Add check_rx_hds test that verifies header/data split works across
payload sizes. The test sweeps payload sizes from 1 byte to 8KB, if any
data propagates up to userspace as SCM_DEVMEM_LINEAR, then the test
fails. This shows that regardless of payload size, ncdevmem's
configuration of hds-thresh to 0 is respected.
Add -L (--fail-on-linear) flag to ncdevmem that causes the receiver to
fail if any SCM_DEVMEM_LINEAR cmsg is received.
Use socat option for fixed block sizing and tcp nodelay to disable
nagle's algo to avoid buffering.
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-4-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
fbnic always advertises ETHTOOL_TCP_DATA_SPLIT_ENABLED via ethtool
.get_ringparam. To enable proper splitting for all flow types, even for
IP/Ethernet flows, this patch sets DMA_HINT_L4 unconditionally for all
RSS and NFC flow steering rules. According to the spec, L4 falls back to
L3 if no valid L4 is found, and L3 falls back to L2 if no L3 is found.
This makes sure that the correct header boundary is used regardless of
traffic type. This is important for zero-copy use cases where we must
ensure that all ZC packets are split correctly.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-3-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Increase FBNIC_HDR_BYTES_MIN from 128 to 256 bytes. The previous minimum
was too small to guarantee that very long L2+L3+L4 headers always fit
within the header buffer. When EN_HDR_SPLIT is disabled and a packet
exceeds MAX_HEADER_BYTES, splitting occurs at that byte offset instead
of the header boundary, resulting in some of the header landing in the
payload page. The increased minimum ensures headers always fit with the
MAX_HEADER_BYTES cut off and land in the header page.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-2-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix EN_HDR_SPLIT configuration by writing the field to RDE_CTL0 instead
of RDE_CTL1.
Because drop mode configuration and header splitting enablement both use
RDE_CTL0, we consolidate these configurations into the single function
fbnic_config_drop_mode.
Fixes: 2b30fc01a6 ("eth: fbnic: Add support for HDS configuration")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Acked-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Link: https://patch.msgid.link/20260211-fbnic-tcp-hds-fixes-v1-1-55d050e6f606@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The function devm_drm_dev_alloc() returns a pointer error upon failure
not NULL. Change null check to pointer error check.
Detected by Smatch:
drivers/gpu/drm/tiny/sharp-memory.c:549 sharp_memory_probe() error:
'smd' dereferencing possible ERR_PTR()
Fixes: b8f9f21716 ("drm/tiny: Add driver for Sharp Memory LCD")
Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patch.msgid.link/20260216040438.43702-1-ethantidmore06@gmail.com
Reset all counters, tasks and vruntime_head list on restart.
Signed-off-by: David Carlier <devnexen@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
fcg_read_stats() had a VLA allocating 21 * nr_cpus * 8 bytes on the
stack, risking stack overflow on large CPU counts (nr_cpus can be up
to 512).
Fix by using a single heap allocation with the correct size, reusing
it across all stat indices, and freeing it at the end.
Signed-off-by: David Carlier <devnexen@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stefano reports that after commit 62089b8048 ("kbuild: rpm-pkg:
Generate debuginfo package manually"), building with an rpm package
using rpm 4.20.0 fails with:
RPM build errors:
Dependency tokens must begin with alpha-numeric, '_' or '/': #�) = 0x0d000002
Dependency tokens must begin with alpha-numeric, '_' or '/': �) = 0x0d000000
Dependency tokens must begin with alpha-numeric, '_' or '/': ) = 0x7c0e000000
Unknown rich dependency op 'Hat': (Red Hat 15.2.1-7)) = 0x3130363230322000
Unknown rich dependency op 'Hat': (Red Hat 15.2.1-7)) = 0x4728203a43434800
Unknown rich dependency op 'Hat': (Red Hat 15.2.1-7)) = 0x3130363230322000
Unknown rich dependency op 'Hat': (Red Hat 15.2.1-7)) = 0x4728203a43434800
This error comes from the automatic requirements feature of rpm. The
-debuginfo subpackage has no dependencies, so disable this feature with
'AutoReq: 0' for this subpackage, avoiding the error. This matches the
official %_debug_template macro that rpm provides. While automatic
provides should be default enabled, be explicit like %_debug_template
does.
Additionally, while in the area, add the manual debug information
package to the Development/Debug group, further aligning with
%_debug_template.
Cc: stable@vger.kernel.org
Fixes: 62089b8048 ("kbuild: rpm-pkg: Generate debuginfo package manually")
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Closes: https://lore.kernel.org/CAGxU2F7FFNgb781_A7a1oL63n9Oy8wsyWceKhUpeZ6mLk=focw@mail.gmail.com/
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20260216-improve-manual-debuginfo-template-v1-1-e584b3f8d3be@kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
It's quite possible that opcodes that have payloads attached to them,
like IORING_OP_OPENAT/OPENAT2 or IORING_OP_SOCKET, that these paylods
can change over time. For example, on the openat/openat2 side, the
struct open_how argument is extensible, and could be extended in the
future to allow further arguments to be passed in.
Allow registration of a cBPF filter to give the size of the filter as
seen by userspace. If that filter is for an opcode that takes extra
payload data, allow it if the application payload expectation is the
same size than the kernels. If that is the case, the kernel supports
filtering on the payload that the application expects. If the size
differs, the behavior depends on the IO_URING_BPF_FILTER_SZ_STRICT flag:
1) If IO_URING_BPF_FILTER_SZ_STRICT is set and the size expectation
differs, fail the attempt to load the filter.
2) If IO_URING_BPF_FILTER_SZ_STRICT isn't set, allow the filter if
the userspace pdu size is smaller than what the kernel offers.
3) Regardless if IO_URING_BPF_FILTER_SZ_STRICT, fail loading the filter
if the userspace pdu size is bigger than what the kernel supports.
An attempt to load a filter due to sizing will error with -EMSGSIZE.
For that error, the registration struct will have filter->pdu_size
populated with the pdu size that the kernel uses.
Reported-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rather than open-code this logic in io_uring_populate_bpf_ctx() with
a switch, move it to the issue side definitions. Outside of making this
easier to extend in the future, it's also a prep patch for using the
pdu size for a given opcode filter elsewhere.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These WARN_ONs seem to trigger a lot, and we don't seem to have a
plan to fix them, so just drop them, as they are most likely
harmless.
Cc: stable@vger.kernel.org
Fixes: 176fdcbddf ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20241121014601.229391-1-airlied@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFPBAABCAA5FiEEe7vIQRWZI0iWSE3xu+CwddJFiJoFAmmTRqgbFIAAAAAABAAO
bWFudTIsMi41KzEuMTEsMiwyAAoJELvgsHXSRYiaUboIAIQRGZNZLzAD04PpEwDe
LP3g1iI6DytfzHkcqkf+cV1OHpsKZjKUDY8xw42L3ztktzD83W6ypSzQBz1opnUx
5w7N8EoE/GtY+pbOgBwGi7rvwg2i0+IkCdt9R8VpKa5fmwcgWcIpNtp0XRdWjWTb
pn04sRTHiNHlMZxdVHVAmlxgcC/8SNBHi4w5KJtDUrq+bkZUS3XAN2ssU3oKBpMy
OxhZw7BwfIO7PbBLFTrGQNPjfDU6IL7q8p7T6JcLyugPmqbvzAk07fDOs6GBFPBt
jc1wZvC8h32y7WnWqA4rU+g06jXb088B71IywpxzUSIyPs0rfGy/eEtdEOBWrqIT
5o8=
=dulw
-----END PGP SIGNATURE-----
Merge tag 'slab-for-7.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull more slab updates from Vlastimil Babka:
- Two stable fixes for kmalloc_nolock() usage from NMI context (Harry
Yoo)
- Allow kmalloc_nolock() allocations to be freed with kfree() and thus
also kfree_rcu() and simplify slabobj_ext handling - we no longer
need to track how it was allocated to use the matching freeing
function (Harry Yoo)
* tag 'slab-for-7.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm/slab: drop the OBJEXTS_NOSPIN_ALLOC flag from enum objext_flags
mm/slab: allow freeing kmalloc_nolock()'d objects using kfree[_rcu]()
mm/slab: use prandom if !allow_spin
mm/slab: do not access current->mems_allowed_seq if !allow_spin
By having them share the same space in struct io_cancel_data, it ends up
disallowing IORING_ASYNC_CANCEL_FD|IORING_ASYNC_CANCEL_USERDATA from
working. Eg you cannot match on both a file and user_data for
cancelation purposes. This obviously isn't a common use case as nobody
has reported this, but it does result in -ENOENT potentially being
returned when trying to match on both, rather than actually doing what
the API says it would.
Fixes: 4bf94615b8 ("io_uring: allow IORING_OP_ASYNC_CANCEL with 'fd' key")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Please consider pulling these changes from the signed vfs-7.0-rc1.misc.2 tag.
Thanks!
Christian
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCaZMOCwAKCRCRxhvAZXjc
oswrAP9r1zjzMimjX2J0hBoMnYjNzQfLLew8+IRygImQ+yaqWgD9Fiw/cQ9eE1Hm
TMLqck/ky588ywSDaBzfztrXAY3ISgg=
=4yr2
-----END PGP SIGNATURE-----
Merge tag 'vfs-7.0-rc1.misc.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull more misc vfs updates from Christian Brauner:
"Features:
- Optimize close_range() from O(range size) to O(active FDs) by using
find_next_bit() on the open_fds bitmap instead of linearly scanning
the entire requested range. This is a significant improvement for
large-range close operations on sparse file descriptor tables.
- Add FS_XFLAG_VERITY file attribute for fs-verity files, retrievable
via FS_IOC_FSGETXATTR and file_getattr(). The flag is read-only.
Add tracepoints for fs-verity enable and verify operations,
replacing the previously removed debug printk's.
- Prevent nfsd from exporting special kernel filesystems like pidfs
and nsfs. These filesystems have custom ->open() and ->permission()
export methods that are designed for open_by_handle_at(2) only and
are incompatible with nfsd. Update the exportfs documentation
accordingly.
Fixes:
- Fix KMSAN uninit-value in ovl_fill_real() where strcmp() was used
on a non-null-terminated decrypted directory entry name from
fscrypt. This triggered on encrypted lower layers when the
decrypted name buffer contained uninitialized tail data.
The fix also adds VFS-level name_is_dot(), name_is_dotdot(), and
name_is_dot_dotdot() helpers, replacing various open-coded "." and
".." checks across the tree.
- Fix read-only fsflags not being reset together with xflags in
vfs_fileattr_set(). Currently harmless since no read-only xflags
overlap with flags, but this would cause inconsistencies for any
future shared read-only flag
- Return -EREMOTE instead of -ESRCH from PIDFD_GET_INFO when the
target process is in a different pid namespace. This lets userspace
distinguish "process exited" from "process in another namespace",
matching glibc's pidfd_getpid() behavior
Cleanups:
- Use C-string literals in the Rust seq_file bindings, replacing the
kernel::c_str!() macro (available since Rust 1.77)
- Fix typo in d_walk_ret enum comment, add porting notes for the
readlink_copy() calling convention change"
* tag 'vfs-7.0-rc1.misc.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: add porting notes about readlink_copy()
pidfs: return -EREMOTE when PIDFD_GET_INFO is called on another ns
nfsd: do not allow exporting of special kernel filesystems
exportfs: clarify the documentation of open()/permission() expotrfs ops
fsverity: add tracepoints
fs: add FS_XFLAG_VERITY for fs-verity files
rust: seq_file: replace `kernel::c_str!` with C-Strings
fs: dcache: fix typo in enum d_walk_ret comment
ovl: use name_is_dot* helpers in readdir code
fs: add helpers name_is_dot{,dot,_dotdot}
ovl: Fix uninit-value in ovl_fill_real
fs: reset read-only fsflags together with xflags
fs/file: optimize close_range() complexity from O(N) to O(Sparse)
Please consider pulling these changes from the signed kernel-7.0-rc1.misc tag.
Thanks!
Christian
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCaZL+JwAKCRCRxhvAZXjc
ovU/AP4xgVxEegnNYrXZ+TpdCXbCtQZ54JqowFX73MBtaBHY1QD/YkDaIzl6K70v
d9P2Fe8Y6wOnIHxcjE4MIdMansphjAM=
=TN3q
-----END PGP SIGNATURE-----
Merge tag 'kernel-7.0-rc1.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull pidfs updates from Christian Brauner:
- pid: introduce task_ppid_vnr() helper
- pidfs: convert rb-tree to rhashtable
Mateusz reported performance penalties during task creation because
pidfs uses pidmap_lock to add elements into the rbtree. Switch to an
rhashtable to have separate fine-grained locking and to decouple from
pidmap_lock moving all heavy manipulations outside of it
Also move inode allocation outside of pidmap_lock. With this there's
nothing happening for pidfs under pidmap_lock
- pid: reorder fields in pid_namespace to reduce false sharing
- Revert "pid: make __task_pid_nr_ns(ns => NULL) safe for zombie
callers"
- ipc: Add SPDX license id to mqueue.c
* tag 'kernel-7.0-rc1.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
pid: introduce task_ppid_vnr() helper
pidfs: implement ino allocation without the pidmap lock
Revert "pid: make __task_pid_nr_ns(ns => NULL) safe for zombie callers"
pid: reorder fields in pid_namespace to reduce false sharing
pidfs: convert rb-tree to rhashtable
ipc: Add SPDX license id to mqueue.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmmTFjgACgkQ+iyteGJfRspirQCg1WlYh7sMQCS9zX2lXguYY1+9
qKsAn27lMglOgT/4pn8q215Z1YgVcNrW
=qZ12
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-6.20-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- iTCO: Drop vendor support
- s3c2410_wdt: Drop S3C2410 support
- Convert mpc8xxx-wdt to YAML
- Several small fixes and improvements
* tag 'linux-watchdog-6.20-rc1' of git://www.linux-watchdog.org/linux-watchdog:
dt-bindings: watchdog: qcom-wdt: Document Glymur watchdog
dt-bindings: watchdog: Convert mpc8xxx-wdt to YAML
dt-bindings: watchdog: samsung-wdt: Split if:then: and constrain more
dt-bindings: watchdog: samsung-wdt: Drop S3C2410
watchdog: s3c2410_wdt: Drop S3C2410 support
dt-bindings: watchdog: samsung-wdt: Define cluster constraints top-level
watchdog: rzv2h_wdt: Discard pm_runtime_put() return value
watchdog: rz: Discard pm_runtime_put() return values
watchdog: Make API functions const correct
watchdog: imx7ulp_wdt: handle the nowayout option
watchdog: sbsa: Update the W_IIDR Implementer bit mask to 0xFFF
watchdog: Always return time left until watchdog times out
watchdog: iTCO: Drop vendor support
watchdog: starfive-wdt: Fix PM reference leak in probe error path
fix it87_wdt early reboot by reporting running timer
- New Support & Features
* Add support for the TI LP5812 4x3 matrix RGB LED driver, including autonomous animation engine
control and extensive scan multiplexing modes.
* Add a new driver for the ams Osram AS3668 4-channel I2C LED controller.
* Extend the is31fl32xx driver to support the is31fl3293 variant, which features 3 channels and
12-bit PWM resolution.
- Improvements & Fixes
* Prevent the ExpressWire KTD2801 chip from entering an undefined state by disabling interrupts
during time-sensitive communication.
* Ensure the Qualcomm LPG driver detects hardware write failures by checking the return value of
regmap_bulk_write() during LUT programming.
* Fix kernel-doc warnings in the lm3692x driver by documenting missing struct members and
standardizing the comment style.
* Update the ExpressWire library to use fsleep() and unexport internal-only functions.
* Improve the is31fl32xx driver by reordering code to eliminate unnecessary forward declarations.
- Cleanups & Refactoring
* Simplify the LP55XX common LED driver by utilizing the for_each_available_child_of_node_scoped()
macro for more concise node iteration.
- Device Tree Bindings Updates
* Add new YAML bindings for the TI LP5860 and LP5812 LED controllers, and the ams Osram AS3668.
* Convert the TI LM3697 white LED driver binding to DT schema format.
* Allow multicolor LED nodes to be named with numeric suffixes (e.g., multi-led-0) to handle
multiple instances without unit addresses.
* Document support for the PMH0101 variant in the Qualcomm LPG PWM and SPMI Flash LED bindings.
* Add the issi,is31fl3293 compatible string to the is31fl32xx binding.
-----BEGIN PGP SIGNATURE-----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=IyMQ
-----END PGP SIGNATURE-----
Merge tag 'leds-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Support & Features:
- Add support for the TI LP5812 4x3 matrix RGB LED driver, including
autonomous animation engine control and extensive scan multiplexing
modes
- Add a new driver for the ams Osram AS3668 4-channel I2C LED
controller
- Extend the is31fl32xx driver to support the is31fl3293 variant,
which features 3 channels and 12-bit PWM resolution
Improvements & Fixes:
- Prevent the ExpressWire KTD2801 chip from entering an undefined
state by disabling interrupts during time-sensitive communication
- Ensure the Qualcomm LPG driver detects hardware write failures by
checking the return value of regmap_bulk_write() during LUT
programming
- Fix kernel-doc warnings in the lm3692x driver by documenting
missing struct members and standardizing the comment style
- Update the ExpressWire library to use fsleep() and unexport
internal-only functions
- Improve the is31fl32xx driver by reordering code to eliminate
unnecessary forward declarations
Cleanups & Refactoring:
- Simplify the LP55XX common LED driver by utilizing the
for_each_available_child_of_node_scoped() macro for more concise
node iteration
Device Tree Bindings Updates:
- Add new YAML bindings for the TI LP5860 and LP5812 LED controllers,
and the ams Osram AS3668
- Convert the TI LM3697 white LED driver binding to DT schema format
- Allow multicolor LED nodes to be named with numeric suffixes (e.g.,
multi-led-0) to handle multiple instances without unit addresses
- Document support for the PMH0101 variant in the Qualcomm LPG PWM
and SPMI Flash LED bindings
- Add the issi,is31fl3293 compatible string to the is31fl32xx
binding"
* tag 'leds-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds:
dt-bindings: leds: Convert ti,lm3697 to DT schema
leds: as3668: Driver for the ams Osram 4-channel i2c LED driver
dt-bindings: leds: Add new as3668 support
docs: leds: Document TI LP5812 LED driver
leds: Add basic support for TI/National Semiconductor LP5812 LED Driver
leds: qcom-lpg: Check the return value of regmap_bulk_write()
dt-bindings: leds: qcom,spmi-flash-led: Add PMH0101 compatible
dt-bindings: leds: leds-qcom-lpg: Add support for PMH0101 PWM
dt-bindings: leds: Allow differently named multicolor LEDs
leds: lp55xx: Simplify with scoped for each OF child loop
dt-bindings: leds: add TI/National Semiconductor LP5812 LED Driver
leds: is31f132xx: Add support for is31fl3293
leds: is31f132xx: Re-order code to remove forward declarations
dt-bindings: leds: Add issi,is31fl3293 to leds-is31fl32xx
leds: expresswire: Fix chip state breakage
dt-bindings: leds: Add LP5860 LED controller
leds: lm3692x: Fix kernel-doc for struct lm3692x_led
- New Support & Features
* Add a new driver for the Congatec Board Controller (CGBC) backlight, providing brightness
control via the board controller's PWM interface.
- Improvements & Fixes
* Resolve build failures in the Awinic AW99706 driver by switching to the correct GPIO consumer
header.
* Extend the Qualcomm WLED driver to support the specific over-voltage protection (OVP) values
required for the PMI8994 and PMI8950 variants.
- Device Tree Bindings Updates
* Document the device-specific over-voltage protection (OVP) millivolt ranges and default values
for Qualcomm PMI8994 and PMI8950 WLED controllers.
-----BEGIN PGP SIGNATURE-----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=Jf1S
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Support & Features:
- Add a new driver for the Congatec Board Controller (CGBC)
backlight, providing brightness control via the board controller's
PWM interface
Improvements & Fixes:
- Resolve build failures in the Awinic AW99706 driver by switching to
the correct GPIO consumer header
- Extend the Qualcomm WLED driver to support the specific
over-voltage protection (OVP) values required for the PMI8994 and
PMI8950 variants
Device Tree Bindings Updates:
- Document the device-specific over-voltage protection (OVP)
millivolt ranges and default values for Qualcomm PMI8994 and
PMI8950 WLED controllers"
* tag 'backlight-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: qcom-wled: Change PM8950 WLED configurations
dt-bindings: backlight: qcom-wled: Document ovp values for PMI8950
backlight: qcom-wled: Support ovp values for PMI8994
dt-bindings: backlight: qcom-wled: Document ovp values for PMI8994
backlight: aw99706: Fix build errors caused by wrong gpio header
backlight: Add Congatec Board Controller (CGBC) backlight support
- New Support & Features
* Add comprehensive support for the ROHM BD72720 PMIC, including core MFD, regulator, GPIO,
clock gate, RTC, and power-supply drivers.
* Add support for the Rockchip RK801 PMIC, including core MFD and regulator drivers.
* Add support for the ROHM BD73900 PMIC by leveraging existing common drivers.
* Wire up RTC, hwmon, and input sub-devices for the Apple SMC (macsmc) driver.
* Add support for the Delta Networks TN48M switch CPLD via the simple-mfd-i2c driver.
* Add support for the TS133 variant to the QNAP MCU driver.
* Provide support for the sama7d65 XLCD controller in the Atmel HLCDC driver.
* Add backlight sub-device support to the Congatec Board Controller (cgbc).
* Add Intel Nova Lake-S (NVL-S) PCI IDs to the Intel LPSS driver.
- Improvements & Fixes
* Implement a "wrapper regmap" for the ROHM BD72720 to handle dual I2C slave addresses (0x4b and
0x4c) transparently for child devices.
* Introduce mutex locking around 'mfd_of_node_list' in the MFD core to ensure safe concurrent
access.
* Fix a potential regulator resource leak in the Arizona core driver during boot sequence
failures.
* Resolve child device duplication issues on driver rebind for Qualcomm PM8xxx and OMAP USB host
drivers by using of_platform_depopulate().
* Fix IRQ domain name duplication for the Samsung S2MPG10 by adding a unique domain suffix.
* Implement LOCK register handling for the TI TPS65214 variant to unlock registers at probe
time.
* Fully convert the Loongson-2K BMC driver to use managed resources (pcim) and the standard PCI
resource API.
* Ensure the Apple SMC mutex is correctly initialized during probe to prevent NULL pointer
dereferences.
* Expand the ROHM BD71828 power-supply driver to support 9-bit register addresses.
* Simplify the Samsung S5M RTC driver by querying platform device IRQ resources directly.
* Revert an incorrect read-to-write mask change in the DA9052 SPI driver to restore default OTP
behavior.
* Fix kernel-doc warnings in the TI TPS6105x driver.
- Cleanups & Refactoring
* Simplify the MFD core by utilizing the scoped for_each_child_of_node_scoped() macro and
streamlining device_node storage.
* Rename ROHM BD71828 IC-specific entities to use consistent prefixes for better extensibility.
* Refactor ROHM BD71828 regmap definitions using the regmap_reg_range() macro.
* Update the ROHM BD71828 driver to use standard C-style comment headers.
* Remove the now unused 'irq_data' field from the Samsung SEC core structure.
* Drop unnecessary use of irqd_get_trigger_type() in the Maxim MAX77759 driver.
* Default MFD_SPACEMIT_P1 to 'm' if ARCH_SPACEMIT is selected.
* Add missing charger-related registers to the ROHM BD71828 core header and Type-C CC registers
to the AXP717.
- Device Tree Binding Updates
* Add new bindings for the ROHM BD72720 PMIC, Rockchip RK801 PMIC, Bitmain BM1880 System
Controller, and NXP LPC32xx System Control Block.
* Clarify trickle-charge terminology and add properties for voltage drop (VDR) correction and
upper charge limits to the generic battery binding.
* Document GPR syscon for NXP S32 SoCs and the smp-memram subnode for Aspeed SCU.
* Document numerous new Qualcomm SPMI PMIC compatibles (pmcx0102, pmh0101, pmk8850, etc.).
* Add compatibles for the sama7d65 XLCD (Atmel), LAN9691 Flexcom (Microchip), and various
MediaTek SCPSYS and regulator components.
* Fix a dead link to the audio codec binding in the DA9055 documentation.
-----BEGIN PGP SIGNATURE-----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=BxGL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Support & Features:
- Add comprehensive support for the ROHM BD72720 PMIC, including core
MFD, regulator, GPIO, clock gate, RTC, and power-supply drivers
- Add support for the Rockchip RK801 PMIC, including core MFD and
regulator drivers
- Add support for the ROHM BD73900 PMIC by leveraging existing common
drivers
- Wire up RTC, hwmon, and input sub-devices for the Apple SMC
(macsmc) driver
- Add support for the Delta Networks TN48M switch CPLD via the
simple-mfd-i2c driver
- Add support for the TS133 variant to the QNAP MCU driver
- Provide support for the sama7d65 XLCD controller in the Atmel HLCDC
driver
- Add backlight sub-device support to the Congatec Board Controller
(cgbc)
- Add Intel Nova Lake-S (NVL-S) PCI IDs to the Intel LPSS driver
Improvements & Fixes:
- Implement a "wrapper regmap" for the ROHM BD72720 to handle dual
I2C slave addresses (0x4b and 0x4c) transparently for child devices
- Introduce mutex locking around 'mfd_of_node_list' in the MFD core
to ensure safe concurrent access
- Fix a potential regulator resource leak in the Arizona core driver
during boot sequence failures
- Resolve child device duplication issues on driver rebind for
Qualcomm PM8xxx and OMAP USB host drivers by using
of_platform_depopulate()
- Fix IRQ domain name duplication for the Samsung S2MPG10 by adding a
unique domain suffix
- Implement LOCK register handling for the TI TPS65214 variant to
unlock registers at probe time
- Fully convert the Loongson-2K BMC driver to use managed resources
(pcim) and the standard PCI resource API
- Ensure the Apple SMC mutex is correctly initialized during probe to
prevent NULL pointer dereferences
- Expand the ROHM BD71828 power-supply driver to support 9-bit
register addresses
- Simplify the Samsung S5M RTC driver by querying platform device IRQ
resources directly
- Revert an incorrect read-to-write mask change in the DA9052 SPI
driver to restore default OTP behavior
- Fix kernel-doc warnings in the TI TPS6105x driver
- Cleanups & Refactoring
- Simplify the MFD core by utilizing the scoped
for_each_child_of_node_scoped() macro and streamlining device_node
storage
- Rename ROHM BD71828 IC-specific entities to use consistent prefixes
for better extensibility
- Refactor ROHM BD71828 regmap definitions using the
regmap_reg_range() macro
- Update the ROHM BD71828 driver to use standard C-style comment
headers
- Remove the now unused 'irq_data' field from the Samsung SEC core
structure
- Drop unnecessary use of irqd_get_trigger_type() in the Maxim
MAX77759 driver
- Default MFD_SPACEMIT_P1 to 'm' if ARCH_SPACEMIT is selected
- Add missing charger-related registers to the ROHM BD71828 core
header and Type-C CC registers to the AXP717
Device Tree Binding Updates:
- Add new bindings for the ROHM BD72720 PMIC, Rockchip RK801 PMIC,
Bitmain BM1880 System Controller, and NXP LPC32xx System Control
Block
- Clarify trickle-charge terminology and add properties for voltage
drop (VDR) correction and upper charge limits to the generic
battery binding
- Document GPR syscon for NXP S32 SoCs and the smp-memram subnode for
Aspeed SCU
- Document numerous new Qualcomm SPMI PMIC compatibles (pmcx0102,
pmh0101, pmk8850, etc)
- Add compatibles for the sama7d65 XLCD (Atmel), LAN9691 Flexcom
(Microchip), and various MediaTek SCPSYS and regulator components
- Fix a dead link to the audio codec binding in the DA9055
documentation"
* tag 'mfd-next-6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
dt-bindings: mfd: da9055: Fix dead link to codec binding
mfd: cgbc: Add support for backlight
dt-bindings: mfd: qcom,spmi-pmic: Document PMICs present on Glymur and Kaanapali
dt-bindings: mfd: Document smp-memram subnode for aspeed,ast2x00-scu
mfd: intel-lpss: Add Intel Nova Lake-S PCI IDs
mfd: ls2kbmc: Use PCI API instead of direct accesses
mfd: ls2kbmc: Fully convert to use managed resources
dt-bindings: mfd: mediatek: mt6397: Add missing MT6331 regulator compat
dt-bindings: mfd: mediatek,mt8195-scpsys: Add mediatek,mt6795-scpsys
dt-bindings: mfd: atmel,sama5d2-flexcom: Add microchip,lan9691-flexcom
mfd: omap-usb-host: Fix OF populate on driver rebind
mfd: qcom-pm8xxx: Fix OF populate on driver rebind
dt-bindings: mfd: syscon: Allow syscon compatible for mediatek,mt7981-topmisc
mfd: qnap-mcu: Add driver data for TS133 variant
dt-bindings: mfd: qnap,ts433-mcu: Add qnap,ts133-mcu compatible
mfd: sec: Fix IRQ domain names duplication
mfd: simple-mfd-i2c: Add Delta TN48M CPLD support
mfd: macsmc: Initialize mutex
dt-bindings: mfd: nxp: Add NXP LPC32xx System Control Block
mfd: Kconfig: Default MFD_SPACEMIT_P1 to 'm' if ARCH_SPACEMIT
...
Creating debugfs entries can trigger fs reclaim, which can enter back
into the block layer request_queue. This can cause deadlock if the
queue is frozen.
Previously, a WARN_ON_ONCE check was used in debugfs_create_files()
to detect this condition, but it was racy since the queue can be frozen
from another context at any time.
Introduce blk_debugfs_lock()/blk_debugfs_unlock() helpers that combine
the debugfs_mutex with memalloc_noio_save()/restore() to prevent fs
reclaim from triggering block I/O. Also add blk_debugfs_lock_nomemsave()
and blk_debugfs_unlock_nomemrestore() variants for callers that don't
need NOIO protection (e.g., debugfs removal or read-only operations).
Replace all raw debugfs_mutex lock/unlock pairs with these helpers,
using the _nomemsave/_nomemrestore variants where appropriate.
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Closes: https://lore.kernel.org/all/CAHj4cs9gNKEYAPagD9JADfO5UH+OiCr4P7OO2wjpfOYeM-RV=A@mail.gmail.com/
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Closes: https://lore.kernel.org/all/aYWQR7CtYdk3K39g@shinmob/
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yu Kuai <yukuai@fnnas.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Core changes:
- Drop the unused devm_pinctrl_unregister() function.
- Move pretended generic pin control functionality out of the
core and into the Amlogic AM4 driver. We have something better
coming (hopefully).
New hardware support:
- Spacemit K3 (RISC-V) pin control support.
- Atmel AT91 PIO4 (ARM32) SAMA7D65 pin control support.
- Exynos9610 (ARM64) pin control support.
- Qualcomm Mahua TLMM (ARM64) pin control support.
- Microchip Polarfire MSSIO (RISC-V) pin control support.
- Ocelot LAN9645XF (multiplatform) pin control support.
Improvements:
- Using a few more guards for locking.
- Various nonurgent fixes and tweaks.
-----BEGIN PGP SIGNATURE-----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=lmwJ
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- Drop the unused devm_pinctrl_unregister() function
- Move pretended generic pin control functionality out of the core
and into the Amlogic AM4 driver. We have something better coming
(hopefully)
New hardware support:
- Spacemit K3 (RISC-V) pin control support
- Atmel AT91 PIO4 (ARM32) SAMA7D65 pin control support
- Exynos9610 (ARM64) pin control support
- Qualcomm Mahua TLMM (ARM64) pin control support
- Microchip Polarfire MSSIO (RISC-V) pin control support
- Ocelot LAN9645XF (multiplatform) pin control support
Improvements:
- Using a few more guards for locking
- Various nonurgent fixes and tweaks"
* tag 'pinctrl-v7.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (73 commits)
pinctrl: generic: move function to amlogic-am4 driver
pinctrl: intel: Align Copyright note with corporate guidelines
pinctrl: mediatek: remove unused drv_offset field
pinctrl: canaan: k230: Fix NULL pointer dereference when parsing devicetree
pinctrl: single: fix refcount leak in pcs_add_gpio_func()
pinctrl: meson: amlogic-a4: Fix device node reference leak in bank helpers
pinctrl: qcom: sm8250-lpass-lpi: Fix i2s2_data_groups definition
pinctrl: core: Remove duplicate error messages
pinctrl: core: Simplify devm_pinctrl_*()
pinctrl: core: Remove unused devm_pinctrl_unregister()
dt-bindings: pinctrl: spacemit: fix drive-strength check warning
pinctrl: fix kismet issues with GENERIC_PINCTRL
pinctrl: tangier: Join tng_pinctrl_probe() into its wrapper
pinctrl: tangier: Remove duplicate error messages
pinctrl: lynxpoint: Remove duplicate error messages
pinctrl: cherryview: Remove duplicate error messages
pinctrl: baytrail: Remove duplicate error messages
pinctrl: intel: Remove duplicate error messages
pinctrl: equilibrium: Fix device node reference leak in pinbank_init()
dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
...
-----BEGIN PGP SIGNATURE-----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=ZT9I
-----END PGP SIGNATURE-----
Merge tag 'mips_7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (28 commits)
Revert "clk: microchip: core: allow driver to be compiled with COMPILE_TEST"
Revert "clk: microchip: fix typo in reference to a config option"
MIPS: Implement ARCH_HAS_CC_CAN_LINK
MIPS: rb532: Fix MMIO UART resource registration
MIPS: Work around LLVM bug when gp is used as global register variable
MIPS: Loongson64: env: Fixup serial clock-frequency when using LEFI
MIPS: Loongson2ef: Use pcibios_align_resource() to block io range
MIPS: Loongson2ef: Register PCI controller in early stage
clk: microchip: fix typo in reference to a config option
MIPS: Loongson64: dts: fix phy-related definition of LS7A GMAC
clk: microchip: core: allow driver to be compiled with COMPILE_TEST
MIPS: drop unused pic32.h header
watchdog: pic32-wdt: update include to use pic32.h from platform_data
watchdog: pic32-dmt: update include to use pic32.h from platform_data
serial: pic32_uart: update include to use pic32.h from platform_data
rtc: pic32: update include to use pic32.h from platform_data
pinctrl: pic32: update include to use pic32.h from platform_data
mmc: sdhci-pic32: update include to use pic32.h from platform_data
irqchip/irq-pic32-evic: update include to use pic32.h from platform_data
clk: microchip: core: update include to use pic32.h from platform_data
...
On the THUNDEROBOT ZERO laptop, the second NVMe slot and the discrete
NVIDIA GPU are both controlled by power-resource PXP. Due to the SSDT table
bug (lack of reference), PXP will be shut dow as an "unused" power resource
during initialization, making the NVMe slot #2 + NVIDIA both inaccessible.
This issue was introduced by commit a1224f34d7 ("ACPI: PM: Check
states of power resources during initialization"). Here are test
results on the three consecutive commits:
(bad again!) a1224f34d7 ACPI: PM: Check states of power resources during initialization
(good) bc28368596 ACPI: PM: Do not turn off power resources in unknown state
(bad) 519d81956e Linux 5.15-rc6
On commit bc28368596 ("ACPI: PM: Do not turn off power resources in
unknown state") this was not an issue because the power resource state
left UNKNOWN thus being ignored.
See also commit 9b04d99788 ("ACPI: PM: Do not turn of unused power
resources on the Toshiba Click Mini") which is another almost identical
case to this one.
Fixes: a1224f34d7 ("ACPI: PM: Check states of power resources during initialization")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=221087
Signed-off-by: Zhai Can <bczhc0@126.com>
Link: https://patch.msgid.link/20260214161452.2849346-1-bczhc0@126.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of struct blk_stat_callback documentation is already in kernel-doc
format. Convert the remaining struct members to kernel-doc to avoid
kernel-doc warnings:
Warning: block/blk-stat.h:62 struct member 'list' not described
in 'blk_stat_callback'
Warning: block/blk-stat.h:62 struct member 'timer_fn' not described
in 'blk_stat_callback'
Warning: block/blk-stat.h:62 struct member 'rcu' not described
in 'blk_stat_callback'
Warning: block/blk-stat.h:133 No description found for return value of
'blk_stat_is_active'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix all kernel-doc warnings in blk_types.h:
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_READ' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_WRITE' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_FLUSH' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_DISCARD' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_SECURE_ERASE' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_APPEND' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_WRITE_ZEROES' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_OPEN' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_CLOSE' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_FINISH' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_RESET' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_ZONE_RESET_ALL' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_DRV_IN' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_DRV_OUT' not described in enum 'req_op'
Warning: include/linux/blk_types.h:371 Enum value 'REQ_OP_LAST' not described in enum 'req_op'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 979dd8da76 ("regulator: s2mps11: add S2MPG11 regulator")
incorrectly ended up using macros for S2MPG10 in the S2MPG11 case. They
happen to end up giving the same result, but for clarity, the correct
macros should be used.
No functional change.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260210-s2mpg1x-regulators-fixes-v2-2-ab3d3457f1ae@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The sanity checks being removed in this commit are useless as earlier
code already checks for all conditions, including all error cases like
out-of-bounds conditions. In other words, the code being removed here
has no effect, as any potential error it could catch will already have
been caught by earlier code.
The checks removed here are also incomplete (as they're off-by-one) -
they should have been checking >= ARRAY_SIZE() to be complete.
Simply remove this redundant and incorrect code.
No functional change.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/aYmsu8qREppwBESH@stanley.mountain/
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260210-s2mpg1x-regulators-fixes-v2-1-ab3d3457f1ae@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the QUINARY_MI2S_RX which is used on some devices to
send audio data to speaker amplifiers.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://patch.msgid.link/20260211-snd-sm8250-quinary-mi2s-v1-1-f62e49d85af8@fairphone.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASUS Vivobook Pro 15X (M6501RR) with AMD Ryzen 9 6900HX has an
internal DMIC that is not detected without a DMI quirk entry, as the
BIOS does not set the AcpDmicConnected ACPI _DSD property.
Adding the DMI entry enables the ACP6x DMIC machine driver to probe
successfully.
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Salvini <guspatagonico@gmail.com>
Link: https://patch.msgid.link/20260210155156.29079-1-guspatagonico@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements delayed allocation (delalloc) in ntfs3 driver.
It introduces an in-memory delayed-runlist (run_da) and the helpers to
track, reserve and later convert those delayed reservations into real
clusters at writeback time. The change keeps on-disk formats untouched and
focuses on pagecache integration, correctness and safe interaction with
fallocate, truncate, and dio/iomap paths.
Key points:
- add run_da (delay-allocated run tree) and bookkeeping for delayed clusters.
- mark ranges as delalloc (DELALLOC_LCN) instead of immediately allocating.
Actual allocation performed later (writeback / attr_set_size_ex / explicit
flush paths).
- direct i/o / iomap paths updated to avoid dio collisions with
delalloc: dio falls back or forces allocation of delayed blocks before
proceeding.
- punch/collapse/truncate/fallocate check and cancel delay-alloc reservations.
Sparse/compressed files handled specially.
- free-space checks updated (ntfs_check_free_space) to account for reserved
delalloc clusters and MFT record budgeting.
- delayed allocations are committed on last writer (file release) and on
explicit allocation flush paths.
Tested-by: syzbot@syzkaller.appspotmail.com
Reported-by: syzbot+2bd8e813c7f767aa9bb1@syzkaller.appspotmail.com
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Deduplicate io_buffer_validate() calls by moving the checks into
io_sqe_buffer_register(). Now we also don't need special handling in
io_buffer_validate() passing through buffer removal requests. I also
was using it as a cleanup before some other changes.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
zc->len and zc->buf are not actually used once you get to the retry
stage. The buffer remains in kmsg->msg.msg_iter, which is setup in
io_send_setup.
Note: it still seems needed in io_send due to io_send_select_buffer
needing it (for the len parameter).
Signed-off-by: Dylan Yudaken <dyudaken@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Attempting SOCKET_URING_OP_SETSOCKOPT on an AF_NETLINK socket resulted
in an -EOPNOTSUPP, as AF_NETLINK doesn't have an ioctl in its struct
proto, but only in struct proto_ops.
Prior to the blamed commit, io_uring_cmd_sock() only had two cmd_op
operations, both requiring ioctl, thus the check was warranted.
Since then, 4 new cmd_op operations have been added, none of which
depend on ioctl. This patch moves the ioctl check, so it only applies
to the original operations.
AFAICT, the ioctl requirement was unintentional, and it wasn't
visible in the blamed patch within 3 lines of context.
Cc: stable@vger.kernel.org
Fixes: a5d2f99aff ("io_uring/cmd: Introduce SOCKET_URING_OP_GETSOCKOPT")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Gabriel Krisman Bertazi <krisman@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- kprobes: Use a dedicated kernel thread to optimize the kprobes
instead of using workqueue thread. Since the kprobe optimizer waits
a long time for synchronize_rcu_task(), it can block other workers
in the same queue if it uses a workqueue.
- kprobe-events: Returns immediately if no new probe events are
specified on the kernel command line at boot time. This shorten the
kernel boot time.
- kprobes: When a kprobe is fully removed from the kernel code,
retry optimizing another kprobe which is blocked by that kprobe.
-----BEGIN PGP SIGNATURE-----
iQFPBAABCgA5FiEEh7BulGwFlgAOi5DV2/sHvwUrPxsFAmmPtX4bHG1hc2FtaS5o
aXJhbWF0c3VAZ21haWwuY29tAAoJENv7B78FKz8bgoUH/0oZ9/c+wkn9AKxFlOAw
AIbtTfKiQHXPirhamYuEbJJWTUH2O/Wr0SQrIkbwJzToou5CRTuT5UQBpmOk2GKZ
uZ5bO63nOMn/1ECbDpc+lFGV5J4Dn5Pw2GFjUTR6EPwms+CN/d6f2LlvuAVfJX7Y
klL2X9/QLwV5QT8La5zNEka2zBfrZlZ9a5DGoLtgdwX2zosuef9aDnisS2jkLenH
wugZLryx0Qvlj9DXimP7oVZpYDHr0hZEI3CNQPge0gMQDj1XajGawYfkhrfaeFMX
4eXjFCN+NQG6fBUpDugcOThOypWmjlJhoYxxROJu0eFcLQjsuWjp6jLixI9Nr7P+
tQk=
=syAj
-----END PGP SIGNATURE-----
Merge tag 'probes-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull kprobes updates from Masami Hiramatsu:
- Use a dedicated kernel thread to optimize the kprobes instead of
using workqueue thread. Since the kprobe optimizer waits a long time
for synchronize_rcu_task(), it can block other workers in the same
queue if it uses a workqueue.
- kprobe-events: return immediately if no new probe events are
specified on the kernel command line at boot time. This shortens
the kernel boot time.
- When a kprobe is fully removed from the kernel code, retry optimizing
another kprobe which is blocked by that kprobe.
* tag 'probes-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
kprobes: Use dedicated kthread for kprobe optimizer
tracing: kprobe-event: Return directly when trace kprobes is empty
kprobes: retry blocked optprobe in do_free_cleaned_kprobes
Some XRUN-related error messages may repeat themselves, because there
can be multiple pending packets. Modify notify_xrun() function to
return whether it's being stopped or not, and show the error message
only once when the XRUN is actually handled.
Along with it, fix a typo of word package to packet in the error
message.
Link: https://patch.msgid.link/20260216141209.1849200-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At silencing the playback URB packets in the implicit fb mode before
the actual playback, we blindly assume that the received packets fit
with the buffer size. But when the setup in the capture stream
differs from the playback stream (e.g. due to the USB core limitation
of max packet size), such an inconsistency may lead to OOB writes to
the buffer, resulting in a crash.
For addressing it, add a sanity check of the transfer buffer size at
prepare_silent_urb(), and stop the data copy if the received data
overflows. Also, report back the transfer error properly from there,
too.
Note that this doesn't fix the root cause of the playback error
itself, but this merely covers the kernel Oops.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221076
Link: https://patch.msgid.link/20260216141209.1849200-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We did manual copies over loop for the packet data update of the
implicit feedback, but this can be optimized with a simple memcpy().
Along with it, change the data type of snd_usb_packet_info struct to
align with other (from uint32_t to int).
No functional changes but only code optimizations.
Link: https://patch.msgid.link/20260216141209.1849200-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At receiving the packets from the implicit feedback source, we didn't
update ctx->packets field but only the ctx->packet_size[] data.
In exceptional cases, this might lead to unexpectedly superfluous data
transfer (although this won't happen usually due to the nature of USB
isochronous transfer). Fix it to update the field properly.
Link: https://patch.msgid.link/20260216141209.1849200-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the intermediate state gone, no longer useful. Just check against
NULL where needed.
After looking carefully, the check for allocated in xe_fb_pin.c is
unneeded. vma->node is never NULL. The check is specifically only
to check if vma->node == the bo's root tile ggtt_obj.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260206112108.1453809-12-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
This extra step is easier to handle inside xe_ggtt.c and makes
xe_ggtt_node_allocated a simple null check instead, as the intermediate
state 'allocated but not inserted' is no longer used.
Privatize xe_ggtt_node_fini() and init() as they're no longer used
outside of xe_ggtt.c
Reviewed-by: Matthew Brost <matthew.brost@intel.com> #v1
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260206112108.1453809-11-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
No users left outside of xe_ggtt.c, so we can make the struct private.
This prevents us from accidentally touching it before init.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260206112108.1453809-10-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The previous code was using a complicated system with 2 balloons to
set GGTT size and adjust GGTT offset. While it works, it's overly
complicated.
A better approach is to set the offset and size when initializing GGTT,
this removes the need for adding balloons. The resize function only
needs readjust ggtt->start to have GGTT at the new offset.
This removes the need to manipulate the internals of xe_ggtt outside
of xe_ggtt, and cleans up a lot of now unneeded code.
Co-developed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260206112108.1453809-9-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Fix all functions that use node->start to use xe_ggtt_node_addr,
and add ggtt->start to node->start.
This will make node shifting for SR-IOV VF a one-liner, instead of
manually changing each GGTT node's base address.
Also convert some uses of mutex_lock/unlock to mutex guards.
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260206112108.1453809-8-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
system_wq should be the per-cpu workqueue, yet in this name nothing makes
that clear, so replace system_wq with system_percpu_wq.
The old wq (system_wq) will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://patch.msgid.link/20251105101134.82064-1-marco.crivellari@suse.com
Signed-off-by: Maíra Canal <mcanal@igalia.com>
In linehandle_create(), there is a statement like this:
retain_and_null_ptr(lh);
Soon after, there is a debug printout that dereferences "lh", which
will crash things.
Avoid the crash by using handlereq.lines, which is the same value.
Fixes: da7e394bf5 ("gpio: convert linehandle_create() to FD_PREPARE()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20260215120555.v2.1.I77c3eb563271c21870379eefd16ebbc4e09635bb@changeid
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
The function gpio_device_get_desc() can return an error pointer and is
not checked for one. Add check for error pointer.
Fixes: ddeb66d2cb ("gpio: nomadik: don't print out global GPIO numbers in debugfs callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Tidmore <ethantidmore06@gmail.com>
Link: https://patch.msgid.link/20260214044531.43539-1-ethantidmore06@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
. defconfig cleanup
. fix for legacy 68000 CPU memmove() of non-aligned pointers
. replace strcpy() with strscpy() for ucsimm target
-----BEGIN PGP SIGNATURE-----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=r0QB
-----END PGP SIGNATURE-----
Merge tag 'm68knommu-for-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
- defconfig cleanup
- fix for legacy 68000 CPU memmove() of non-aligned pointers
- replace strcpy() with strscpy() for ucsimm target
* tag 'm68knommu-for-v7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Replace deprecated strcpy with strscpy in init_ucsimm
m68k: nommu: fix memmove() with differently aligned src and dest for 68000
m68k: defconfig: Clean up references to non-existing configs
Currently, when smb signature verification fails, the behaviour is to log
the failure without any action to terminate the session.
Call cifs_reconnect() when client required signature verification fails.
Otherwise, log the error without reconnecting.
Signed-off-by: Aaditya Kansal <aadityakansal390@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In several places in the code, we have a label to signify
the start of the code where a request can be replayed if
necessary. However, some of these places were missing the
necessary reinitializations of certain local variables
before replay.
This change makes sure that these variables get initialized
after the label.
Cc: stable@vger.kernel.org
Reported-by: Yuchan Nam <entropy1110@gmail.com>
Tested-by: Yuchan Nam <entropy1110@gmail.com>
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
