Add support for the SPMI controller found in the MT8196 SoC:
this supports SPMI 2.0 and features two SPMI buses.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://patch.msgid.link/20260123182039.224314-6-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the per-bus RCS interrupt by adding a new linear
irqdomain and its irqchip.
The SPMI controller will raise an interrupt when any of the SPMI
connected devices' irq needs attention (whenever any interrupt
fires on any SID) in one of four registers, where each register
holds four sets of four bits of information about a SID interrupt.
This controller's RCS interrupt status knowledge is limited to the
address of the SID that raised an interrupt, but does not have any
details about the devices irq numbers: as this may change with a
future SPMI controller IP version, the devicetree is meant to hold
three cells, where the first one is the SPMI SID interrupt number,
the second one is a device interrupt number, and the third one is
the irq sense type.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://patch.msgid.link/20260123182039.224314-5-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the spin unlocking to after reading the contents of the
PMIF_SWINF_(x)_RDATA_31_0 register in pmif_spmi_read_cmd():
since this is the only register that we can read to get the
data from all of the arbitered busses, a concurrent request
for reading (especially on a busy arbiter) will show a race
condition and a unexpected or corrupted value may be read.
Doing the entire read sequence while spin locked guarantees
that concurrent access to the arbiter doesn't happen.
Fixes: f200fff8d0 ("spmi: mtk-pmif: Serialize PMIF status check and command submission")
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes: b45b3ccef8 ("spmi: mediatek: Add support for MT6873/8192")
Link: https://patch.msgid.link/20260123182039.224314-4-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding support for MT8196/MT6991 SoCs having
multiple SPMI busses, move the bus specific parameters into a new
pmif_bus structure and keep the SoC-specific data in the already
existing struct pmif, and add means to register multiple SPMI
controllers.
While this needs a different devicetree node structure, where each
of the controllers are in subnodes of a main SPMI node, and where
each has its own resources (iospaces and clocks), support for the
legacy single-controller was retained and doesn't require any DT
change in the currently supported SoCs.
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://patch.msgid.link/20260123182039.224314-3-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the MT8196 SPMI 2.0 Controller with a new schema.
This is a MIPI SPMI 2.0 compliant IP, composed of a main arbiter
and two SPMI master controllers with Request Capable Slave (RCS)
support.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://patch.msgid.link/20260123182039.224314-2-sboyd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start a new Japanese translation of
Documentation/process/submitting-patches.rst.
Instead of moving the outdated 2011
translation (SubmittingPatches), we are starting a fresh translation of
the current English document.
This patch adds the initial file structure, the warning about the
document being under construction, and the translation of the
introduction section.
The translation work will be done incrementally.
Suggested-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/298d3a9c-41c1-4cbd-b4ab-d3009df9388c@gmail.com/
Signed-off-by: Akiyoshi Kurita <weibu@redadmin.org>
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Message-ID: <20260120154543.2063635-1-weibu@redadmin.org>
One new device ID, plus a few fixes. The most substantial of the fixes
is for the Cadence driver which in at least some instantiations requires
transmit data to drive data through the IP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmlzk5EACgkQJNaLcl1U
h9Do6ggAhqhHRYoU2DyG+fDxCGBM7N1qj02/YsG8XETHsr2p+bIoB7VzVNF1xE/w
hTeHsWsEpj7rAt2Ieq31n1on3iS75lkY7f29uyoJa8uorBCSd+MpVNoeySZVr/s6
nFFhMiIjf/g82UdNoaaDBCvcCYphg+FNhkswSJ/Z1Hej4kw74LZydSUggpsmLR+K
wnZUpV2PRGH1fMnJgRHDR0JV9PfMAe6BW043ud1cQDLpd2GQXKOLbwDDWv69XZBL
F1O8ulHsTRb8hDKxZ2bBXNaLW4+eZp3AglVEIPHtrztLmIyyyToYIXFGALr1DV0C
nXuDf/zi9Dlfuk1UvAcEa81qhv2Vfg==
=PFwm
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"One new device ID, plus a few fixes.
The most substantial of the fixes is for the Cadence driver which in
at least some instantiations requires transmit data to drive data
through the IP"
* tag 'spi-fix-v6.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: intel-pci: Add support for Nova Lake SPI serial flash
spi: spi-cadence: enable SPI_CONTROLLER_MUST_TX
spi: hisi-kunpeng: Fixed the wrong debugfs node name in hisi_spi debugfs initialization
spi: spi-sprd-adi: Fix double free in probe error path
Moving tcp_stream_memory_free() to tcp.c allows the compiler
to (auto)inline it from tcp_poll() and tcp_sendmsg_locked()
for better performance.
$ scripts/bloat-o-meter -t vmlinux.old vmlinux.new
add/remove: 0/0 grow/shrink: 2/0 up/down: 118/0 (118)
Function old new delta
tcp_poll 840 923 +83
tcp_sendmsg_locked 4217 4252 +35
Total: Before=22573095, After=22573213, chg +0.00%
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Link: https://patch.msgid.link/20260122090228.1678207-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit d8f87aa5fa ("net: remove HIPPI support and RoadRunner HIPPI
driver") removes the hippidevice header file, but misses that there is
still a file entry in MAINTAINERS referring to it.
Remove the obsolete file entry in NETWORKING DRIVERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260122074609.151058-1-lukas.bulwahn@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A couple of small fixes, one error handling one and another for misuse
of the hwspinlock API.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmlzkXAACgkQJNaLcl1U
h9BzEgf+P1U0W8t1Ol/v6sttRiZOaIAlM0/3ZX0zsttJarHTjdMY7ilzFvN361wR
xNsVNB8FUVrAeVzoW4+xPNgPEuBqD+pO9kUz4cg2ZEt2Ym/BsgeL6vE7Gbj5+P6V
6tIZOZkIQnQZ4DqCXH3IMv5AFCgHWtrt/3bHVUpUUHdxYadvh1iKRwv1Sgr/SWeO
wi1zlYGABY+Bv8FDzv6w29CCKI5YkMahuLSzXEYlaneGF8eCswyogzyaHG6gmD6h
t06OlG2+vNlghrvJqbXk+casJyM7UDxF8NUgWrFQ3k+kBDAQojcrqAfFPiGMgmyV
SVfFVQ0OGsaLh1KQHJi9KivlQyjT0Q==
=nXyd
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v6.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of small fixes, one error handling one and another for misuse
of the hwspinlock API"
* tag 'regmap-fix-v6.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix race condition in hwspinlock irqsave routine
regmap: maple: free entry on mas_store_gfp() failure
Convert all imports in the devres to use "kernel vertical" style.
Cc: Gary Guo <gary@garyguo.net>
Cc: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Gary Guo <gary@garyguo.net>
Signed-off-by: Zhi Wang <zhiw@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Link: https://patch.msgid.link/20260121202212.4438-2-zhiw@nvidia.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
- fix resource leaks in error paths in GPIO character device code
- return -ENOMEM and not -ENODEV on memory allocation failure
- fix an audio issue on Qualcomm platforms due to configuration not
being propagated to pinctrl from shared GPIO proxy
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEkeUTLeW1Rh17omX8BZ0uy/82hMMFAmlzQPgACgkQBZ0uy/82
hMOVLBAAoRiX+SyZ2zXnsjqmgoUB4DdpeRLu7E4vgrB3mvSqdKfFLG76aPUO0S9H
QwYG5S8P/NoXNt7wJKoIc0jBiv+/P7leGIe7rEumg+uzfQ7dznIdXloPNttE9mB2
eaLQF3B1i/HtHKOSwJYtq5E8Pqxy0TU56SYMTbfJV7+ZpqhSv7z43lxSCIjXFPJ4
rhmn07rs1t6q/QGusdHyEk35kzYOGYhFkLdWuUnqVAw5/y2PDXU00YQ/r/av5CO4
K38WqDOpxl1/HCifQUYof89nUq5aysAHu80pUd3u7GsPZPaL9KZY8xuRdYIIlC8e
3Mr2KhgeKWrx8IrFizOoE4TnsXkLzD61JOQmHMnx9kXIRU1GcUdO9NS1CAxZABJ9
lO4mTa+QnYI4PDlsx0e0ixgShzu/HhhJhdLBmbRhUEsJNp1qlhisyNIBhkHxByJ7
bGXWxUOARccceSX8EkhcC0B1W24sTwH+1pjotzZRoCt0e1vD4cNU67nnIP23ApdC
j+ExPdj89pe9Hc7NlxkGNx7Z2eG9l8J3Tx2EkK4TIGnUplEqrZl3sXG9KEYxesFd
1dNPcv9C1qrVhquEGQHOYNfCH5nljvFq7cjE0H+TWXVvLVAgRhLpgVnxXSiFkjry
mC2VwVUcmvYti0T6vhvYb213XI/zMm0+7sOyRmjXrpG8nvQl7kk=
=/U+a
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Some fixes to resource leaks in the character device handling and
another small fix for shared GPIO management:
- fix resource leaks in error paths in GPIO character device code
- return -ENOMEM and not -ENODEV on memory allocation failure
- fix an audio issue on Qualcomm platforms due to configuration not
being propagated to pinctrl from shared GPIO proxy"
* tag 'gpio-fixes-for-v6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: shared: propagate configuration to pinctrl
gpio: cdev: Fix resource leaks on errors in gpiolib_cdev_register()
gpio: cdev: Fix resource leaks on errors in lineinfo_changed_notify()
gpio: cdev: Correct return code on memory allocation failure
The TAS fallback can be invoked directly when queued spin locks are
disabled, and through the slow path when paravirt is enabled for queued
spin locks. In the latter case, the res_spin_lock macro will attempt the
fast path and already hold the entry when entering the slow path. This
will lead to creation of extraneous entries that are not released, which
may cause false positives for deadlock detection.
Fix this by always preceding invocation of the TAS fallback in every
case with the grabbing of the held lock entry, and add a comment to make
note of this.
Fixes: c9102a68c0 ("rqspinlock: Add a test-and-set fallback")
Reported-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Tested-by: Amery Hung <ameryhung@gmail.com>
Link: https://lore.kernel.org/r/20260122115911.3668985-1-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Define and advertise AVX10_VNNI_INT CPUID to userspace when it's supported
by the host.
AVX10_VNNI_INT (0x24.0x1.ECX[bit 2]) is a discrete feature bit
introduced on Intel Diamond Rapids, which enumerates the support for
EVEX VPDP* instructions for INT8/INT16 [*].
Since this feature has no actual kernel usages, define it as a KVM-only
feature in reverse_cpuid.h.
Advertise new CPUID subleaf 0x24.0x1 with AVX10_VNNI_INT bit to
userspace for guest use. It's safe since no additional enabling work
is needed in the host kernel.
[*]: Intel Advanced Vector Extensions 10.2 Architecture Specification
(rev 5.0).
Tested-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://patch.msgid.link/20251120050720.931449-5-zhao1.liu@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Bump up the maximum supported AVX10 version and enumerate AVX10.2 to
userspace when it's supported by the host.
Intel AVX10 Version 2 (Intel AVX10.2) includes a suite of new
instructions delivering new AI features and performance, accelerated
media processing, expanded Web Assembly, and Cryptography support, along
with enhancements to existing legacy instructions for completeness and
efficiency, and it is enumerated as version 2 in CPUID 0x24.0x0.EBX[bits
0-7] [1].
AVX10.2 has no current kernel usage and requires no additional host
kernel enabling work (based on AVX10.1 support) and provides no new
VMX controls [2]. Moreover, since AVX10.2 is the superset of AVX10.1,
there's no need to worry about AVX10.1 and AVX10.2 compatibility issues
in KVM.
Therefore, it's safe to advertise AVX10.2 version to userspace directly
if host supports AVX10.2.
[1]: Intel Advanced Vector Extensions 10.2 Architecture Specification
(rev 5.0).
[2]: Note: Since AVX10.2 spec (rev 4.0), it has been declared "AVX10/512
will be used in all Intel products, supporting vector lengths of
128, 256, and 512 in all product lines", and the VMX support (in
earlier revisions) for AVX10/256 guest on AVX10/512 host has been
dropped.
Tested-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://patch.msgid.link/20251120050720.931449-4-zhao1.liu@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Define and advertise AMX CPUIDs (0x1E.0x1) to userspace when the leaf is
supported by the host.
Intel Diamond Rapids adds new AMX instructions to support new formats
and memory operations [*], and introduces the CPUID subleaf 0x1E.0x1
to centralize the discrete AMX feature bits within EAX.
Since these AMX features have no actual kernel usages, define them as
KVM-only features in reverse_cpuid.h.
In addition to the new features, CPUID 0x1E.0x1.EAX[bits 0-3] are
aliaseed positions of existing AMX feature bits distributed across the
0x7 leaves. To avoid duplicate feature names, name these aliases with an
*_ALIAS suffix, and define them in reverse_cpuid.h as KVM-only features
as well.
Advertise new CPUID subleaf 0x1E.0x1 with its AMX CPUID feature bits to
userspace for guest use. It's safe since no additional enabling work
is needed in the host kernel.
[*]: Intel Architecture Instruction Set Extensions and Future Features
(rev.059).
Tested-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://patch.msgid.link/20251120050720.931449-3-zhao1.liu@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Define the feature flag for MOVRS and advertise support to userspace when
the feature is supported by the host.
MOVRS is a new set of instructions introduced in the Intel platform
Diamond Rapids, to provide load instructions that carry a read-shared
hint.
Functionally, MOVRS family is equivalent to existing load instructions,
but its read-shared hint indicates that the source memory location is
likely to become read-shared by multiple processors, i.e., read in the
future by at least one other processor before it is written (assuming it
is ever written in the future). This hint could optimize the behavior of
the caches, especially shared caches, for this data for future reads by
multiple processors. Additionally, MOVRS family also includes a software
prefetch instruction, PREFETCHRST2, that carries the same read-shared
hint. [*]
MOVRS family is enumerated by CPUID single-bit (0x7.0x1.EAX[bit 31]).
Since it's on a densely-populated CPUID leaf and some other bits on
this leaf have kernel usages, define this new feature in cpufeatures.h,
but hide it in /proc/cpuinfo due to lack of current kernel usage.
Advertise MOVRS bit to userspace directly. It's safe, since there's no
new VMX controls or additional host enabling required for guests to use
this feature.
[*]: Intel Architecture Instruction Set Extensions and Future Features
(rev.059).
Tested-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://patch.msgid.link/20251120050720.931449-2-zhao1.liu@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
A collection of a few more small fixes for HD- and USB-audio,
including a regression fix for the OOB fix that was included in
the previous PR.
-----BEGIN PGP SIGNATURE-----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=MH0R
-----END PGP SIGNATURE-----
Merge tag 'sound-6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of a few more small fixes for HD- and USB-audio,
including a regression fix for the OOB fix that was included
in the previous pull request"
* tag 'sound-6.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: ALC269 fixup for Lenovo Yoga Book 9i 13IRU8 audio
ALSA: hda/realtek: Add quirk for Samsung 730QED to fix headphone
ALSA: usb-audio: Use the right limit for PCM OOB check
ALSA: usb-audio: Fix use-after-free in snd_usb_mixer_free()
ALSA: hda/realtek: Fix headset mic for TongFang X6AR55xU
ALSA: ctxfi: Fix potential OOB access in audio mixer handling
selftests: ALSA: Remove unused variable in utimer-test
ALSA: usb-audio: Add delay quirk for MOONDROP Moonriver2 Ti
ALSA: scarlett2: Fix buffer overflow in config retrieval
ALSA: usb: Increase volume range that triggers a warning
The xchk_xfile_*_descr macros call kasprintf, which can fail to allocate
memory if the formatted string is larger than 16 bytes (or whatever the
nofail guarantees are nowadays). Some of them could easily exceed that,
and Jiaming Zhang found a few places where that can happen with syzbot.
The descriptions are debugging aids and aren't required to be unique, so
let's just pass in static strings and eliminate this path to failure.
Note this patch touches a number of commits, most of which were merged
between 6.6 and 6.14.
Cc: r772577952@gmail.com
Cc: <stable@vger.kernel.org> # v6.12
Fixes: ab97f4b1c0 ("xfs: repair AGI unlinked inode bucket lists")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Jiaming Zhang <r772577952@gmail.com>
If we're trying to replace an xattr in a shortform attr structure and
the old entry fits the new entry, we can just memcpy and exit without
having to delete, compact, and re-add the entry (or worse use the attr
intent machinery). For parent pointers this only advantages renaming
where the filename length stays the same (e.g. mv autoexec.bat
scandisk.exe) but for regular xattrs it might be useful for updating
security labels and the like.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
After a recent fsmark benchmarking run, I observed that the overhead of
parent pointers on file creation and deletion can be a bit high. On a
machine with 20 CPUs, 128G of memory, and an NVME SSD capable of pushing
750000iops, I see the following results:
$ mkfs.xfs -f -l logdev=/dev/nvme1n1,size=1g /dev/nvme0n1 -n parent=0
meta-data=/dev/nvme0n1 isize=512 agcount=40, agsize=9767586 blks
= sectsz=4096 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=1, rmapbt=1
= reflink=1 bigtime=1 inobtcount=1 nrext64=1
= exchange=0 metadir=0
data = bsize=4096 blocks=390703440, imaxpct=5
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1, parent=0
log =/dev/nvme1n1 bsize=4096 blocks=262144, version=2
= sectsz=4096 sunit=1 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
= rgcount=0 rgsize=0 extents
= zoned=0 start=0 reserved=0
So we created 40 AGs, one per CPU. Now we create 40 directories and run
fsmark:
$ time fs_mark -D 10000 -S 0 -n 100000 -s 0 -L 8 -d ...
# Version 3.3, 40 thread(s) starting at Wed Dec 10 14:22:07 2025
# Sync method: NO SYNC: Test does not issue sync() or fsync() calls.
# Directories: Time based hash between directories across 10000 subdirectories with 180 seconds per subdirectory.
# File names: 40 bytes long, (16 initial bytes of time stamp with 24 random bytes at end of name)
# Files info: size 0 bytes, written with an IO size of 16384 bytes per write
# App overhead is time in microseconds spent in the test not doing file writing related system calls.
parent=0 parent=1
================== ==================
real 0m57.573s real 1m2.934s
user 3m53.578s user 3m53.508s
sys 19m44.440s sys 25m14.810s
$ time rm -rf ...
parent=0 parent=1
================== ==================
real 0m59.649s real 1m12.505s
user 0m41.196s user 0m47.489s
sys 13m9.566s sys 20m33.844s
Parent pointers increase the system time by 28% overhead to create 32
million files that are totally empty. Removing them incurs a system
time increase of 56%. Wall time increases by 9% and 22%.
For most filesystems, each file tends to have a single owner and not
that many xattrs. If the xattr structure is shortform, then all xattr
changes are logged with the inode and do not require the the xattr
intent mechanism to persist the parent pointer.
Therefore, we can speed up parent pointer operations by calling the
shortform xattr functions directly if the child's xattr is in short
format. Now the overhead looks like:
$ time fs_mark -D 10000 -S 0 -n 100000 -s 0 -L 8 -d ...
parent=0 parent=1
================== ==================
real 0m58.030s real 1m0.983s
user 3m54.141s user 3m53.758s
sys 19m57.003s sys 21m30.605s
$ time rm -rf ...
parent=0 parent=1
================== ==================
real 0m58.911s real 1m4.420s
user 0m41.329s user 0m45.169s
sys 13m27.857s sys 15m58.564s
Now parent pointers only increase the system time by 8% for creation and
19% for deletion. Wall time increases by 5% and 9% now.
Close the performance gap by creating helpers for the attr set, remove,
and replace operations that will try to make direct shortform updates,
and fall back to the attr intent machinery if that doesn't work. This
works for regular xattrs and for parent pointers.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The dp parameter to this function is an alias of args->dp, so remove it
for clarity before we go adding new callers.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In debugging other problems with generic/753, it turns out that it's
possible for the system go to down in the middle of a remote xattr set
operation such that the leaf block entry is marked incomplete and
valueblk is set to zero. Make this no longer a failure.
Cc: <stable@vger.kernel.org> # v4.15
Fixes: 13791d3b83 ("xfs: scrub extended attribute leaf space")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
In the previous patches, we observed that it's possible for there to be
freemap entries with zero size but a nonzero base. This isn't an
inconsistency per se, but older kernels can get confused by this and
corrupt the block, leading to corruption.
If we see this, flag the xattr structure for optimization so that it
gets rebuilt.
Cc: <stable@vger.kernel.org> # v4.15
Fixes: 13791d3b83 ("xfs: scrub extended attribute leaf space")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Check for erroneous overlapping freemap regions and collisions between
freemap regions and the xattr leaf entry array.
Note that we must explicitly zero out the extra freemaps in
xfs_attr3_leaf_compact so that the in-memory buffer has a correctly
initialized freemap array to satisfy the new verification code, even if
subsequent code changes the contents before unlocking the buffer.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Replace all the open-coded callsites with a single static inline helper.
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
xfs/592 and xfs/794 both trip this assertion in the leaf block freemap
adjustment code after ~20 minutes of running on my test VMs:
ASSERT(ichdr->firstused >= ichdr->count * sizeof(xfs_attr_leaf_entry_t)
+ xfs_attr3_leaf_hdr_size(leaf));
Upon enabling quite a lot more debugging code, I narrowed this down to
fsstress trying to set a local extended attribute with namelen=3 and
valuelen=71. This results in an entry size of 80 bytes.
At the start of xfs_attr3_leaf_add_work, the freemap looks like this:
i 0 base 448 size 0 rhs 448 count 46
i 1 base 388 size 132 rhs 448 count 46
i 2 base 2120 size 4 rhs 448 count 46
firstused = 520
where "rhs" is the first byte past the end of the leaf entry array.
This is inconsistent -- the entries array ends at byte 448, but
freemap[1] says there's free space starting at byte 388!
By the end of the function, the freemap is in worse shape:
i 0 base 456 size 0 rhs 456 count 47
i 1 base 388 size 52 rhs 456 count 47
i 2 base 2120 size 4 rhs 456 count 47
firstused = 440
Important note: 388 is not aligned with the entries array element size
of 8 bytes.
Based on the incorrect freemap, the name area starts at byte 440, which
is below the end of the entries array! That's why the assertion
triggers and the filesystem shuts down.
How did we end up here? First, recall from the previous patch that the
freemap array in an xattr leaf block is not intended to be a
comprehensive map of all free space in the leaf block. In other words,
it's perfectly legal to have a leaf block with:
* 376 bytes in use by the entries array
* freemap[0] has [base = 376, size = 8]
* freemap[1] has [base = 388, size = 1500]
* the space between 376 and 388 is free, but the freemap stopped
tracking that some time ago
If we add one xattr, the entries array grows to 384 bytes, and
freemap[0] becomes [base = 384, size = 0]. So far, so good. But if we
add a second xattr, the entries array grows to 392 bytes, and freemap[0]
gets pushed up to [base = 392, size = 0]. This is bad, because
freemap[1] hasn't been updated, and now the entries array and the free
space claim the same space.
The fix here is to adjust all freemap entries so that none of them
collide with the entries array. Note that this fix relies on commit
2a2b5932db ("xfs: fix attr leaf header freemap.size underflow") and
the previous patch that resets zero length freemap entries to have
base = 0.
Cc: <stable@vger.kernel.org> # v2.6.12
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Back in commit 2a2b5932db ("xfs: fix attr leaf header freemap.size
underflow"), Brian Foster observed that it's possible for a small
freemap at the end of the end of the xattr entries array to experience
a size underflow when subtracting the space consumed by an expansion of
the entries array. There are only three freemap entries, which means
that it is not a complete index of all free space in the leaf block.
This code can leave behind a zero-length freemap entry with a nonzero
base. Subsequent setxattr operations can increase the base up to the
point that it overlaps with another freemap entry. This isn't in and of
itself a problem because the code in _leaf_add that finds free space
ignores any freemap entry with zero size.
However, there's another bug in the freemap update code in _leaf_add,
which is that it fails to update a freemap entry that begins midway
through the xattr entry that was just appended to the array. That can
result in the freemap containing two entries with the same base but
different sizes (0 for the "pushed-up" entry, nonzero for the entry
that's actually tracking free space). A subsequent _leaf_add can then
allocate xattr namevalue entries on top of the entries array, leading to
data loss. But fixing that is for later.
For now, eliminate the possibility of confusion by zeroing out the base
of any freemap entry that has zero size. Because the freemap is not
intended to be a complete index of free space, a subsequent failure to
find any free space for a new xattr will trigger block compaction, which
regenerates the freemap.
It looks like this bug has been in the codebase for quite a long time.
Cc: <stable@vger.kernel.org> # v2.6.12
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Sinc commit 79a6d1bfe1 ("can: gs_usb: gs_usb_receive_bulk_callback():
unanchor URL on usb_submit_urb() error") a failing resubmit URB will print
an info message.
In the case of a short read where netdev has not yet been assigned,
initialize as NULL to avoid dereferencing an undefined value. Also report
the error value of the failed resubmit.
Fixes: 79a6d1bfe1 ("can: gs_usb: gs_usb_receive_bulk_callback(): unanchor URL on usb_submit_urb() error")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20260119181904.1209979-1-kuba@kernel.org/
Link: https://patch.msgid.link/20260120-gs_usb-fix-error-message-v1-1-6be04de572bc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce a new command for KVM_MEMORY_ENCRYPT_OP ioctl that can be used
to enable fetching of endorsement key certificates from userspace via
the new KVM_EXIT_SNP_REQ_CERTS exit type. Also introduce a new
KVM_X86_SEV_SNP_REQ_CERTS KVM device attribute so that userspace can
query whether the kernel supports the new command/exit.
Suggested-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Tested-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Link: https://patch.msgid.link/20260109231732.1160759-3-michael.roth@amd.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
For SEV-SNP, the host can optionally provide a certificate table to the
guest when it issues an attestation request to firmware (see GHCB 2.0
specification regarding "SNP Extended Guest Requests"). This certificate
table can then be used to verify the endorsement key used by firmware to
sign the attestation report.
While it is possible for guests to obtain the certificates through other
means, handling it via the host provides more flexibility in being able
to keep the certificate data in sync with the endorsement key throughout
host-side operations that might resulting in the endorsement key
changing.
In the case of KVM, userspace will be responsible for fetching the
certificate table and keeping it in sync with any modifications to the
endorsement key by other userspace management tools. Define a new
KVM_EXIT_SNP_REQ_CERTS event where userspace is provided with the GPA of
the buffer the guest has provided as part of the attestation request so
that userspace can write the certificate data into it while relying on
filesystem-based locking to keep the certificates up-to-date relative to
the endorsement keys installed/utilized by firmware at the time the
certificates are fetched.
[Melody: Update the documentation scheme about how file locking is
expected to happen.]
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Tested-by: Liam Merwick <liam.merwick@oracle.com>
Tested-by: Dionna Glaze <dionnaglaze@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Melody Wang <huibo.wang@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Link: https://patch.msgid.link/20260109231732.1160759-2-michael.roth@amd.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Drop the sanity check in kvm_apic_accept_events() that attempts to detect
KVM bugs by asserting that a vCPU isn't in Wait-For-SIPI if INIT/SIPI are
blocked, because if INIT is blocked, then it should be impossible for a
vCPU to get into WFS in the first place. Unfortunately, syzbot is smarter
than KVM (and its maintainers), and circumvented the guards put in place
by commit 0fe3e8d804 ("KVM: x86: Move INIT_RECEIVED vs. INIT/SIPI blocked
check to KVM_RUN") by swapping the order and stuffing VMXON after INIT, and
then triggering kvm_apic_accept_events() by way of KVM_GET_MP_STATE.
Simply drop the WARN as it hasn't detected any meaningful KVM bugs in
years (if ever?), and preventing userspace from clobbering guest state is
generally a non-goal. More importantly, fully closing the hole would
likely require enforcing some amount of ordering in KVM's ioctls, which is
a much bigger risk than simply deleting the WARN.
Reported-by: syzbot+59f2c3a3fc4f6c09b8cd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6925da1b.a70a0220.d98e3.00b0.GAE@google.com
Link: https://patch.msgid.link/20260123022816.2283567-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
xe:
- Disallow bind-queue sharing across multiple VMs
- Fix xe userptr in the absence of CONFIG_DEVICE_PRIVATE
- Fix a missed page count update
- Fix a confused argument to alloc_workqueue()
- Kernel-doc fixes
- Disable a workaround on VFs
- Fix a job lock assert
- Update wedged.mode only after successful reset policy change
- Select CONFIG_DEVICE_PRIVATE when DRM_XE_GPUSVM is selected
amdgpu:
- fix color pipeline string leak
- GC 12 fix
- Misc error path fixes
- DC analog fix
- SMU 6 fixes
- TLB flush fix
- DC idle optimization fix
amdkfd:
- GC 11 cooperative launch fix
imagination:
- sync wait for logtype update completion to ensure FW trace is
available
bridge/synopsis:
- Fix error paths in dw_dp_bind
nouveau:
- Add and implement missing DSB connector types, and improve unknown
connector handling.
- Set missing atomic function ops.
intel:
- place 3D lut at correct place in pipeline
- fix color pipeline string leak
vkms:
- fix color pipeline string leak
mediatek:
- Fix platform_get_irq() error checking
- HDMI DDC v2 driver fixes
- dpi: Find next bridge during probe
- mtk_gem: Partial refactor and use drm_gem_dma_object
- dt-bindings: Fix typo 'hardwares' to 'hardware'
-----BEGIN PGP SIGNATURE-----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=Ur9f
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2026-01-23' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Probably a good thing you decided to do an rc8 in this round. Nothing
stands out, but xe/amdgpu and mediatek all have a bunch of fixes, and
then there are a few other single patches. Hopefully next week is
calmer for release.
xe:
- Disallow bind-queue sharing across multiple VMs
- Fix xe userptr in the absence of CONFIG_DEVICE_PRIVATE
- Fix a missed page count update
- Fix a confused argument to alloc_workqueue()
- Kernel-doc fixes
- Disable a workaround on VFs
- Fix a job lock assert
- Update wedged.mode only after successful reset policy change
- Select CONFIG_DEVICE_PRIVATE when DRM_XE_GPUSVM is selected
amdgpu:
- fix color pipeline string leak
- GC 12 fix
- Misc error path fixes
- DC analog fix
- SMU 6 fixes
- TLB flush fix
- DC idle optimization fix
amdkfd:
- GC 11 cooperative launch fix
imagination:
- sync wait for logtype update completion to ensure FW trace
is available
bridge/synopsis:
- Fix error paths in dw_dp_bind
nouveau:
- Add and implement missing DSB connector types, and improve
unknown connector handling
- Set missing atomic function ops
intel:
- place 3D lut at correct place in pipeline
- fix color pipeline string leak
vkms:
- fix color pipeline string leak
mediatek:
- Fix platform_get_irq() error checking
- HDMI DDC v2 driver fixes
- dpi: Find next bridge during probe
- mtk_gem: Partial refactor and use drm_gem_dma_object
- dt-bindings: Fix typo 'hardwares' to 'hardware'"
* tag 'drm-fixes-2026-01-23' of https://gitlab.freedesktop.org/drm/kernel: (38 commits)
Revert "drm/amd/display: pause the workload setting in dm"
drm/xe: Select CONFIG_DEVICE_PRIVATE when DRM_XE_GPUSVM is selected
drm, drm/xe: Fix xe userptr in the absence of CONFIG_DEVICE_PRIVATE
drm/i915/display: Fix color pipeline enum name leak
drm/vkms: Fix color pipeline enum name leak
drm/amd/display: Fix color pipeline enum name leak
drm/i915/color: Place 3D LUT after CSC in plane color pipeline
drm/nouveau/disp: Set drm_mode_config_funcs.atomic_(check|commit)
drm/nouveau: implement missing DCB connector types; gracefully handle unknown connectors
drm/nouveau: add missing DCB connector types
drm/amdgpu: fix type for wptr in ring backup
drm/amdgpu: Fix validating flush_gpu_tlb_pasid()
drm/amd/pm: Workaround SI powertune issue on Radeon 430 (v2)
drm/amd/pm: Don't clear SI SMC table when setting power limit
drm/amd/pm: Fix si_dpm mmCG_THERMAL_INT setting
drm/xe: Update wedged.mode only after successful reset policy change
drm/xe/migrate: fix job lock assert
drm/xe/uapi: disallow bind queue sharing
drm/amd/display: Only poll analog connectors
drm/amdgpu: fix error handling in ib_schedule()
...
Some distributions (such as Ubuntu) configure GCC so that
_FORTIFY_SOURCE is automatically enabled at -O1 or above. This results
in some fortified version of definitions of standard library functions
are included. While linker resolves the symbols, the fortified versions
might override the definitions in lib/string_override.c and reference to
those PLT entries in GLIBC. This is not a problem for the code in host,
but it is a disaster for the guest code. E.g., if build and run
x86/nested_emulation_test on Ubuntu 24.04 will encounter a L1 #PF due to
memset() reference to __memset_chk@plt.
The option -fno-builtin-memset is not helpful here, because those
fortified versions are not built-in but some definitions which are
included by header, they are for different intentions.
In order to eliminate the unpredictable behaviors may vary depending on
the linker and platform, add the "-U_FORTIFY_SOURCE" into CFLAGS to
prevent from introducing the fortified definitions.
Signed-off-by: Zhiquan Li <zhiquan_li@163.com>
Link: https://patch.msgid.link/20260122053551.548229-1-zhiquan_li@163.com
Fixes: 6b6f71484b ("KVM: selftests: Implement memcmp(), memcpy(), and memset() for guest use")
Cc: stable@vger.kernel.org
[sean: tag for stable]
Signed-off-by: Sean Christopherson <seanjc@google.com>
On the embedded platform, certain critical data, such as IMU data, is
transmitted through UART. The tty_flip_buffer_push() interface in the TTY
layer uses system_dfl_wq to handle the flipping of the TTY buffer.
Although the unbound workqueue can create new threads on demand and wake
up the kworker thread on an idle CPU, it may be preempted by real-time
tasks or other high-prio tasks.
flush_to_ldisc() needs to wake up the relevant data handle thread. When
executing __wake_up_common_lock(), it calls spin_lock_irqsave(), which
does not disable preemption but disables migration in RT-Linux. This
prevents the kworker thread from being migrated to other cores by CPU's
balancing logic, resulting in long delays. The call trace is as follows:
__wake_up_common_lock
__wake_up
ep_poll_callback
__wake_up_common
__wake_up_common_lock
__wake_up
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf
tty_port_default_receive_buf
flush_to_ldisc
In our system, the processing interval for each frame of IMU data
transmitted via UART can experience significant jitter due to this issue.
Instead of the expected 10 to 15 ms frame processing interval, we see
spikes up to 30 to 35 ms. Moreover, in just one or two hours, there can
be 2 to 3 occurrences of such high jitter, which is quite frequent. This
jitter exceeds the software's tolerable limit of 20 ms.
Introduce flip_wq in tty_port which can be set by tty_port_link_wq() or as
default linked to default workqueue allocated when tty_register_driver().
The default workqueue is allocated with flag WQ_SYSFS, so that cpumask and
nice can be set dynamically. The execution timing of tty_port_link_wq() is
not clearly restricted. The newly added function tty_port_link_driver_wq()
checks whether the flip_wq of the tty_port has already been assigned when
linking the default tty_driver's workqueue to the port. After the user has
set a custom workqueue for a certain tty_port using tty_port_link_wq(), the
system will only use this custom workqueue, even if tty_driver does not
have %TTY_DRIVER_CUSTOM_WORKQUEUE flag.
Introduce %TTY_DRIVER_CUSTOM_WORKQUEUE flag meaning not to create the
default single tty_driver workqueue. Two reasons why need to introduce the
%TTY_DRIVER_CUSTOM_WORKQUEUE flag:
1. If the WQ_SYSFS parameter is enabled, workqueue_sysfs_register() will
fail when trying to create a workqueue with the same name. The pty is an
example of this; if both CONFIG_LEGACY_PTYS and CONFIG_UNIX98_PTYS are
enabled, the call to tty_register_driver() in unix98_pty_init() will fail.
2. Different tty ports may be used for different tasks, which may require
separate core binding control via workqueues. In this case, the workqueue
created by default in the tty driver is unnecessary. Enabling this flag
prevents the creation of this redundant workqueue.
After applying this patch, we can set the related UART TTY flip buffer
workqueue by sysfs. We set the cpumask to CPU cores associated with the
IMU tasks, and set the nice to -20. Testing has shown significant
improvement in the previously described issue, with almost no stuttering
occurring anymore.
Signed-off-by: Xin Zhao <jackzxcui1989@163.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20251223034836.2625547-1-jackzxcui1989@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As comments mentioned this is old (and actually deprecated) interface
to set custom baud rates. This interface has limitations as it only
allows to set a single opaque value called "custom_divisor". If the HW
needs more complex settings (like fractional divisor) it must somehow
encode this. This is horrid interface that is very driver specific
and not flexible. Meanwhile Linux has established way to set free
baud rate settings via BOTHER [1]. With all this being said, remove
deprecated interface for good.
Link: https://stackoverflow.com/questions/12646324/how-can-i-set-a-custom-baud-rate-on-linux [1]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260122102349.2395423-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SCIF binding documentation for Renesas RZ/G3L SoC. SCIF block on the
RZ/G3L is identical to one found on the RZ/G3S SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://patch.msgid.link/20260120125232.349708-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In TI K3 SoCs, I/O daisy chaining is used to allow wakeup from UART when the
UART controller is off. Set UART device as wakeup capable using out-of-band
wakeup if the 'wakeup' pinctrl state exists and the device may wakeup.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Kendall Willis <k-willis@ti.com>
Link: https://patch.msgid.link/20260116-uart-wakeup-v2-1-0078ae9996e4@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit bfc467db60 ("serial: remove redundant
tty_port_link_device()") because the tty_port_link_device() is not
redundant: the tty->port has to be confured before we call
uart_configure_port(), otherwise user-space can open console without TTY
linked to the driver.
This tty_port_link_device() was added explicitly to avoid this exact
issue in commit fb2b90014d ("tty: link tty and port before configuring
it as console"), so offending commit basically reverted the fix saying
it is redundant without addressing the actual race condition presented
there.
Reproducible always as tty->port warning on Qualcomm SoC with most of
devices disabled, so with very fast boot, and one serial device being
the console:
printk: legacy console [ttyMSM0] enabled
printk: legacy console [ttyMSM0] enabled
printk: legacy bootconsole [qcom_geni0] disabled
printk: legacy bootconsole [qcom_geni0] disabled
------------[ cut here ]------------
tty_init_dev: ttyMSM driver does not set tty->port. This would crash the kernel. Fix the driver!
WARNING: drivers/tty/tty_io.c:1414 at tty_init_dev.part.0+0x228/0x25c, CPU#2: systemd/1
Modules linked in: socinfo tcsrcc_eliza gcc_eliza sm3_ce fuse ipv6
CPU: 2 UID: 0 PID: 1 Comm: systemd Tainted: G S 6.19.0-rc4-next-20260108-00024-g2202f4d30aa8 #73 PREEMPT
Tainted: [S]=CPU_OUT_OF_SPEC
Hardware name: Qualcomm Technologies, Inc. Eliza (DT)
...
tty_init_dev.part.0 (drivers/tty/tty_io.c:1414 (discriminator 11)) (P)
tty_open (arch/arm64/include/asm/atomic_ll_sc.h:95 (discriminator 3) drivers/tty/tty_io.c:2073 (discriminator 3) drivers/tty/tty_io.c:2120 (discriminator 3))
chrdev_open (fs/char_dev.c:411)
do_dentry_open (fs/open.c:962)
vfs_open (fs/open.c:1094)
do_open (fs/namei.c:4634)
path_openat (fs/namei.c:4793)
do_filp_open (fs/namei.c:4820)
do_sys_openat2 (fs/open.c:1391 (discriminator 3))
...
Starting Network Name Resolution...
Apparently the flow with this small Yocto-based ramdisk user-space is:
driver (qcom_geni_serial.c): user-space:
============================ ===========
qcom_geni_serial_probe()
uart_add_one_port()
serial_core_register_port()
serial_core_add_one_port()
uart_configure_port()
register_console()
|
| open console
| ...
| tty_init_dev()
| driver->ports[idx] is NULL
|
tty_port_register_device_attr_serdev()
tty_port_link_device() <- set driver->ports[idx]
Fixes: bfc467db60 ("serial: remove redundant tty_port_link_device()")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://patch.msgid.link/20260123072139.53293-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for HSIC USB mode, which can be set for second USB controller
and PHY on Tegra SoC along with already supported UTMI or ULPI.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-3-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor to directly use enum usb_phy_interface to determine the PHY mode.
This change is in preparation for adding support for HSIC mode.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://patch.msgid.link/20260122151125.7367-2-clamor95@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode selection sequence is initiated by the driver after all partner
alternate modes have been successfully registered.
When a partner is disconnected, the driver also stops the mode selection
process and releases resources via `typec_mode_selection_delete`.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-8-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ucsi port driver supports modes selection, it should implement
`add_partner_altmodes` and `remove_partner_altmodes` ucsi operations. With
these operations the driver can manage the mode selection process.
Once partner altmodes are registered, `add_partner_altmodes` is called to
start the mode selection. When the partner is unregistered,
`remove_partner_altmodes` is supposed to stop any ongoing processes and
clean up the resources.
`typec_altmode_state_update` informes mode selection about the current mode
of the Type-C connector.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-7-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port driver sets this bit for an alternate mode description to indicate
support for the mode selection feature. Once set, individual Alt Mode
drivers will no longer attempt to activate their respective modes within
their probe functions. This prevents race conditions and non-prioritized
activation.
The bit is not set by default. If left unset, the system retains the
current behavior where Alt Mode drivers manage their own activation logic.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-6-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode selection process is controlled by the following API functions,
which allow to initiate and complete mode entry based on the priority of
each mode:
`typec_mode_selection_start` function compiles a priority list of supported
Alternate Modes.
`typec_altmode_state_update` function is invoked by the port driver to
communicate the current mode of the Type-C connector.
`typec_mode_selection_delete` function stops the currently running mode
selection process and releases all associated system resources.
`mode_selection_work_fn` task attempts to activate modes. The process stops
on success; otherwise, it proceeds to the next mode after a timeout or
error.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-5-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a priority sysfs attribute to the USB Type-C
alternate mode port interface. This new attribute allows user-space to
configure the numeric priority of alternate modes managing their preferred
order of operation. If a new priority value conflicts with an existing
mode's priority, the priorities of the conflicting mode and all subsequent
modes are automatically incremented to ensure uniqueness.
Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/20260119131824.2529334-4-akuchynski@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
