Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.
This controller however performed a frequency check, which is also
observed during the ->check_op() phase.
The per-operation frequency capability is thus advertised to the spi-mem
core.
Cc: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-3-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are spi devices with multiple frequency limitations depending on
the invoked command. We probably do not want to afford running at the
lowest supported frequency all the time, so if we want to get the most
of our hardware, we need to allow per-operation frequency limitations.
Among all the SPI memory controllers, I believe all are capable of
changing the spi frequency on the fly. Some of the drivers do not make
any frequency setup though. And some others will derive a per chip
prescaler value which will be used forever.
Actually changing the frequency on the fly is something new in Linux, so
we need to carefully flag the drivers which do and do not support it. A
controller capability is created for that, and the presence for this
capability will always be checked before accepting such pattern.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-2-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A very minor oversight that dates all the way back to rst migration in
commit 9d85025b04 ("docs-rst: create an user's manual book").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20241231190240.417446-1-lkundrak@v3.sk
Translate lwn/Documentation/security/landlock.rst into Chinese.
Update the translation through commit dad2f20715
("landlock: Fix grammar issues in documentation")
Signed-off-by: Yuxian Mao <maoyuxian@cqsoftware.com.cn>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250102104406.17600-1-maoyuxian@cqsoftware.com.cn
It's noticed when I myself made the same spelling mistake while
searching for localmodconfig
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Reviewed-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250103004358.1310121-1-lizhijian@fujitsu.com
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250109182303.3973082-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The guc_mmio_reg interface supports steering, but it is currently not
implemented. This will allow the GuC to control steering of MMIO
registers after save-restore and avoid reading from fused off MCR
register instances.
Fixes: 9c57bc0865 ("drm/xe/lnl: Drop force_probe requirement")
Signed-off-by: Jesus Narvaez <jesus.narvaez@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241212190100.3768068-1-jesus.narvaez@intel.com
Translate lwn/Documentation/security/siphash.rst into Chinese
Update the translation through commit 12fe434314
("Documentation: siphash: Fix typo in the name of offsetofend macro")
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: zhangwei <zhangwei@cqsoftware.com.cn>
Reviewed-by: Yanteng Si <siyanteng@linux.dev>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/0af3d9b8be0e5166f74bd36fd6b040767f767fce.1736315479.git.zhangwei@cqsoftware.com.cn
Translate .../security/IMA-templates.rst into Chinese.
Update the translation through commit 398c42e2c4
("ima: support fs-verity file digest based version 3 signatures").
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Shuo Zhao <zhaoshuo@cqsoftware.com.cn>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20250108075740.19342-1-zhaoshuo@cqsoftware.com.cn
-----BEGIN PGP SIGNATURE-----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=QYC1
-----END PGP SIGNATURE-----
Merge tag 'for-6.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes.
Besides the one-liners in Btrfs there's fix to the io_uring and
encoded read integration (added in this development cycle). The update
to io_uring provides more space for the ongoing command that is then
used in Btrfs to handle some cases.
- io_uring and encoded read:
- provide stable storage for io_uring command data
- make a copy of encoded read ioctl call, reuse that in case the
call would block and will be called again
- properly initialize zlib context for hardware compression on s390
- fix max extent size calculation on filesystems with non-zoned
devices
- fix crash in scrub on crafted image due to invalid extent tree"
* tag 'for-6.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zlib: fix avail_in bytes for s390 zlib HW compression path
btrfs: zoned: calculate max_extent_size properly on non-zoned setup
btrfs: avoid NULL pointer dereference if no valid extent tree
btrfs: don't read from userspace twice in btrfs_uring_encoded_read()
io_uring: add io_uring_cmd_get_async_data helper
io_uring/cmd: add per-op data to struct io_uring_cmd_data
io_uring/cmd: rename struct uring_cache to io_uring_cmd_data
Atish Patra <atishp@rivosinc.com> says:
Here are two minor improvement/fixes in the PMU event path. The first patch
was part of the series[1]. The 2nd patch was suggested during the series
review.
While the series can only be merged once SBI v3.0 is frozen, these two
patches can be independent of SBI v3.0 and can be merged sooner. Hence, these
two patches are sent as a separate series.
* b4-shazam-merge:
drivers/perf: riscv: Do not allow invalid raw event config
drivers/perf: riscv: Return error for default case
drivers/perf: riscv: Fix Platform firmware event data
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-0-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The SBI specification allows only lower 48bits of hpmeventX to be
configured via SBI PMU. Currently, the driver masks of the higher
bits but doesn't return an error. This will lead to an additional
SBI call for config matching which should return for an invalid
event error in most of the cases.
However, if a platform(i.e Rocket and sifive cores) implements a
bitmap of all bits in the event encoding this will lead to an
incorrect event being programmed leading to user confusion.
Report the error to the user if higher bits are set during the
event mapping itself to avoid the confusion and save an additional
SBI call.
Suggested-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-3-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
If the upper two bits has an invalid valid (0x1), the event mapping
is not reliable as it returns an uninitialized variable.
Return appropriate value for the default case.
Fixes: f0c9363db2 ("perf/riscv-sbi: Add platform specific firmware event handling")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-2-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Platform firmware event data field is allowed to be 62 bits for
Linux as uppper most two bits are reserved to indicate SBI fw or
platform specific firmware events.
However, the event data field is masked as per the hardware raw
event mask which is not correct.
Fix the platform firmware event data field with proper mask.
Fixes: f0c9363db2 ("perf/riscv-sbi: Add platform specific firmware event handling")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-1-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
This contains a pair of fixes for the vector self tests, which avoids
some warnings and provides proper status messages.
* b4-shazam-merge:
tools: selftests: riscv: Add test count for vstate_prctl
tools: selftests: riscv: Add pass message for v_initval_nolibc
Link: https://lore.kernel.org/r/20241220091730.28006-1-yongxuan.wang@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the test count to drop the warning message.
"Planned tests != run tests (0 != 1)"
Fixes: 7cf6198ce2 ("selftests: Test RISC-V Vector prctl interface")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Andy Chiu <AndybnAC@gmail.com>
Link: https://lore.kernel.org/r/20241220091730.28006-3-yongxuan.wang@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the pass message after we successfully complete the test.
Fixes: 5c93c4c72f ("selftests: Test RISC-V Vector's first-use handler")
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Andy Chiu <AndybnAC@gmail.com>
Link: https://lore.kernel.org/r/20241220091730.28006-2-yongxuan.wang@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
device_init_wakeup() second argument is a bool type. Use proper boolean
values when calling it to match the type and to produce unambiguous code
which is easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20241217071331.3607-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As reported by the kernel test robot, the following error occurs:
sound/soc/amd/yc/acp6x-mach.c: In function 'acp6x_probe':
>> sound/soc/amd/yc/acp6x-mach.c:573:15: error: implicit declaration of function 'acpi_evaluate_integer'; did you mean 'acpi_evaluate_object'? [-Werror=implicit-function-declaration]
573 | ret = acpi_evaluate_integer(handle, "_WOV", NULL, &dmic_status);
| ^~~~~~~~~~~~~~~~~~~~~
| acpi_evaluate_object
cc1: some warnings being treated as errors
The function 'acpi_evaluate_integer' and its prototype in 'acpi_bus.h'
are only available when 'CONFIG_ACPI' is enabled. Add a 'depends on ACPI'
directive in Kconfig to ensure proper compilation.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501090345.pBIDRTym-lkp@intel.com/
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Link: https://patch.msgid.link/20250109171547.362412-1-eleanor15x@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=PG5v
-----END PGP SIGNATURE-----
Merge tag 'nf-25-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix imbalance between flowtable BIND and UNBIND calls to configure
hardware offload, this fixes a possible kmemleak.
2) Clamp maximum conntrack hashtable size to INT_MAX to fix a possible
WARN_ON_ONCE splat coming from kvmalloc_array(), only possible from
init_netns.
* tag 'nf-25-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: clamp maximum hashtable size to INT_MAX
netfilter: nf_tables: imbalance in flowtable binding
====================
Link: https://patch.msgid.link/20250109123532.41768-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
net: sysctl: avoid using current->nsproxy
As pointed out by Al Viro and Eric Dumazet in [1], using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns as it is usually done. This could cause
unexpected issues when other operations are done on the wrong netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' or 'pernet' structure can be obtained from the table->data
using container_of().
Note that table->data could also be used directly in more places, but
that would increase the size of this fix to replace all accesses via
'net'. Probably best to avoid that for fixes.
Patches 2-9 remove access of net via current->nsproxy in sysfs handlers
in MPTCP, SCTP and RDS. There are multiple patches doing almost the same
thing, but the reason is to ease the backports.
Patch 1 is not directly linked to this, but it is a small fix for MPTCP
available_schedulers sysctl knob to explicitly mark it as read-only.
Please note that this series does not address Al's comment [2]. In SCTP,
some sysctl knobs set other sysfs-exposed variables for the min/max: two
processes could then write two linked values at the same time, resulting
in new values being outside the new boundaries. It would be great if
SCTP developers can look at this problem.
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Link: https://lore.kernel.org/20250105211158.GL1977892@ZenIV [2]
====================
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-0-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The per-netns structure can be obtained from the table->data using
container_of(), then the 'net' one can be retrieved from the listen
socket (if available).
Fixes: c6a58ffed5 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-9-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.probe_interval' is
used.
Fixes: d1e462a7a5 ("sctp: add probe_interval in sysctl and sock/asoc/transport")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-8-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
Fixes: 046c052b47 ("sctp: enable udp tunneling socks")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-7-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, but that would
increase the size of this fix, while 'sctp.ctl_sock' still needs to be
retrieved from 'net' structure.
Fixes: b14878ccb7 ("net: sctp: cache auth_enable per endpoint")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-6-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.rto_min/max' is used.
Fixes: 4f3fdf3bc5 ("sctp: add check rto_min and rto_max in sysctl")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-5-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in a previous commit of this series, using the 'net'
structure via 'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'net' structure can be obtained from the table->data using
container_of().
Note that table->data could also be used directly, as this is the only
member needed from the 'net' structure, but that would increase the size
of this fix, to use '*data' everywhere 'net->sctp.sctp_hmac_alg' is
used.
Fixes: 3c68198e75 ("sctp: Make hmac algorithm selection for cookie generation dynamic")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-4-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As mentioned in the previous commit, using the 'net' structure via
'current' is not recommended for different reasons:
- Inconsistency: getting info from the reader's/writer's netns vs only
from the opener's netns.
- current->nsproxy can be NULL in some cases, resulting in an 'Oops'
(null-ptr-deref), e.g. when the current task is exiting, as spotted by
syzbot [1] using acct(2).
The 'pernet' structure can be obtained from the table->data using
container_of().
Fixes: 27069e7cb3 ("mptcp: disable active MPTCP in case of blackhole")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/67769ecb.050a0220.3a8527.003f.GAE@google.com [1]
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-3-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'net.mptcp.available_schedulers' sysctl knob is there to list available
schedulers, not to modify this list.
There are then no reasons to give write access to it.
Nothing would have been written anyway, but no errors would have been
returned, which is unexpected.
Fixes: 73c900aa36 ("mptcp: add net.mptcp.available_schedulers")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250108-net-sysctl-current-nsproxy-v1-1-5df34b2083e8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, the regulator core resolved its supply only from the parent
device or its children, ignoring the of_node specified in the
regulator_config structure.
This behavior causes issues in scenarios where multiple regulator devices
are registered for components described as children of a controller, each
with their own specific regulator supply.
For instance, in a PSE controller with multiple PIs (Power Interfaces),
each PI may have a distinct regulator supply. However, the regulator core
would incorrectly use the PSE controller node or its first child to look up
the regulator supply, rather than the node specified by the
regulator_config->of_node for the PI.
This update modifies the behavior to prioritize the of_node in
regulator_config for resolving the supply. This ensures correct resolution
of the power supply for each device. If no supply is found in the provided
of_node, the core falls back to searching within the parent device as
before.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250109-b4-feature_poe_arrange-v2-13-55ded947b510@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
ASoC framwork has disable_route_checks flag. Intel is the last user of it,
but it seems it exists in dead code. So we can remove it.