAM 'config' space,
override the 'elbi_base' with the address derived from 'dbi_base' and
the offset from PARF_SLV_DBI_ELBI register.
2. Block the transactions from the host bridge to devices other than Root
Port on the root bus to return all F's. This is required when the 'CFG
Shift Feature' of iATU is enabled.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: code split, reworded subject/description and comments]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-3-e84390ba75fa@kernel.org
In order to enable PCIe ECAM mechanism in DWC driver as per the 'CFG Shift
Feature' documented in Designware databook r5.20a, sec 3.10.10.3, prepare
the driver to handle the one time iATU setup and creating ECAM window.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: splitted the preparatory code into a separate commit for bisectability]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-2-e84390ba75fa@kernel.org
External Local Bus Interface (ELBI) is an optional register space for all
DWC IPs containing the vendor specific registers. There is no need for the
vendor glue drivers to fetch and map the ELBI region separately.
Hence, optionally fetch and map the resource from DT in the DWC core. This
also warrants dropping the corresponding code from glue drivers. Hence,
drop the ELBI resource fetch and map logic from glue drivers and convert
them to use 'dw_pci::elbi_base'.
Note that the pcie-qcom-ep driver used devm_pci_remap_cfg_resource() to map
the ELBI resource previously. But it was a mistake since
devm_pci_remap_cfg_resource() should only be used for mapping the PCIe
config space region as it maps the region as Non-Posted. As ELBI is used to
hold vendor specific registers, there is no need to map the region as
Non-Posted. With this conversion, the region will get mapped as normal MMIO
memory.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: removed elbi override, converted glue drivers and reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-1-e84390ba75fa@kernel.org
When using bpf_program__attach_kprobe_multi_opts on ARM64 to hook a BPF program
that contains the bpf_get_stackid function, the BPF program fails
to obtain the stack trace and returns -EFAULT.
This is because ftrace_partial_regs omits the configuration of the pstate register,
leaving pstate at the default value of 0. When get_perf_callchain executes,
it uses user_mode(regs) to determine whether it is in kernel mode.
This leads to a misjudgment that the code is in user mode,
so perf_callchain_kernel is not executed and the function returns directly.
As a result, trace->nr becomes 0, and finally -EFAULT is returned.
Therefore, the assignment of the pstate register is added here.
Fixes: b9b55c8912 ("tracing: Add ftrace_partial_regs() for converting ftrace_regs to pt_regs")
Closes: https://lore.kernel.org/bpf/20250919071902.554223-1-yangfeng59949@163.com/
Signed-off-by: Feng Yang <yangfeng@kylinos.cn>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
The kprobe page is allocated by execmem allocator with ROX permission.
It needs to call set_memory_rox() to set proper permission for the
direct map too. It was missed.
Fixes: 10d5e97c1b ("arm64: use PAGE_KERNEL_ROX directly in alloc_insn_page")
Cc: <stable@vger.kernel.org>
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The rust USB bindings as submitted are a good start, but they don't
really seem to be correct in a number of minor places, so just disable
them from the build entirely at this point in time. When they are ready
to be re-enabled, this commit can be reverted.
Acked-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously tt_core is defined as config1:0-7 which may not cover all
the CPUs sharing L3C on platforms with more than 8 CPUs in a L3C. In
order to support such platforms extend tt_core to 16 bits, since no
spare space in config1, tt_core was moved to config2:0-15.
Though linux expects the users to retrieve the control encoding from
sysfs first for each option, it's possible if user doesn't follow
this and hardcoded tt_core in config1. So add an option
tt_core_deprecated for config1:0-7 for backward compatibility.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Will Deacon <will@kernel.org>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
system_wq is a per-CPU worqueue (replaced by system_percpu_wq), but the
current code does not benefit from it. Because of that, system_wq has been
replaced by system_dfl_wq, the new unbound workqueue.
The old wq will be kept for a few release cylces.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Mete Durlu <meted@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
system_wq is a per-CPU worqueue, yet nothing in its name tells about that
CPU affinity constraint, which is very often not required by users. Make
it clear by renaming system_wq to system_percpu_wq.
queue_work() / queue_delayed_work() mod_delayed_work() will now use the
new per-cpu wq.
The old wq will be kept for a few release cylces.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This patch adds a new WQ_PERCPU flag to explicitly request the use of
the per-CPU behavior. Both flags coexist for one release cycle to allow
callers to transition their calls.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
All existing users have been updated accordingly.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Convert the ams,as3645a.txt to DT Schema format.
Signed-off-by: Harrison Carter <hcarter@thegoodpenguin.co.uk>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Commit 5c83b07df9 ("tpm: Add a driver for Loongson TPM device") adds a
driver at drivers/char/tpm/tpm_loongson.c, and commit 74fddd5fba
("MAINTAINERS: Add entry for Loongson Security Engine drivers") adds a new
section LOONGSON SECURITY ENGINE DRIVERS intending to refer to that driver.
It however adds the entry drivers/char/tpm_loongson.c; note that it misses
the tpm subdirectory.
Adjust the entry to refer to the intended file.
Fixes: 74fddd5fba ("MAINTAINERS: Add entry for Loongson Security Engine drivers")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Commit 5c83b07df9 ("tpm: Add a driver for Loongson TPM device") has a
semantic conflict with commit 07d8004d6f ("tpm: add bufsiz parameter
in the .send callback"), as the former change was developed against a
tree without the latter change. This results in a build error:
drivers/char/tpm/tpm_loongson.c:48:17: error: initialization of 'int (*)(struct tpm_chip *, u8 *, size_t, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int, long unsigned int)'} from incompatible pointer type 'int (*)(struct tpm_chip *, u8 *, size_t)' {aka 'int (*)(struct tpm_chip *, unsigned char *, long unsigned int)'} [-Wincompatible-pointer-types]
48 | .send = tpm_loongson_send,
| ^~~~~~~~~~~~~~~~~
drivers/char/tpm/tpm_loongson.c:48:17: note: (near initialization for 'tpm_loongson_ops.send')
drivers/char/tpm/tpm_loongson.c:31:12: note: 'tpm_loongson_send' declared here
31 | static int tpm_loongson_send(struct tpm_chip *chip, u8 *buf, size_t count)
| ^~~~~~~~~~~~~~~~~
Add the expected bufsiz parameter to tpm_loongson_send() to resolve the
error.
Fixes: 5c83b07df9 ("tpm: Add a driver for Loongson TPM device")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
CONFIG_EFI_DEBUG embeds absolute file paths into object files, which
makes the resulting vmlinux specific to the build environment.
Add a note about this in reproducible-builds.rst
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nicolas Schier <nsc@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20250924-kbuild-doc-config-debug-efi-in-reproducible-builds-v2-1-d2d6b9dcdb7d@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Delete Björn Töpel and Jonathan Lemon as maintainer and reviewer,
respectively, as they have not been contributing towards AF_XDP for
several years. I have spoken to Björn and he is ok with his removal.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Acked-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/bpf/20250915120148.2922-1-magnus.karlsson@gmail.com
Add IPIP test-cases to the GRO selftest.
This selftest already contains IP ID test-cases. They are now
also tested for encapsulated packets.
This commit also fixes ipip packet generation in the test.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250923085908.4687-6-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, packets with fixed IDs will be merged only if their
don't-fragment bit is set. This restriction is unnecessary since
packets without the don't-fragment bit will be forwarded as-is even
if they were merged together. The merged packets will be segmented
into their original forms before being forwarded, either by GSO or
by TSO. The IDs will also remain identical unless NETIF_F_TSO_MANGLEID
is set, in which case the IDs can become incrementing, which is also fine.
Clean up the code by removing the unnecessary don't-fragment checks.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250923085908.4687-5-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, NETIF_F_TSO_MANGLEID indicates that the inner-most ID can
be mangled. Outer IDs can always be mangled.
Make GSO preserve outer IDs by default, with NETIF_F_TSO_MANGLEID allowing
both inner and outer IDs to be mangled.
This commit also modifies a few drivers that use SKB_GSO_FIXEDID directly.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com> # for sfc
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250923085908.4687-4-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Only merge encapsulated packets if their outer IDs are either
incrementing or fixed, just like for inner IDs and IDs of non-encapsulated
packets.
Add another ip_fixedid bit for a total of two bits: one for outer IDs (and
for unencapsulated packets) and one for inner IDs.
This commit preserves the current behavior of GSO where only the IDs of the
inner-most headers are restored correctly.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250923085908.4687-3-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove is_ipv6 from napi_gro_cb and use sk->sk_family instead.
This frees up space for another ip_fixedid bit that will be added
in the next commit.
udp_sock_create always creates either a AF_INET or a AF_INET6 socket,
so using sk->sk_family is reliable. In IPv6-FOU, cfg->ipv6_v6only is
always enabled.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250923085908.4687-2-richardbgobert@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add support to read module EEPROM for fbnic. Towards this, add required
support to issue a new command to the firmware and to receive the response
to the corresponding command.
Create a local copy of the data in the completion struct before writing to
ethtool_module_eeprom to avoid writing to data in case it is freed. Given
that EEPROM pages are small, the overhead of additional copy is
negligible.
Do not block API with explicit checks since API has appropriate checks in
place for length, offset, and page.
Explicitly check bank, page, offset, and length in
fbnic_fw_parse_qsfp_read_resp() to match EEPROM read responses to the
correct request. This is important because if the driver times out waiting
for an EEPROM read response, a subsequent read request with different
values is susceptible to receiving an erroneous response (i.e., the
response to the previous request).
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20250922231855.3717483-1-mohsin.bashr@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When WMAB is called to set the fan mode, the new mode is read from either
bits 0-1 or bits 4-5 (depending on the value of some other EC register).
Thus when WMAB is called with bits 4-5 zeroed and called again with
bits 0-1 zeroed, the second call undoes the effect of the first call.
This causes writes to /sys/devices/platform/lg-laptop/fan_mode to have
no effect (and causes reads to always report a status of zero).
Fix this by calling WMAB once, with the mode set in bits 0,1 and 4,5.
When the fan mode is returned from WMAB it always has this form, so
there is no need to preserve the other bits. As a bonus, the driver
now supports the "Performance" fan mode seen in the LG-provided Windows
control app, which provides less aggressive CPU throttling but louder
fan noise and shorter battery life.
Also, correct the documentation to reflect that 0 corresponds to the
default mode (what the Windows app calls "Optimal") and 1 corresponds
to the silent mode.
Fixes: dbf0c5a6b1 ("platform/x86: Add LG Gram laptop special features driver")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204913#c4
Signed-off-by: Daniel Lee <dany97@live.ca>
Link: https://patch.msgid.link/MN2PR06MB55989CB10E91C8DA00EE868DDC1CA@MN2PR06MB5598.namprd06.prod.outlook.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
This code calls kfree_rcu(new_node, rcu) and then dereferences "new_node"
and then dereferences it on the next line. Two lines later, we take
a mutex so I don't think this is an RCU safe region. Re-order it to do
the dereferences before queuing up the free.
Fixes: 68fbff68db ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/aNKCL1jKwK8GRJHh@stanley.mountain
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit de85488138 ("drm/panthor: Add the scheduler logical block")
handled destruction of a group's queues' drm scheduler entities early
into the group destruction procedure.
However, that races with the group submit ioctl, because by the time
entities are destroyed (through the group destroy ioctl), the submission
procedure might've already obtained a group handle, and therefore the
ability to push jobs into entities. This is met with a DRM error message
within the drm scheduler core as a situation that should never occur.
Fix by deferring drm scheduler entity destruction to queue release time.
Fixes: de85488138 ("drm/panthor: Add the scheduler logical block")
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250919164436.531930-1-adrian.larumbe@collabora.com
Add i915_gem_fence_wait_priority_display() helper to wait with
I915_PRIORITY_DISPLAY. This drops the intel_plane.c dependency on
i915_scheduler_types.h, and allows us to remove the compat header from
xe.
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250924085129.146173-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Vladimir Oltean says:
====================
lantiq_gswip fixes
This is a small set of fixes which I believe should be backported for
the lantiq_gswip driver. Daniel Golle asked me to submit them here:
https://lore.kernel.org/netdev/aLiDfrXUbw1O5Vdi@pidgin.makrotopia.org/
As mentioned there, a merge conflict with net-next is expected, due to
the movement of the driver to the 'drivers/net/dsa/lantiq' folder there.
Good luck :-/
Patch 2/2 fixes an old regression and is the minimal fix for that, as
discussed here:
https://lore.kernel.org/netdev/aJfNMLNoi1VOsPrN@pidgin.makrotopia.org/
Patch 1/2 was identified by me through static analysis, and I consider
it to be a serious deficiency. It needs a test tag.
====================
Link: https://patch.msgid.link/20250918072142.894692-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The blamed commit and others in that patch set started the trend
of reusing existing DSA driver API for a new purpose: calling
ds->ops->port_fdb_add() on the CPU port.
The lantiq_gswip driver was not prepared to handle that, as can be seen
from the many errors that Daniel presents in the logs:
[ 174.050000] gswip 1e108000.switch: port 2 failed to add fa:aa:72:f4:8b:1e vid 1 to fdb: -22
[ 174.060000] gswip 1e108000.switch lan2: entered promiscuous mode
[ 174.070000] gswip 1e108000.switch: port 2 failed to add 00:01:02:03:04:02 vid 0 to fdb: -22
[ 174.090000] gswip 1e108000.switch: port 2 failed to add 00:01:02:03:04:02 vid 1 to fdb: -22
[ 174.090000] gswip 1e108000.switch: port 2 failed to delete fa:aa:72:f4:8b:1e vid 1 from fdb: -2
The errors are because gswip_port_fdb() wants to get a handle to the
bridge that originated these FDB events, to associate it with a FID.
Absolutely honourable purpose, however this only works for user ports.
To get the bridge that generated an FDB entry for the CPU port, one
would need to look at the db.bridge.dev argument. But this was
introduced in commit c26933639b ("net: dsa: request drivers to perform
FDB isolation"), first appeared in v5.18, and when the blamed commit was
introduced in v5.14, no such API existed.
So the core DSA feature was introduced way too soon for lantiq_gswip.
Not acting on these host FDB entries and suppressing any errors has no
other negative effect, and practically returns us to not supporting the
host filtering feature at all - peacefully, this time.
Fixes: 10fae4ac89 ("net: dsa: include bridge addresses which are local in the host fdb list")
Reported-by: Daniel Golle <daniel@makrotopia.org>
Closes: https://lore.kernel.org/netdev/aJfNMLNoi1VOsPrN@pidgin.makrotopia.org/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250918072142.894692-3-vladimir.oltean@nxp.com
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A port added to a "single port bridge" operates as standalone, and this
is mutually exclusive to being part of a Linux bridge. In fact,
gswip_port_bridge_join() calls gswip_add_single_port_br() with
add=false, i.e. removes the port from the "single port bridge" to enable
autonomous forwarding.
The blamed commit seems to have incorrectly thought that ds->ops->port_enable()
is called one time per port, during the setup phase of the switch.
However, it is actually called during the ndo_open() implementation of
DSA user ports, which is to say that this sequence of events:
1. ip link set swp0 down
2. ip link add br0 type bridge
3. ip link set swp0 master br0
4. ip link set swp0 up
would cause swp0 to join back the "single port bridge" which step 3 had
just removed it from.
The correct DSA hook for one-time actions per port at switch init time
is ds->ops->port_setup(). This is what seems to match the coder's
intention; also see the comment at the beginning of the file:
* At the initialization the driver allocates one bridge table entry for
~~~~~~~~~~~~~~~~~~~~~
* each switch port which is used when the port is used without an
* explicit bridge.
Fixes: 8206e0ce96 ("net: dsa: lantiq: Add VLAN unaware bridge offloading")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250918072142.894692-2-vladimir.oltean@nxp.com
Tested-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are some typos in the comments of migrate in
include/linux/preempt.h:
elegible -> eligible
it's -> its
migirate_disable -> migrate_disable
abritrary -> arbitrary
Just fix them.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
For now, migrate_enable and migrate_disable are global, which makes them
become hotspots in some case. Take BPF for example, the function calling
to migrate_enable and migrate_disable in BPF trampoline can introduce
significant overhead, and following is the 'perf top' of FENTRY's
benchmark (./tools/testing/selftests/bpf/bench trig-fentry):
54.63% bpf_prog_2dcccf652aac1793_bench_trigger_fentry [k]
bpf_prog_2dcccf652aac1793_bench_trigger_fentry
10.43% [kernel] [k] migrate_enable
10.07% bpf_trampoline_6442517037 [k] bpf_trampoline_6442517037
8.06% [kernel] [k] __bpf_prog_exit_recur
4.11% libc.so.6 [.] syscall
2.15% [kernel] [k] entry_SYSCALL_64
1.48% [kernel] [k] memchr_inv
1.32% [kernel] [k] fput
1.16% [kernel] [k] _copy_to_user
0.73% [kernel] [k] bpf_prog_test_run_raw_tp
So in this commit, we make migrate_enable/migrate_disable inline to obtain
better performance. The struct rq is defined internally in
kernel/sched/sched.h, and the field "nr_pinned" is accessed in
migrate_enable/migrate_disable, which makes it hard to make them inline.
Alexei Starovoitov suggests to generate the offset of "nr_pinned" in [1],
so we can define the migrate_enable/migrate_disable in
include/linux/sched.h and access "this_rq()->nr_pinned" with
"(void *)this_rq() + RQ_nr_pinned".
The offset of "nr_pinned" is generated in include/generated/rq-offsets.h
by kernel/sched/rq-offsets.c.
Generally speaking, we move the definition of migrate_enable and
migrate_disable to include/linux/sched.h from kernel/sched/core.c. The
calling to __set_cpus_allowed_ptr() is leaved in ___migrate_enable().
The "struct rq" is not available in include/linux/sched.h, so we can't
access the "runqueues" with this_cpu_ptr(), as the compilation will fail
in this_cpu_ptr() -> raw_cpu_ptr() -> __verify_pcpu_ptr():
typeof((ptr) + 0)
So we introduce the this_rq_raw() and access the runqueues with
arch_raw_cpu_ptr/PERCPU_PTR directly.
The variable "runqueues" is not visible in the kernel modules, and export
it is not a good idea. As Peter Zijlstra advised in [2], we define and
export migrate_enable/migrate_disable in kernel/sched/core.c too, and use
them for the modules.
Before this patch, the performance of BPF FENTRY is:
fentry : 113.030 ± 0.149M/s
fentry : 112.501 ± 0.187M/s
fentry : 112.828 ± 0.267M/s
fentry : 115.287 ± 0.241M/s
After this patch, the performance of BPF FENTRY increases to:
fentry : 143.644 ± 0.670M/s
fentry : 149.764 ± 0.362M/s
fentry : 149.642 ± 0.156M/s
fentry : 145.263 ± 0.221M/s
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/bpf/CAADnVQ+5sEDKHdsJY5ZsfGDO_1SEhhQWHrt2SMBG5SYyQ+jt7w@mail.gmail.com/ [1]
Link: https://lore.kernel.org/all/20250819123214.GH4067720@noisy.programming.kicks-ass.net/ [2]
In the next commit, we will move the definition of migrate_enable() and
migrate_disable() to linux/sched.h. However,
migrate_enable/migrate_disable will be used in commit
1b93c03fb3 ("rcu: add rcu_read_lock_dont_migrate()") in bpf-next tree.
In order to fix potential compiling error, replace linux/preempt.h with
linux/sched.h in include/linux/rcupdate.h.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
The include/generated/asm-offsets.h is generated in Kbuild during
compiling from arch/SRCARCH/kernel/asm-offsets.c. When we want to
generate another similar offset header file, circular dependency can
happen.
For example, we want to generate a offset file include/generated/test.h,
which is included in include/sched/sched.h. If we generate asm-offsets.h
first, it will fail, as include/sched/sched.h is included in asm-offsets.c
and include/generated/test.h doesn't exist; If we generate test.h first,
it can't success neither, as include/generated/asm-offsets.h is included
by it.
In x86_64, the macro COMPILE_OFFSETS is used to avoid such circular
dependency. We can generate asm-offsets.h first, and if the
COMPILE_OFFSETS is defined, we don't include the "generated/test.h".
And we define the macro COMPILE_OFFSETS for all the asm-offsets.c for this
purpose.
Signed-off-by: Menglong Dong <dongml2@chinatelecom.cn>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
John reported undesirable behaviour with the dl_server since commit:
cccb45d7c4 ("sched/deadline: Less agressive dl_server handling").
When starving fair tasks on purpose (starting spinning FIFO tasks),
his fair workload, which often goes (briefly) idle, would delay fair
invocations for a second, running one invocation per second was both
unexpected and terribly slow.
The reason this happens is that when dl_se->server_pick_task() returns
NULL, indicating no runnable tasks, it would yield, pushing any later
jobs out a whole period (1 second).
Instead simply stop the server. This should restore behaviour in that
a later wakeup (which restarts the server) will be able to continue
running (subject to the CBS wakeup rules).
Notably, this does not re-introduce the behaviour cccb45d7c4 set
out to solve, any start/stop cycle is naturally throttled by the timer
period (no active cancel).
Fixes: cccb45d7c4 ("sched/deadline: Less agressive dl_server handling")
Reported-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: John Stultz <jstultz@google.com>
John found it was easy to hit lockup warnings when running locktorture
on a 2 CPU VM, which he bisected down to: commit cccb45d7c4
("sched/deadline: Less agressive dl_server handling").
While debugging it seems there is a chance where we end up with the
dl_server dequeued, with dl_se->dl_server_active. This causes
dl_server_start() to return without enqueueing the dl_server, thus it
fails to run when RT tasks starve the cpu.
When this happens, dl_server_timer() catches the
'!dl_se->server_has_tasks(dl_se)' case, which then calls
replenish_dl_entity() and dl_server_stopped() and finally return
HRTIMER_NO_RESTART.
This ends in no new timer and also no enqueue, leaving the dl_server
'dead', allowing starvation.
What should have happened is for the bandwidth timer to start the
zero-laxity timer, which in turn would enqueue the dl_server and cause
dl_se->server_pick_task() to be called -- which will stop the
dl_server if no fair tasks are observed for a whole period.
IOW, it is totally irrelevant if there are fair tasks at the moment of
bandwidth refresh.
This removes all dl_se->server_has_tasks() users, so remove the whole
thing.
Fixes: cccb45d7c4 ("sched/deadline: Less agressive dl_server handling")
Reported-by: John Stultz <jstultz@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: John Stultz <jstultz@google.com>
Christian Brauner <brauner@kernel.org> says:
This contains three minor tweaks for namespace handling:
* Make struct ns_tree private. There's no need for anything to access
that directly.
* Drop a debug assert that would trigger in conditions that are benign.
* Move the type of the namespace out of struct proc_ns_operations and
into struct ns_common. This eliminates a pointer dereference and also
allows assertions to work when the namespace type is disabled and the
operations field set to NULL.
* patches from https://lore.kernel.org/20250924-work-namespaces-fixes-v1-0-8fb682c8678e@kernel.org:
ns: drop assert
ns: move ns type into struct ns_common
nstree: make struct ns_tree private
Signed-off-by: Christian Brauner <brauner@kernel.org>
Otherwise we warn when e.g., no namespaces are configured but the
initial namespace for is still around.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
It's misplaced in struct proc_ns_operations and ns->ops might be NULL if
the namespace is compiled out but we still want to know the type of the
namespace for the initial namespace struct.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add support for RENAME_NOREPLACE and RENAME_EXCHANGE, if the server
supports them.
The default is translated to YFS.Rename_Replace, falling back to
YFS.Rename; RENAME_NOREPLACE is translated to YFS.Rename_NoReplace and
RENAME_EXCHANGE to YFS.Rename_Exchange, both of which fall back to
reporting EINVAL.
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/740476.1758718189@warthog.procyon.org.uk
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Dan Carpenter <dan.carpenter@linaro.org>
cc: linux-afs@lists.infradead.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
afs_put_server() accessed server->debug_id before the NULL check, which
could lead to a null pointer dereference. Move the debug_id assignment,
ensuring we never dereference a NULL server pointer.
Fixes: 2757a4dc18 ("afs: Fix access after dec in put functions")
Cc: stable@vger.kernel.org
Signed-off-by: Zhen Ni <zhen.ni@easystack.cn>
Acked-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add minimal device tree for HiFive Premier P550 Development board
Currently the data populated in this DT file is for UART.
Signed-off-by: Min Lin <linmin@eswincomputing.com>
Co-developed-by: Pinkesh Vaghela <pinkesh.vaghela@einfochips.com>
Signed-off-by: Pinkesh Vaghela <pinkesh.vaghela@einfochips.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20250825132427.1618089-7-pinkesh.vaghela@einfochips.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add initial support for EIC7700 SoC that uses a SiFive Quad-Core
P550 CPU cluster.
This file is expected to grow as more device drivers are added to the
kernel.
Signed-off-by: Min Lin <linmin@eswincomputing.com>
Co-developed-by: Pritesh Patel <pritesh.patel@einfochips.com>
Signed-off-by: Pritesh Patel <pritesh.patel@einfochips.com>
Co-developed-by: Darshan Prajapati <darshan.prajapati@einfochips.com>
Signed-off-by: Darshan Prajapati <darshan.prajapati@einfochips.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Pinkesh Vaghela <pinkesh.vaghela@einfochips.com>
Link: https://lore.kernel.org/r/20250825132427.1618089-6-pinkesh.vaghela@einfochips.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
