Commit ba0fb44aed ("dma-mapping: replace zone_dma_bits by
zone_dma_limit") optimistically assumed that device-tree dma-ranges
property describes the system DMA limits. That assumption ignores DMA
limits of individual devices that are not encoded in device tree.
Commit 833bd284a4 ("arm64: mm: fix DMA zone when dma-ranges is
missing") fixed part of the problem for platforms that do not provide
dma-ranges at all. However platforms like SM8550-HDK provide DMA bus
limit, but have devices with stronger DMA limits.
of_dma_get_max_cpu_address() does not take device limitations into
account.
These platforms implicitly rely on DMA zone in low 32-bit RAM area.
Until we find a better way to figure out the optimal DMA zone range,
restore the low RAM DMA zone we had before commit ba0fb44aed.
Fixes: ba0fb44aed ("dma-mapping: replace zone_dma_bits by zone_dma_limit")
Closes: https://lore.kernel.org/r/1a0c7282-63e0-4add-8e38-3abe3e0a8e2f@linaro.org
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently there is no way to apply quirk on device only if certain panel
model is installed. This patch implements such mechanism by adding new
quirk type intel_dpcd_quirk which contains also sink_oui and sink_device_id
fields and using also them to figure out if applying quirk is needed.
New intel_init_dpcd_quirks is added and called after drm_dp_read_desc with
proper sink device identity read from dpcdc.
v3:
- !mem_is_zero fixed to mem_is_zero
v2:
- instead of using struct intel_quirk add new struct intel_dpcd_quirk
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902064241.1020965-2-jouni.hogander@intel.com
(cherry picked from commit b3b9136990)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The Variscite VAR-SOM-MX8MM System-on-Module cannot be used alone
without motherboard, so drop the usage of its compatible alone.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Herve Codina says:
================
This series add support for the QUICC Engine (QE) version of TSA and QMC
components.
CPM1 version is already supported and, as the QE version of those
component are pretty similar to the CPM1 version, the series extend
the already existing drivers to support for the QE version.
The TSA and QMC components are tightly coupled and so the series
provides modifications on both components.
Of course, this series can be split if it is needed. Let me know.
The series is composed of:
- Patches 1 and 2: Fixes related to TRNSYNC in the QMC driver
- Patches 3..6: Fixes of checkpatch detected issues in the TSA driver
- Patch 7: The QE TSA device-tree binding
- Patches 8..13: TSA driver preparations for adding support for QE
- Patches 14 and 15: The support for QE in TSA + MAINTAINERS update
- Patch 16: A TSA API improvement needed for the QE QMC driver
- Patch 17: A clarification in the QE QMC driver
- Patches 18..22: Fixes of checkpatch detected issues in the QMC driver
- Patch 23: The QE QMC device-tree binding
- Patches 24..31: QMC driver preparations for adding support for QE
- Patches 32 and 33: Missing features additions in QE code
- Patches 34..36: The QMC support for QE in QMC + MAINTAINERS update
Compared to the previous iteration, this v2 series updates device-tree
bindings and fixes issues detected by kernel test robots.
Related to the QE QMC device-tree binding, I kept the unit address in
decimal and the 3 compatible strings.
================
Link: https://lore.kernel.org/r/20240808071132.149251-1-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This warning was added by commit 07f86917a4 ("soc/fsl/qbman: Use
shared-dma-pool for QMan private memory allocations") but
RESERVEDMEM_OF_DECLARE usage was removed by
commit 3e62273ac6 ("soc: fsl: qbman: Remove RESERVEDMEM_OF_DECLARE
usage") . For non-popwerpc platforms, such as ls1043, this warning
is redundant. ls1043 itself uses shared-dma-mem.
Fixes: 3e62273ac6 ("soc: fsl: qbman: Remove RESERVEDMEM_OF_DECLARE usage")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20240802021651.3854295-1-xiaolei.wang@windriver.com
[chleroy: Added more details in commit message]
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
An iommu domain is allocated in portal_set_cpu() and is attached to
pcfg->dev in the same function.
Use iommu_paging_domain_alloc() to make it explicit.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240610085555.88197-14-baolu.lu@linux.intel.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The Freescale QMC controller driver supports both QE and CPM1.
Add the newly introduced QE files to the existing entry.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-37-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The QUICC Engine (QE) QMC can use a firmware to have the QMC working in
'soft-qmc' mode.
Handle this optional 'soft-qmc' firmware.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-36-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Add support for the QMC (QUICC Multichannel Controller) available in
some PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321.
This QE QMC is similar to the CPM QMC except that it uses UCCs (Unified
Communication Controllers) instead of SCCs (Serial Communication
Controllers). Also, compared against the CPM QMC, this QE QMC does not
use a fixed area for the UCC/SCC parameters area but it uses a dynamic
area allocated and provided to the hardware at runtime.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-35-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The PUSHSCHED command is missing in the QE header file.
This command is supported on MPC8321 and is used to modify the start
address for the task running on a given peripheral. It is needed for the
QMC in order to perform the re-initialization procedure and so, ensure
the correct UCC setup in that case.
Simply add the missing command in the commands list available in the QE
header file.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-34-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Introduce devm_cpm_muram_alloc() and devm_cpm_muram_alloc_fixed(), the
resource-managed version of cpm_muram_alloc and cpm_muram_alloc_fixed().
These resource-managed versions simplify the user avoiding the need to
call cpm_muram_free(). Indeed, the allocated area returned by these
functions will be automatically freed on driver detach.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-33-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of QMC.
In order to prepare the support for the QUICC Engine (QE) version of
QMC, introduce qmc_version to identify versions. This will enable the
code to make the distinction between several QMC implementations.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-32-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles CPM1 version of QMC. Even if GSMRL is specific to
the CPM1 version, the exact same purpose and format register (GUMRL) is
present in the QUICC Engine (QE) version of QMC. Compared to the QE
version, the values defined for the mode bitfield are different and the
0x0A value defined for the QMC mode is CPM1 specific.
In order to prepare the support for the QE version, rename this bitfield
value to clearly identify it as CPM1 specific.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-31-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of QMC, RPACK does not need to
be initialized. This is not the case in the QUICC Engine (QE) version.
In preparation of the support for QE, initialize the RPACK register
when the receiver is initialized and each time it is restarted.
This additional RPACK initialization has no impact in the CPM1 version
of QMC.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-30-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles CPM1 version of QMC and qmc_chan_command() is
clearly CPM1 specific.
In order to prepare the support for the QUICC Engine (QE) version,
rename qmc_chan_command() to reflect that point.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-29-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of QMC and initialize the QMC used
SCC. The QUICC Engine (QE) version uses an UCC (Unified Communication
Controllers) instead of the SCC (Serial Communication Controllers) used
in the CPM1 version. These controllers serve the same purpose and are
used in the same way but their inializations are slightly different.
In order to prepare the support for QE version of QMC, introduce
qmc_init_xcc() to initialize theses controllers (UCC in QE and SCC in
CPM1) and isolate the CPM1 specific SCC initialization in a specific
function.
Also introduce qmc_exit_xcc() for consistency to revert operations done
in qmc_init_xcc().
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-28-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of QMC. Resources initialisations
(i.e. retrieving base addresses and offsets of different parts) will
be slightly different in the QUICC Engine (QE) version. Indeed, in QE
version, some resources need to be allocated and are no more "staticaly"
defined.
In order to prepare the support for QE version, introduce
qmc_init_resource() to initialize those resources and isolate the CPM1
specific operations in a specific function.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-27-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles CPM1 version of QMC. In the QUICC Engine (QE)
version, some operations done at probe() need to be done in a different
order.
In order to prepare the support for the QE version, changed the sequence
of operation done at probe():
- Retrieve the tsa_serial earlier, before initializing resources.
- Group SCC initialisation and do this initialization when it is really
needed in the probe() sequence.
Having the QE compatible sequence in the CPM1 version does not lead to
any issue and works correctly without any regressions.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-26-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles CPM1 version of QMC. Some hardcoded values are used
several times to initialize the QMC state machine. In the QUICC Engine
(QE) version of QMC, these values are different.
In order to prepare the support for the QE version of QMC and avoid the
copy of the hardcoded values, introduce the qmc_data structure to define
these version specific values.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-25-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Add support for the QMC (QUICC Multichannel Controller) available in
some PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321.
This QE QMC is similar to the CPM QMC except that it uses UCCs (Unified
Communication Controllers) instead of SCCs (Serial Communication
Controllers). Also, compared against the CPM QMC, this QE QMC does not
use a fixed area for the UCC/SCC parameters area but it uses a dynamic
area allocated and provided to the hardware at runtime.
Last point, the QE QMC can use a firmware to have the QMC working in
'soft-qmc' mode.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-24-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
checkpatch.pl signals the following improvement for qmc.c
CHECK: Prefer using the BIT macro
Follow its suggestion and convert the code to BIT() and related macros.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-19-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
QMC_TSA_MASK is a bitfield. The value defined is a specific value of
this bitfield and correspond to the use of 8bit resolution for the
routing entry.
Be accurate and rename the defined constant to reflect this point.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-18-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
TSA consumers in CPM1 implementation don't need to know about the serial
device number used by the TSA component. In QUICC Engine implementation,
this information is needed.
Improve the TSA API with tsa_serial_get_num() in order to provide this
information.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-17-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The Freescale TSA controller driver supports both QE and CPM1.
Add the newly introduced QE files to the existing entry.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-16-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Add support for the time slot assigner (TSA) available in some
PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321.
The QE TSA is similar to the CPM1 TSA except that it uses UCCs (Unified
Communication Controllers) instead of SCCs (Serial Communication
Controllers).
Also, compared against the CPM1 TSA, this QE TSA can handle up to 4 TDMs
instead of 2 and allows to configure the logic level of sync signals.
At a lower level, compared against CPM TSA implementation, some
registers are slightly different even if same features are present.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-15-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles CPM1 version of TSA.
In order to prepare the support for the QUICC Engine (QE) version of
TSA, introduce tsa_version to identify versions. This will enable the
code to make the distinction between several TSA implementations.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-14-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of TSA. Connecting and
disconnecting the SCC to/from the TSA consists in handling SICR register
which is CPM1 specific. The connection and disconnection operation in
the QUICC Engine (QE) version are slightly different.
In order to prepare the support for the QE version, clearly identify
SICR register as specific to CPM1 and isolate its handling done in
connect and disconnect functions.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-13-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of TSA. Setting up TSA consists in
handling SIMODE and SIGMR registers. These registers are CPM1 specific.
Setting up the QUICC Engine (QE) version of TSA is slightly different.
In order to prepare the support for QE version, clearly identify these
registers as CPM1 compatible and isolate their handling in a CPM1
specific function.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-12-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Current code handles the CPM1 version of TSA. Compared against QUICC
Engine (QE) version of TSA, CPM1 SIRAM entries are slightly different.
In order to prepare the support for the QE version, clearly identify
these entries and functions handling them as CPM1 compatible.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-11-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Loops handling the tdm array use hardcoded size and the initialization
part uses hardcoded indexes to initialize the array.
Use ARRAY_SIZE() to avoid the hardcoded size and initialize the array
using a loop.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-10-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Add support for the time slot assigner (TSA) available in some
PowerQUICC SoC that uses a QUICC Engine (QE) block such as MPC8321.
This QE TSA is similar to the CPM TSA except that it uses UCCs (Unified
Communication Controllers) instead of SCCs (Serial Communication
Controllers). Also, compared against the CPM TSA, this QE TSA can handle
up to 4 TDMs instead of 2 and allows to configure the logic level of
sync signals.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-8-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
checkpatch.pl signals the following improvement for tsa.c
CHECK: Prefer using the BIT macro
Follow its suggestion and convert the code to BIT() and related macros.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-5-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The tsa_write8() parameter is an u32 value. This is not consistent with
the function itself. Indeed, tsa_write8() writes an 8bits value.
Be consistent and use an u8 parameter value.
Fixes: 1d4ba0b81c ("soc: fsl: cpm1: Add support for TSA")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-4-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The TRNSYNC feature is enabled whatever the number of time-slots used.
The feature is needed only when more than one time-slot is used.
Improve the driver enabling TRNSYNC only when it is needed.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-3-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
The TRNSYNC feature is available (and enabled) only in transparent mode.
Since commit 7cc9bda9c1 ("soc: fsl: cpm1: qmc: Handle timeslot entries
at channel start() and stop()") TRNSYNC register is updated in
transparent and hdlc mode. In hdlc mode, the address of the TRNSYNC
register is used by the QMC for other internal purpose. Even if no weird
results were observed in hdlc mode, touching this register in this mode
is wrong.
Update TRNSYNC only in transparent mode.
Fixes: 7cc9bda9c1 ("soc: fsl: cpm1: qmc: Handle timeslot entries at channel start() and stop()")
Cc: stable@vger.kernel.org
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20240808071132.149251-2-herve.codina@bootlin.com
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Since commit 946fa0dbf2 ("mm/slub: extend redzone check to extra
allocated kmalloc space than requested"), setting orig_size treats
the wasted space (object_size - orig_size) as a redzone. However with
init_on_free=1 we clear the full object->size, including the redzone.
Additionally we clear the object metadata, including the stored orig_size,
making it zero, which makes check_object() treat the whole object as a
redzone.
These issues lead to the following BUG report with "slub_debug=FUZ
init_on_free=1":
[ 0.000000] =============================================================================
[ 0.000000] BUG kmalloc-8 (Not tainted): kmalloc Redzone overwritten
[ 0.000000] -----------------------------------------------------------------------------
[ 0.000000]
[ 0.000000] 0xffff000010032858-0xffff00001003285f @offset=2136. First byte 0x0 instead of 0xcc
[ 0.000000] FIX kmalloc-8: Restoring kmalloc Redzone 0xffff000010032858-0xffff00001003285f=0xcc
[ 0.000000] Slab 0xfffffdffc0400c80 objects=36 used=23 fp=0xffff000010032a18 flags=0x3fffe0000000200(workingset|node=0|zone=0|lastcpupid=0x1ffff)
[ 0.000000] Object 0xffff000010032858 @offset=2136 fp=0xffff0000100328c8
[ 0.000000]
[ 0.000000] Redzone ffff000010032850: cc cc cc cc cc cc cc cc ........
[ 0.000000] Object ffff000010032858: cc cc cc cc cc cc cc cc ........
[ 0.000000] Redzone ffff000010032860: cc cc cc cc cc cc cc cc ........
[ 0.000000] Padding ffff0000100328b4: 00 00 00 00 00 00 00 00 00 00 00 00 ............
[ 0.000000] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.11.0-rc3-next-20240814-00004-g61844c55c3f4 #144
[ 0.000000] Hardware name: NXP i.MX95 19X19 board (DT)
[ 0.000000] Call trace:
[ 0.000000] dump_backtrace+0x90/0xe8
[ 0.000000] show_stack+0x18/0x24
[ 0.000000] dump_stack_lvl+0x74/0x8c
[ 0.000000] dump_stack+0x18/0x24
[ 0.000000] print_trailer+0x150/0x218
[ 0.000000] check_object+0xe4/0x454
[ 0.000000] free_to_partial_list+0x2f8/0x5ec
To address the issue, use orig_size to clear the used area. And restore
the value of orig_size after clear the remaining area.
When CONFIG_SLUB_DEBUG not defined, (get_orig_size()' directly returns
s->object_size. So when using memset to init the area, the size can simply
be orig_size, as orig_size returns object_size when CONFIG_SLUB_DEBUG not
enabled. And orig_size can never be bigger than object_size.
Fixes: 946fa0dbf2 ("mm/slub: extend redzone check to extra allocated kmalloc space than requested")
Cc: <stable@vger.kernel.org>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Currently there is no way to apply quirk on device only if certain panel
model is installed. This patch implements such mechanism by adding new
quirk type intel_dpcd_quirk which contains also sink_oui and sink_device_id
fields and using also them to figure out if applying quirk is needed.
New intel_init_dpcd_quirks is added and called after drm_dp_read_desc with
proper sink device identity read from dpcdc.
v3:
- !mem_is_zero fixed to mem_is_zero
v2:
- instead of using struct intel_quirk add new struct intel_dpcd_quirk
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902064241.1020965-2-jouni.hogander@intel.com
COW writes remove the amount overwritten either directly for delalloc
reservations, or in earlier deferred transactions than adding the new
amount back in the bmap map transaction. This means st_blocks on an
inode where all data is overwritten using the COW path can temporarily
show a 0 st_blocks. This can easily be reproduced with the pending
zoned device support where all writes use this path and trips the
check in generic/615, but could also happen on a reflink file without
that.
Fix this by temporarily add the pending blocks to be mapped to
i_delayed_blks while the item is queued.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
xfs_reclaim_inodes_count iterates over all AGs to sum up the reclaimable
inodes counts. There is no point in grabbing a reference to the them or
unlock the RCU critical section for each iteration, so switch to the
more efficient xas_for_each_marked iterator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
