Add vendor prefix for SakuraPi.org, which produces
development boards like the SakuraPi-RK3308B.
Link: https://docs.sakurapi.org
Signed-off-by: Hsun Lai <i@chainsx.cn>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250521131108.5710-2-i@chainsx.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 3f5d336d64 ("arm64: dts: rockchip: Add support for rk3588s based board Cool Pi 4B")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-2-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
cd-gpios is used for sdcard detects for sdmmc.
Fixes: 791c154c39 ("arm64: dts: rockchip: Add support for rk3588 based board Cool Pi CM5 EVB")
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250524064223.5741-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The SW_MACHINE_COVER switch event was added to input event codes to
detect the removal of the back cover of the N900.
But on the PineNote its purpose is to detect when the front cover gets
closed, just like when a laptop lid is closed. Therefore SW_LID is the
appropriate linux code and not SW_MACHINE_COVER.
Reported-by: hrdl <git@hrdl.eu>
Helped-by: phantomas <phantomas@phantomas.xyz>
Link: https://lore.kernel.org/r/270f27c9-afd6-171d-7dce-fe1d71dd8f9a@wizzup.org/
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20250526161506.139028-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
For the RK3588 HDMI controller, the falling edge of DDC SDA and SCL
almost coincide and cannot be adjusted by HDMI registrer, resulting
in poor compatibility of DDC communication.
An improvement of the compatibility of DDC can be done by increasing
the driver strength of SCL and decreasing the driver strength of SDA
to increase the slope of the falling edge.
It should be noted that the maximum driving strength of hdmim0_tx1_scl
is only 3, which is different from that of the other IOs.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250522020537.1884771-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pcie0 already used 0 as its pci-domain, so pcie1 will fail to
allocate the same pci-domain if both of them are used.
rk-pcie 2a210000.pcie: PCIe Link up, LTSSM is 0x130011
rk-pcie 2a210000.pcie: PCIe Gen.2 x1 link up
rk-pcie 2a210000.pcie: Scanning root bridge failed
rk-pcie 2a210000.pcie: failed to initialize host
Fixes: d4b9fc2af4 ("arm64: dts: rockchip: Add rk3576 pcie nodes")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/1748918140-212263-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update the i2c1 bus noting that the unknown/unused device at 0x3c is an
iSmartWare SW2001 "encryption IC".
Based on the documentation I was able to find, this IC appears to be
used to authenticate a device for certain programs to ensure they only
run on authorized devices as a form of digital rights management.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20250604024119.381337-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the Ethernet Switch adapter connected to the
mezzanine connector on RK3588 Jaguar.
This adapter has a KSZ9896 Ethernet Switch with 4 1GbE Ethernet
connectors, two user controllable LEDs, and an M12 12-pin connector
which exposes the following signals:
- RS232/RS485 (max 250Kbps/500Kbps, RX pin1, TX pin2)
- two digital inputs (pin4 routed to GPIO3_C5 on SoC, pin5 to GPIO4_B4)
- two digital outputs (pin7 routed to GPIO3_D3 on SoC, pin8 to
GPIO3_D1)
- two analog inputs (pin10 to channel1 of ADS1015, pin11 to channel2)
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
[Andrew's review for gmac1 and switch@5f parts]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20250604-jaguar-mezz-eth-switch-v3-1-c68123240f9e@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the DSI controller, DSI DCPHY, and Huiling hl055fhav028c
1080x1920 panel for the Gameforce Ace.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20250603193930.323607-5-macroalpha82@gmail.com
[moved lcd_rst pin into a lcd pinctrl group with lcd_bl_en]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a function to init ggtt for kunit, and use the GGTT function for
initialising the GGTT node without populating it. This
prevents the test from ever knowing about struct xe_ggtt.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-11-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Split the GGTT PTE readout to a separate function, this is useful for
adding testcases in the next commit, and also cleaner than manually
reading out GGTT.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-10-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The users inside display have been converted to use thepte_encode_flags
callback, we can now remove the pte_encode_bo cb.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-9-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
For DPT, it is sufficient to get the GGTT encode flags to fill the DPT.
Create a function to return the encode flags, and then encode using the
BO address.
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://lore.kernel.org/r/20250505121924.921544-7-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Pinning large linear display framebuffers is becoming a bottleneck.
My plan of attack is doing a custom walk over the BO, this allows for
easier optimization of consecutive entries.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-6-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Obtain the id from the root tile. Likely this can be hardcoded to 0,
but use the clean solution of obtaining root id and doing that.
to_xe_device(ggtt->tile) can also be easily replaced with xe.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-5-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Instead of allocating inside xe_tile, create a new function that returns
an allocated struct xe_ggtt from xe_ggtt.c
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-4-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Another requirement of hiding more of struct xe_ggtt.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-3-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
This is the first step to hide the details of struct xe_ggtt.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250505121924.921544-2-dev@lankhorst.se
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF warning:
pinctrl-tb10x.c:815:34: warning: unused variable 'tb10x_pinctrl_dt_ids' [-Wunused-const-variable]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505301317.EI1caRC0-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250601105100.27927-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Emails to Jianlong Huang bounce since 9 months, so drop the person from
maintainers:
550 5.4.1 Recipient address rejected: Access denied.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250528104514.184122-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to simplify cleanup actions, use devres-enabled version of
gpiochip_add_data(). As the msm_pinctrl_remove() function is now empty,
drop it and all its calls from the corresponding pinctrl drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250513-pinctrl-msm-fix-v2-3-249999af0fc1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IOSF_MBI was only useful for some gen8 platforms, which were never
supported by Xe. Presumably needed for display at one point, but display
is fixed to put stubs in compat-i915-headers/vlv_sideband.h. (in
drm-intel-next: vlv_iosf_sb.h)
Link: https://lore.kernel.org/r/20250605074644.71036-1-dev@lankhorst.se
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
The mute led on those laptops is using ALC245 but requires a quirk to work
This patch enables the existing quirk for the devices.
Tested on my Victus 16-s1011nt Laptop and my friend's Victus
15-fa1xxx. The LED behaviour works as intended.
Cc: <stable@vger.kernel.org>
Signed-off-by: Edip Hazuri <edip@medip.dev>
Link: https://patch.msgid.link/20250609075943.13934-2-edip@medip.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the time being recalculate_boundary() is implemented with a
loop which shows up as costly in a perf profile, as depicted by
the annotate below:
0.00 : c057e934: 3d 40 7f ff lis r10,32767
0.03 : c057e938: 61 4a ff ff ori r10,r10,65535
0.21 : c057e93c: 7d 49 50 50 subf r10,r9,r10
5.39 : c057e940: 7d 3c 4b 78 mr r28,r9
2.11 : c057e944: 55 29 08 3c slwi r9,r9,1
3.04 : c057e948: 7c 09 50 40 cmplw r9,r10
2.47 : c057e94c: 40 81 ff f4 ble c057e940 <snd_pcm_ioctl+0xee0>
Total: 13.2% on that simple loop.
But what the loop does is to multiply the boundary by 2 until it is
over the wanted border. This can be avoided by using fls() to get the
boundary value order and shift it by the appropriate number of bits at
once.
This change provides the following profile:
0.04 : c057f6e8: 3d 20 7f ff lis r9,32767
0.02 : c057f6ec: 61 29 ff ff ori r9,r9,65535
0.34 : c057f6f0: 7d 5a 48 50 subf r10,r26,r9
0.23 : c057f6f4: 7c 1a 50 40 cmplw r26,r10
0.02 : c057f6f8: 41 81 00 20 bgt c057f718 <snd_pcm_ioctl+0xf08>
0.26 : c057f6fc: 7f 47 00 34 cntlzw r7,r26
0.09 : c057f700: 7d 48 00 34 cntlzw r8,r10
0.22 : c057f704: 7d 08 38 50 subf r8,r8,r7
0.04 : c057f708: 7f 5a 40 30 slw r26,r26,r8
0.35 : c057f70c: 7c 0a d0 40 cmplw r10,r26
0.13 : c057f710: 40 80 05 f8 bge c057fd08 <snd_pcm_ioctl+0x14f8>
0.00 : c057f714: 57 5a f8 7e srwi r26,r26,1
Total: 1.7% with that loopless alternative.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/4836e2cde653eebaf2709ebe30eec736bb8c67fd.1749202237.git.christophe.leroy@csgroup.eu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the Hardware DSP-based 10-band hardware equalizer on
Sound Blaster Core3D (CA0132) based cards for example the soundblaster
z and soundblaster x-ae5, allowing fine-grained audio tuning via
hardware registers.
Tested on Sound Blaster X-AE5. No regressions observed.
Signed-off-by: Lucy Thrun <lucy.thrun@digital-rabbithole.de>
Link: https://patch.msgid.link/20250603125304.507-1-lucy.thrun@digital-rabbithole.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently hsmp_send_message() uses down_timeout() with a 100ms timeout
to take the semaphore. However __hsmp_send_message(), the content of the
critical section, has a sleep in it. On systems with significantly
delayed scheduling behaviour this may take over 100ms.
Convert this method to down_interruptible(). Leave the error handling
the same as the documentation currently is not specific about what error
is returned.
Previous behaviour: a caller who competes with another caller stuck in
the critical section due to scheduler delays would receive -ETIME.
New behaviour: a caller who competes with another caller stuck in the
critical section due to scheduler delays will complete successfully.
Reviewed-by: Suma Hegde <suma.hegde@amd.com>
Tested-by: Suma Hegde <suma.hegde@amd.com>
Signed-off-by: Jake Hillion <jake@hillion.co.uk>
Link: https://lore.kernel.org/r/20250605-amd-hsmp-v2-2-a811bc3dd74a@hillion.co.uk
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
__hsmp_send_message sleeps between result read attempts and has a
timeout of 100ms. Under extreme load it's possible for these sleeps to
take a long time, exceeding the 100ms. In this case the current code
does not check the register and fails with ETIMEDOUT.
Refactor the loop to ensure there is at least one read of the register
after a sleep of any duration. This removes instances of ETIMEDOUT with
a single caller, even with a misbehaving scheduler. Tested on AMD
Bergamo machines.
Suggested-by: Blaise Sanouillet <linux@blaise.sanouillet.com>
Reviewed-by: Suma Hegde <suma.hegde@amd.com>
Tested-by: Suma Hegde <suma.hegde@amd.com>
Signed-off-by: Jake Hillion <jake@hillion.co.uk>
Link: https://lore.kernel.org/r/20250605-amd-hsmp-v2-1-a811bc3dd74a@hillion.co.uk
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The Sony DualSense wireless controller (PS5) features an internal mono
speaker, but it also provides a 3.5mm jack socket for headphone output
and headset microphone input.
Since this is a UAC1 device, it doesn't advertise any jack detection
capability. However, the controller is able to report HP & MIC insert
events via HID, i.e. through a dedicated input device managed by the
hid-playstation driver.
Add a quirk to create the jack controls for headphone and headset mic,
respectively, and setup an input handler for each of them in order to
intercept the related hotplug events.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250526-dualsense-alsa-jack-v1-9-1a821463b632@collabora.com
Adding a memory barrier before wake_up() in
snd_usb_soundblaster_remote_complete() is supposed to ensure the write
to mixer->rc_code is visible in wait_event_interruptible() from
snd_usb_sbrc_hwdep_read().
However, this is not really necessary, since wake_up() is just a wrapper
over __wake_up() which already executes a full memory barrier before
accessing the state of the task to be waken up.
Drop the redundant call to wmb() and implicitly fix the checkpatch
complaint:
WARNING: memory barrier without comment
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250526-dualsense-alsa-jack-v1-8-1a821463b632@collabora.com
Address all whitespace & blank line(s) related issues reported by
checkpatch.pl:
ERROR: trailing whitespace
ERROR: space required after that ',' (ctx:VxV)
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20250526-dualsense-alsa-jack-v1-2-1a821463b632@collabora.com
The area of memory that contains the metrics table may contain garbage
when the cycle starts. This normally doesn't matter because the cycle
itself will populate it with valid data, however commit 9f5595d5f0
("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep
cycles") started to use it during the check() phase. Depending upon
what garbage is in the table it's possible that the system will wait
2.5 seconds for even the first cycle, which will be visible to a user.
To prevent this from happening explicitly clear the table when logging
is started.
Fixes: 9f5595d5f0 ("platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep cycles")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250603132412.3555302-1-superm1@kernel.org
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Return -ENOMEM instead of success if kcalloc() fails.
Fixes: e37be5d85c ("platform/x86/intel: power-domains: Add interface to get Linux die ID")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/aEKvIGCt6d8Gcx4S@stanley.mountain
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Address a Smatch static checker warning regarding an unchecked
dereference in the function call:
set_cdie_id(i, cluster_info, plat_info)
when plat_info is NULL.
Instead of addressing this one case, in general if plat_info is NULL
then it can cause other issues. For example in a two package system it
will give warning for duplicate sysfs entry as package ID will be always
zero for both packages when creating string for attribute group name.
plat_info is derived from TPMI ID TPMI_BUS_INFO, which is integral to
the core TPMI design. Therefore, it should not be NULL on a production
platform. Consequently, the module should fail to load if plat_info is
NULL.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/platform-driver-x86/aEKvGCLd1qmX04Tc@stanley.mountain/T/#u
Fixes: 8a54e2253e ("platform/x86/intel-uncore-freq: Uncore frequency control via TPMI")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250606205300.2384494-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
It was reported that ideapad-laptop sometimes causes some recent (since
2024) Lenovo ThinkBook models shut down when:
- suspending/resuming
- closing/opening the lid
- (dis)connecting a charger
- reading/writing some sysfs properties, e.g., fan_mode, touchpad
- pressing down some Fn keys, e.g., Brightness Up/Down (Fn+F5/F6)
- (seldom) loading the kmod
The issue has existed since the launch day of such models, and there
have been some out-of-tree workarounds (see Link:) for the issue. One
disables some functionalities, while another one simply shortens
IDEAPAD_EC_TIMEOUT. The disabled functionalities have read_ec_data() in
their call chains, which calls schedule() between each poll.
It turns out that these models suffer from the indeterminacy of
schedule() because of their low tolerance for being polled too
frequently. Sometimes schedule() returns too soon due to the lack of
ready tasks, causing the margin between two polls to be too short.
In this case, the command is somehow aborted, and too many subsequent
polls (they poll for "nothing!") may eventually break the state machine
in the EC, resulting in a hard shutdown. This explains why shortening
IDEAPAD_EC_TIMEOUT works around the issue - it reduces the total number
of polls sent to the EC.
Even when it doesn't lead to a shutdown, frequent polls may also disturb
the ongoing operation and notably delay (+ 10-20ms) the availability of
EC response. This phenomenon is unlikely to be exclusive to the models
mentioned above, so dropping the schedule() manner should also slightly
improve the responsiveness of various models.
Fix these issues by migrating to usleep_range(150, 300). The interval is
chosen to add some margin to the minimal 50us and considering EC
responses are usually available after 150-2500us based on my test. It
should be enough to fix these issues on all models subject to the EC bug
without introducing latency on other models.
Tested on ThinkBook 14 G7+ ASP and solved both issues. No regression was
introduced in the test on a model without the EC bug (ThinkBook X IMH,
thanks Eric).
Link: 6c5db18c9e
Link: 42d1e68e50
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218771
Fixes: 6a09f21dd1 ("ideapad: add ACPI helpers")
Cc: stable@vger.kernel.org
Tested-by: Felix Yan <felixonmars@archlinux.org>
Tested-by: Eric Long <i@hack3r.moe>
Tested-by: Jianfei Zhang <zhangjianfei3@gmail.com>
Tested-by: Mingcong Bai <jeffbai@aosc.io>
Tested-by: Minh Le <minhld139@gmail.com>
Tested-by: Sicheng Zhu <Emmet_Z@outlook.com>
Signed-off-by: Rong Zhang <i@rong.moe>
Link: https://lore.kernel.org/r/20250525201833.37939-1-i@rong.moe
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add gain calibration support, using resistor values set on devicetree,
values to be set accordingly with ADC external RFilter, as explained in
the ad7606c-16 datasheet, rev0, page 37.
Usage example in the fdt yaml documentation.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250606-wip-bl-ad7606-calibration-v9-7-6e014a1f92a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Non functional, renaming chan-related chan_scale structure to a more
generic chan_info, to host other chan specific settings, not just
scale-related.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250606-wip-bl-ad7606-calibration-v9-6-6e014a1f92a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix ad7606_get_chan_config() fdt parsing function to exit for error in
case of invalid dt_schema values.
Idea is to not proceed when there are values that are not allowed under
the dt_schema.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250606-wip-bl-ad7606-calibration-v9-5-6e014a1f92a2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
