commit d13b6a128a upstream.
When some wake IRQs are disabled in the device tree, the corresponding
interrupt entries are removed from DT. In such cases, the driver
currently calls platform_get_irq(), which returns -ENXIO and logs
an error like:
tegra-xusb 3610000.usb: error -ENXIO: IRQ index 2 not found
However, not all wake IRQs are mandatory. The hardware can operate
normally even if some wake sources are not defined in DT. To avoid this
false alarm and allow missing wake IRQs gracefully, use
platform_get_irq_optional() instead of platform_get_irq().
Fixes: 5df186e2ef ("usb: xhci: tegra: Support USB wakeup function for Tegra234")
Cc: stable <stable@kernel.org>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Wei-Cheng Chen <weichengc@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/20260112145653.95691-1-weichengc@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b246caa680 upstream.
The USB2 Bias Pad Control register manages analog parameters for signal
detection. Previously, the HS_DISCON_LEVEL relied on hardware reset
values, which may lead to the detection failure.
Explicitly configure HS_DISCON_LEVEL to 0x7. This ensures the disconnect
threshold is sufficient to guarantee reliable detection.
Fixes: bbf711682c ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://patch.msgid.link/20251212032116.768307-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49ccab4bed upstream.
Currently, the PHY only registers the typec orientation switch when it
is built in. If the typec driver is built as a module, the switch
registration is skipped due to the preprocessor condition, causing
orientation detection to fail.
With commit
45fe729be9 ("usb: typec: Stub out typec_switch APIs when CONFIG_TYPEC=n")
the preprocessor condition is not needed anymore and the orientation
switch is correctly registered for both built-in and module builds.
Fixes: b58f0f86fd ("phy: fsl-imx8mq-usb: add tca function driver for imx95")
Cc: stable@vger.kernel.org
Suggested-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://patch.msgid.link/20251126140136.1202241-1-fra.schnyder@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028e8ca7b2 upstream.
When the OTG USB port is used to power the SoC, configured as peripheral
and used in gadget mode, there is a disconnection about 6 seconds after the
gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The problem happens because of the PHY driver code flow, summarized as:
* UDC start code (triggered via configfs at any time after boot)
-> phy_init
-> rockchip_usb2phy_init
-> schedule_delayed_work(otg_sm_work [A], 6 sec)
-> phy_power_on
-> rockchip_usb2phy_power_on
-> enable clock
-> rockchip_usb2phy_reset
* Now the gadget interface is up and running.
* 6 seconds later otg_sm_work starts [A]
-> rockchip_usb2phy_otg_sm_work():
if (B_IDLE state && VBUS present && ...):
schedule_delayed_work(&rport->chg_work [B], 0);
* immediately the chg_detect_work starts [B]
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
if (!rport->suspended):
rockchip_usb2phy_power_off() <--- [X]
At [X], the PHY is powered off, causing a disconnection. This quickly
triggers a new connection and following re-enumeration, but any connection
that had been established during the 6 seconds is broken.
The code already checks for !rport->suspended (which, somewhat
counter-intuitively, means the PHY is powered on), so add a guard for VBUS
as well to avoid a disconnection when a cable is connected.
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Co-developed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-1-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2ec4723de upstream.
After U-Boot initializes PCIe with "pcie enum", Linux fails to detect
an NVMe disk on some boot cycles with:
phy phy-32f00000.pcie-phy.0: phy poweron failed --> -110
Discussion with NXP identified that the iMX8MP PCIe PHY PLL may fail to
lock when re-initialized without a reset cycle [1].
The issue reproduces on 7% of tested hardware platforms, with a 30-40%
failure rate per affected device across boot cycles.
Insert a reset cycle in the power-on routine to ensure the PHY is
initialized from a known state.
[1] https://community.nxp.com/t5/i-MX-Processors/iMX8MP-PCIe-initialization-in-U-Boot/m-p/2248437#M242401
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251223150254.1075221-1-rafael@beims.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e07dea3de5 upstream.
The for_each_available_child_of_node() calls of_node_put() to
release child_np in each success loop. After breaking from the
loop with the child_np has been released, the code will jump to
the put_child label and will call the of_node_put() again if the
devm_request_threaded_irq() fails. These cause a double free bug.
Fix by returning directly to avoid the duplicate of_node_put().
Fixes: ed2b5a8e6b ("phy: phy-rockchip-inno-usb2: support muxed interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260109154626.2452034-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4914d67da9 upstream.
The mmio regmap that may be allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind.
Fixes: 5ab90f4012 ("phy: ti: gmii-sel: Do not use syscon helper to build regmap")
Cc: stable@vger.kernel.org # 6.14
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20251127134834.2030-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d8f725b79 upstream.
When the OTG USB port is used to power to SoC, configured as peripheral and
used in gadget mode, communication stops without notice about 6 seconds
after the gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The related code flow in the PHY driver code can be summarized as:
* the first time chg_detect_work starts (6 seconds after gadget is
configured and enumerated)
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, false); [Y]
* rockchip_chg_detect_work() changes state and re-triggers itself a few
times until it reaches the DETECTED state:
-> rockchip_chg_detect_work():
if chg_state is DETECTED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, true); [Z]
At [Y] all existing communications stop. E.g. using a CDC serial gadget,
the /dev/tty* devices are still present on both host and device, but no
data is transferred anymore. The later call with a 'true' argument at [Z]
does not restore it.
Due to the lack of documentation, what chg_det.opmode does exactly is not
clear, however by code inspection it seems reasonable that is disables
something needed to keep the communication working, and testing proves that
disabling these lines lets gadget mode keep working. So prevent changes to
chg_det.opmode when there is a cable connected (VBUS present).
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-2-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 269031b15c upstream.
Commit 7ffb791423 ("x86/kaslr: Reduce KASLR entropy on most x86 systems")
is too narrow. The effect being mitigated in that commit is caused by
ZONE_DEVICE which PCI_P2PDMA has a dependency. ZONE_DEVICE, in general,
lets any physical address be added to the direct-map. I.e. not only ACPI
hotplug ranges, CXL Memory Windows, or EFI Specific Purpose Memory, but
also any PCI MMIO range for the DEVICE_PRIVATE and PCI_P2PDMA cases. Update
the mitigation, limit KASLR entropy, to apply in all ZONE_DEVICE=y cases.
Distro kernels typically have PCI_P2PDMA=y, so the practical exposure of
this problem is limited to the PCI_P2PDMA=n case.
A potential path to recover entropy would be to walk ACPI and determine the
limits for hotplug and PCI MMIO before kernel_randomize_memory(). On
smaller systems that could yield some KASLR address bits. This needs
additional investigation to determine if some limited ACPI table scanning
can happen this early without an open coded solution like
arch/x86/boot/compressed/acpi.c needs to deploy.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <kees@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Fixes: 7ffb791423 ("x86/kaslr: Reduce KASLR entropy on most x86 systems")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Balbir Singh <balbirs@nvidia.com>
Tested-by: Yasunori Goto <y-goto@fujitsu.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: http://patch.msgid.link/692e08b2516d4_261c1100a3@dwillia2-mobl4.notmuch
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 777a8560fd upstream.
Prevent a "BUG: unable to handle kernel NULL pointer dereference in
filemap_read_folio".
For the sleepable context, convert freader to use __kernel_read() instead
of direct page cache access via read_cache_folio(). This simplifies the
faultable code path by using the standard kernel file reading interface
which handles all the complexity of reading file data.
At the moment we are not changing the code for non-sleepable context which
uses filemap_get_folio() and only succeeds if the target folios are
already in memory and up-to-date. The reason is to keep the patch simple
and easier to backport to stable kernels.
Syzbot repro does not crash the kernel anymore and the selftests run
successfully.
In the follow up we will make __kernel_read() with IOCB_NOWAIT work for
non-sleepable contexts. In addition, I would like to replace the
secretmem check with a more generic approach and will add fstest for the
buildid code.
Link: https://lkml.kernel.org/r/20251222205859.3968077-1-shakeel.butt@linux.dev
Fixes: ad41251c29 ("lib/buildid: implement sleepable build_id_parse() API")
Reported-by: syzbot+09b7d050e4806540153d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=09b7d050e4806540153d
Signed-off-by: Shakeel Butt <shakeel.butt@linux.dev>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Jinchao Wang <wangjinchao600@gmail.com>
Link: https://lkml.kernel.org/r/aUteBPWPYzVWIZFH@ndev
Reviewed-by: Christian Brauner <brauner@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Daniel Borkman <daniel@iogearbox.net>
Cc: "Darrick J. Wong" <djwong@kernel.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcdef3bcbb upstream.
When we fail to refill the receive buffers, we schedule a delayed worker
to retry later. However, this worker creates some concurrency issues.
For example, when the worker runs concurrently with virtnet_xdp_set,
both need to temporarily disable queue's NAPI before enabling again.
Without proper synchronization, a deadlock can happen when
napi_disable() is called on an already disabled NAPI. That
napi_disable() call will be stuck and so will the subsequent
napi_enable() call.
To simplify the logic and avoid further problems, we will instead retry
refilling in the next NAPI poll.
Fixes: 4bc12818b3 ("virtio-net: disable delayed refill when pausing rx")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Closes: https://lore.kernel.org/526b5396-459d-4d02-8635-a222d07b46d7@redhat.com
Cc: stable@vger.kernel.org
Suggested-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20260106150438.7425-2-minhquangbui99@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b2d155366 upstream.
xfs_rtcopy_summary() should return the appropriate error code
instead of always returning 0. The caller of this function which is
xfs_growfs_rt_bmblock() is already handling the error.
Fixes: e94b53ff69 ("xfs: cache last bitmap block in realtime allocator")
Signed-off-by: Nirjhar Roy (IBM) <nirjhar.roy.lists@gmail.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # v6.7
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c360004c01 upstream.
Sparse inode cluster allocation sets min/max agbno values to avoid
allocating an inode cluster that might map to an invalid inode
chunk. For example, we can't have an inode record mapped to agbno 0
or that extends past the end of a runt AG of misaligned size.
The initial calculation of max_agbno is unnecessarily conservative,
however. This has triggered a corner case allocation failure where a
small runt AG (i.e. 2063 blocks) is mostly full save for an extent
to the EOFS boundary: [2050,13]. max_agbno is set to 2048 in this
case, which happens to be the offset of the last possible valid
inode chunk in the AG. In practice, we should be able to allocate
the 4-block cluster at agbno 2052 to map to the parent inode record
at agbno 2048, but the max_agbno value precludes it.
Note that this can result in filesystem shutdown via dirty trans
cancel on stable kernels prior to commit 9eb775968b ("xfs: walk
all AGs if TRYLOCK passed to xfs_alloc_vextent_iterate_ags") because
the tail AG selection by the allocator sets t_highest_agno on the
transaction. If the inode allocator spins around and finds an inode
chunk with free inodes in an earlier AG, the subsequent dir name
creation path may still fail to allocate due to the AG restriction
and cancel.
To avoid this problem, update the max_agbno calculation to the agbno
prior to the last chunk aligned agbno in the AG. This is not
necessarily the last valid allocation target for a sparse chunk, but
since inode chunks (i.e. records) are chunk aligned and sparse
allocs are cluster sized/aligned, this allows the sb_spino_align
alignment restriction to take over and round down the max effective
agbno to within the last valid inode chunk in the AG.
Note that even though the allocator improvements in the
aforementioned commit seem to avoid this particular dirty trans
cancel situation, the max_agbno logic improvement still applies as
we should be able to allocate from an AG that has been appropriately
selected. The more important target for this patch however are
older/stable kernels prior to this allocator rework/improvement.
Cc: stable@vger.kernel.org # v4.2
Fixes: 56d1115c9b ("xfs: allocate sparse inode chunks on full chunk allocation failure")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be55257fab upstream.
The pg_remaining calculation in ftrace_process_locs() assumes that
ENTRIES_PER_PAGE multiplied by 2^order equals the actual capacity of the
allocated page group. However, ENTRIES_PER_PAGE is PAGE_SIZE / ENTRY_SIZE
(integer division). When PAGE_SIZE is not a multiple of ENTRY_SIZE (e.g.
4096 / 24 = 170 with remainder 16), high-order allocations (like 256 pages)
have significantly more capacity than 256 * 170. This leads to pg_remaining
being underestimated, which in turn makes skip (derived from skipped -
pg_remaining) larger than expected, causing the WARN(skip != remaining)
to trigger.
Extra allocated pages for ftrace: 2 with 654 skipped
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:7295 ftrace_process_locs+0x5bf/0x5e0
A similar problem in ftrace_allocate_records() can result in allocating
too many pages. This can trigger the second warning in
ftrace_process_locs().
Extra allocated pages for ftrace
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:7276 ftrace_process_locs+0x548/0x580
Use the actual capacity of a page group to determine the number of pages
to allocate. Have ftrace_allocate_pages() return the number of allocated
pages to avoid having to calculate it. Use the actual page group capacity
when validating the number of unused pages due to skipped entries.
Drop the definition of ENTRIES_PER_PAGE since it is no longer used.
Cc: stable@vger.kernel.org
Fixes: 4a3efc6baf ("ftrace: Update the mcount_loc check of skipped entries")
Link: https://patch.msgid.link/20260113152243.3557219-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21c68ad1d9 upstream.
Commit 66bce7afba ("selftests/mm: fix test result reporting in
gup_longterm") introduced a small bug causing unknown filesystems to
always result in a test failure.
This is because do_test() was updated to use a common reporting path, but
this case appears to have been missed.
This is problematic for e.g. virtme-ng which uses an overlayfs file
system, causing gup_longterm to appear to fail each time due to a test
count mismatch:
# Planned tests != run tests (50 != 46)
# Totals: pass:24 fail:0 xfail:0 xpass:0 skip:22 error:0
The fix is to simply change the return into a break.
Link: https://lkml.kernel.org/r/20260106154547.214907-1-lorenzo.stoakes@oracle.com
Fixes: 66bce7afba ("selftests/mm: fix test result reporting in gup_longterm")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: David Hildenbrand (Red Hat) <david@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: "Liam R. Howlett" <Liam.Howlett@oracle.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Peter Xu <peterx@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb39444732 upstream.
Now we correctly handle forked faulted/unfaulted merge on mremap(),
exhaustively assert that we handle this correctly.
Do this in the less duplicative way by adding a new merge_with_fork
fixture and forked/unforked variants, and abstract the forking logic as
necessary to avoid code duplication with this also.
Link: https://lkml.kernel.org/r/1daf76d89fdb9d96f38a6a0152d8f3c2e9e30ac7.1767638272.git.lorenzo.stoakes@oracle.com
Fixes: 879bca0a2c ("mm/vma: fix incorrectly disallowed anonymous VMA merges")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: David Hildenbrand (Red Hat) <david@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jeongjun Park <aha310510@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Pedro Falcato <pfalcato@suse.de>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yeoreum Yun <yeoreum.yun@arm.com>
Cc: Harry Yoo <harry.yoo@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ace8f2db6 upstream.
Test that mremap()'ing a VMA into a position such that the target VMA on
merge is unfaulted and the source faulted is correctly performed.
We cover 4 cases:
1. Previous VMA unfaulted:
copied -----|
v
|-----------|.............|
| unfaulted |(faulted VMA)|
|-----------|.............|
prev
target = prev, expand prev to cover.
2. Next VMA unfaulted:
copied -----|
v
|.............|-----------|
|(faulted VMA)| unfaulted |
|.............|-----------|
next
target = next, expand next to cover.
3. Both adjacent VMAs unfaulted:
copied -----|
v
|-----------|.............|-----------|
| unfaulted |(faulted VMA)| unfaulted |
|-----------|.............|-----------|
prev next
target = prev, expand prev to cover.
4. prev unfaulted, next faulted:
copied -----|
v
|-----------|.............|-----------|
| unfaulted |(faulted VMA)| faulted |
|-----------|.............|-----------|
prev next
target = prev, expand prev to cover. Essentially equivalent to 3, but
with additional requirement that next's anon_vma is the same as the
copied VMA's.
Each of these are performed with MREMAP_DONTUNMAP set, which will cause a
KASAN assert for UAF or an assert on zero refcount anon_vma if a bug
exists with correctly propagating anon_vma state in each scenario.
Link: https://lkml.kernel.org/r/f903af2930c7c2c6e0948c886b58d0f42d8e8ba3.1767638272.git.lorenzo.stoakes@oracle.com
Fixes: 879bca0a2c ("mm/vma: fix incorrectly disallowed anonymous VMA merges")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: David Hildenbrand (Red Hat) <david@kernel.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jeongjun Park <aha310510@gmail.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Pedro Falcato <pfalcato@suse.de>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yeoreum Yun <yeoreum.yun@arm.com>
Cc: Harry Yoo <harry.yoo@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1809c82aa0 upstream.
Since j1939_session_deactivate_activate_next() in j1939_tp_rxtimer() is
called only when the timer is enabled, we need to call
j1939_session_deactivate_activate_next() if we cancelled the timer.
Otherwise, refcount for j1939_session leaks, which will later appear as
| unregister_netdevice: waiting for vcan0 to become free. Usage count = 2.
problem.
Reported-by: syzbot <syzbot+881d65229ca4f9ae8c84@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=881d65229ca4f9ae8c84
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://patch.msgid.link/b1212653-8fa1-44e1-be9d-12f950fb3a07@I-love.SAKURA.ne.jp
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e707c591a1 upstream.
The Secondary Sample Point Source field has been
set to an incorrect value by some mistake in the
past
0b01 - SSP_SRC_NO_SSP - SSP is not used.
for data bitrates above 1 MBit/s. The correct/default
value already used for lower bitrates is
0b00 - SSP_SRC_MEAS_N_OFFSET - SSP position = TRV_DELAY
(Measured Transmitter delay) + SSP_OFFSET.
The related configuration register structure is described
in section 3.1.46 SSP_CFG of the CTU CAN FD
IP CORE Datasheet.
The analysis leading to the proper configuration
is described in section 2.8.3 Secondary sampling point
of the datasheet.
The change has been tested on AMD/Xilinx Zynq
with the next CTU CN FD IP core versions:
- 2.6 aka master in the "integration with Zynq-7000 system" test
6.12.43-rt12+ #1 SMP PREEMPT_RT kernel with CTU CAN FD git
driver (change already included in the driver repo)
- older 2.5 snapshot with mainline kernels with this patch
applied locally in the multiple CAN latency tester nightly runs
6.18.0-rc4-rt3-dut #1 SMP PREEMPT_RT
6.19.0-rc3-dut
The logs, the datasheet and sources are available at
https://canbus.pages.fel.cvut.cz/
Signed-off-by: Ondrej Ille <ondrej.ille@gmail.com>
Signed-off-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20260105111620.16580-1-pisa@fel.cvut.cz
Fixes: 2dcb8e8782 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7352e1d593 upstream.
In gs_can_open(), the URBs for USB-in transfers are allocated, added to the
parent->rx_submitted anchor and submitted. In the complete callback
gs_usb_receive_bulk_callback(), the URB is processed and resubmitted. In
gs_can_close() the URBs are freed by calling
usb_kill_anchored_urbs(parent->rx_submitted).
However, this does not take into account that the USB framework unanchors
the URB before the complete function is called. This means that once an
in-URB has been completed, it is no longer anchored and is ultimately not
released in gs_can_close().
Fix the memory leak by anchoring the URB in the
gs_usb_receive_bulk_callback() to the parent->rx_submitted anchor.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260105-gs_usb-fix-memory-leak-v2-1-cc6ed6438034@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40b94ec7ed upstream.
When CONFIG_BLK_DEV_NULL_BLK_FAULT_INJECTION is enabled, the null-blk
driver sets up fault injection support by creating the timeout_inject,
requeue_inject, and init_hctx_fault_inject configfs items as children
of the top-level nullbX configfs group.
However, when the nullbX device is removed, the references taken to
these fault-config configfs items are not released. As a result,
kmemleak reports a memory leak, for example:
unreferenced object 0xc00000021ff25c40 (size 32):
comm "mkdir", pid 10665, jiffies 4322121578
hex dump (first 32 bytes):
69 6e 69 74 5f 68 63 74 78 5f 66 61 75 6c 74 5f init_hctx_fault_
69 6e 6a 65 63 74 00 88 00 00 00 00 00 00 00 00 inject..........
backtrace (crc 1a018c86):
__kmalloc_node_track_caller_noprof+0x494/0xbd8
kvasprintf+0x74/0xf4
config_item_set_name+0xf0/0x104
config_group_init_type_name+0x48/0xfc
fault_config_init+0x48/0xf0
0xc0080000180559e4
configfs_mkdir+0x304/0x814
vfs_mkdir+0x49c/0x604
do_mkdirat+0x314/0x3d0
sys_mkdir+0xa0/0xd8
system_call_exception+0x1b0/0x4f0
system_call_vectored_common+0x15c/0x2ec
Fix this by explicitly releasing the references to the fault-config
configfs items when dropping the reference to the top-level nullbX
configfs group.
Cc: stable@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Fixes: bb4c19e030 ("block: null_blk: make fault-injection dynamically configurable per device")
Signed-off-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0383a8edef upstream.
The host is allowed to set FPU state that includes a disabled
xstate component. Check that this does not cause bad effects.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1025dcd37 upstream.
Rework the guest=>host syncs in the AMX test to use named actions instead
of arbitrary, incrementing numbers. The "stage" of the test has no real
meaning, what matters is what action the test wants the host to perform.
The incrementing numbers are somewhat helpful for triaging failures, but
fully debugging failures almost always requires a much deeper dive into
the test (and KVM).
Using named actions not only makes it easier to extend the test without
having to shift all sync point numbers, it makes the code easier to read.
[Commit message by Sean Christopherson]
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a49157dee upstream.
Some low-level drivers (LLD) access block layer crypto fields, such as
rq->crypt_keyslot and rq->crypt_ctx within `struct request`, to
configure hardware for inline encryption. However, SCSI Error Handling
(EH) commands (e.g., TEST UNIT READY, START STOP UNIT) should not
involve any encryption setup.
To prevent drivers from erroneously applying crypto settings during EH,
this patch saves the original values of rq->crypt_keyslot and
rq->crypt_ctx before an EH command is prepared via scsi_eh_prep_cmnd().
These fields in the 'struct request' are then set to NULL. The original
values are restored in scsi_eh_restore_cmnd() after the EH command
completes.
This ensures that the block layer crypto context does not leak into EH
command execution.
Signed-off-by: Brian Kao <powenkao@google.com>
Link: https://patch.msgid.link/20251218031726.2642834-1-powenkao@google.com
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f28beb69c5 upstream.
Some faulty devices (ZWO EFWmini) have a wrong optional HID class
descriptor count compared to the provided length.
Given that we plainly ignore those optional descriptor, we can attempt
to fix the provided number so we do not lock out those devices.
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e008ec6c79 ]
While FIFO/RR have static priority, DEADLINE is a dynamic priority
scheme. Notably it has static priority -1. Do not assume the priority
doesn't change for deadline tasks just because the static priority
doesn't change.
This ensures DL always sees {DE,EN}QUEUE_MOVE where appropriate.
Fixes: ff77e46853 ("sched/rt: Fix PI handling vs. sched_setscheduler()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Pierre Gondois <pierre.gondois@arm.com>
Tested-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://patch.msgid.link/20260114130528.GB831285@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4de9ff7606 ]
When setup_new_dl_entity() is called from enqueue_task_dl() ->
enqueue_dl_entity(), the rq-clock should already be updated, and
calling update_rq_clock() again is not right.
Move the update_rq_clock() to the one other caller of
setup_new_dl_entity(): sched_init_dl_server().
Fixes: 9f239df555 ("sched/deadline: Initialize dl_servers after SMP")
Reported-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Pierre Gondois <pierre.gondois@arm.com>
Link: https://patch.msgid.link/20260113115622.GA831285@noisy.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a3f51365 ]
EDMA resumes early and suspends late in the system power transition
sequence, while LPI2C enters the NOIRQ stage for both suspend and resume.
This means LPI2C resources become available before EDMA is fully resumed.
Once IRQs are enabled, a slave device may immediately trigger an LPI2C
transfer. If the transfer length meets DMA requirements, the driver will
attempt to use EDMA even though EDMA may still be unavailable.
This timing gap can lead to transfer failures. To prevent this, force
LPI2C to use PIO mode during system-wide suspend and resume transitions.
This reduces dependency on EDMA and avoids using an unready DMA resource.
Fixes: a09c8b3f90 ("i2c: imx-lpi2c: add eDMA mode support for LPI2C")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0c50e3743 ]
The I2C Hub controller is a simpler GENI I2C variant that doesn't
support DMA at all, add a no_dma flag to make sure it nevers selects
the SE DMA mode with mappable 32bytes long transfers.
Fixes: cacd9643ec ("i2c: qcom-geni: add support for I2C Master Hub variant")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Mukesh Kumar Savaliya <mukesh.savaliya@oss.qualcomm.com>>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12d4fd9a65 ]
ida_alloc_max() interprets its max argument as inclusive.
Using SDW_FW_MAX_DEVICES(16) therefore allows an ID of 16 to be
allocated, but the IRQ domain created for the bus is sized for IDs
0-15. If 16 is returned, irq_create_mapping() fails and the driver
ends up with an invalid IRQ mapping.
Limit the allocation to 0-15 by passing SDW_FW_MAX_DEVICES - 1.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202512240450.hlDH3nCs-lkp@intel.com/
Fixes: aab12022b0 ("soundwire: bus: Add internal slave ID and use for IRQs")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260110201959.2523024-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e1136acf8 ]
The dma_pool created by dma_pool_create() is not destroyed when
dma_async_device_register() or of_dma_controller_register() fails,
causing a resource leak in the probe error paths.
Add dma_pool_destroy() in both error paths to properly release the
allocated dma_pool resource.
Fixes: 7bedaa5537 ("dmaengine: add OMAP DMA engine driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://patch.msgid.link/20251103073018.643-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb21116099 ]
"family" is an enum, thus cast of pointer on 64-bit compile test with
clang W=1 causes:
phy-bcm-ns-usb3.c:206:17: error: cast to smaller integer type 'enum bcm_ns_family' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
This was already fixed in commit bd6e74a2f0 ("phy: broadcom: ns-usb3:
fix Wvoid-pointer-to-enum-cast warning") but then got bad in commit
21bf6fc47a ("phy: Use device_get_match_data()").
Note that after various discussions the preferred cast is via "unsigned
long", not "uintptr_t".
Fixes: 21bf6fc47a ("phy: Use device_get_match_data()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251224115533.154162-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29fbfa46e4 ]
I think, based on my best understanding, that this type is likely a typo
(even though in the end both are u16)
Signed-off-by: Tingmao Wang <m@maowtm.org>
Fixes: 2fc80c69df ("landlock: Log file-related denials")
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/7339ad7b47f998affd84ca629a334a71f913616d.1765040503.git.m@maowtm.org
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1a57c3359 ]
Remove bind() call on a client socket that doesn't make sense.
Since strlen(cli_un.sun_path) returns a random value depending on stack
garbage, that many uninitialized bytes are read from the stack as an
unix socket address. This creates random test failures due to the bind
address being invalid or already in use if the same stack value comes up
twice.
Fixes: f83d51a5bd ("selftests/landlock: Check IOCTL restrictions for named UNIX domain sockets")
Signed-off-by: Matthieu Buffet <matthieu@buffet.re>
Reviewed-by: Günther Noack <gnoack@google.com>
Link: https://lore.kernel.org/r/20251201003631.190817-1-matthieu@buffet.re
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd09d9a05c ]
The nominal error code for bind(AF_UNSPEC) on an IPv6 socket
is -EAFNOSUPPORT, not -EINVAL. -EINVAL is only returned when
the supplied address struct is too short, which happens to be
the case in current selftests because they treat AF_UNSPEC
like IPv4 sockets do: as an alias for AF_INET (which is a
16-byte struct instead of the 24 bytes required by IPv6
sockets).
Make the union large enough for any address (by adding struct
sockaddr_storage to the union), and make AF_UNSPEC addresses
large enough for any family.
Test for -EAFNOSUPPORT instead, and add a dedicated test case
for truncated inputs with -EINVAL.
Fixes: a549d055a2 ("selftests/landlock: Add network tests")
Signed-off-by: Matthieu Buffet <matthieu@buffet.re>
Link: https://lore.kernel.org/r/20251027190726.626244-2-matthieu@buffet.re
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4d82cbce2 ]
current_check_access_socket() treats AF_UNSPEC addresses as
AF_INET ones, and only later adds special case handling to
allow connect(AF_UNSPEC), and on IPv4 sockets
bind(AF_UNSPEC+INADDR_ANY).
This would be fine except AF_UNSPEC addresses can be as
short as a bare AF_UNSPEC sa_family_t field, and nothing
more. The AF_INET code path incorrectly enforces a length of
sizeof(struct sockaddr_in) instead.
Move AF_UNSPEC edge case handling up inside the switch-case,
before the address is (potentially incorrectly) treated as
AF_INET.
Fixes: fff69fb03d ("landlock: Support network rules with TCP bind and connect")
Signed-off-by: Matthieu Buffet <matthieu@buffet.re>
Link: https://lore.kernel.org/r/20251027190726.626244-4-matthieu@buffet.re
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08aa19de72 ]
devm_pm_runtime_enable() can fail due to memory allocation. The current
code ignores its return value after calling pm_runtime_set_active(),
leaving the device in an inconsistent state if runtime PM initialization
fails.
Check the return value of devm_pm_runtime_enable() and return on
failure. Also move the declaration of 'ret' to the function scope
to support this check.
Fixes: ee8e41b504 ("phy: ti: phy-da8xx-usb: Add runtime PM support")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251124105734.1027-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabd25b572 ]
The "index" variable is used as an index into the usbphyc->phys[] array
which has usbphyc->nphys elements. So if it is equal to usbphyc->nphys
then it is one element out of bounds. The "index" comes from the
device tree so it's data that we trust and it's unlikely to be wrong,
however it's obviously still worth fixing the bug. Change the > to >=.
Fixes: 94c358da3a ("phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://patch.msgid.link/aTfHcMJK1wFVnvEe@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ca52c0983 ]
Enabling runtime PM before attaching the QPHY instance as driver data
can lead to a NULL pointer dereference in runtime PM callbacks that
expect valid driver data. There is a small window where the suspend
callback may run after PM runtime enabling and before runtime forbid.
This causes a sporadic crash during boot:
```
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a1
[...]
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.7+ #116 PREEMPT
Workqueue: pm pm_runtime_work
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : qusb2_phy_runtime_suspend+0x14/0x1e0 [phy_qcom_qusb2]
lr : pm_generic_runtime_suspend+0x2c/0x44
[...]
```
Attach the QPHY instance as driver data before enabling runtime PM to
prevent NULL pointer dereference in runtime PM callbacks.
Reorder pm_runtime_enable() and pm_runtime_forbid() to prevent a
short window where an unnecessary runtime suspend can occur.
Use the devres-managed version to ensure PM runtime is symmetrically
disabled during driver removal for proper cleanup.
Fixes: 891a96f65a ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20251219085640.114473-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8becf9179a ]
Clear the PCS_TX_SWING_FULL field mask before setting the new value
in PHY_CTRL5 register. Without clearing the mask first, the OR operation
could leave previously set bits, resulting in incorrect register
configuration.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Suggested-by: Leonid Segal <leonids@variscite.com>
Acked-by: Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://patch.msgid.link/20251219160912.561431-1-stefano.r@variscite.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0732fe787 ]
When device tree lacks optional "xlnx,addrwidth" property, the addr_width
variable remained uninitialized with garbage values, causing incorrect
DMA mask configuration and subsequent probe failure. The fix ensures a
fallback to the default 32-bit address width when this property is missing.
Signed-off-by: Suraj Gupta <suraj.gupta2@amd.com>
Fixes: b72db4005f ("dmaengine: vdma: Add 64 bit addressing support to the driver")
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Folker Schwesinger <dev@folker-schwesinger.de>
Link: https://patch.msgid.link/20251021183006.3434495-1-suraj.gupta2@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2efd07a7c3 ]
A use-after-free bug exists in the Tegra ADMA driver when audio streams
are terminated, particularly during XRUN conditions. The issue occurs
when the DMA buffer is freed by tegra_adma_terminate_all() before the
vchan completion tasklet finishes accessing it.
The race condition follows this sequence:
1. DMA transfer completes, triggering an interrupt that schedules the
completion tasklet (tasklet has not executed yet)
2. Audio playback stops, calling tegra_adma_terminate_all() which
frees the DMA buffer memory via kfree()
3. The scheduled tasklet finally executes, calling vchan_complete()
which attempts to access the already-freed memory
Since tasklets can execute at any time after being scheduled, there is
no guarantee that the buffer will remain valid when vchan_complete()
runs.
Fix this by properly synchronizing the virtual channel completion:
- Calling vchan_terminate_vdesc() in tegra_adma_stop() to mark the
descriptors as terminated instead of freeing the descriptor.
- Add the callback tegra_adma_synchronize() that calls
vchan_synchronize() which kills any pending tasklets and frees any
terminated descriptors.
Crash logs:
[ 337.427523] BUG: KASAN: use-after-free in vchan_complete+0x124/0x3b0
[ 337.427544] Read of size 8 at addr ffff000132055428 by task swapper/0/0
[ 337.427562] Call trace:
[ 337.427564] dump_backtrace+0x0/0x320
[ 337.427571] show_stack+0x20/0x30
[ 337.427575] dump_stack_lvl+0x68/0x84
[ 337.427584] print_address_description.constprop.0+0x74/0x2b8
[ 337.427590] kasan_report+0x1f4/0x210
[ 337.427598] __asan_load8+0xa0/0xd0
[ 337.427603] vchan_complete+0x124/0x3b0
[ 337.427609] tasklet_action_common.constprop.0+0x190/0x1d0
[ 337.427617] tasklet_action+0x30/0x40
[ 337.427623] __do_softirq+0x1a0/0x5c4
[ 337.427628] irq_exit+0x110/0x140
[ 337.427633] handle_domain_irq+0xa4/0xe0
[ 337.427640] gic_handle_irq+0x64/0x160
[ 337.427644] call_on_irq_stack+0x20/0x4c
[ 337.427649] do_interrupt_handler+0x7c/0x90
[ 337.427654] el1_interrupt+0x30/0x80
[ 337.427659] el1h_64_irq_handler+0x18/0x30
[ 337.427663] el1h_64_irq+0x7c/0x80
[ 337.427667] cpuidle_enter_state+0xe4/0x540
[ 337.427674] cpuidle_enter+0x54/0x80
[ 337.427679] do_idle+0x2e0/0x380
[ 337.427685] cpu_startup_entry+0x2c/0x70
[ 337.427690] rest_init+0x114/0x130
[ 337.427695] arch_call_rest_init+0x18/0x24
[ 337.427702] start_kernel+0x380/0x3b4
[ 337.427706] __primary_switched+0xc0/0xc8
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sheetal <sheetal@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/20251110142445.3842036-1-sheetal@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7d436a6c1 ]
The max_register field is assigned the size of the register memory
region instead of the offset of the last register.
The result is that reading from the regmap via debugfs can cause
a segmentation fault:
tail /sys/kernel/debug/regmap/xdma.1.auto/registers
Unable to handle kernel paging request at virtual address ffff800082f70000
Mem abort info:
ESR = 0x0000000096000007
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x07: level 3 translation fault
[...]
Call trace:
regmap_mmio_read32le+0x10/0x30
_regmap_bus_reg_read+0x74/0xc0
_regmap_read+0x68/0x198
regmap_read+0x54/0x88
regmap_read_debugfs+0x140/0x380
regmap_map_read_file+0x30/0x48
full_proxy_read+0x68/0xc8
vfs_read+0xcc/0x310
ksys_read+0x7c/0x120
__arm64_sys_read+0x24/0x40
invoke_syscall.constprop.0+0x64/0x108
do_el0_svc+0xb0/0xd8
el0_svc+0x38/0x130
el0t_64_sync_handler+0x120/0x138
el0t_64_sync+0x194/0x198
Code: aa1e03e9 d503201f f9400000 8b214000 (b9400000)
---[ end trace 0000000000000000 ]---
note: tail[1217] exited with irqs disabled
note: tail[1217] exited with preempt_count 1
Segmentation fault
Fixes: 17ce252266 ("dmaengine: xilinx: xdma: Add xilinx xdma driver")
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49400b701e ]
The driver's existing logic for setting the DMA mask for "marvell,pdma-1.0"
was flawed. It incorrectly relied on pdev->dev->coherent_dma_mask instead
of declaring the hardware's fixed addressing capability. A cleaner and
more correct approach is to define the mask directly based on the hardware
limitations.
The MMP/PXA PDMA controller is a 32-bit DMA engine. This is supported by
datasheets and various dtsi files for PXA25x, PXA27x, PXA3xx, and MMP2,
all of which are 32-bit systems.
This patch simplifies the driver's logic by replacing the 'u64 dma_mask'
field with a simpler 'u32 dma_width' to store the addressing capability
in bits. The complex if/else block in probe() is then replaced with a
single, clear call to dma_set_mask_and_coherent(). This sets a fixed
32-bit DMA mask for "marvell,pdma-1.0" and a 64-bit mask for
"spacemit,k1-pdma," matching each device's hardware capabilities.
Finally, this change also works around a specific build error encountered
with clang-20 on x86_64 allyesconfig. The shift-count-overflow error is
caused by a known clang compiler issue where the DMA_BIT_MASK(n) macro's
ternary operator is not correctly evaluated in static initializers. By
moving the macro's evaluation into the probe() function, the driver avoids
this compiler bug.
Fixes: 5cfe585d86 ("dmaengine: mmp_pdma: Add SpacemiT K1 PDMA support with 64-bit addressing")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Closes: https://lore.kernel.org/lkml/CA+G9fYsPcMfW-e_0_TRqu4cnwqOqYF3aJOeKUYk6Z4qRStdFvg@mail.gmail.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guodong Xu <guodong@riscstar.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5811e6297 ]
If the pre-operation file size is read before locking the inode and
quiescing O_DIRECT writes, then nfs_truncate_last_folio() might end up
overwriting valid file data.
Fixes: b1817b18ff ("NFS: Protect against 'eof page pollution'")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
