[ Upstream commit 62f7edd599 ]
Implement soft_reset, suspend, and resume callbacks using
genphy_soft_reset(), genphy_suspend(), and genphy_resume()
to fix PHY initialization and power management issues.
The soft_reset callback is needed to properly recover the PHY after an
ifconfig down/up cycle. Without it, the PHY can remain in power-down
state, causing MDIO register access failures during config_init().
The soft reset ensures the PHY is operational before configuration.
The suspend/resume callbacks enable proper power management during
system suspend/resume cycles.
Fixes: b2908a989c ("net: phy: add driver for MaxLinear MxL86110 PHY")
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Link: https://patch.msgid.link/20251223120940.407195-1-stefano.r@variscite.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c0856c225 ]
When the ping program uses an IPPROTO_ICMP socket to send ICMP_ECHO
messages, ICMP_MIB_OUTMSGS is counted twice.
ping_v4_sendmsg
ping_v4_push_pending_frames
ip_push_pending_frames
ip_finish_skb
__ip_make_skb
icmp_out_count(net, icmp_type); // first count
icmp_out_count(sock_net(sk), user_icmph.type); // second count
However, when the ping program uses an IPPROTO_RAW socket,
ICMP_MIB_OUTMSGS is counted correctly only once.
Therefore, the first count should be removed.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Signed-off-by: yuan.gao <yuan.gao@ucloud.cn>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20251224063145.3615282-1-yuan.gao@ucloud.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34f3ff52cb ]
Commit 15faa1f67a ("lan966x: Fix crash when adding interface under a lag")
fixed a similar issue in the lan966x driver caused by a NULL pointer dereference.
The ocelot_set_aggr_pgids() function in the ocelot driver has similar logic
and is susceptible to the same crash.
This issue specifically affects the ocelot_vsc7514.c frontend, which leaves
unused ports as NULL pointers. The felix_vsc9959.c frontend is unaffected as
it uses the DSA framework which registers all ports.
Fix this by checking if the port pointer is valid before accessing it.
Fixes: 528d3f190c ("net: mscc: ocelot: drop the use of the "lags" array")
Signed-off-by: Jerry Wu <w.7erry@foxmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/tencent_75EF812B305E26B0869C673DD1160866C90A@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3128df6be1 ]
When using an 802.1ad bridge with vlan_tunnel, the C-VLAN tag is
incorrectly stripped from frames during egress processing.
br_handle_egress_vlan_tunnel() uses skb_vlan_pop() to remove the S-VLAN
from hwaccel before VXLAN encapsulation. However, skb_vlan_pop() also
moves any "next" VLAN from the payload into hwaccel:
/* move next vlan tag to hw accel tag */
__skb_vlan_pop(skb, &vlan_tci);
__vlan_hwaccel_put_tag(skb, vlan_proto, vlan_tci);
For QinQ frames where the C-VLAN sits in the payload, this moves it to
hwaccel where it gets lost during VXLAN encapsulation.
Fix by calling __vlan_hwaccel_clear_tag() directly, which clears only
the hwaccel S-VLAN and leaves the payload untouched.
This path is only taken when vlan_tunnel is enabled and tunnel_info
is configured, so 802.1Q bridges are unaffected.
Tested with 802.1ad bridge + VXLAN vlan_tunnel, verified C-VLAN
preserved in VXLAN payload via tcpdump.
Fixes: 11538d039a ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Alexandre Knecht <knecht.alexandre@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20251228020057.2788865-1-knecht.alexandre@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a428e0da12 ]
devlink_alloc() may return NULL on allocation failure, but
prestera_devlink_alloc() unconditionally calls devlink_priv() on
the returned pointer.
This leads to a NULL pointer dereference if devlink allocation fails.
Add a check for a NULL devlink pointer and return NULL early to avoid
the crash.
Fixes: 34dd1710f5 ("net: marvell: prestera: Add basic devlink support")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Acked-by: Elad Nachman <enachman@marvell.com>
Link: https://patch.msgid.link/20251230052124.897012-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7811ba4524 ]
Currently last_gc is being updated everytime a new connection is
tracked, that means that it is updated even if a GC wasn't performed.
With a sufficiently high packet rate, it is possible to always bypass
the GC, causing the list to grow infinitely.
Update the last_gc value only when a GC has been actually performed.
Fixes: d265929930 ("netfilter: nf_conncount: reduce unnecessary GC")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d077e8119d ]
In nf_tables_newrule(), if nft_use_inc() fails, the function jumps to
the err_release_rule label without freeing the allocated flow, leading
to a memory leak.
Fix this by adding a new label err_destroy_flow and jumping to it when
nft_use_inc() fails. This ensures that the flow is properly released
in this error case.
Fixes: 1689f25924 ("netfilter: nf_tables: report use refcount overflow")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014a17deb4 ]
GPIO drivers with latch input support may miss short pulses on input
pins even when input latching is enabled. The generic interrupt logic in
the pca953x driver reports interrupts by comparing the current input
value against the previously sampled one and only signals an event when
a level change is observed between two reads.
For short pulses, the first edge is captured when the input register is
read, but if the signal returns to its previous level before the read,
the second edge is not observed. As a result, successive pulses can
produce identical input values at read time and no level change is
detected, causing interrupts to be missed. Below timing diagram shows
this situation where the top signal is the input pin level and the
bottom signal indicates the latched value.
─────┐ ┌──*───────────────┐ ┌──*─────────────────┐ ┌──*───
│ │ . │ │ . │ │ .
│ │ │ │ │ │ │ │ │
└──*──┘ │ └──*──┘ │ └──*──┘ │
Input │ │ │ │ │ │
▼ │ ▼ │ ▼ │
IRQ │ IRQ │ IRQ │
. . .
─────┐ .┌──────────────┐ .┌────────────────┐ .┌──
│ │ │ │ │ │
│ │ │ │ │ │
└────────*┘ └────────*┘ └────────*┘
Latched │ │ │
▼ ▼ ▼
READ 0 READ 0 READ 0
NO CHANGE NO CHANGE
PCAL variants provide an interrupt status register that records which
pins triggered an interrupt, but the status and input registers cannot
be read atomically. The interrupt status is only cleared when the input
port is read, and the input value must also be read to determine the
triggering edge. If another interrupt occurs on a different line after
the status register has been read but before the input register is
sampled, that event will not be reflected in the earlier status
snapshot, so relying solely on the interrupt status register is also
insufficient.
Support for input latching and interrupt status handling was previously
added by [1], but the interrupt status-based logic was reverted by [2]
due to these issues. This patch addresses the original problem by
combining both sources of information. Events indicated by the interrupt
status register are merged with events detected through the existing
level-change logic. As a result:
* short pulses, whose second edges are invisible, are detected via the
interrupt status register, and
* interrupts that occur between the status and input reads are still
caught by the generic level-change logic.
This significantly improves robustness on devices that signal interrupts
as short pulses, while avoiding the issues that led to the earlier
reversion. In practice, even if only the first edge of a pulse is
observable, the interrupt is reliably detected.
This fixes missed interrupts from an Ilitek touch controller with its
interrupt line connected to a PCAL6416A, where active-low pulses are
approximately 200 us long.
[1] commit 44896beae6 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
[2] commit d6179f6c62 ("gpio: pca953x: Improve interrupt support")
Fixes: d6179f6c62 ("gpio: pca953x: Improve interrupt support")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20251217153050.142057-1-ernestvanhoecke@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4f335b410 ]
The chip_$level() macros take struct gpio_chip as argument so make it
follow the convention of using the 'gpiochip_' prefix.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: a7ac22d53d ("gpiolib: fix race condition for gdev->srcu")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36a3200575 ]
During nft_synproxy eval we are reading nf_synproxy_info struct which
can be modified on update operation concurrently. As nf_synproxy_info
struct fits in 32 bits, use READ_ONCE/WRITE_ONCE annotations.
Fixes: ee394f96ad ("netfilter: nft_synproxy: add synproxy stateful object support")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7711f4bb4b ]
set->klen has to be used, not sizeof(). The latter only compares a
single register but a full check of the entire key is needed.
Example:
table ip t {
map s {
typeof iifname . ip saddr : verdict
flags interval
}
}
nft add element t s '{ "lo" . 10.0.0.0/24 : drop }' # no error, expected
nft add element t s '{ "lo" . 10.0.0.0/24 : drop }' # no error, expected
nft add element t s '{ "lo" . 10.0.0.0/8 : drop }' # bug: no error
The 3rd 'add element' should be rejected via -ENOTEMPTY, not -EEXIST,
so userspace / nft can report an error to the user.
The latter is only correct for the 2nd case (re-add of existing element).
As-is, userspace is told that the command was successful, but no elements were
added.
After this patch, 3rd command gives:
Error: Could not process rule: File exists
add element t s { "lo" . 127.0.0.0/8 . "lo" : drop }
^^^^^^^^^^^^^^^^^^^^^^^^^
Fixes: 0eb4b5ee33 ("netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a988caeed9 ]
The commit 616effc027 ("arm64: dts: imx8: Fix lpuart DMA channel
order") swap uart rx and tx channel at common imx8-ss-dma.dtsi. But miss
update imx8qm-ss-dma.dtsi.
The commit 5a8e9b022e ("arm64: dts: imx8qm-ss-dma: Pass lpuart
dma-names") just simple add dma-names as binding doc requirement.
Correct lpuart0 - lpuart3 dma rx and tx channels, and use defines for
the FSL_EDMA_RX flag.
Fixes: 5a8e9b022e ("arm64: dts: imx8qm-ss-dma: Pass lpuart dma-names")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c63749a7dd ]
Add missing 'clocks' property to LAN8740Ai PHY node, to allow the PHY driver
to manage LAN8740Ai CLKIN reference clock supply. This fixes sporadic link
bouncing caused by interruptions on the PHY reference clock, by letting the
PHY driver manage the reference clock and assure there are no interruptions.
This follows the matching PHY driver recommendation described in commit
bedd8d78ab ("net: phy: smsc: LAN8710/20: add phy refclk in support")
Fixes: 8d6712695b ("arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdf4e631ee ]
On this SoM eqos is the primary ethernet interface, Ka-Ro fuses the
address for it in eth_mac1, eth_mac2 seems to be left unfused. In their
downstream u-boot they fetch it from eth_mac1 [1][2], by setting alias
of eqos to ethernet0, the driver then fetches the mac address based on
the alias number.
Set eqos to read from eth_mac1 instead of eth_mac2. Also set fec to
point at eth_mac2 as it may be fused later even though it is disabled
by default.
With this changed barebox is now capable of loading the correct address.
Link: 3805432784/drivers/net/dwc_eth_qos.c (L1167) [1]
Link: 3805432784/arch/arm/dts/imx8mp-karo.dtsi (L12) [2]
Fixes: bac63d7c5f ("arm64: dts: freescale: add Ka-Ro Electronics tx8p-ml81 COM")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 056c688751 ]
The compatibles should include the SoM compatible, this board is based
on the Ka-Ro TX8P-ML81 SoM, so add it to allow using shared code in the
bootloader which uses upstream Linux devicetrees as a base.
Also add the hardware revision to the board compatible to handle
revision specific quirks in the bootloader/userspace.
This is a breaking change, but it is early enough that it can be
corrected without causing any issues.
Fixes: 03f07be54c ("arm64: dts: freescale: Add the GOcontroll Moduline Display baseboard")
Signed-off-by: Maud Spierings <maudspierings@gocontroll.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a4eedd49 ]
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef4 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Fixes: 56c27310c1 ("ARM: dts: imx: Add Advantech BA-16 Qseven module")
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca643894a3 ]
For SD card, according to the spec requirement, for sd card power reset
operation, it need sd card supply voltage to be lower than 0.5v and keep
over 1ms, otherwise, next time power back the sd card supply voltage to
3.3v, sd card can't support SD3.0 mode again.
To match such requirement on imx8qm-mek board, add 4.8ms delay between
sd power off and power on.
Fixes: 307fd14d4b ("arm64: dts: imx: add imx8qm mek support")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0d8678c2f ]
light sensor isl29023 share the interrupt with lsm303arg, but these
two devices use different interrupt type. According to the datasheet
of these two devides, both support low level trigger type, so correct
the interrupt type here to avoid the following error log:
irq: type mismatch, failed to map hwirq-11 for gpio@5d0c0000!
Fixes: 9918092cbb ("arm64: dts: imx8qm-mek: add i2c0 and children devices")
Fixes: 1d8a9f043a ("arm64: dts: imx8: use defines for interrupts")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961ac9d97b ]
The restarting message from PF to VF is sent twice during AER error
handling: once from adf_error_detected() and again from
adf_disable_sriov().
This causes userspace subservices to shutdown unexpectedly when they
receive a duplicate restarting message after already being restarted.
Avoid calling adf_pf2vf_notify_restarting() and
adf_pf2vf_wait_for_restarting_complete() from adf_error_detected() so
that the restarting msg is sent only once from PF to VF.
Fixes: 9567d3dc76 ("crypto: qat - improve aer error reset handling")
Signed-off-by: Harshita Bhilwaria <harshita.bhilwaria@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Reviewed-by: Ravikumar PM <ravikumar.pm@intel.com>
Reviewed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa917d3d57 ]
In mt8189-pinctrl driver, a previous commit changed the register base
name array (mt8189_pinctrl_register_base_names) entry name and order to
align it with the same name and order as the "mediatek,mt8189-pinctrl"
devicetree bindings. The new order (by ascending register address) now
causes an issue with MT8189 pinctrl configuration.
MT8189 SoC has multiple base addresses for the pin configuration
registers. Several constant data structures, declaring each pin
configuration, are using PIN_FIELD_BASE() macro which i_base parameter
indicates for a given pin the lookup index in the base register address
array of the driver internal data for the configuration register
read/write accesses. But in practice, this parameter is given a
hardcoded numerical value that corresponds to the expected base
register entry index in mt8189_pinctrl_register_base_names array.
Since this array reordering, the i_base index matching is no more
correct.
So, in order to avoid modifying over a thousand of PIN_FIELD_BASE()
calls, restore previous mt8189_pinctrl_register_base_names entry order.
Fixes: 518919276c ("pinctrl: mediatek: mt8189: align register base names to dt-bindings ones")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 570ad253a3 ]
The read result collection for buffered reads seems to run ahead of the
completion of subrequests under some circumstances, as can be seen in the
following log snippet:
9p_client_res: client 18446612686390831168 response P9_TREAD tag 0 err 0
...
netfs_sreq: R=00001b55[1] DOWN TERM f=192 s=0 5fb2/5fb2 s=5 e=0
...
netfs_collect_folio: R=00001b55 ix=00004 r=4000-5000 t=4000/5fb2
netfs_folio: i=157f3 ix=00004-00004 read-done
netfs_folio: i=157f3 ix=00004-00004 read-unlock
netfs_collect_folio: R=00001b55 ix=00005 r=5000-5fb2 t=5000/5fb2
netfs_folio: i=157f3 ix=00005-00005 read-done
netfs_folio: i=157f3 ix=00005-00005 read-unlock
...
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=c
netfs_collect_stream: R=00001b55[0:] cto=5fb2 frn=ffffffff
netfs_collect_state: R=00001b55 col=5fb2 cln=6000 n=8
...
netfs_sreq: R=00001b55[2] ZERO SUBMT f=000 s=5fb2 0/4e s=0 e=0
netfs_sreq: R=00001b55[2] ZERO TERM f=102 s=5fb2 4e/4e s=5 e=0
The 'cto=5fb2' indicates the collected file pos we've collected results to
so far - but we still have 0x4e more bytes to go - so we shouldn't have
collected folio ix=00005 yet. The 'ZERO' subreq that clears the tail
happens after we unlock the folio, allowing the application to see the
uncleared tail through mmap.
The problem is that netfs_read_unlock_folios() will unlock a folio in which
the amount of read results collected hits EOF position - but the ZERO
subreq lies beyond that and so happens after.
Fix this by changing the end check to always be the end of the folio and
never the end of the file.
In the future, I should look at clearing to the end of the folio here rather
than adding a ZERO subreq to do this. On the other hand, the ZERO subreq can
run in parallel with an async READ subreq. Further, the ZERO subreq may still
be necessary to, say, handle extents in a ceph file that don't have any
backing store and are thus implicitly all zeros.
This can be reproduced by creating a file, the size of which doesn't align
to a page boundary, e.g. 24998 (0x5fb2) bytes and then doing something
like:
xfs_io -c "mmap -r 0 0x6000" -c "madvise -d 0 0x6000" \
-c "mread -v 0 0x6000" /xfstest.test/x
The last 0x4e bytes should all be 00, but if the tail hasn't been cleared
yet, you may see rubbish there. This can be reproduced with kafs by
modifying the kernel to disable the call to netfs_read_subreq_progress()
and to stop afs_issue_read() from doing the async call for NETFS_READAHEAD.
Reproduction can be made easier by inserting an mdelay(100) in
netfs_issue_read() for the ZERO-subreq case.
AFS and CIFS are normally unlikely to show this as they dispatch READ ops
asynchronously, which allows the ZERO-subreq to finish first. 9P's READ op is
completely synchronous, so the ZERO-subreq will always happen after. It isn't
seen all the time, though, because the collection may be done in a worker
thread.
Reported-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Link: https://lore.kernel.org/r/8622834.T7Z3S40VBb@weasel/
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://patch.msgid.link/938162.1766233900@warthog.procyon.org.uk
Fixes: e2d46f2ec3 ("netfs: Change the read result collector to only use one work item")
Tested-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Acked-by: Dominique Martinet <asmadeus@codewreck.org>
Suggested-by: Dominique Martinet <asmadeus@codewreck.org>
cc: Dominique Martinet <asmadeus@codewreck.org>
cc: Christian Schoenebeck <linux_oss@crudebyte.com>
cc: v9fs@lists.linux.dev
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e13150c1a ]
The `dma_unmap_sg()` functions should be called with the same nents as the
`dma_map_sg()`, not the value the map function returned.
Save the number of entries in struct thc_dma_configuration.
Fixes: a688404b2e ("HID: intel-thc-hid: intel-thc: Add THC DMA interfaces")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Even Xu <even.xu@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d3352e73a ]
RUST_FW_LOADER_ABSTRACTIONS was depended on by NOVA_CORE, but NOVA_CORE
is selected by DRM_NOVA. This creates a situation where, if DRM_NOVA is
selected, NOVA_CORE gets enabled but not RUST_FW_LOADER_ABSTRACTIONS,
which results in a build error.
Since the firmware loader is an implementation detail of the driver, it
should be enabled along with it, so change the "depends on" to a
"select".
Fixes: 54e6baf123 ("gpu: nova-core: add initial driver stub")
Closes: https://lore.kernel.org/oe-kbuild-all/202512061721.rxKGnt5q-lkp@intel.com/
Tested-by: Alyssa Ross <hi@alyssa.is>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patch.msgid.link/20251106-b4-select-rust-fw-v3-2-771172257755@nvidia.com
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 235a1eb8d2 ]
In unittest_data_add(), if of_resolve_phandles() fails, the allocated
unittest_data is not freed, leading to a memory leak.
Fix this by using scope-based cleanup helper __free(kfree) for automatic
resource cleanup. This ensures unittest_data is automatically freed when
it goes out of scope in error paths.
For the success path, use retain_and_null_ptr() to transfer ownership
of the memory to the device tree and prevent double freeing.
Fixes: 2eb46da2a7 ("of/selftest: Use the resolver to fixup phandles")
Suggested-by: Rob Herring <robh@kernel.org>
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://patch.msgid.link/20251231114915.234638-1-zilin@seu.edu.cn
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83f59076a1 ]
Previously, btrfs_get_or_create_delayed_node() set the delayed_node's
refcount before acquiring the root->delayed_nodes lock.
Commit e8513c012d ("btrfs: implement ref_tracker for delayed_nodes")
moved refcount_set inside the critical section, which means there is
no longer a memory barrier between setting the refcount and setting
btrfs_inode->delayed_node.
Without that barrier, the stores to node->refs and
btrfs_inode->delayed_node may become visible out of order. Another
thread can then read btrfs_inode->delayed_node and attempt to
increment a refcount that hasn't been set yet, leading to a
refcounting bug and a use-after-free warning.
The fix is to move refcount_set back to where it was to take
advantage of the implicit memory barrier provided by lock
acquisition.
Because the allocations now happen outside of the lock's critical
section, they can use GFP_NOFS instead of GFP_ATOMIC.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202511262228.6dda231e-lkp@intel.com
Fixes: e8513c012d ("btrfs: implement ref_tracker for delayed_nodes")
Tested-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Leo Martins <loemra.dev@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f157dd6613 ]
When evicting an inode the first thing we do is to setup tracing for it,
which implies fetching the root's id. But in btrfs_evict_inode() the
root might be NULL, as implied in the next check that we do in
btrfs_evict_inode().
Hence, we either should set the ->root_objectid to 0 in case the root is
NULL, or we move tracing setup after checking that the root is not
NULL. Setting the rootid to 0 at least gives us the possibility to trace
this call even in the case when the root is NULL, so that's the solution
taken here.
Fixes: 1abe9b8a13 ("Btrfs: add initial tracepoint support for btrfs")
Reported-by: syzbot+d991fea1b4b23b1f6bf8@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d991fea1b4b23b1f6bf8
Signed-off-by: Miquel Sabaté Solà <mssola@mssola.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68d4b3fa18 ]
[BUG]
There is a bug that if a subvolume has multi-level parent qgroups, and
is able to do a quick inherit, only the direct parent qgroup got
updated:
mkfs.btrfs -f -O quota $dev
mount $dev $mnt
btrfs subv create $mnt/subv1
btrfs qgroup create 1/100 $mnt
btrfs qgroup create 2/100 $mnt
btrfs qgroup assign 1/100 2/100 $mnt
btrfs qgroup assign 0/256 1/100 $mnt
btrfs qgroup show -p --sync $mnt
Qgroupid Referenced Exclusive Parent Path
-------- ---------- --------- ------ ----
0/5 16.00KiB 16.00KiB - <toplevel>
0/256 16.00KiB 16.00KiB 1/100 subv1
1/100 16.00KiB 16.00KiB 2/100 2/100<1 member qgroup>
2/100 16.00KiB 16.00KiB - <0 member qgroups>
btrfs subv snap -i 1/100 $mnt/subv1 $mnt/snap1
btrfs qgroup show -p --sync $mnt
Qgroupid Referenced Exclusive Parent Path
-------- ---------- --------- ------ ----
0/5 16.00KiB 16.00KiB - <toplevel>
0/256 16.00KiB 16.00KiB 1/100 subv1
0/257 16.00KiB 16.00KiB 1/100 snap1
1/100 32.00KiB 32.00KiB 2/100 2/100<1 member qgroup>
2/100 16.00KiB 16.00KiB - <0 member qgroups>
# Note that 2/100 is not updated, and qgroup numbers are inconsistent
umount $mnt
[CAUSE]
If the snapshot source subvolume belongs to a parent qgroup, and the new
snapshot target is also added to the new same parent qgroup, we allow a
quick update without marking qgroup inconsistent.
But that quick update only update the parent qgroup, without checking if
there is any more parent qgroups.
[FIX]
Iterate through all parent qgroups during the quick inherit.
Reported-by: Boris Burkov <boris@bur.io>
Fixes: b20fe56cd2 ("btrfs: qgroup: allow quick inherit if snapshot is created and added to the same parent")
Reviewed-by: Boris Burkov <boris@bur.io>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ee19a59a7 ]
qgroup_snapshot_quick_inherit() detects conditions where the snapshot
destination would land in the same parent qgroup as the snapshot source
subvolume. In this case we can avoid costly qgroup calculations and just
add the nodesize of the new snapshot to the parent.
However, in the case of squotas this is actually a double count, and
also an undercount for deeper qgroup nestings.
The following annotated script shows the issue:
btrfs quota enable --simple "$mnt"
# Create 2-level qgroup hierarchy
btrfs qgroup create 2/100 "$mnt" # Q2 (level 2)
btrfs qgroup create 1/100 "$mnt" # Q1 (level 1)
btrfs qgroup assign 1/100 2/100 "$mnt"
# Create base subvolume
btrfs subvolume create "$mnt/base" >/dev/null
base_id=$(btrfs subvolume show "$mnt/base" | grep 'Subvolume ID:' | awk '{print $3}')
# Create intermediate snapshot and add to Q1
btrfs subvolume snapshot "$mnt/base" "$mnt/intermediate" >/dev/null
inter_id=$(btrfs subvolume show "$mnt/intermediate" | grep 'Subvolume ID:' | awk '{print $3}')
btrfs qgroup assign "0/$inter_id" 1/100 "$mnt"
# Create working snapshot with --inherit (auto-adds to Q1)
# src=intermediate (in only Q1)
# dst=snap (inheriting only into Q1)
# This double counts the 16k nodesize of the snapshot in Q1, and
# undercounts it in Q2.
btrfs subvolume snapshot -i 1/100 "$mnt/intermediate" "$mnt/snap" >/dev/null
snap_id=$(btrfs subvolume show "$mnt/snap" | grep 'Subvolume ID:' | awk '{print $3}')
# Fully complete snapshot creation
sync
# Delete working snapshot
# Q1 and Q2 will lose the full snap usage
btrfs subvolume delete "$mnt/snap" >/dev/null
# Delete intermediate and remove from Q1
# Q1 and Q2 will lose the full intermediate usage
btrfs qgroup remove "0/$inter_id" 1/100 "$mnt"
btrfs subvolume delete "$mnt/intermediate" >/dev/null
# Q1 should be at 0, but still has 16k. Q2 is "correct" at 0 (for now...)
# Trigger cleaner, wait for deletions
mount -o remount,sync=1 "$mnt"
btrfs subvolume sync "$mnt" "$snap_id"
btrfs subvolume sync "$mnt" "$inter_id"
# Remove Q1 from Q2
# Frees 16k more from Q2, underflowing it to 16EiB
btrfs qgroup remove 1/100 2/100 "$mnt"
# And show the bad state:
btrfs qgroup show -pc "$mnt"
Qgroupid Referenced Exclusive Parent Child Path
-------- ---------- --------- ------ ----- ----
0/5 16.00KiB 16.00KiB - - <toplevel>
0/256 16.00KiB 16.00KiB - - base
1/100 16.00KiB 16.00KiB - - <0 member qgroups>
2/100 16.00EiB 16.00EiB - - <0 member qgroups>
Fix this by simply not doing this quick inheritance with squotas.
I suspect that it is also wrong in normal qgroups to not recurse up the
qgroup tree in the quick inherit case, though other consistency checks
will likely fix it anyway.
Fixes: b20fe56cd2 ("btrfs: qgroup: allow quick inherit if snapshot is created and added to the same parent")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Boris Burkov <boris@bur.io>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278712d20b ]
This reverts commit ab2068a6fb.
When probing the exp-attached sata device, libsas/libata will issue a
hard reset in sas_probe_sata() -> ata_sas_async_probe(), then a
broadcast event will be received after the disk probe fails, and this
commit causes the probe will be re-executed on the disk, and a faulty
disk may get into an indefinite loop of probe.
Therefore, revert this commit, although it can fix some temporary issues
with disk probe failure.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Link: https://patch.msgid.link/20251202065627.140361-1-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4bb6daf4a ]
When a W-LUN resume fails, its parent devices in the SCSI hierarchy,
including the scsi_target, may be runtime suspended. Subsequently, the
error handler in ufshcd_recover_pm_error() fails to set the W-LUN device
back to active because the parent target is not active. This results in
the following errors:
google-ufshcd 3c2d0000.ufs: ufshcd_err_handler started; HBA state eh_fatal; ...
ufs_device_wlun 0:0:0:49488: START_STOP failed for power mode: 1, result 40000
ufs_device_wlun 0:0:0:49488: ufshcd_wl_runtime_resume failed: -5
...
ufs_device_wlun 0:0:0:49488: runtime PM trying to activate child device 0:0:0:49488 but parent (target0:0:0) is not active
Address this by:
1. Ensuring the W-LUN's parent scsi_target is runtime resumed before
attempting to set the W-LUN to active within
ufshcd_recover_pm_error().
2. Explicitly checking for power.runtime_error on the HBA and W-LUN
devices before calling pm_runtime_set_active() to clear the error
state.
3. Adding pm_runtime_get_sync(hba->dev) in
ufshcd_err_handling_prepare() to ensure the HBA itself is active
during error recovery, even if a child device resume failed.
These changes ensure the device power states are managed correctly
during error recovery.
Signed-off-by: Brian Kao <powenkao@google.com>
Tested-by: Brian Kao <powenkao@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20251112063214.1195761-1-powenkao@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1237c203f ]
This was reported by the KUnit tests in the later patches.
See MS-ERREF 2.3.1 STATUS_NO_DATA_DETECTED. Keep it consistent with the
value in the documentation.
Signed-off-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b50fca34 ]
This was reported by the KUnit tests in the later patches.
See MS-ERREF 2.3.1 STATUS_DEVICE_DOOR_OPEN. Keep it consistent with the
value in the documentation.
Signed-off-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f99caa895 ]
This was reported by the KUnit tests in the later patches.
See MS-ERREF 2.3.1 STATUS_UNABLE_TO_FREE_VM. Keep it consistent with the
value in the documentation.
Signed-off-by: ChenXiaoSong <chenxiaosong@kylinos.cn>
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7329417fc9 ]
On a 32-bit ARM system, the audio_decoder struct ends up being too large
for dp_retrain_link_dp_test.
link_dp_cts.c:157:1: error: the frame size of 1328 bytes is larger than
1280 bytes [-Werror=frame-larger-than=]
This is mitigated by shrinking the members of the struct and avoids
having to deal with dynamic allocation.
feed_back_divider is assigned but otherwise unused. Remove both.
pixel_repetition looks like it should be a bool since it's only ever
assigned to 1. But there are checks for 2 and 4. Reduce to uint8_t.
Remove ss_percentage_divider. Unused.
Shrink refresh_rate as it gets assigned to at most a 3 digit integer
value.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3849efdc78)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2a8fc27dd ]
When automounting, the fs_context should be fixed up to use the cred
from the parent filesystem, since the operation is just extending the
namespace. Authorisation to enter that namespace will already have been
provided by the preceding lookup.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57d508b5f7 ]
'version' is an enum, thus cast of pointer on 64-bit compile test with
clang W=1 causes:
rockchip_pdm.c:583:17: error: cast to smaller integer type 'enum rk_pdm_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
This was already fixed in commit 49a4a8d126 ("ASoC: rockchip: Fix
Wvoid-pointer-to-enum-cast warning") but then got bad in
commit 9958d85968 ("ASoC: Use device_get_match_data()").
Discussion on LKML also pointed out that 'uintptr_t' is not the correct
type and either 'kernel_ulong_t' or 'unsigned long' should be used,
with several arguments towards the latter [1].
Link: https://lore.kernel.org/r/CAMuHMdX7t=mabqFE5O-Cii3REMuyaePHmqX+j_mqyrn6XXzsoA@mail.gmail.com/ [1]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251203141644.106459-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e47c3cc64 ]
We have observed an NFSv4 client receiving a LOCK reply with a status of
NFS4ERR_OLD_STATEID and subsequently retrying the LOCK request with an
earlier seqid value in the stateid. As this was for a new lockowner,
that would imply that nfs_set_open_stateid_locked() had updated the open
stateid seqid with an earlier value.
Looking at nfs_set_open_stateid_locked(), if the incoming seqid is out
of sequence, the task will sleep on the state->waitq for up to 5
seconds. If the task waits for the full 5 seconds, then after finishing
the wait it'll update the open stateid seqid with whatever value the
incoming seqid has. If there are multiple waiters in this scenario,
then the last one to perform said update may not be the one with the
highest seqid.
Add a check to ensure that the seqid can only be incremented, and add a
tracepoint to indicate when old seqids are skipped.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Reviewed-by: Benjamin Coddington <bcodding@hammerspace.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8581b19eb2 ]
There is reported 'scheduling while atomic' bug when using dm-snapshot on
real-time kernels. The reason for the bug is that the hlist_bl code does
preempt_disable() when taking the lock and the kernel attempts to take
other spinlocks while holding the hlist_bl lock.
Fix this by converting a hlist_bl spinlock into a regular spinlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f3e47d3f ]
There are two problems with the recursive correction:
1. It may cause denial-of-service. In fec_read_bufs, there is a loop that
has 253 iterations. For each iteration, we may call verity_hash_for_block
recursively. There is a limit of 4 nested recursions - that means that
there may be at most 253^4 (4 billion) iterations. Red Hat QE team
actually created an image that pushes dm-verity to this limit - and this
image just makes the udev-worker process get stuck in the 'D' state.
2. It doesn't work. In fec_read_bufs we store data into the variable
"fio->bufs", but fio bufs is shared between recursive invocations, if
"verity_hash_for_block" invoked correction recursively, it would
overwrite partially filled fio->bufs.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Guangwu Zhang <guazhang@redhat.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
