The interpreters_args array only accommodates stack depths up to
MAX_BPF_STACK (512 bytes). However, do_misc_fixups() may allow a larger
stack depth if JIT is requested.
If JIT compilation later fails and falls back to the interpreter, the
verifier invokes bpf_patch_call_args() with this oversized stack depth.
This causes a load-time out-of-bounds (OOB) read when calculating the
interpreter function pointer index.
Fix this by changing bpf_patch_call_args() to return an int and explicitly
rejecting the JIT fallback (returning -EINVAL) if the stack depth exceeds
MAX_BPF_STACK.
Fixes: 1ea47e01ad ("bpf: add support for bpf_call to interpreter")
Co-developed-by: Tianci Cao <ziye@zju.edu.cn>
Signed-off-by: Tianci Cao <ziye@zju.edu.cn>
Co-developed-by: Shenghao Yuan <shenghaoyuan0928@163.com>
Signed-off-by: Shenghao Yuan <shenghaoyuan0928@163.com>
Signed-off-by: Yazhou Tang <tangyazhou518@outlook.com>
Acked-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20260506094714.419842-2-tangyazhou@zju.edu.cn
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When uart_flush_buffer() runs before the DMA completion IRQ is delivered,
the following race can occur (all steps serialized by uart_port_lock):
1. DMA starts: tx_remaining = N, kfifo contains N bytes
2. DMA completes in hardware; IRQ is pending but not yet delivered
3. uart_flush_buffer() acquires the port lock and calls kfifo_reset(),
making kfifo_len() = 0 while tx_remaining remains N
4. uart_flush_buffer() releases the port lock
5. DMA IRQ fires; handle_tx_dma() acquires the port lock and calls
uart_xmit_advance(uport, tx_remaining) on an empty kfifo
uart_xmit_advance() increments kfifo->out by tx_remaining. Since
kfifo_reset() already set both in and out to 0, out wraps past in,
causing kfifo_len() to return UART_XMIT_SIZE - tx_remaining. The next
start_tx_dma() call then submits a DMA transfer of stale buffer data.
Fix this by snapshotting kfifo_len() at the start of handle_tx_dma()
and skipping uart_xmit_advance() when fifo_len < tx_remaining, which
indicates the kfifo was reset by a preceding flush.
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260506-serial-dma-stale-tx-buf-v1-1-e3ccb360d719@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart_start_rx_dma() allocates sport->rx_ring.buf with kzalloc() and
then maps a scatterlist via dma_map_sg(). On three subsequent error
paths the function returns directly without releasing those resources:
- when dma_map_sg() returns 0 (-EINVAL):
ring->buf is leaked.
- when dmaengine_slave_config() fails:
ring->buf and the DMA mapping are leaked.
- when dmaengine_prep_dma_cyclic() returns NULL:
ring->buf and the DMA mapping are leaked.
The sole cleanup path, lpuart_dma_rx_free(), is only reached when
lpuart_dma_rx_use is set, and the caller lpuart_rx_dma_startup() clears
that flag on failure of lpuart_start_rx_dma(). So these resources are
permanently leaked on every failure in this function. Repeated port
open/close or termios changes under error conditions will slowly consume
memory and leave stale streaming DMA mappings behind.
Fix it by introducing two error labels that unmap the scatterlist and
free the ring buffer as appropriate. While here, replace the misleading
-EFAULT (bad userspace pointer) returned when dmaengine_prep_dma_cyclic()
fails with the more accurate -ENOMEM, matching how other dmaengine users
in the tree treat this failure.
No functional change on the success path.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Cc: stable <stable@kernel.org>
Signed-off-by: Shitalkumar Gandhi <shitalkumar.gandhi@cambiumnetworks.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260420135903.2062024-1-shitalkumar.gandhi@cambiumnetworks.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7f991e3f9b ("nvme: add quirk
NVME_QUIRK_IGNORE_DEV_SUBNQN for 144d:a808")
The incorrect implementations of SUBNQN is a known issue in a massive number of
NVMe units. However, the warning "nvme nvmex: missing or invalid SUBNQN field."
is usually appropriate and will not affect performance or behavior etc. That is
because the support for SUBNQN is mandatory if the controller supports NVMe
revision 1.2.1 or greater, and it reported itself without a SUBNQN field which
breaks compliance with the specification. It should be not quirked by the Linux
Kernel.
Signed-off-by: Alan Cui <me@alancui.cc>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Shivam Kumar found via vulnerability testing:
When data digest is enabled on an NVMe/TCP connection and a digest
mismatch occurs on a non-final H2C_DATA PDU during an R2T-based
data transfer, the digest error handler in nvmet_tcp_try_recv_ddgst()
calls nvmet_req_uninit() — which performs percpu_ref_put() on the
submission queue — but does NOT mark the command as completed. It
does not set cqe->status, does not modify rbytes_done, and does not
clear any flag. When the subsequent fatal error triggers queue
teardown, nvmet_tcp_uninit_data_in_cmds() iterates all commands,
checks nvmet_tcp_need_data_in() for each one, and finds that the
already-uninited command still appears to need data (because
rbytes_done < transfer_len and cqe->status == 0). It therefore calls
nvmet_req_uninit() a second time on the same command — a double
percpu_ref_put against a single percpu_ref_get.
Reported-by: Shivam Kumar <kumar.shivam43666@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
nvme_free_host_mem() frees dev->hmb_sgt via dma_free_noncontiguous()
but never clears the pointer afterward. This leads to a use-after-free
if nvme_free_host_mem() is called twice in the same error path.
This can happen during nvme_probe() when nvme_setup_host_mem() succeeds
in allocating the HMB (setting dev->hmb_sgt) but nvme_set_host_mem()
fails with an I/O error:
nvme_setup_host_mem()
nvme_alloc_host_mem_single() -> sets dev->hmb_sgt
nvme_set_host_mem() -> fails with -EIO
nvme_free_host_mem() -> frees hmb_sgt, but does NOT NULL it
return error
nvme_probe() error path:
nvme_free_host_mem() -> dev->hmb_sgt is stale, use-after-free
The second call dereferences the freed sgt, causing a NULL pointer
dereference in iommu_dma_free_noncontiguous() when it accesses
sgt->sgl->dma_address (the backing memory has been freed and zeroed).
This is reproducible on Thunderbolt-attached NVMe devices (e.g., OWC
Envoy Express behind a Dell WD22TB4 dock) where the device intermittently
returns I/O errors during HMB setup due to PCIe link instability.
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:iommu_dma_free_noncontiguous+0x22/0x80
Call Trace:
<TASK>
dma_free_noncontiguous+0x3b/0x130
nvme_free_host_mem+0x30/0xf0 [nvme]
nvme_probe.cold+0xcc/0x275 [nvme]
local_pci_probe+0x43/0xa0
pci_device_probe+0xeea/0x290
really_probe+0xf9/0x3b0
__driver_probe_device+0x8b/0x170
driver_probe_device+0x24/0xd0
__driver_attach_async_helper+0x6b/0x110
async_run_entry_fn+0x37/0x170
process_one_work+0x1ac/0x3d0
worker_thread+0x1b8/0x360
kthread+0xf7/0x130
ret_from_fork+0x2d8/0x3a0
ret_from_fork_asm+0x1a/0x30
</TASK>
Fix this by setting dev->hmb_sgt to NULL after freeing it, so the
second call takes the multi-descriptor path which safely handles the
already-cleaned-up state.
Fixes: 63a5c7a4b4 ("nvme-pci: use dma_alloc_noncontigous if possible")
Signed-off-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
From a security standpoint we should not allow to print out the DH-HMAC-CHAP
secrets, but at the same time having them is useful for debugging
authentication failures.
So add a Kconfig option NVME_TARGET_AUTH_DEBUG to only enable debugging
if explictly requested at build time.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Hannes Reinecke <hare@kernel.org>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The local bio is always NULL, so we'd leak the bio if the integrity
mapping failed. Just get it directly from the request.
Fixes: d0d1d52231 ("blk-map: provide the bdev to bio if one exists")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
The warning is a bit alarming, and it only prints for the very first
non-sgl capable device that receives a passthrough command. Just log an
informational message on initial discovery for every device.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Include the definition of struct tty_driver in tty_port.h to keep the
header self-contained and avoid build breakage in case anyone includes
it before tty_driver.h.
Fixes: eb3b0d92c9 ("tty: tty_port: add workqueue to flip TTY buffer")
Cc: Xin Zhao <jackzxcui1989@163.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://patch.msgid.link/20260506124323.186703-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_RX_PAR_EN is incorrectly defined as bit 3, which triggers false
framing errors (S_GP_IRQ_1_EN) and causes received data to be dropped
when parity is enabled and the parity bit is 0.
Define UART_RX_PAR_EN as bit 4 of the SE_UART_RX_TRANS_CFG register, as
specified in the reference manual.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable <stable@kernel.org>
Signed-off-by: Prasanna S <prasanna.s@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://patch.msgid.link/20260428-serial-bit-correct-v1-1-9131ad5b97d8@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sci_request_port() function uses request_mem_region() to reserve
I/O memory, but in the error path when sci_remap_port() fails, it
incorrectly calls release_resource() instead of release_mem_region().
This mismatch can cause resource accounting issues. Fix it by using
the correct release function, consistent with sci_release_port().
Fixes: e265164708 ("serial: sh-sci: Handle port memory region reservations.")
Cc: stable <stable@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202604032356.SzEjYkBC-lkp@intel.com/
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260421065737.724187-1-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for dma_alloc_coherent() failure to prevent a potential
NULL pointer dereference in dma_handle_rx(). Properly release DMA
channels and the PCI device reference using a goto ladder if the
allocation fails.
Fixes: 3c6a483275 ("Serial: EG20T: add PCH_UART driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Zhaoyang Yu <2426767509@qq.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/tencent_E328416B7CFD436F6029F2DF02AD7ED89C08@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a thinko in the status interrupt handler that has caused counters
for the RI and DSR modem line transitions to be used for the other line
each.
Fixes: 8b4a40809e ("zs: move to the serial subsystem")
Cc: stable <stable@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://patch.msgid.link/alpine.DEB.2.21.2604101747110.29980@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the fixed-emmc-driver-type device tree property, the MMC core
correctly selects the driver strength for the card but fails to program
the host controller accordingly. This causes a mismatch where the card
uses the specified driver type while the host controller defaults to
Type B (since ios->drv_type remains zero).
Split the driver type programming logic to handle both fixed and dynamic
driver type selection paths. For fixed driver types, program the host
controller with the selected drive_strength value. For dynamic selection,
use the existing drv_type as before.
This ensures both the eMMC device and host controller use matching driver
strengths, preventing potential signal integrity issues.
Fixes: 6186d06c51 ("mmc: parse new binding for eMMC fixed driver type")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
check_mft_mirror() still computes the number of bytes to validate in each
mirrored MFT record, but the actual comparison against $MFTMirr was dropped
when the superblock code was updated.
As a result, mount misses a stale or inconsistent $MFTMirr as long as both
records pass the structural baad-record checks. Restore the comparison and
log an error when the primary $MFT record differs from its mirror copy.
Returning false lets the existing mount error handling mark the volume as
having NTFS errors and, with on_errors=remount-ro, continue read-only. The
default on_errors=continue mount policy still allows the mount to proceed.
Fixes: 6251f0b0de ("ntfs: update super block operations")
Signed-off-by: DaeMyung Kang <charsyam@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via
run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0.
After irq_work_single() clears BUSY via atomic_cmpxchg(), it still
dereferences @work for irq_work_is_hard() and rcuwait_wake_up().
An irq_work_sync() caller on another CPU that enters after BUSY is cleared
can observe BUSY==0 immediately, return, and free the work before those
accesses complete — causing a use-after-free.
Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire
irq_work_single() execution is within an RCU read-side critical
section. Then add synchronize_rcu() in irq_work_sync() after
rcuwait_wait_event() to ensure the caller waits for the RCU grace period
before returning, preventing premature frees.
Fixes: 810979682c ("irq_work: Allow irq_work_sync() to sleep if irq_work() no IRQ support.")
Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20260330073234.303732-1-jiayuan.chen@linux.dev
Use the existing zenbook duo keyboard quirk for the UX8407AA model too.
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Reviewed-by: Denis Benato <denis.benato@linux.dev>
Link: https://patch.msgid.link/20260508070956.62201-1-p.pisati@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Since Qualcomm inline-crypto engine (ICE) is now a dedicated driver
de-coupled from the QCOM UFS driver, it explicitly votes for its required
clocks during probe. For scenarios where the 'clk_ignore_unused' flag is
not passed on the kernel command line, to avoid potential unclocked ICE
hardware register access during probe the ICE driver should additionally
vote on the 'iface' clock.
Also update the suspend and resume callbacks to handle un-voting and voting
on the 'iface' clock.
Fixes: 2afbf43a4a ("soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver")
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-2-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The DT bindings for inline-crypto engine do not specify the UFS_PHY_GDSC
power-domain and iface clock. Without enabling the iface clock and the
associated power-domain the ICE hardware cannot function correctly and
leads to unclocked hardware accesses being observed during probe.
Fix the DT bindings for inline-crypto engine to require the UFS_PHY_GDSC
power-domain and iface clock for new devices (Eliza and Milos) introduced
in the current release (7.1) with yet-to-stabilize ABI, while preserving
backward compatibility for older devices.
Fixes: 618195a7ac ("dt-bindings: crypto: qcom,inline-crypto-engine: Document the Eliza ICE")
Fixes: 85faec1e85 ("dt-bindings: crypto: qcom,inline-crypto-engine: document the Milos ICE")
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-1-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Machines with a larger number of CPUs and under heavy load sometimes
loose PAI counter increments during recording using events
-e CRYPTO_ÂLL or -e NNPA_ALL. Counting is not affected.
This happens when several PAI crypto counters are incremented during
the same cryptographic operation.
During schedule out the functions
paiXXX_sched_task() (with XXX either crypt or ext)
+--> pai_have_samples()
+--> pai_have_sample()
+--> pai_copy()
+--> pai_push_sample()
are called to read out PAI counter values.
In pai_copy() the current values of PAI counters are read from the
PMU memory mapped page and compared to the values read during last
schedule out operation, which have been saved in a backup page
named PAI_SAVE_AREA(event). For each PAI counter a delta is calculated
and when the delta is positive, that PAI counter was incremented by
hardware. This positve delta is reported as raw data record attached
to a sample.
After all deltas have been calculated, the new PAI counter values
are saved in the backup page PAI_SAVE_AREA(event). However this is
done in pai_push_sample(), leaving a small window for missing hardware
triggered updates. Here is one scenario:
PAI counter idx: 0 1 2 3 4 5 6 7 .... N
+---+---+---+---+---+---+---+---+ +---+
PAI counter page:| | | X | | | | | |....| Y |
+---+---+---+---+---+---+---+---+ +---+
In pai_copy() each PAI counter value is read and compared
to its old value. This is done in a loop. When PAI counter indexed
N is read, the hardware might increment PAI counter indexed 2 again,
updating its value from X to X+1.
Later pai_push_sample() simply mem-copies the complete PAI counter
page to a backup page and the increment of X+1 is lost, because the
backup page now contains the new value.
Read each PAI counter and save this value in the backup page when
there is a positive delta. This omits any time window between read
and store. This also reduced the work load as only modified PAI
counters are saved.
Cc: stable@vger.kernel.org
Fixes: fe861b0c8d ("s390/pai: save PAI counter value page in event structure")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
When executing NS_GET_PID_FROM_PIDNS (or similar pidns ioctls), if the
target task cannot be found in the corresponding pid_ns, the error code
should be ESRCH instead of ENOTTY.
This bug was introduced when the extensible ioctl handling was added.
Without proper return, ret would be overwritten by the default case in
the extensible ioctl switch statement.
Fixes: a1d220d9da ("nsfs: iterate through mount namespaces")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://patch.msgid.link/20260507112301.1042757-1-chengzhihao1@huawei.com
Reviewed-by: Yang Erkun <yangerkun@huawei.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
blk_validate_limits() requires max_hw_sectors >= PAGE_SECTORS and fires
a WARN_ON_ONCE if this invariant is violated. ublk_validate_params()
only checked the upper bound of max_sectors against max_io_buf_bytes,
allowing userspace to pass small values (including zero) that trigger
the warning when blk_mq_alloc_disk() is called from
ublk_ctrl_start_dev().
Before 494ea040bc, ublk used blk_queue_max_hw_sectors() which silently
clamped small values up to PAGE_SECTORS. The conversion to passing
queue_limits directly to blk_mq_alloc_disk() lost that clamping and now
hits blk_validate_limits()'s WARN_ON_ONCE instead.
Validate that max_sectors is at least PAGE_SECTORS in
ublk_validate_params() so invalid values are rejected early with
-EINVAL instead of reaching the block layer.
Fixes: 494ea040bc ("ublk: pass queue_limits to blk_mq_alloc_disk")
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Link: https://patch.msgid.link/20260510144843.769031-1-tom.leiming@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
SQPOLL stores current->pid (init_pid_ns view) in sqd->task_pid
at thread creation. fdinfo prints it raw via
seq_printf("SqThread:\t%d\n", sq_pid). A reader inside a
non-initial pid_ns sees the host PID, not the kthread's PID in
the reader's own pid_ns.
The SQPOLL kthread is created with CLONE_THREAD and no
CLONE_NEW*, so it lives in the submitter's pid_ns. An
unprivileged user_ns + pid_ns submitter can read fdinfo and
learn the host PID of a kthread whose in-namespace PID is
different.
Reproducer (mainline 7.0, KASAN): unshare CLONE_NEWUSER |
CLONE_NEWPID | CLONE_NEWNS, mount a private /proc, then have a
grandchild that is pid 1 in the new pid_ns open an io_uring
ring with IORING_SETUP_SQPOLL. /proc/self/task lists {1, 2};
the SQPOLL kthread is pid 2. Before: fdinfo prints
SqThread = <host pid>. After: SqThread = 2.
Use task_pid_nr_ns() against the proc inode's pid_ns to compute
sq_pid, instead of reading the stored sq->task_pid (which holds
the init_pid_ns view). pidfd_show_fdinfo() in kernel/pid.c
follows the same pattern.
Signed-off-by: Maoyi Xie <maoyi.xie@ntu.edu.sg>
Link: https://patch.msgid.link/20260510084119.457578-1-maoyi.xie@ntu.edu.sg
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When updating timestamps with lazytime enabled, if only I_DIRTY_TIME is
set (pure lazytime update), inode_maybe_inc_iversion() should not be
forced to increment i_version. The force parameter should only be true
when actual data or metadata changes require an iversion bump.
The current code uses "!!dirty" which evaluates to true whenever dirty
has any bits set, including the I_DIRTY_TIME bit alone. This forces an
iversion increment on every lazytime timestamp update, which then sets
I_DIRTY_SYNC, triggering expensive log flushes on subsequent fdatasync
calls. Andres reported this issue when he noticed a perf regression[1].
Fix this by using "dirty != I_DIRTY_TIME" as the force parameter. This
passes false for pure lazytime updates (allowing the I_VERSION_QUERIED
optimization to work), while still forcing the increment when dirty
contains other flags indicating real changes that require iversion
updates.
[1] https://lore.kernel.org/linux-xfs/7ys6erh3nnyeerv2nybyfvp7dmaknuxrlxv74wx56ocdothkc6@ekfiadtkfn2r/
Fixes: 85c871a02b ("fs: add support for non-blocking timestamp updates")
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Link: https://patch.msgid.link/20260511111918.1793689-1-p.raghav@samsung.com
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Affinity changes of IMSIC interrupts have to be careful to not lose an
interrupt in the process. Each vector keeps track of an affinity change in
progress with two pointers in struct imsic_vector.
imsic_vector::move_prev points to the previous CPU target data and
imsic_vector::move_next to the designated new CPU target data.
imsic_vector::move_prev on the new CPU can only be cleared after the
previous CPU has cleared imsic_vector::move_next, which ususally happens in
__imsic_remote_sync().
In case of CPU hot-unplug __imsic_remote_sync() is not invoked because the
CPU is already marked offline. That means imsic_vector::move_prev becomes
stale until the CPU is onlined again.
The stale pointer prevents further affinity changes for the affected
interrupts.
Solve this by clearing the imsic_vector::move_prev pointers in the CPU
hotplug offline path.
[ tglx: Replace word salad in change log ]
Fixes: 0f67911e82 ("irqchip/riscv-imsic: Separate next and previous pointers in IMSIC vector")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260508-imsic-v2-1-e9f08dd46cf5@sifive.com
meson_s4_gpio_irq_set_type() uses the both-edge trigger register for
configuring level type and single edge mode interrupts, which is not
correct.
Use REG_EDGE_POL instead.
Fixes: bbd6fcc76b ("irqchip: Add support for Amlogic A4 and A5 SoCs")
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260508-a9-gpio-irqchip-v1-1-9dc5f3e022e0@amlogic.com
Recently handle_percpu_devid_irq() was changed to call
add_interrupt_randomness(). This introduced a potential deadlock when
handle_percpu_devid_irq() is used to handle an NMI, which can be
detected with lockdep, e.g.
================================
WARNING: inconsistent lock state
7.1.0-rc2-pnmi #465 Not tainted
--------------------------------
inconsistent {INITIAL USE} -> {IN-NMI} usage.
perf/695 [HC1[1]:SC0[0]:HE0:SE1] takes:
ffff00837dfd3a18 (&base->lock){-.-.}-{2:2}, at: lock_timer_base+0x6c/0xac
{INITIAL USE} state was registered at:
_raw_spin_lock_irqsave+0x68/0xb0
lock_timer_base+0x6c/0xac
__mod_timer+0x100/0x32c
add_timer_global+0x2c/0x40
__queue_delayed_work+0xf0/0x140
queue_delayed_work_on+0x134/0x138
mem_cgroup_css_online+0x30c/0x310
online_css+0x34/0x10c
cgroup_init_subsys+0x158/0x1c8
cgroup_init+0x440/0x524
start_kernel+0x888/0x998
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&base->lock);
<Interrupt>
lock(&base->lock);
*** DEADLOCK ***
Call trace:
_raw_spin_lock_irqsave+0x68/0xb0
lock_timer_base+0x6c/0xac
add_timer_on+0x78/0x16c
add_interrupt_randomness+0x124/0x134
handle_percpu_devid_irq+0xd4/0x16c
handle_irq_desc+0x40/0x58
generic_handle_domain_nmi+0x28/0x50
__gic_handle_nmi.isra.0+0x4c/0xa0
gic_handle_irq+0x38/0x2bc
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x98
el1_interrupt+0x90/0xac
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x80/0x84
[...]
During review, Thomas pointed out it wouldn't be safe for
handle_percpu_devid_irq() to call add_interrupt_randomness() if it was
used to handle NMIs:
https://lore.kernel.org/lkml/87bjgik042.ffs@tglx/
... but evidently people missed that handle_percpu_devid_irq() *is* used
for NMIs.
While it might seem that NMIs should be handled with a separate
handle_percpu_devid_nmi() function, for various structural reasons this was
impractical, and handle_percpu_devid_irq() has been expected to be used for
NMIs since commits:
21bbbc50f3 ("irqchip/gic-v3: Switch high priority PPIs over to handle_percpu_devid_irq()")
5ff78c8de9 ("genirq: Kill handle_percpu_devid_fasteoi_nmi()")
Taking the above into account, avoid the deadlock by not calling
add_interrupt_randomness() when handle_percpu_devid_irq() is called in an
NMI context. This is consistent with other NNI handling flows, which do not
call add_interrupt_randomness().
At the same time, update the kernel-doc comment to make it clear that
handle_percpu_devid_irq() can be called in NMI context. The rest of
handle_percpu_devid_irq() is currently NMI safe and doesn't need to change.
Fixes: fd7400cfcb ("genirq/chip: Invoke add_interrupt_randomness() in handle_percpu_devid_irq()")
Reported-by: Ada Couprie Diaz <ada.coupriediaz@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://patch.msgid.link/20260507110518.3128248-1-mark.rutland@arm.com
The ITS MSI domain no longer manages LPI allocation directly. LPIs are
allocated and freed by the parent LPI domain, which can now handle a
full range of interrupts and unwind partial allocations internally.
Make the ITS domain request and release the parent IRQs as a single
range instead of iterating over each interrupt. The ITS allocation
path then only needs to reserve EventIDs, allocate the parent range,
and fill in the ITS irq_data for each MSI. Since no operation in the
per-MSI loop can fail, the partial parent-free unwind becomes
unnecessary.
On teardown, reset the ITS irq_data for the range and then release the
parent range in one call, leaving LPI teardown to the LPI domain.
Fixes: 0f01013258 ("irqchip/gic-v5: Add GICv5 LPI/IPI support")
Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260506093634.382062-4-sascha.bischoff@arm.com
The per-IPI parent allocation loop returns immediately on failure and leaks
any parent interrupts allocated by earlier iterations.
The GICv5 LPI domain now owns LPI allocation and teardown internally,
but its irq_domain callbacks still reject requests where nr_irqs is
greater than one. This forces child domains to allocate and free LPIs
one at a time even when the interrupt core requests a contiguous
range.
Handle multi-interrupt allocation and teardown in the LPI domain by
iterating over the requested range and unwinding any partially
allocated state on failure.
Allocate the parent LPIs for the IPI domain with a single range
request as well, which cures the leakage problem.
Fixes: 0f01013258 ("irqchip/gic-v5: Add GICv5 LPI/IPI support")
Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260506093634.382062-3-sascha.bischoff@arm.com
The IPI and ITS MSI domains currently allocate and release LPIs
directly, then pass the selected LPI ID to the parent LPI domain. This
leaks the LPI domain's allocation policy into its child domains and
forces each child to duplicate part of the parent domain's teardown.
Make the LPI domain allocate LPIs in its .alloc() callback and release
them in a matching .free() callback. Child domains can then request a
parent interrupt without passing an implementation-specific LPI ID,
and the LPI lifetime is tied to the domain that owns the LPI
namespace.
Remove the gicv5_alloc_lpi() and gicv5_free_lpi() wrappers now that no
external caller needs to manage LPIs directly.
This is a preparatory change for an actual leakage problem in the
allocation code and therefore tagged with the same Fixes tag.
Fixes: 0f01013258 ("irqchip/gic-v5: Add GICv5 LPI/IPI support")
Signed-off-by: Sascha Bischoff <sascha.bischoff@arm.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260506093634.382062-2-sascha.bischoff@arm.com
fuse_iomap_writeback_range() appends one folio pointer and one
fuse_folio_desc for every dirty range that is merged into the current
writeback request. The merge decision checks the byte budget against
fc->max_pages and fc->max_write, but it does not check whether the folio
and descriptor arrays still have another free slot.
This is not sufficient for fuseblk, where the filesystem block size can
be smaller than PAGE_SIZE. With writeback cache enabled and max_pages
negotiated as one, contiguous sub-page dirty ranges can fit within the
byte budget while spanning more than one folio. The next append can then
write past the one-slot folios and descs arrays.
Split the request when the number of already attached folios has reached
fc->max_pages. This keeps the folio/descriptor slot accounting in sync
with the send decision.
Fixes: ef7e7cbb32 ("fuse: use iomap for writeback")
Cc: stable@vger.kernel.org
Reviewed-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Junxi Qian <qjx1298677004@gmail.com>
Link: https://patch.msgid.link/20260506122415.205340-1-qjx1298677004@gmail.com
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Return NULL instead of passing to ERR_PTR while err is zero
Fixes these smatch warnings:
- fs/jfs/namei.c:311 jfs_mkdir() warn: passing zero to 'ERR_PTR'
- fs/orangefs/namei.c:369 orangefs_mkdir() warn: passing zero
to 'ERR_PTR'
Fixes: 88d5baf690 ("Change inode_operations.mkdir to return struct dentry *")
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://patch.msgid.link/20260501071058.1243245-1-zenghongling@kylinos.cn
Reviewed-by: Jori Koolstra <jkoolstra@xs4all.nl>
Signed-off-by: Christian Brauner <brauner@kernel.org>
statmount_mnt_idmap() writes one mapping with seq_printf() and then
manually advances seq->count to include the NUL separator.
If seq_printf() overflows, seq_set_overflow() sets seq->count to
seq->size. The manual seq->count++ changes this to seq->size + 1.
seq_has_overflowed() then no longer detects the overflow. The corrupted
count returns to statmount_string(), which later executes:
seq->buf[seq->count++] = '\0';
This causes a 1-byte NULL out-of-bounds write on the dynamically
allocated seq buffer.
Fix this by checking for overflow immediately after seq_printf().
Fixes: 37c4a9590e ("statmount: allow to retrieve idmappings")
Signed-off-by: Junyoung Jang <graypanda.inzag@gmail.com>
Link: https://patch.msgid.link/20260504112649.1862936-1-graypanda.inzag@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Adds lwmi_is_attr_01_supported, and only creates the attribute subfolder
if the attribute is supported by the hardware. Due to some poorly
implemented BIOS this is a multi-step sequence of events. This is
because:
- Some BIOS support getting the capability data from custom mode (0xff),
while others only support it in no-mode (0x00).
- Some BIOS support get/set for the current value from custom mode (0xff),
while others only support it in no-mode (0x00).
- Some BIOS report capability data for a method that is not fully
implemented.
- Some BIOS have methods fully implemented, but no complimentary
capability data.
To ensure we only expose fully implemented methods with corresponding
capability data, we check each outcome before reporting that an
attribute can be supported.
Checking for lwmi_is_attr_01_supported during remove is not done to
ensure that we don't attempt to call cd01 or send WMI events if one of
the interfaces being removed was the cause of the driver unloading.
Fixes: edc4b183b7 ("platform/x86: Add Lenovo Other Mode WMI Driver")
Reported-by: Kurt Borja <kuurtb@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/DG60P3SHXR8H.3NSEHMZ6J7XRC@gmail.com/
Cc: stable@vger.kernel.org
Reviewed-by: Rong Zhang <i@rong.moe>
Tested-by: Rong Zhang <i@rong.moe>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-10-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Adds lwmi_attr_id() function. In the same vein as LWMI_ATTR_ID_FAN_RPM(),
but as a generic, to de-duplicate attribute_id assignment boilerplate.
Adds tunable_attr_01_id() function that breaks out the members of a
tunable_attr_01 struct and passes them to lwmi_attr_id().
No functional change intended.
Cc: stable@vger.kernel.org
Reviewed-by: Rong Zhang <i@rong.moe>
Tested-by: Rong Zhang <i@rong.moe>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-9-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
In a later patch in the series the thermal mode enum will be accessed
across three separate drivers (wmi-capdata, wmi-gamezonem and wmi-other).
An additional patch in the series will also add a function prototype that
needs to reference this enum in wmi-helpers.h. To avoid having all these
drivers begin to import each others headers, and to avoid declaring an
opaque enum to hande the second case, move the thermal mode enum to
helpers where it can be safely accessed by everything that needs it from
a single import.
While at it, since the gamezone_events_type enum is the only remaining
item in the header, move that as well and remove the gamezone header
entirely.
Cc: stable@vger.kernel.org
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Rong Zhang <i@rong.moe>
Tested-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-8-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Currently, lenovo-wmi-gamezone depends on lenovo-wmi-other as the former
imports symbols from the latter. The imported symbols are just used to
register a notifier block. However, there is no runtime dependency
between both drivers, and either of them can run without the other,
which is the major purpose of using the notifier framework.
Such a link-time dependency is non-optimal. A previous attempt to "fix"
it made LENOVO_WMI_GAMEZONE select LENOVO_WMI_TUNING, which was
fundamentally broken and resulted in undefined Kconfig behavior, as
`select' cannot be used on a symbol with potentially unmet dependencies.
Decouple both drivers by moving the thermal mode notifier chain to
lenovo-wmi-helpers. Methods for notifier block (un)registration are
exported for lenovo-wmi-gamezone, while a method for querying the
current thermal mode are exported for lenovo-wmi-other.
This turns the dependency graph from
+------------ lenovo-wmi-gamezone
| |
v |
lenovo-wmi-helpers |
^ |
| V
+------------ lenovo-wmi-other
into
+------------ lenovo-wmi-gamezone
|
v
lenovo-wmi-helpers
^
|
+------------ lenovo-wmi-other
To make it clear, the name of the notifier chain is also renamed from
`om_chain_head' to `tm_chain_head', indicating that it's used to query
the current thermal mode.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Fixes: 6e38b9fcbf ("platform/x86: lenovo: gamezone needs "other mode"")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202603252259.gHvJDyh3-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202603260302.X0NjQOda-lkp@intel.com/
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-7-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
In struct tunable_attr_01 the capdata pointer is unused and the size of
the id members is u32 when it should be u8. Fix these prior to adding
additional members.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Cc: stable@vger.kernel.org
Reviewed-by: Rong Zhang <i@rong.moe>
Tested-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-6-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Adds explicit initialization of wmi_method_args_32 declarations with
zero values to prevent uninitialized data from being sent to the device
BIOS when passed.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Fixes: 22024ac536 ("platform/x86: Add Lenovo Gamezone WMI Driver")
Fixes: edc4b183b7 ("platform/x86: Add Lenovo Other Mode WMI Driver")
Reported-by: Rong Zhang <i@rong.moe>
Closes: https://lore.kernel.org/platform-driver-x86/95c7e7b539dd0af41189c754fcd35cec5b6fe182.camel@rong.moe/
Cc: stable@vger.kernel.org
Reviewed-by: Rong Zhang <i@rong.moe>
Tested-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-5-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
When lwmi_om_master_bind() fails, the master device's components are
left bound, with the aggregate device destroyed due to the failure
(found by sashiko.dev [1]).
Balance calls to component_bind_all() and component_unbind_all() when an
error is propagated to the component framework.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Fixes: edc4b183b7 ("platform/x86: Add Lenovo Other Mode WMI Driver")
Cc: stable@vger.kernel.org
Link: https://sashiko.dev/#/patchset/20260331181208.421552-1-derekjohn.clark%40gmail.com [1]
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-4-derekjohn.clark@gmail.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Currently, the IDA id is only freed on wmi-other device removal or
failure to create firmware-attributes device, kset, or attributes. It
leaks IDA ids if the wmi-other device is bound multiple times, as the
unbind callback never frees the previously allocated IDA id.
Additionally, if the wmi-other device has failed to create a
firmware-attributes device before it gets removed, the wmi-device
removal callback double frees the same IDA id.
These bugs were found by sashiko.dev [1].
Fix them by moving ida_free() into lwmi_om_fw_attr_remove() so it is
balanced with ida_alloc() in lwmi_om_fw_attr_add(). With them fixed,
properly set and utilize the validity of priv->ida_id to balance
firmware-attributes registration and removal, without relying on
propagating the registration error to the component framework, which is
more reliable and aligns with the hwmon device registration and removal
sequences.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Fixes: edc4b183b7 ("platform/x86: Add Lenovo Other Mode WMI Driver")
Cc: stable@vger.kernel.org
Link: https://sashiko.dev/#/patchset/20260331181208.421552-1-derekjohn.clark%40gmail.com [1]
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-3-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
lwmi_dev_evaluate_int() leaks output.pointer when retval == NULL (found
by sashiko.dev [1]).
Fix it by moving `ret_obj = output.pointer' outside of the `if (retval)'
block so that it is always freed by the __free cleanup callback.
No functional change intended.
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Fixes: e521d16e76 ("platform/x86: Add lenovo-wmi-helpers")
Cc: stable@vger.kernel.org
Link: https://sashiko.dev/#/patchset/20260331181208.421552-1-derekjohn.clark%40gmail.com [1]
Signed-off-by: Rong Zhang <i@rong.moe>
Signed-off-by: Derek J. Clark <derekjohn.clark@gmail.com>
Link: https://patch.msgid.link/20260510042546.436874-2-derekjohn.clark@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Fix spelling mistake in comment:
- occured -> occurred
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Md Shofiqul Islam <shofiqtest@gmail.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
The xfs logging macros include a newline, remove the \n, which adds an
extra one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Andrey Albershteyn <aalbersh@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Commit 4346ba1604 ("fprobe: Rewrite fprobe on function-graph tracer")
changed fprobe to register struct fprobe to an rcu-hlist, but it forgot
to wait for RCU GP. Thus there can be use-after-free if the fprobe is
released right after unregistering. This can be happened on fprobe
event and sample module code.
To fix this issue, add synchronize_rcu() in unregister_fprobe().
Note that BPF is OK because fprobe is used as a part of
bpf_kprobe_multi_link. This unregisters its fprobe in
bpf_kprobe_multi_link_release() and it is deallocated via
bpf_kprobe_multi_link_dealloc(), which is invoked from
bpf_link_defer_dealloc_rcu_gp() RCU callback.
For BPF, this also introduced unregister_fprobe_async() which does
NOT wait for RCU grace priod.
Link: https://lore.kernel.org/all/177813998919.256460.2809243930741138224.stgit@mhiramat.tok.corp.google.com/
Fixes: 4346ba1604 ("fprobe: Rewrite fprobe on function-graph tracer")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
A DIRECTORY entry's value field is used as the dir_offset for a
recursive call into __tb_property_parse_dir() with no depth counter.
A crafted peer that chains DIRECTORY entries into a back-reference
loop drives the parser until the kernel stack is exhausted and the
guard page fires. Any untrusted XDomain peer (cable, dock, in-line
inspector, adjacent host) that reaches the PROPERTIES_REQUEST
control-plane exchange can trigger this without authentication.
Thread a depth counter through tb_property_parse() and
__tb_property_parse_dir(), and reject blocks that exceed
TB_PROPERTY_MAX_DEPTH = 8. That is comfortably larger than any
observed legitimate XDomain layout.
Operators who do not need XDomain host-to-host discovery can disable
the path entirely with thunderbolt.xdomain=0 on the kernel command
line.
Fixes: cdae7c07e3 ("thunderbolt: Add support for XDomain properties")
Cc: stable@vger.kernel.org
Assisted-by: Claude:claude-opus-4-6
Assisted-by: Codex:gpt-5-4
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
