__io_uring_show_fdinfo() iterates over pending SQEs and, for 128-byte
SQEs on an IORING_SETUP_SQE_MIXED ring, needs to detect when the second
half of the SQE would be past the end of the sq_sqes array. The current
check tests (++sq_head & sq_mask) == 0, but sq_head is only incremented
when a 128-byte SQE is encountered, not on every iteration. The actual
array index is sq_idx = (i + sq_head) & sq_mask, which can be sq_mask
(the last slot) while the wrap check passes.
Fix by checking sq_idx directly. Keep the sq_head increment so the loop
still skips the second half of the 128-byte SQE on the next iteration.
Fixes: 1cba30bf9f ("io_uring: add support for IORING_SETUP_SQE_MIXED")
Signed-off-by: Nicholas Carlini <nicholas@carlini.com>
Link: https://patch.msgid.link/20260327021823.3138396-1-nicholas@carlini.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Enable the two PCIe controller along with and their associated PHY. They
are routed to the M.2 M-key connector and to the PCIe x8 slot.
Add an always-on regulator sourcing 3.3V from the DC-IN input, to power
the PCIe ports.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-7-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
Enable the DWC3 USB 3.0 controller (USB#2 port in the K1 datasheet) and
its associated combo_phy (USB 3 PHY) and usbphy2 (USB 2 PHY) on the
Milk-V Jupiter board.
The board uses a VLI VL817 hub, providing four ports. Two are routed to
the 3.0 type-A connectors, and two to the F_USB3 front USB header. The
hub requires two separate 5V power supplies: one for the hub itself and
one for the USB connectors. Add an always-on regulator sourcing 5V from
the DC-IN input, along with two GPIO-controlled fixed regulators to
manage the hub and connectors power supplies.
Note that the board also provides four USB 2.0 ports (two via type-A
connectors and two via the F_USB2 front USB header), but these are
handled by a different controller (USB#1 port in the K1 datasheet).
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-6-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
Add the QSPI controller node for the Milk-V Jupiter board and describe
the attached SPI NOR flash (GD25Q64E).
The flash supports a frequency up to 133MHz (80 MHz for reads), and the
SoC supports a frequency up to 104 MHz. However tests have shown that
the flash is not reliably detected above 26.5 MHz, consistent with
frequency used in the vendor kernel. Therefore, use this frequency.
The m25p,fast-read properties is taken from the vendor kernel, and the
GD25Q64E datasheet confirms tha the fast read opcodes are supported.
Add a corresponding flash partition layout, matching the layout and the
names used in the vendor U-Boot.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-5-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
Add i2c aliases for i2c2 and i2c8 on Milk-V Jupiter. This is useful to
keep a stable number for the /dev entries after loading the i2c-dev
module.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-4-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
The Milk-V Jupiter board includes a 24c04 eeprom on the i2c2 bus. The
eeprom contains an ONIE TLV table, which on the board I tested only
provides a product-name entry. Expose it via an onie,tlv-layout nvmem
layout.
The eeprom is marked as read-only since its contents are not supposed to
be modified.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-3-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
The Milk-V Jupiter board provides support for two LEDs through the front
panel header. The "Power LED" indicates the system is running, and the
"HDD LED" shows disk activity. Configure the corresponding LED triggers
accordingly.
Caveats:
- The LEDs are driven through a 4.7k series resistor, making them
quite faint.
- The disk activity trigger requires a storage controller on the M.2 or
PCIe interface. That said, it matches the purpose and the vendor
kernel.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
Link: https://lore.kernel.org/r/20260326183745.1370642-2-aurelien@aurel32.net
Signed-off-by: Yixun Lan <dlan@kernel.org>
This node describes a memory address range containing several sub-regions
with control registers for various IP in the MAIN domain of this SoC. It
was described as a "ti,j721e-system-controller" but this is a J721S2 SoC
with is not compatible with the system controller region found in J721e.
No project consuming this DT has been found that makes use of the syscon
compatible for this region, to prevent any from using this node like a
generic syscon region in the future, make this a normal simple-bus as
it should have been from the start.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20260303205224.108217-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This node describes a memory address range containing several sub-regions
with control registers for various IP in the MAIN domain of this SoC. It
was described as a "ti,j721e-system-controller" but this is a J7200 SoC
with is not compatible with the system controller region found in J721e.
No project consuming this DT has been found that makes use of the syscon
compatible for this region, to prevent any from using this node like a
generic syscon region in the future, make this a normal simple-bus as
it should have been from the start.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20260303205224.108217-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62 LP SK board does not have external pullups on MMC0 DAT1-DAT7
pins [0]. Enable internal pullups on DAT1-DAT7 considering:
- without a host-side pullup, these lines rely solely on the eMMC
device's internal pullup (R_int, 10-150K per JEDEC), which may
exceed the recommended 50K max for 1.8V VCCQ
- JEDEC JESD84-B51 Table 200 requires host-side pullups (R_DAT,
10K-100K) on all data lines to prevent bus floating
[0] https://www.ti.com/lit/zip/SPRR471
Fixes: a0b8da0415 ("arm64: dts: ti: k3-am62*: Move eMMC pinmux to top level board file")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260223233731.2690472-4-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62L EVM has external 47K pullups on MMC1 DAT1-DAT3 pins [0].
Disable internal pullups on DAT1-DAT3 so that each line has a
single pullup source:
- with both pullups enabled, the effective parallel resistance on
DAT1-3 (~24.2K) creates a ~2x mismatch vs DAT0 (47K external
only). Removing internal pullups results in DAT1-3 matching DAT0 at 47K
- 47K external alone is within the recommended range for 1.8V
signaling (10K min, 50K recommended max)
- both internal and external pullups enabled equals unnecessary power
consumption
[0] https://www.ti.com/lit/zip/SPRCAL6
Fixes: 00fb4c73b6 ("arm64: dts: ti: k3-am62l: add initial reference board file")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260223233731.2690472-3-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
AM62P SK has external 10K pullups on MMC1 DAT1-DAT3 pins [0].
Disable internal pullups on DAT1-DAT3 so that each line has a
single pullup source:
- with both pullups enabled, the effective parallel resistance on
DAT1-3 (~8.33K) drops below the 10K minimum pullup requirement
for data lines (per SD Physical Layer Specification)
- removing internal pullups makes DAT1-3 match DAT0 10K
external pullup so its consistent and within spec
- both internal and external pullups enabled equals unnecessary power
consumption
[0] https://www.ti.com/lit/zip/SPRR487
Fixes: c00504ea42 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260223233731.2690472-2-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The Main UART can resume from suspend to RAM states when PIN_WKUP_EN
is enabled. Add the necessary pins needed to wakeup the system. Add the
system idle states that the Main UART can wakeup the system from.
The UART driver uses the "default" pinctrl state when the system is
active. In the suspend hook, if the UART is wakeup enabled, the "wakeup"
pinctrl state is selected by the UART driver in order to allow wakeup.
Upon resume, the default pinctrl state is selected again.
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260212-b4-uart-daisy-chain-dts-v5-5-26c7f534e567@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The Main UART can resume from suspend to RAM states when PIN_WKUP_EN
is enabled. Add the necessary pins needed to wakeup the system. Add the
system idle states that the Main UART can wakeup the system from.
The UART driver uses the "default" pinctrl state when the system is
active. In the suspend hook, if the UART is wakeup enabled, the "wakeup"
pinctrl state is selected by the UART driver in order to allow wakeup.
Upon resume, the default pinctrl state is selected again.
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260212-b4-uart-daisy-chain-dts-v5-4-26c7f534e567@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The Main UART can resume from suspend to RAM states when PIN_WKUP_EN
is enabled. Add the necessary pins needed to wakeup the system. Add the
system idle states that the Main UART can wakeup the system from.
The UART driver uses the "default" pinctrl state when the system is
active. In the suspend hook, if the UART is wakeup enabled, the "wakeup"
pinctrl state is selected by the UART driver in order to allow wakeup.
Upon resume, the default pinctrl state is selected again.
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260212-b4-uart-daisy-chain-dts-v5-3-26c7f534e567@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The Main UART can resume from suspend to RAM states when PIN_WKUP_EN
is enabled. Add the necessary pins needed to wakeup the system. Add the
system idle states that the Main UART can wakeup the system from.
The UART driver uses the "default" pinctrl state when the system is
active. In the suspend hook, if the UART is wakeup enabled, the "wakeup"
pinctrl state is selected by the UART driver in order to allow wakeup.
Upon resume, the default pinctrl state is selected again.
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260212-b4-uart-daisy-chain-dts-v5-2-26c7f534e567@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The Main UART can resume from suspend to RAM states when PIN_WKUP_EN
is enabled. Add the necessary pins needed to wakeup the system. Add the
system idle states that the Main UART can wakeup the system from.
The UART driver uses the "default" pinctrl state when the system is
active. In the suspend hook, if the UART is wakeup enabled, the "wakeup"
pinctrl state is selected by the UART driver in order to allow wakeup.
Upon resume, the default pinctrl state is selected again.
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260212-b4-uart-daisy-chain-dts-v5-1-26c7f534e567@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
If the gmac0 is disabled, the precheck for a valid ingress device will
cause a NULL pointer deref and crash the system. This happens because
eth->netdev[0] will be NULL but the code will directly try to access
netdev_ops.
Instead of just checking for the first net_device, it must be checked if
any of the mtk_eth net_devices is matching the netdev_ops of the ingress
device.
Cc: stable@vger.kernel.org
Fixes: 73cfd947db ("net: ethernet: mtk_eth_soc: ppe: prevent ppe update for non-mtk devices")
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260324-wed-crash-gmac0-disabled-v1-1-3bc388aee565@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MANA passes rxq->alloc_size to napi_build_skb() for all RX buffers.
It is correct for fragment-backed RX buffers, where alloc_size matches
the actual backing allocation used for each packet buffer. However, in
the non-fragment RX path mana allocates a full page, or a higher-order
page, per RX buffer. In that case alloc_size only reflects the usable
packet area and not the actual backing memory.
This causes napi_build_skb() to underestimate the skb backing allocation
in the single-buffer RX path, so skb->truesize is derived from a value
smaller than the real RX buffer allocation.
Fix this by updating alloc_size in the non-fragment RX path to the
actual backing allocation size before it is passed to napi_build_skb().
Fixes: 730ff06d3f ("net: mana: Use page pool fragments for RX buffers instead of full pages to improve memory efficiency.")
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://patch.msgid.link/acLUhLpLum6qrD/N@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxime Chevallier says:
====================
net: dsa: microchip: Small cleanups for ksz9477 SGMII
While working with ksz9477, I've done some very minor cleanups around the
PCS code for the SGMII port. No changes intended.
====================
Link: https://patch.msgid.link/20260324180826.524327-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SGMII support has been added to ksz9477, we can drop the comment saying
that it'll be added later.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260324180826.524327-3-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz_dev_ops .pcs_create() is called under the assumption that the
switch has a PCS port :
if (ksz_has_sgmii_port(dev) && dev->dev_ops->pcs_create) {
ret = dev->dev_ops->pcs_create(dev);
[...]
}
The KSZ9477 implementation of .pcs_create() does the same check on
ksz_has_sgmii_port(), and protects the entire function with it.
Drop it, saving a level of indentation and increasing readability.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20260324180826.524327-2-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Address "grep: warning: stray \ before white space" warning from GNU
grep 3.12. This warns the misplaced backslashes before whitespaces
(e.g. \\' ' or '\ ') which leads to unspecified behavior [1].
We can just remove the backslashes before whitespaces as POSIX says:
Enclosing characters in single-quotes ('') shall preserve the literal
value of each character within the single-quotes.
and bourne-compatible shells behave so.
[1]: https://lists.gnu.org/r/bug-gnulib/2022-05/msg00057.html
Signed-off-by: Yohei Kojima <yk@y-koj.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/dd0bbd48cdf468da56ec34fd61cecd4d2111d7ba.1774372510.git.yk@y-koj.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, we incorrectly send messages that are within 4 bytes (a
struct mctp_hdr) smaller than the MTU through mctp_do_fragment_route().
This has no effect on the actual fragmentation, as we will still send as
one packet, but unnecessarily copies the original skb into a new
single-fragment skb.
Instead of having the MTU comparisons in both mctp_local_output() and
mctp_do_fragment_route(), feed all local messages through the latter,
and add the single-packet optimisation there.
This means we can coalesce the routing path of mctp_local_output, so our
out_release path is now solely for errors, so rename the label
accordingly.
Include a check in the route tests for the single-packet case too.
Reported-by: yuanzhaoming <yuanzm2@lenovo.com>
Closes: 269936db5e (r175836230)
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260324-dev-mtu-copy-v1-1-7af6bd7027d3@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Justin Iurman says:
====================
Add support for per-route seg6 tunsrc
This series adds support for the new per-route seg6 "tunsrc" parameter.
Selftests are extended to make sure it works as expected.
Example with the iproute2-next companion patch:
ip -6 r a 2001:db8:1::/64 encap seg6 mode encap tunsrc 2001:db8:ab::
segs 2001:db8:42::1,2001:db8:ffff::2 dev eth0
====================
Link: https://patch.msgid.link/20260324091434.359341-1-justin.iurman@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend srv6_hencap_red_l3vpn_test.sh to include checks for the new
"tunsrc" feature. If there is no support for tunsrc, it silently
falls back to the encap config without tunsrc.
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Justin Iurman <justin.iurman@6wind.com>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Link: https://patch.msgid.link/20260324091434.359341-3-justin.iurman@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add SEG6_IPTUNNEL_SRC in the uapi for users to configure a specific
tunnel source address. Make seg6_iptunnel handle the new attribute
correctly. It has priority over the configured per-netns tunnel
source address, if any.
Cc: David Ahern <dsahern@kernel.org>
Signed-off-by: Justin Iurman <justin.iurman@6wind.com>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Link: https://patch.msgid.link/20260324091434.359341-2-justin.iurman@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have
an inconsistent view of platform_labels vs platform_label in case of a
concurrent resize (resize_platform_label_table, under
platform_mutex). This can lead to OOB accesses.
This patch adds a seqcount, so that we get a consistent snapshot.
Note that mpls_label_ok is also susceptible to this, so the check
against RTA_DST in rtm_to_route_config, done outside platform_mutex,
is not sufficient. This value gets passed to mpls_label_ok once more
in both mpls_route_add and mpls_route_del, so there is no issue, but
that additional check must not be removed.
Reported-by: Yuan Tan <tanyuan98@outlook.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Fixes: 7720c01f3f ("mpls: Add a sysctl to control the size of the mpls label table")
Fixes: dde1b38e87 ("mpls: Convert mpls_dump_routes() to RCU.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/cd8fca15e3eb7e212b094064cd83652e20fd9d31.1774284088.git.sd@queasysnail.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tests in phylink_expects_phy() and phylink_fwnode_phy_connect() are
identical (by intention). Use phylink_expects_phy() to decide whether
to ignore a call to phylink_fwnode_phy_connect().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/E1w4zHg-0000000DmC4-2oyb@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxime Chevallier says:
====================
net: stmmac: dwmac-socfpga: Cleanup .fix_mac_speed
This small series does a bit of cleanup in the dwmad-socfpga glue
driver, especially around the .fix_mac_speed() operation.
It's mostly about re-using existing helpers from the glue driver, as
well as reorganizing the code to make the local private structures a
little bit smaller.
No functionnal changes are intended, this was tested on cyclone V.
====================
Link: https://patch.msgid.link/20260324092102.687082-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We keep a reference to our the struct device in the socfpga_dwmac priv
structure, but now it's only ever used to produce logs in the
.set_phy_mode() ops, that are specific to this driver.
When we call that ops, we always have a ref to the struct device around,
so let's pass it to .set_phy_mode(). We can now discard that reference
from struct socfpga_dwmac.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260324092102.687082-6-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We enable/disable the sgmii_adapter in the .fix_mac_speed() ops based on
the phy_mode used in the plat_data. We currently get it with :
socfpga_dwmac
->dev
->drv_data
->netdev
->priv
->stmmac_priv
->plat
->phy_interface
where we can get it with :
socfpga_dwmac
->plat_data
->phy_interface (done by socfpga_get_plat_phymode)
Use that helper here.
Note that we are also being passed a phy_interface_t from the
.fix_mac_speed() callback, provided by phylink.
We can handle that in the future when dynamic interface selection is
supported. We'd need to guarantee that we have a Lynx PCS to handle it.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260324092102.687082-5-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The internal helper socfpga_get_plat_phymode() returns an int where we
actually return a PHY_INTERFACE_MODE_xxx, use the correct type for this.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260324092102.687082-4-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the existing socfpga_sgmii_config() helper in
socfpga_dwmac_fix_mac_speed(), instead of re-coding the register access.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260324092102.687082-3-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is preparatory work to allow reusing the SGMII configuration helper
and the wrapper to get the interface in the fix_mac_speed() callback.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20260324092102.687082-2-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- cfg80211: new APIs for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware
- mt76:
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- iwlwifi: UNII-9 and continuing UHR work
-----BEGIN PGP SIGNATURE-----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=zap4
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
A fairly big set of changes all over, notably with:
- cfg80211: new APIs for NAN (Neighbor Aware Networking,
aka Wi-Fi Aware) so less work must be in firmware
- mt76:
- mt7996/mt7925 MLO fixes/improvements
- mt7996 NPU support (HW eth/wifi traffic offload)
- iwlwifi: UNII-9 and continuing UHR work
* tag 'wireless-next-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (230 commits)
wifi: mac80211: ignore reserved bits in reconfiguration status
wifi: cfg80211: allow protected action frame TX for NAN
wifi: ieee80211: Add some missing NAN definitions
wifi: nl80211: Add a notification to notify NAN channel evacuation
wifi: nl80211: add NL80211_CMD_NAN_ULW_UPDATE notification
wifi: nl80211: allow reporting spurious NAN Data frames
wifi: cfg80211: allow ToDS=0/FromDS=0 data frames on NAN data interfaces
wifi: nl80211: define an API for configuring the NAN peer's schedule
wifi: nl80211: add support for NAN stations
wifi: cfg80211: separately store HT, VHT and HE capabilities for NAN
wifi: cfg80211: add support for NAN data interface
wifi: cfg80211: make sure NAN chandefs are valid
wifi: cfg80211: Add an API to configure local NAN schedule
wifi: mac80211: cleanup error path of ieee80211_do_open
wifi: mac80211: extract channel logic from link logic
wifi: iwlwifi: mld: set RX_FLAG_RADIOTAP_TLV_AT_END generically
wifi: iwlwifi: reduce the number of prints upon firmware crash
wifi: iwlwifi: fix the description of SESSION_PROTECTION_CMD
wifi: iwlwifi: mld: introduce iwl_mld_vif_fw_id_valid
wifi: iwlwifi: mld: block EMLSR during TDLS connections
...
====================
Link: https://patch.msgid.link/20260326152021.305959-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Joey Lu says:
====================
Add support for Nuvoton MA35D1 GMAC
This patch series is submitted to add GMAC support for Nuvoton MA35D1
SoC platform. This work involves implementing a GMAC driver glue layer
based on Synopsys DWMAC driver framework to leverage MA35D1's dual GMAC
interface capabilities.
Overview:
1. Added a GMAC driver glue layer for MA35D1 SoC, providing support for
the platform's two GMAC interfaces.
2. Added device tree settings, with specific configurations for our
development boards:
a. SOM board: Configured for two RGMII interfaces.
b. IoT board: Configured with one RGMII and one RMII interface.
3. Added dt-bindings for the GMAC interfaces.
====================
Link: https://patch.msgid.link/20260323101756.81849-1-a0987203069@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for Gigabit Ethernet on Nuvoton MA35 series using dwmac driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joey Lu <a0987203069@gmail.com>
Link: https://patch.msgid.link/20260323101756.81849-4-a0987203069@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create initial schema for Nuvoton MA35 family Gigabit MAC.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Joey Lu <a0987203069@gmail.com>
Link: https://patch.msgid.link/20260323101756.81849-2-a0987203069@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- virt_wifi: remove SET_NETDEV_DEV to avoid UAF on teardown
- iwlwifi:
- fix (some) devices that don't have 6 GHz (WiFi6E)
- fix potential OOB read of firmware notification
- set WiFi generation for firmware to avoid packet drops
- fix multi-link scan timing
- wilc1000: fix integer overflow
- ath11k/ath12k: fix TID during A-MPDU session teardown
- wl1251: don't trust firmware TX status response index
-----BEGIN PGP SIGNATURE-----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=eTfp
-----END PGP SIGNATURE-----
Merge tag 'wireless-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Couple more fixes:
- virt_wifi: remove SET_NETDEV_DEV to avoid UAF on teardown
- iwlwifi:
- fix (some) devices that don't have 6 GHz (WiFi6E)
- fix potential OOB read of firmware notification
- set WiFi generation for firmware to avoid packet drops
- fix multi-link scan timing
- wilc1000: fix integer overflow
- ath11k/ath12k: fix TID during A-MPDU session teardown
- wl1251: don't trust firmware TX status response index
* tag 'wireless-2026-03-26' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free
wifi: iwlwifi: mvm: fix potential out-of-bounds read in iwl_mvm_nd_match_info_handler()
wifi: wl1251: validate packet IDs before indexing tx_frames
wifi: wilc1000: fix u8 overflow in SSID scan buffer size calculation
wifi: ath12k: Pass the correct value of each TID during a stop AMPDU session
wifi: ath11k: Pass the correct value of each TID during a stop AMPDU session
wifi: iwlwifi: mld: correctly set wifi generation data
wifi: iwlwifi: mvm: don't send a 6E related command when not supported
wifi: iwlwifi: mld: Fix MLO scan timing
====================
Link: https://patch.msgid.link/20260326093329.77815-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit c50dcf5331.
The tests are superficial, likely AI-generated slop, and flaky. They
don't add actual value and just churn the selftests.
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 9edd04c418.
The doc-only change is insufficient. The actual fix requires bumping the
minimum pahole version to 1.27 with proper Kconfig and Makefile.btf
changes, and should be routed through the BPF tree.
Link: https://lore.kernel.org/all/e0ca748d-3204-4160-b37d-0f76cbac8c6c@linux.dev
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the Tegra410 SoC, which has 4 I2C controllers. The
controllers are feature-equivalent to Tegra264; only the register
offsets differ.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-4-kkartik@nvidia.com
Tegra410 use different offsets for existing I2C registers, update
the logic to use appropriate offsets per SoC.
As the register offsets are now defined in the SoC-specific
tegra_i2c_regs structures, the tegra_i2c_reg_addr() function is no
longer needed to translate register offsets and has been removed.
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-3-kkartik@nvidia.com
Replace the per-instance DVC/VI boolean flags with a tegra_i2c_variant
enum and move the variant field into tegra_i2c_hw_feature so it is
populated via SoC match data.
Add dedicated SoC data entries for the "nvidia,tegra20-i2c-dvc" and
"nvidia,tegra210-i2c-vi" compatibles and drop compatible-string checks
from tegra_i2c_parse_dt.
Suggested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Kartik Rajput <kkartik@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20260324055843.549808-2-kkartik@nvidia.com
Add a compatible string for the I2C controller found in SpacemiT K3 SoC
which use same I2C IP as K1, so make it fallback to K1 compatible.
Signed-off-by: Yixun Lan <dlan@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.spacemit.com>
Link: https://lore.kernel.org/r/20260325-02-k3-i2c-v1-1-78f29c83d9ac@kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
The "comm" column allows grouping events by the process command. It is
intended to group like programs, despite having different PIDs. But some
workloads may adjust their own command, so that a unique identifier
(e.g. a PID or some other numeric value) is part of the command name.
This destroys the utility of "comm", forcing perf to place each unique
process name into its own bucket, which can contribute to a
combinatorial explosion of memory use in perf report.
Create a less strict version of this column, which ignores digits when
comparing command names. Commands whose names are the same (ignoring
digits) are sorted into the same histogram buckets, and displayed with
the placeholder value "<N>" in the place of digits. For example,
hypothetical command names "kworker/1" "kworker/2" "kworker/3" would
sort into the same bucket and be represented as "kworker/<N>".
Committer testing:
$ perf report -s comm,comm_nodigit | grep -F "<N>"
0.01% CPU 6/TCG CPU <N>/TCG
0.01% kworker/53:2-mm kworker/<N>:<N>-mm
0.01% migration/24 migration/<N>
0.01% kworker/24:1-ev kworker/<N>:<N>-ev
0.01% llvmpipe-8 llvmpipe-<N>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
