The DMA IRQ handler does not accounts for the overrun(OE) or any other
errors being reported by the IP before triggering a DMA transaction which
leads to the interrupts not being handled resulting into an IRQ storm.
The way to handle OE is to:
1. Reset the RX FIFO.
2. Read the UART_RESUME register, which clears the internal flag
Earlier, the driver issued DMA transations even in case of OE which shouldn't
be done according to the OE handling mechanism mentioned above, as we are
resetting the FIFO's, refer section: "12.1.6.4.8.1.3.6 Overrun During
Receive" [0].
[0] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Moteen Shah <m-shah@ti.com>
Link: https://patch.msgid.link/20260112081829.63049-2-m-shah@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "Non-8250 serial port support" menu so that entries in it
are displayed in a better order (_CONSOLE after its driver) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-4-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the "8250/16550 serial support" menu so that entries in it
are displayed in a better order (reorder a few symbols) and so that
intervening symbols don't break up the dependency list, allowing menu
entries to be displayed with proper indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-3-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1f4ea4838b ("mcb: Add missing modpost build support")
the MODULE_ALIAS() is redundant as the module alias is now
automatically generated from the MODULE_DEVICE_TABLE().
Remove the explicit alias.
No functional change intended.
Reviewed-by: Jorge Sanjuan Garcia <dev-jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Link: https://patch.msgid.link/20260108134110.25278-2-dev-josejavier.rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the serial communication interface (RSCI) used on the Renesas
RZ/V2H(P) (R9A09G057) and RZ/V2N (R9A09G056) SoCs. These SoCs integrate
the same RSCI IP block as the RZ/G3E (R9A09G047), so the RZ/G3E
compatible is used as a fallback for both.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251222162909.155279-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Qualcomm Glymur platform the PCIe host is compatible with the DWC
controller present on the X1E80100 platform. So document the PCIe
controllers found on Glymur and use the X1E80100 compatible string as a
fallback in the schema.
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Wenbin Yao <wenbin.yao@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250825-glymur_pcie5-v3-2-5c1d1730c16f@oss.qualcomm.com
Convert the Android Goldfish QEMU Pipe binding to DT schema format.
Move the file to the misc directory as it represents a miscellaneous
communication device.
Update the example node name to 'pipe' to comply with generic node
naming standards and fix the mismatch between unit address and reg
property in the original example.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20260113092602.3197681-3-visitorckw@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns (or errors with CONFIG_WERROR=y):
fs/ntfs3/inode.c:1021:6: error: variable 'folio' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
1021 | if (is_resident(ni)) {
| ^~~~~~~~~~~~~~~
fs/ntfs3/inode.c:1024:48: note: uninitialized use occurs here
1024 | while ((folio = writeback_iter(mapping, wbc, folio, &err)))
| ^~~~~
folio should be initialized to NULL for the first iteration of
writeback_iter() to start the loop properly. Restore the NULL
initialization of folio that was lost in the recent iomap conversion to
clear up the warning.
Fixes: 099ef9a ("fs/ntfs3: implement iomap-based file operations")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/oe-kbuild-all/202601010644.FIhOXy6Y-lkp@intel.com/
Closes: https://lore.kernel.org/r/202601010513.axd56bks-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
[almaz.alexandrovich@paragon-software.com: added a few more tags]
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Split multiple assignments in a single line into separate statements in
osdep_service.c to follow kernel coding style.
No functional change.
Signed-off-by: Nayana Mariyappa <nayana.mariyappa@gmail.com>
Link: https://patch.msgid.link/20260116120511.48272-5-nayana.mariyappa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added blank lines after variable declarations in osdep_service.c and related
files to improve readability and follow kernel coding style.
No functional change.
Signed-off-by: Nayana Mariyappa <nayana.mariyappa@gmail.com>
Link: https://patch.msgid.link/20260116120511.48272-4-nayana.mariyappa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed multi-line block comments in osdep_service.c to follow kernel
coding style. Fixing the non-kernel-doc comment has been merged into this
patch.
No functional change.
Signed-off-by: Nayana Mariyappa <nayana.mariyappa@gmail.com>
Link: https://patch.msgid.link/20260116120511.48272-2-nayana.mariyappa@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix spacing around operators and type casts in rtw_xmit.c to
comply with the kernel coding style.
Signed-off-by: Khushal Chitturi <khushalchitturi@gmail.com>
Link: https://patch.msgid.link/20260116053052.4198-2-khushalchitturi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cfg80211_inform_bss_frame() may return NULL on failure. In that case,
the allocated buffer 'buf' is not freed and the function returns early,
leading to potential memory leak.
Fix this by ensuring that 'buf' is freed on both success and failure paths.
Signed-off-by: Diksha Kumari <dikshakdevgan@gmail.com>
Reviewed-by: Mukesh Kumar Chaurasiya <mkchauras@linux.ibm.com>
Link: https://patch.msgid.link/20260113091712.7071-1-dikshakdevgan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return 0 from disable_streams, use div_u64() instead of do_div(), use
dev_dbg() for a debug message and move loop variable definition into the
loop itself.
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
This patch sets the current exposure time as maximum for the
flash_duration control. As Flash/Strobes which are longer than the
exposure time have no effect.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
[Sakari Ailus: Some lines rewrapped.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
As the granularity of the hardware supported values is lower than the
control value, implement a try_ctrl() function for
V4L2_CID_FLASH_DURATION. This function calculates the nearest possible
µs strobe duration for the given value and returns it back to the
caller.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add V4L2_CID_FLASH_DURATION support using the "strobe_frame_span"
feature of the sensor. This is implemented by transforming the given µs
value by an interpolated formula to a "span step width" value and
writing it to register PWM_CTRL_25, PWM_CTRL_26, PWM_CTRL_27,
PWM_CTRL_28 (0x3925, 0x3926, 0x3927, 0x3928).
The maximum control value is set to the period of the current default
framerate.
All register values are based on the OV9281 datasheet v1.53 (jan 2019)
and tested using an ov9281 VisionComponents module.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
[Sakari Ailus: Remove redundant assignment of ret, declare ret as last.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add V4L2_CID_FLASH_STROBE_OE enable/disable support using the
"strobe output enable" feature of the sensor.
All values are based on the OV9281 datasheet v1.53 (january 2019) and
tested using an ov9281 VisionComponents module.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add #define's for the output enable registers (0x3004, 0x3005, 0x3006),
also known as SC_CTRL_04, SC_CTRL_05, SC_CTRL_04. Use those register
definitions instead of the raw values in the `common_regs` struct.
All values are based on the OV9281 datasheet v1.53 (january 2019).
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add the new strobe duration and hardware strobe output enable to v4l
uAPI documentation. Additionally add labels for cross-referencing v4l
controls.
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add a control V4L2_CID_FLASH_STROBE_OE to en- or disable the
strobe output of v4l2 devices (most likely sensors).
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add a V4L2_CID_FLASH_DURATION control to set the duration of a
flash/strobe pulse. This controls the length of the flash/strobe pulse
output by device (typically a camera sensor) and connected to the flash
controller. This is different to the V4L2_CID_FLASH_TIMEOUT control,
which is implemented by the flash controller and defines a limit after
which the flash is "forcefully" turned off again.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The imx219_update_pad_format() is short and called from a single place,
in imx219_set_pad_format(). Inline the code in the caller to keep all
format adjustments grouped in a single place and improve readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Prepare for adding more media bus codes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
ccs_propagate() no longer stores information in the driver's context
struct. The which parameter can thus be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Compute scaling configuration from sub-device state instead of storing it
to the driver's device context struct.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Calculate binning configuration from sub-device state so the state related
configuration can be removed from the driver's device context struct.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Replace the use of mutex_{,un}lock() by guard() and scoped_guard() where
it makes sense (i.e. everywhere).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Rely on sub-device state locking to serialise access to driver's data
structures. The driver-provided mutex is used as the state lock for all
driver sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
As it's now easier to obtain the necessary information on crop and compose
rectangles after moving to sub-device state, remove the
ccs_get_crop_compose helper.
Also remove the comp arguments of the compose goodness calculators and
make related local variables and function arguments const where
applicable.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Digital gain wraps-around at the maximum of 16838 / 0x3fff.
Fix the maximum digital gain by setting it to 0x3fff.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Reviewed-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Fixes: 0827b58dab ("media: i2c: add ov01a10 image sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Fix indentation in ov01a10_get_pm_resources().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove Hongju's e-mail address that no longer works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The struct dcmipp_bytecap_device embeds a cmier variable which is
actually only set once and then used in several places for interrupt
mask or interrupt enable/disable. Use the DCMIPP_CMIER_P0ALL
bitfield macro directly instead of using it through the cmier
variable.
There is also no need to mask again vcap->cmsr2 against enabled
interrupts bit since this has already been done when storing the
interrupt status into the cmsr2 variable.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Since the byteproc is working at byte level, it is not possible to
perform decimation with formats other than 8 or 16 bit per pixel.
Ensure any other format won't be able to set a compose.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
DCMIPP can handle Y8 to Y14 input formats however until now only
Y8 was handled. Add support for Y10-Y12-Y14 in all relevant
subdevs.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add entries within several subdevs in order to handle RGB888 format.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Avoid possibility to perform compose on all frames which mbus code is
within the bayer range or jpeg format.
Fixes: 822c72eb15 ("media: stm32: dcmipp: add bayer 10~14 bits formats")
Cc: stable@vger.kernel.org
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Ensure that there are no pending interrupts after we have stopped the
pipeline. Indeed, it could happen that new interrupt has been generated
during the stop_streaming processing hence clear them in order to avoid
getting a new interrupt right from the start of a next start_streaming.
Fixes: 28e0f37722 ("media: stm32-dcmipp: STM32 DCMIPP camera interface driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
adv7604 and et8ek8 sensor drivers have mixed up logical and line level
for reset/powerdown signal. They call it a reset signal (it indeed
behaves like that), but drivers assert the reset to operate which is
clearly incorrect and relies on wrong ACTIVE_HIGH flag in the DTS.
People in discussions copy existing poor code and claim they can repeat
same mistake, so add a note to prevent that.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
When DCMIPP requires only a single clock (kclk), avoid relying on its
name to obtain it. The introduction of MP25 support added the mclk,
which necessitated naming the first clock kclk. However, this breaks
backward compatibility with existing MP13 device trees that do not
specify clock names.
Fixes: 686f27f7ea ("media: stm32: dcmipp: add core support for the stm32mp25")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Cc: Stable@vger.kernel.org # 6.14.x: 7f487562af49 media: stm32: dcmipp: correct ret type in dcmipp_graph_notify_bound
Cc: Stable@vger.kernel.org # 6.14.x: c715dd62da30 media: stm32: dcmipp: add has_csi2 & needs_mclk in match data
Cc: Stable@vger.kernel.org # 6.14.x:
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Move Rui Miguel Silva to reviewer since he does not have sufficient time to
maintain i.MX7/8 media drivers. Frank Li has the hardware, complete
documentation, and has participated actively in patch review. Promote him
as the i.MX7/8 media drivers maintainer.
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
We need to set correct mode for PLL to calculate correct frequency.
Signalling mode is known at this point, so use it for that.
Fixes: 47b6eaf36e ("media: ccs-pll: Differentiate between CSI-2 D-PHY and C-PHY")
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
[Sakari Ailus: Drop extra newline.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Rely on devm_v4l2_sensor_clk_get() to obtain the sensor's external clock.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Fix coding style issues and do other small cleanups in ccs_get_hwcfg().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Switch from s_stream to enable_streams and disable_streams callbacks.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
