Fix a typo in the comment by correcting "deviece" to "device"
for clarity and readability.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20250407105002.107181-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the comment to reference `usbhs_mod_probe()` instead of
`usbhs_mod_init()`, and replace `dev_set_drvdata()` with
`platform_set_drvdata()`, as these are the correct functions used
in this context.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20250407105002.107181-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling LPM is done in hub workqueue, often in paths handling possible
link issues. So fail immediately on USB3 LPM issues and avoid hub wq
from unnecessary blocking, thus allowing it to handle other port events
faster.
Detect errors when enabling U1/U2 link states, and return immediately
if there is an issue.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow a USB3 link to enter U1/U2
hardware link power management LPM states. Reorder these requests
and send the more significant and likely to succeed first.
This is similar to the change done for disabling LPM
Enable LPM by first sending requests to the upstream hub of the device
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
These are more likely to succeed due to the shorter path, and LPM can
be considered enabled as link may go to U1/U2 LPM states after those.
Send the requests to the device after this, they allow the device
to initialte U1/U2 link transitions. Hub can already initiate U1/U2
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
Fail fast and bail out if a requests to the device fails.
This changes device initated LPM policy a bit. Device is no longer
able to initiate U2 if it failed or is not allowed to initiate
U1.
Enabling and disabling Link power management is done as part of
hub work. Avoid trying to send additional USB requests to a device
when there are known issues. It just causes hub work to block for
even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling device initiated USB3 link power management (LPM) may fail for
various reasons such as too long system exit latency, or link issues.
These are not good reason to disable hub initiated LPM U1/U2
states, especially as it requires sending more requests over a
possibly broken link, causing the hub work to block for even longer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move device configured check into usb_device_may_initiate_lpm() instead
of calling it before the function.
No functional changes, helps rework to fail faster during link power
management (LPM) enabling.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several usb requests are needed to allow or forbid a USB3 link from
going into U1 or U2 hardware link power management (LPM) states.
Fail fast on issues in LPM disabling path. LPM disabling is done in hub
workqueue paths that are often already handling possible link issues.
Enabling and disabling LPM involves four usb requests.
Two requests sent to the upstream hub of the connected device:
SetPortFeature(U1_TIMEOUT)
SetPortFeature(U2_TIMEOUT)
And two to the device itself:
SetFeature(U1_ENABLE)
SetFeature(U2_ENABLE)
The requests to the hub sets the inactivity timeout used by the hub to
know when to initiate U1 and U2 LPM link state transitions.
These requests are also used prevent U1/U2 LPM transitions completely
by passing zero timeout value.
The requsts sent to the device only controls if device is allowed to
initiate U1/U2 transitions. If not enabled then only hub initiates U1/U2
transitions. Hub may block these device initiated attempts.
Reorder and send the hub requests first, these are more likely to succeed
due to shorter path, and we can consider LPM disabled if these succeed
as U1/U2 link state can not be entered after that.
Fail immediately if a request fails, and don't try to enable back LPM
after a failed request, that will just send more LPM requests over a
bad link.
If a device request controlling device initiateed LPM fails then exit
immediately, but consider LPM disabled at this stage.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250314142000.93090-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a device path in the driver the snprintf() takes
up to 16 characters long argument along with the additional up to
12 characters for the signed integer (as it can't see the actual limits)
and tries to pack this into 16 bytes array. GCC complains about that
when build with `make W=1`:
drivers/usb/core/usb.c:705:25: note: ‘snprintf’ output between 3 and 28 bytes into a destination of size 16
Since everything works until now, let's just check for the potential
buffer overflow and bail out. It is most likely a never happen situation,
but at least it makes GCC happy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250321164949.423957-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i.MX95 platform, USB wakeup setting is controlled by HSIO Block
Control:
HSIO Block Control Overview:
- The HSIO block control include configuration and status registers that
provide miscellaneous top-level controls for clocking, beat limiter
enables, wakeup signal enables and interrupt status for the PCIe and USB
interfaces.
The wakeup function of HSIO blkctl is basically same as non-core, except
improvements about power lost cases. This will add the wakeup setting for
HSIO blkctl on i.MX95. It will firstly ioremap hsio blkctl memory, then do
wakeup setting as needs.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-4-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In previous imx platform, normal USB controller interrupt and wakeup
interrupt are bound to one irq line. However, it changes on latest
i.MX95 platform since it has a dedicated irq line for wakeup interrupt.
This will add wakeup interrupt handling for i.MX95 to support various
wakeup events.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible string "fsl,imx95-usbmisc" for i.MX95 platform and
restriction on reg property.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX95 USB2.0 controller is mostly compatible with i.MX7D, except it
requires a second interrupt for wakeup handling. Add the compatible string
for the i.MX95 platform, add the iommus property, and enforce the
interrupt property restriction. Keep the same restriction for existing
compatible strings.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250318150908.1583652-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the course of fixing up the usages of flexible arrays, Gustavo
submitted a patch updating the ehci-fsl driver. However, the patch
was wrong because the driver was using the .priv member of the
ehci_hcd structure incorrectly. The private data is not supposed to
be a wrapper containing the ehci_hcd structure; it is supposed to be a
sub-structure stored in the .priv member.
Fix the problem by replacing the ehci_fsl structure with
ehci_fsl_priv, containing only the private data, along with a suitable
conversion macro for accessing it. This removes the problem of having
data follow a flexible array member.
Reported-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/linux-usb/Z-R9BcnSzrRv5FX_@kspp/
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/8139e4cc-4e5c-40e2-9c4b-717ad3215868@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set WDM_READ flag in wdm_in_callback() for ZLP-s, otherwise when
userspace tries to poll for available data, it might - incorrectly -
believe there is something available, and when it tries to non-blocking
read it, it might get stuck in the read loop.
For example this is what glib does for non-blocking read (briefly):
1. poll()
2. if poll returns with non-zero, starts a read data loop:
a. loop on poll() (EINTR disabled)
b. if revents was set, reads data
I. if read returns with EINTR or EAGAIN, goto 2.a.
II. otherwise return with data
So if ZLP sets WDM_READ (#1), we expect data, and try to read it (#2).
But as that was a ZLP, and we are doing non-blocking read, wdm_read()
returns with EAGAIN (#2.b.I), so loop again, and try to read again
(#2.a.).
With glib, we might stuck in this loop forever, as EINTR is disabled
(#2.a).
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20250403144004.3889125-1-robert.hodaszi@digi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding.
No functional changes here, but saves some comments during reviews of
new patches built on existing code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250324125142.81910-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function don't return value, remove the invalid comment.
Signed-off-by: Li Qiong <liqiong@nfschina.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20250314101639.424013-1-liqiong@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to how it is done in the write path.
Add a disabled flag to track the function state and use it to exit the read
loops to ensure no readers get stuck when the function is disabled/unbound,
protecting against corruption when the waitq and spinlocks are reinitialized
in hidg_bind().
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Link: https://lore.kernel.org/r/20250318152207.330997-1-peter@korsgaard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are
getting ready to enable it, globally.
Move the conflicting declaration to the end of the structure. Notice
that `struct uvc_input_header_descriptor` is a flexible structure --a
structure that contains a flexible-array member.
With this, fix three of the following warnings:
drivers/usb/gadget/function/uvc_configfs.h:77:57: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/Z9dyY7_ydJiGqh_d@kspp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strncpy() is deprecated for NUL-terminated destination buffers; use
strscpy() instead. Since kzalloc() already zeroes out the destination
buffer, the potential NUL-padding by strncpy() is unnecessary. strscpy()
copies only the required characters and guarantees NUL-termination.
Since the destination buffer has a fixed length, strscpy() automatically
determines its size using sizeof() when the argument is omitted. This
makes an explicit sizeof() call unnecessary.
The source string is also NUL-terminated and meets the __must_be_cstr()
requirement of strscpy().
No functional changes intended.
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20250320165647.34859-2-thorsten.blum@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow specifying the connector directly in the USB controller node, as
allow in other USB controller bindings and commonly used for
"gpio-usb-b-connector". Linux already supports this without driver
changes.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20250325131848.127438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SM8750 uses the Synopsys DWC3 controller. Add this to the compatibles list
to utilize the DWC3 QCOM and DWC3 core framework. Other than a revision
bump to DWC3 controller rev2.00a, the controller on SM8750 does not add any
additional vendor specific features compared to previous chipsets.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Melody Olvera <melody.olvera@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250409-sm8750_usb_master-v4-3-6ec621c98be6@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3 device suspend/resume callbacks were being triggered during system
suspend and resume even if the device was already runtime-suspended.
This is redundant for device mode because the suspend and resume routines
are essentially identical for system PM and runtime PM.
To prevent these unnecessary callbacks, indicate to the PM core that it
can safely leave the device in runtime suspend if it's already
runtime-suspended in device mode by returning a positive value in
prepare() callback. This optimization only applies to devices without
pinctrl, as pinctrl has distinct logic tied to system suspend/resume.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250312223434.3071598-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although some Type-C DRD devices that do not support the DP Sink
function (such as Huawei Mate 40Pro), the Source Port initiates
Enter Mode CMD, but the device responds to Enter Mode ACK, the
Source port then initiates DP Status Update CMD, and the device
responds to DP Status Update NAK.
As PD2.0 spec ("6.4.4.3.4 Enter Mode Command"),A DR_Swap Message
Shall Not be sent during Modal Operation between the Port Partners.
At this time, the source port initiates DR_Swap message through the
"echo device > /sys/class/typec/port0/data_role" command to switch
the data role from host to device. The device will initiate a Hard
Reset for recovery, resulting in the failure of data role swap.
Therefore, when DP Status Update NAK is received, Exit Mode CMD is
initiated to exit the currently entered DP altmode.
Signed-off-by: Jos Wang <joswang@lenovo.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250209071926.69625-1-joswang1221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device can be unbound, so driver must also release memory for the wakeup
source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250406204051.63446-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpci chip vbus pin is possibly driven by an regulator. This patch
is adding support to enable an optional vdd regulator before probing.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpci-v1-1-4442c7d0ee1e@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The funciton tcpm_acc_attach is not setting the proper state when
calling tcpm_set_role. The function tcpm_set_role is currently only
handling TYPEC_STATE_USB. For the tcpm_acc_attach to switch into other
modal states tcpm_set_role needs to be extended by an extra state
parameter. This patch is handling the proper state change when calling
tcpm_acc_attach.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-3-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch extends the is_debug macro to cover the sink case (ufp). It
also handles the transition to access the DEBUG_ACC_ATTACHED state in
the sink case. It also handles the debounce case in which the cc
pins are not immediately valid after the plug event.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-2-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the function tcpm_acc_attach is not setting the data and role for
for the sink case we extend it to check for it first.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-tcpm-v1-1-b99f44badce8@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the typec connectors can have many muxes or switches for different
lanes (sbu, usb2, usb3) going into different modal states (usb2, usb3,
audio, debug) all of them will be called on typec_switch_set and
typec_mux_set. But not all of them will be handling the expected mode.
If one of the mux or switch will come back with EOPTNOSUPP this is no
reason to stop running through the next ones. Therefor we skip this
particular error value and continue calling the next.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250404-ml-topic-typec-mux-v1-1-22c0526381ba@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added the UCSI commands UCSI_GET_CAM_SUPPORTED, UCSI_GET_PD_MESSAGE,
UCSI_GET_ATTENTION_VDO and UCSI_SET_USB support in debugfs to enhance
PD/TypeC debugging capability
Signed-off-by: Madhu M <madhu.m@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250402070817.1016635-1-madhu.m@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei Matebook E Go tablet implements the UCSI interface in the
onboard EC. Add the glue driver to interface with the platform's UCSI
implementation.
This driver is inspired by the following drivers:
drivers/usb/typec/ucsi/ucsi_yoga_c630.c
drivers/usb/typec/ucsi/ucsi_glink.c
drivers/soc/qcom/pmic_glink_altmode.c
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250316094357.462022-1-mitltlatltl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit b73ec10a45 ("fs: add fastpath for dissolve_on_fput()"),
the namespace_{lock,unlock} has been replaced with scoped_guard
using the namespace_sem. This however now also skips processing of
'unmounted' list in namespace_unlock(), and mount is not (immediately)
cleaned up.
For example, this causes LTP move_mount02 fail:
...
move_mount02.c:80: TPASS: invalid-from-fd: move_mount() failed as expected: EBADF (9)
move_mount02.c:80: TPASS: invalid-from-path: move_mount() failed as expected: ENOENT (2)
move_mount02.c:80: TPASS: invalid-to-fd: move_mount() failed as expected: EBADF (9)
move_mount02.c:80: TPASS: invalid-to-path: move_mount() failed as expected: ENOENT (2)
move_mount02.c:80: TPASS: invalid-flags: move_mount() failed as expected: EINVAL (22)
tst_test.c:1833: TINFO: === Testing on ext3 ===
tst_test.c:1170: TINFO: Formatting /dev/loop0 with ext3 opts='' extra opts=''
mke2fs 1.47.2 (1-Jan-2025)
/dev/loop0 is apparently in use by the system; will not make a filesystem here!
tst_test.c:1170: TBROK: mkfs.ext3 failed with exit code 1
The test makes number of move_mount() calls but these are all designed to fail
with specific errno. Even after test, 'losetup -d' can't detach loop device.
Define a new guard for dissolve_on_fput, that will use namespace_{lock,unlock}.
Fixes: b73ec10a45 ("fs: add fastpath for dissolve_on_fput()")
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Link: https://lore.kernel.org/cad2f042b886bf0ced3d8e3aff120ec5e0125d61.1744297468.git.jstancek@redhat.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
The reset handshake attempts to kill the firmware, and it'll go
into a pretty much dead state once we do that. However, if it
times out, then we'll attempt to dump the firmware to be able
to see why it didn't respond. During this dump, we cannot treat
it as if it was still running, since we just tried to kill it,
otherwise dumping will attempt to send a DBGC stop command. As
this command will time out, we'll go into a reset loop.
For now, fix this by setting the trans->state to say firmware
isn't running before doing the reset handshake. In the longer
term, we should clean up the way this state is handled.
It's not entirely clear but it seems likely that this issue was
introduced by my rework of the error handling, prior to that it
would've been synchronous at that point and (I think) not have
attempted to reset since it was already doing down.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219967
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219968
Fixes: 7391b2a4f7 ("wifi: iwlwifi: rework firmware error handling")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250411104054.63aa4f56894d.Ife70cfe997db03f0d07fdef2b164695739a05a63@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In iomap_adjust_read_range, i is either the first !uptodate block, or it
is past last for the second loop looking for trailing uptodate blocks.
Assuming there's no overflow (there's no combination of huge folios and
tiny blksize) then yeah, there is no point in retesting that the same
block pointed to by i is uptodate since we hold the folio lock so nobody
else could have set it uptodate.
Signed-off-by: Gou Hao <gouhao@uniontech.com>
Link: https://lore.kernel.org/20250410071236.16017-1-gouhao@uniontech.com
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
getname_flags() should save __user pointer "filename" in filename->uptr.
However, this logic is broken by a recent refactoring. Fix it by passing
__user pointer filename to helper initname().
Fixes: 611851010c ("fs: dedup handling of struct filename init and refcounts bumps")
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/20250409220534.3635801-1-song@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Adding an unlikely() hint on the fd < 0 comparison return path improves
run-time performance of the poll() system call. gcov based coverage
analysis based on running stress-ng and a kernel build shows that this
path return path is highly unlikely.
Benchmarking on an Debian based Intel(R) Core(TM) Ultra 9 285K with
a 6.15-rc1 kernel and a poll of 1024 file descriptors with zero timeout
shows an call reduction from 32818 ns down to 32635 ns, which is a ~0.5%
performance improvement.
Results based on running 25 tests with turbo disabled (to reduce clock
freq turbo changes), with 30 second run per test and comparing the number
of poll() calls per second. The % standard deviation of the 25 tests
was 0.08%, so results are reliable.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/20250409155510.577490-1-colin.i.king@gmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
A set of small fixes, quirks and device ID additions that came in since
-rc1, none of them super stand out. There's also a change to Srini's
email address in MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmf5Aj8ACgkQJNaLcl1U
h9CpLAf9FE8grQXtlVv5DcIXCvmE4ZXLp3A+UKyuSzU5R0CYvbQ/eS+1pAYsSXzz
alXILKp/4lBxPxUjQdMUCw9uGX3Px+VX64IoNWZcvEqUNHlvqXcyAlIqN9UmWyWq
aX55h+gJdYuRj+6R/qPtQroqeqimcVAFi/iggeYJjiuKL2W9Bdy054Z0UgT2TtUC
Tw5e+9qinrHred8MoCe+FD0w0PKAsMSXVWNm2XSnwBUzURI4OWdD338kK8rODgFn
/7j75wX9FyJnnB+RZrju7H1fkIj+b+y1+7pLPHbZt9dyen2W/ftcdKexT7JtlQES
Ss/Pi4gVDRqT+2UEbEXz7MlhT2hXSw==
=7hPh
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v6.15-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.15
A set of small fixes, quirks and device ID additions that came in since
-rc1, none of them super stand out. There's also a change to Srini's
email address in MAINTAINERS.
Merge updates of the ACPI EC and button drivers for 6.15-rc2:
- Add suspend-to-idle EC wakeup quirks for Lenovo Go S (Mario
Limonciello).
- Prevent ACPI button from sending spurions KEY_POWER events to user
space in some cases after a recent update (Mario Limonciello).
* acpi-ec:
ACPI: EC: Set ec_no_wakeup for Lenovo Go S
* acpi-button:
ACPI: button: Only send `KEY_POWER` for `ACPI_BUTTON_NOTIFY_STATUS`
Clang warns (or errors with CONFIG_WERROR=y):
drivers/gpu/drm/sysfb/efidrm.c:353:11: error: variable 'screen_base' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
353 | else if (mem_flags & EFI_MEMORY_WB)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/sysfb/efidrm.c:356:7: note: uninitialized use occurs here
356 | if (!screen_base)
| ^~~~~~~~~~~
drivers/gpu/drm/sysfb/efidrm.c:353:7: note: remove the 'if' if its condition is always true
353 | else if (mem_flags & EFI_MEMORY_WB)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
354 | screen_base = devm_memremap(&pdev->dev, mem->start, resource_size(mem),
drivers/gpu/drm/sysfb/efidrm.c:261:27: note: initialize the variable 'screen_base' to silence this warning
261 | void __iomem *screen_base;
| ^
| = NULL
efidrm_get_mem_flags() can only return a mask that has at least one of
the tested values set so the else case is impossible but clang's static
analysis runs before inlining so it cannot know that.
Initialize screen_base to NULL and add a defensive error message in case
mem_flags were ever returned without one of the four valid values.
Fixes: 32ae90c66f ("drm/sysfb: Add efidrm for EFI displays")
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250410-efidrm-avoid-uninit-screen_info-warning-v2-1-b79646f58c24@kernel.org
According to our internal spec we need to now check if both
panel luminance and smooth brightness are available in panel for
us to be able to change brightness using luminance value.
--v2
-Add Fixes tag [Ankit]
Fixes: 6448149792 ("drm/i915/backlight: Check Luminance based brightness control for VESA")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250411060235.2732060-3-suraj.kandpal@intel.com
Commit 9748cb2dc3 ("VFS: repack DENTRY_ flags.") changed the value of
DCACHE_MOUNTED, which broke drgn's path_lookup() helper. drgn is forced
to hard-code it because it's a macro, and macros aren't preserved in
debugging information by default.
Enums, on the other hand, are included in debugging information. Convert
the DCACHE_* flag macros to an enum so that debugging tools like drgn
and bpftrace can make use of them.
Link: 2027d0fea8/drgn/helpers/linux/fs.py (L43-L46)
Signed-off-by: Omar Sandoval <osandov@fb.com>
Link: https://lore.kernel.org/177665a082f048cf536b9cd6af467b3be6b6e6ed.1744141838.git.osandov@fb.com
Signed-off-by: Christian Brauner <brauner@kernel.org>