The delete on last close functionality can now only be tested properly
by using multiple threads to hold open the variable files and testing
what happens as they complete.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Changing voltage might ignore slew rate and cause a current surge.
With current implementation the driver will get the regulator to change
the voltage range used during run time. According to communication I
have had with Texas Instruments, this is not intended, since the
Dynamic Voltage Scaling in the hardware is only designed to work
within a voltage range. The current implementation will therefore
ignore the slew rate that is defined in devicetree when the voltage
range is changed during use.
The current implementation will always select a voltage in the most
accurate range that can reach that voltage even though multiple ranges
are able to reach that voltage. There are 4 Voltage ranges with the
following reach:
0b00: 0.4-0.71875V (1.25mV step size)
0b01: 0.4-1.0375V (2.5mV)
0b10: 0.4-1.675V (5mV)
0b11: 0.8-3.3V (10mV)
This in practice means that a change from below to above 0.71875V will
use the smallest range(0b00) for the values below and the second
smallest range(0b01) for the voltages above (Up to 1.675V). I have
timed how long it takes to go from below 0.71875V to above. The
increase was 100mV which, with the slew rate set to 1250µV/µs. This
in theory should take 80µs to do. With the current implementation, it
takes 10µs on my hardware. Doing the same test with the slew rate set
to 5000µV/µs, which should take 20µs, also only takes 10µs to do on
my hardware. Not only is this not in line with the technical
specification for the regulator. It also causes a current surge. Which
when calculating the output current, as described in the technical
specification, compared to what I could observe on my hardware the real
output is ~1A higher (~1.2A) than what I calculated it to be(~0.2A).
I tested also transitioning from a bigger to a smaller range, and the
results were the same.
Instead, let's limit the voltage range to a single one, which is in
line with the intended use of the regulator. This is done by looking
up the minimum and maximum requested voltage specified in devicetree.
Signed-off-by: Jonas Andreasson <jonas.andreasson@axis.com>
Link: https://patch.msgid.link/20250121-tps-fix-v2-1-50cc4d0f1635@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit
9e2ab4b18e ("ASoC: rockchip: i2s-tdm: Fix inaccurate sampling rates"),
the set_sysclk callback was removed as considered unused as the mclk rate
can be set in the hw_params callback.
The difference between hw_params and set_sysclk is that the former is
called with the audio sampling rate set in the params (e.g.: 48000 Hz)
while the latter is called with a clock rate already computed with
sampling_rate * mclk-fs (e.g.: 48000 * 256)
For HDMI audio using the Rockchip I2S TDM driver, the mclk-fs value must
be set to 128 instead of the default 256, and that value is set in the
device tree at the machine driver level (like a simple-audio-card
compatible node).
Therefore, the i2s_tdm driver has no idea that another mclk-fs value can
be configured and simply computes the mclk rate in the hw_params callback
with DEFAULT_MCLK_FS * params_rate(params), which is wrong for HDMI
audio.
Re-add the set_sysclk callback so that the mclk rate is computed by the
machine driver which has the correct mclk-fs value set in its device tree
node.
Fixes: 9e2ab4b18e ("ASoC: rockchip: i2s-tdm: Fix inaccurate sampling rates")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Link: https://patch.msgid.link/20250117163102.65807-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have at least two options for how to do the
TRANS_PUSH_SEND + commit completion signalling
with the DSB:
Option A)
1. trigger TRANS_PUSH_SEND
2. wait for "safe window"
3. signal the interrupt
In this cases step 2 should not do anything if we were already
between vmin and vmax decision boundaries. Otherwise we'll wait
until the next start of the vblank period.
Option B)
1. wait for "safe window"
2. trigger TRANS_PUSH_SEND
3. signal the interrupt
This option is perhaps a bit less racy, but if we do somehow
screw up and the wait is a nop but the push gets deferred
until the next frame then we'll end up completing the commit
a frame too early.
So for now I'm leaning towards option A since losing the race
won't have any drastic consequences. To deal with the race we
can give the DSB a bit more time to start step 2 before the
hardware has started the vblank termination properly. Often
times it seems to be fast enough to make it in time even without
any extra vblank delay (the push is issued somewhere within a
scanline and it latches on the next scanline).
v2: Use intel_vrr_possible() to determine if we need some
vblank delay (also avoids adding it for DSI which doens't
actually program the transcoder registers correctly for it)
Cc: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116201637.22486-8-ville.syrjala@linux.intel.com
GOP might not agree with our idea of what the vblank delay should be.
Reuse the LRR codepaths to fix that up via a fastset.
The relevant registers aren't actually double buffered so this is a
little bit dodgy. While I've not seen any real issues from frobbing
these live, let's limit this to just the fastboot case (by only
allowing it when old_crtc_state->inherited==true).
Cc: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116201637.22486-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Update TRANS_SET_CONTEXT_LATENCY in intel_set_transcoder_timings_lrr()
as well. While for actual LRR updates this should not change, I want
to reuse this code to also sanitize the vblank delay during boot,
and in that case we do need to update this.
Cc: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116201637.22486-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I want to start using intel_set_transcoder_timings_lrr() also for
fixing up the vblank delay during boot. To that end make sure it
can cope with interlaced modes as well.
Note that we have soft-defeatured interlaced modes on tgl+ so
technically this is dead code, but if we ever have the need to
bring interlaced support back it seems better to handle this.
Cc: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116201637.22486-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
intel_set_transcoder_timings() will set TRANS_VBLANK.vblank_start to 0
for clarity on ADL+ (non-DSI) because the hardware no longer uses that
value. Do the same in intel_set_transcoder_timings_lrr() to make sure
the registers stay consistent even when doing LRR timing updates.
Cc: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116201637.22486-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Code for the DP tunnelling functionality in the xe driver can be
built only if the display code is also built, adjust the kconfig
dependency accordingly.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Fixes: 73900dce57 ("drm/xe/dp: Enable DP tunneling")
Reported-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117153843.1312303-1-imre.deak@intel.com
Checking for lockdep_assert_held(&ctx->uring_lock) in io_free_rsrc_node()
means that the assertion is only checked when the resource drops to zero
references.
Move the lockdep assertion up into the caller io_put_rsrc_node() so that it
instead happens on every reference count decrement.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20250120-uring-lockdep-assert-earlier-v1-1-68d8e071a4bb@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring_ctx parameter for io_rsrc_node_alloc() is unused for now.
This patch removes the parameter and fixes the callers accordingly.
Signed-off-by: Sidong Yang <sidong.yang@furiosa.ai>
Link: https://lore.kernel.org/r/20250115142033.658599-1-sidong.yang@furiosa.ai
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The locking in the buffer cloning code is somewhat complex because it goes
back and forth between locking the source ring and the destination ring.
Make it easier to reason about by locking both rings at the same time.
To avoid ABBA deadlocks, lock the rings in ascending kernel address order,
just like in lock_two_nondirectories().
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20250115-uring-clone-refactor-v2-1-7289ba50776d@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is already handled below in the code by fixup_initial_plane_config.
Fixes: a815362752 ("drm/i915: Try to relocate the BIOS fb to the start of ggtt")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210083111.230484-3-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
It was mentioned in a review that there is a possibility of choosing
to load the module with VF in execlists mode.
Of course this doesn't work, just bomb out as hard as possible.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210083111.230484-12-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
devm_clk_get_optional() returns NULL for missing clocks and a PTR_ERR()
if there is a clock but we fail to get it, but currently we only handle
the latter case and do so as though the clock was missing. If we get an
error back we should handle that as an error since the clock exists but
we failed to get it, if we get NULL then the clock doesn't exist and we
should handle that.
Fixes: 4c6ac5446d ("spi: omap2-mcspi: Fix the IS_ERR() bug for devm_clk_get_optional_enabled()")
Reported-by: Lars Pedersen <lapeddk@gmail.com>
Link: https://patch.msgid.link/20250117-spi-fix-omap2-optional-v1-1-e77d4ac6db6e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lars Pedersen <lapeddk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both kcryptd_io_read() and kcryptd_crypt_write_convert() will invoke
crypt_alloc_buffer() to allocate a new bio. Both of these two callers
initialize bi_iter.bi_sector for the new bio separatedly after
crypt_alloc_buffer() returns. However, kcryptd_crypt_write_convert()
will copy the bi_iter of the new bio into ctx.iter_out or ctx.iter_in.
Although it doesn't incur any harm now, it is better to fully initialize
bi_iter before it is used.
Therefore, initialize bi_iter.bi_sector in crypt_alloc_buffer() instead.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Both kcryptd_crypt_write_continue() and kcryptd_crypt_read_continue()
are running in the kworker context, it is OK to call cond_resched(),
Therefore, set atomic as false when invoking crypt_convert() under
kworker context.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
set_delayed() adjusts cfs_rq->h_nr_runnable for the hierarchy when an
entity is delayed irrespective of whether the entity corresponds to a
task or a cfs_rq.
Consider the following scenario:
root
/ \
A B (*) delayed since B is no longer eligible on root
| |
Task0 Task1 <--- dequeue_task_fair() - task blocks
When Task1 blocks (dequeue_entity() for task's se returns true),
dequeue_entities() will continue adjusting cfs_rq->h_nr_* for the
hierarchy of Task1. However, when the sched_entity corresponding to
cfs_rq B is delayed, set_delayed() will adjust the h_nr_runnable for the
hierarchy too leading to both dequeue_entity() and set_delayed()
decrementing h_nr_runnable for the dequeue of the same task.
A SCHED_WARN_ON() to inspect h_nr_runnable post its update in
dequeue_entities() like below:
cfs_rq->h_nr_runnable -= h_nr_runnable;
SCHED_WARN_ON(((int) cfs_rq->h_nr_runnable) < 0);
is consistently tripped when running wakeup intensive workloads like
hackbench in a cgroup.
This error is self correcting since cfs_rq are per-cpu and cannot
migrate. The entitiy is either picked for full dequeue or is requeued
when a task wakes up below it. Both those paths call clear_delayed()
which again increments h_nr_runnable of the hierarchy without
considering if the entity corresponds to a task or not.
h_nr_runnable will eventually reflect the correct value however in the
interim, the incorrect values can still influence PELT calculation which
uses se->runnable_weight or cfs_rq->h_nr_runnable.
Since only delayed tasks take the early return path in
dequeue_entities() and enqueue_task_fair(), adjust the
h_nr_runnable in {set,clear}_delayed() only when a task is delayed as
this path skips the h_nr_* update loops and returns early.
For entities corresponding to cfs_rq, the h_nr_* update loop in the
caller will do the right thing.
Fixes: 76f2f78329 ("sched/eevdf: More PELT vs DELAYED_DEQUEUE")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Tested-by: Swapnil Sapkal <swapnil.sapkal@amd.com>
Link: https://lkml.kernel.org/r/20250117105852.23908-1-kprateek.nayak@amd.com
When testing on my tiled display, initially the tiled display is
detected correctly:
[90376.523692] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] fallback: Not all outputs enabled
[90376.523713] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] Enabled: 0, detected: 2
...
[90376.523967] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (1920,0)
[90376.524020] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
But then, when modes have been set:
[90379.729525] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:287:DP-4] on [CRTC:82:pipe A]: 1920x2160
[90379.729640] xe 0000:67:00.0: [drm:drm_client_firmware_config.isra.0 [drm]] [CONNECTOR:289:DP-5] on [CRTC:134:pipe B]: 1920x2160
...
[90379.730036] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:82:pipe A] desired mode 1920x2160 set (0,0)
[90379.730124] xe 0000:67:00.0: [drm:drm_client_modeset_probe [drm]] [CRTC:134:pipe B] desired mode 1920x2160 set (0,0)
Call drm_client_get_tile_offsets() in drm_client_firmware_config() as
well, to ensure that the offset is set correctly.
This has to be done as a separate pass, as the tile order may not be
equal to the drm connector order.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
Tiled displays have a different x/y offset to begin with. Instead of
attempting to remember this, just apply a delta instead.
This fixes the first tile being duplicated on other tiles when vt
switching.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116142825.3933-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Cc: <stable@vger.kernel.org>
A specific allocation for the CRTC is not strictly necessary at this
point, but in order to implement dynamic configuration of VKMS (configFS),
it will be easier to have one allocation per CRTC.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-3-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
A specific allocation for the encoder is not strictly necessary at this
point, but in order to implement dynamic configuration of VKMS (configFS),
it will be easier to have one allocation per encoder.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-2-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
A specific allocation for the connector is not strictly necessary
at this point, but in order to implement dynamic configuration of
VKMS (configFS), it will be easier to have one allocation per
connector.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250117-b4-vkms-allocated-v4-1-8ec8fd21aaf6@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Currently we are forcing full modeset if Panel Replay mode is changed. This
is not necessary as long as we are not changing sink PANEL REPLAY ENABLE
bit in PANEL REPLAY ENABLE AND CONFIGURATION 1 register. This can be
achieved by entering Panel Replay inactive mode (Live Frame mode) when
Panel Replay is disabled and keep PANEL REPLAY ENABLE bit in PANEL REPLAY
ENABLE AND CONFIGURATION 1 enabled always if panel is just supporting Panel
Replay.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109103532.2093356-5-jouni.hogander@intel.com
Currently we are configuring Panel Replay on sink when it get's
enabled. This means we need to do full modeset when enabling Panel
Replay. This is required as DP specification is saying sink Panel Replay
needs to be configured before link training. Avoid full modeset by enabling
Panel Replay on sink always when it's supported by the sink and the
source.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109103532.2093356-3-jouni.hogander@intel.com
According to DP/eDP specification only DP_PANEL_REPLAY_ENABLE has to be set
prior link training. For this purpose add a new function which sets this
bit on sink side if Panel Replay is supported by the sink and the source.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250109103532.2093356-2-jouni.hogander@intel.com
The use of R7 in the SMCCC conflicts with the compiler's use of R7 as a frame
pointer in Thumb2 mode, which is forcibly enabled by Clang when profiling
hooks are inserted via the -pg switch.
This is a known issue and similar driver workaround this with a Makefile
ifdef. Exact workaround are applied in
drivers/firmware/arm_scmi/transports/Makefile and other similar driver.
Suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501201840.XmpHXpQ4-lkp@intel.com/
Fixes: 82e703dd43 ("pmdomain: airoha: Add Airoha CPU PM Domain support")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20250120153817.11807-1-ansuelsmth@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current VKMS driver uses non-managed function to create
writeback connectors. It is not an issue yet, but in order
to support multiple devices easily, convert this code to
use drm and device managed helpers.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-8-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
The current implementation of drm_writeback_connector initialization does
not properly clean up all resources in case of failure (allocated
properties and possible_encoders). Add this cleaning in case of failure.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-6-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
As the old drm and the new drmm variants of drm_writeback_connector
requires almost the same initialization, create an internal helper to do
most of the initialization work.
Currently there is no cleanup function for writeback connectors. To allows
implementation of drmm variant of writeback connector, create a cleanup
function that can be used to properly remove all the writeback-specific
properties and allocations.
This also introduce an helper to cleanup only the drm_writeback_connector
properties, so it can be used during initialization to cleanup in case of
failure.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-5-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
The current VKMS driver uses managed function to create crtc, but
don't use it to properly clean the crtc workqueue. It is not an
issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-4-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Add drmm_alloc_ordered_workqueue(), a helper that provides managed ordered
workqueue cleanup. The workqueue will be destroyed with the final
reference of the DRM device.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-3-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
The current VKMS driver uses non-managed function to create encoders. It
is not an issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-2-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
The current VKMS driver uses non-managed function to create connectors. It
is not an issue yet, but in order to support multiple devices easily,
convert this code to use drm and device managed helpers.
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250116-google-vkms-managed-v9-1-3e4ae1bd05a0@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
With vmalloc stack addresses enabled (CONFIG_VMAP_STACK=y) DCP trusted
keys can crash during en- and decryption of the blob encryption key via
the DCP crypto driver. This is caused by improperly using sg_init_one()
with vmalloc'd stack buffers (plain_key_blob).
Fix this by always using kmalloc() for buffers we give to the DCP crypto
driver.
Cc: stable@vger.kernel.org # v6.10+
Fixes: 0e28bf61a5 ("KEYS: trusted: dcp: fix leak of blob encryption key")
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The global variable pkcs7 does not exist.
Drop the variable declaration, but keep the struct prototype needed for
is_key_on_revocation_list().
Reported by clang:
./include/keys/system_keyring.h:104:67: warning: declaration shadows a variable in the global scope [-Wshadow]
104 | static inline int is_key_on_revocation_list(struct pkcs7_message *pkcs7)
| ^
./include/keys/system_keyring.h:76:30: note: previous declaration is here
76 | extern struct pkcs7_message *pkcs7;
| ^
Fixes: 56c5812623 ("certs: Add EFI_CERT_X509_GUID support for dbx entries")
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
i915 has this really nice, infrastructure where everything becomes
complicated, GGTT needs eviction, etc..
Lets not do that, and make the dumbest possible interface instead.
Try to retrieve the VMA from old_plane_state, or intel_fbdev if kernel
fb.
Link: https://patchwork.freedesktop.org/patch/msgid/20241206182032.196307-1-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Tested-by: Jani Saarinen <jani.saarinen@intel.com>