The guest recovery sequence is buggy in Fatal Error when both
FLR & KFD reset workitems are queued at the same time. In addition,
FLR guest recovery sequence is out of order when PF/VF communication
breaks due to a GPU fatal error
As a temporary work around, perform a KFD style reset (Initiate reset
request from the guest) inside the pf2vf thread on FED.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Runtime KIQ interface to read/write registers in VF may take longer
than expected for BM environment. Extend the timeout.
Signed-off-by: Victor Skvortsov <victor.skvortsov@amd.com>
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version pairs with DMUB FW Release 0.0.218.0 for dcn314/315/316, dcn35/351, dcn401
and brings along the following:
- Fix powerpc compilation
- Fix TBT+TypeC Daisy-chain lightup
- Fix ODM combine setup
- Fix OTC underflow on dcn35
- Fix DVI config for dcn401
- Add ips status info to debugfs
- Add 3DLUT DMA load trigger
- Modify clock programming to support DPM
- Disable dcn401 idle optimizations
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Compilation errors while compiling without CONFIG_DRM_AMD_DC_FP:
"undefined reference to `dc_bandwidth_in_kbps_from_timing'"
[How]
Fix Makefile to move dsc files out of DC_FP guard.
Fixes: 00c391102a ("drm/amd/display: Add misc DC changes for DCN401")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the link BW is smaller than the request BW,
the DP LT just kept running and fallback to lower link config.
DP LT just aborted if is_hpd_pending bit is high.
But is_hpd_pending bit indicates a new HPD event received.
It doesn't mean the HPD is low.
[How]
Abort the DP LT if the link BW is smaller than the request BW.
Remove checking is_hpd_pending bit in DP LT.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Cruise <cruise.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
At the time of block sequence construction, the exact reference DPP/DISP clock is
not yet known, so the clock should be passed by reference to the DTO programming
function.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
Disable to improve stability for now.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
There is a corner case where we're in an ODM config that
has recout.x != 0. In these scenarios we have to take into
account the extra offset in the ODM adjustment for cursor.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A recent change for ODM combine refactor contains a typo which causes ODM
combine mode programmed incorrectly.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable idle optimization for each atomic commit is unnecessary,
and can lead to a potential race condition.
[How]
Remove idle optimization check from amdgpu_dm_atomic_commit_tail()
Fixes: 196107eb1e ("drm/amd/display: Add IPS checks before dcn register access")
Cc: stable@vger.kernel.org
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Missing check for when there is new pipe configuration but both cur_pipe
and new_pipe are both populated causing update_state of DSC for that
instance not being updated correctly.
This causes some display mode changes to cause underflow since DSCCLK
is still gated when the display requires DSC.
[How]
Added another condition in the new pipe addition branch that checks if
there is a new pipe configuration and if it is not the same as cur_pipe.
cur_pipe does not necessarily have to be NULL to go in this branch.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging and testing purposes.
[How]
If IPS is supported create ips_status debugfs entry.
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_ips_status
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reset the shared dmub firmware region on dmub hw init to start with
known state.
[How]
Memset the shared region to 0 in dmub_hw_init().
Suggested-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Need to be able to trigger a DMA load to update 3DLUT contents in MPC.
Adding a HWSS function to serve as the trigger.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML 2.1 allocates two types of memory in its ctx structure but does not
destroy them, causing memory leak whenever DML 2.1 instance is created
and destroyed.
[How]
Deallocate two instances of allocated memory whenever DML 2.1 is
destroyed.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
update driver-if interface for smu 14.0.2/3
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to select DTBCLK and DPREFCLK as DTBCLK_p source according to
hardware guidance.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Cleaning up the code refactor requires hubbub to be in its own
component.
[how]
Move all DCN401 files under newly created hubbub folder and fixing the
makefiles.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Harikrishna Revalla <Harikrishna.Revalla@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable adaptive scaler support for DCN401
[How]
- Enable build flag for SPL
- Set prefer_easf flag to true
- Apply light linear scaling policy based on transfer function and pixel
format. Choose between linear or non-linear scaling
- Set matrix_mode based on pixel format
- Disable ring estimator
- Add missing EASF register defines, masks, and writes
- Disable EASF if scale ratio or number of taps is unsupported and when
bypassing the scaler
- Add debug flags and registry keys for debugging SPL and EASF
- Add support for Visual Confirm with EASF
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes indentations and adjust spaces for better readability and
code styles.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DVI is TMDS signal like HDMI but without audio. Current signal check
does not correctly reflect DVI clock programming.
[How]
Define a new signal check for TMDS that includes DVI to HDMI TMDS
programming.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The comparisons intend to be DCN401 inclusive, and fix it by adding
equal signs.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The functions are missing. These two functions are required to support
MST.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function that commits planes calls the same set of functions twice,
and in the case of the FAMs utilization, it is not desired to call the
dmub, hwss_build and hwss_execute. This commit just removes the
unnecessary calls to those functions.
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move dsc functions from dc.c to dc_dsc.c.
Co-developed-by: George Shen <george.shen@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Introduce Parent Pointer extended attribute for inodes.
* Online Repair
- Implement atomic file content exchanges i.e. exchange ranges of bytes
between two files atomically.
- Create temporary files to repair file-based metadata. This uses atomic
file content exchange facility to swap file fork mappings between the
temporary file and the metadata inode.
- Allow callers of directory/xattr code to set an explicit owner number to
be written into the header fields of any new blocks that are created.
This is required to avoid walking every block of the new structure and
modify their ownership during online repair.
- Repair
- Extended attributes
- Inode unlinked state
- Directories
- Symbolic links
- AGI's unlinked inode list.
- Parent pointers.
- Move Orphan files to lost and found directory.
- Fixes for Inode repair functionality.
- Introduce a new sub-AG FITRIM implementation to reduce the duration for
which the AGF lock is held.
- Updates for the design documentation.
- Use Parent Pointers to assist in checking directories, parent pointers,
extended attributes, and link counts.
* Bring back delalloc support for realtime devices which have an extent size
that is equal to filesystem's block size.
* Improve performance of log incompat feature handling.
* Fixes
- Prevent userspace from reading invalid file data due to incorrect.
updation of file size when performing a non-atomic clone operation.
- Minor fixes to online repair.
- Fix confusing return values from xfs_bmapi_write().
- Fix an out of bounds access due to incorrect h_size during log recovery.
- Defer upgrading the extent counters in xfs_reflink_end_cow_extent() until
we know we are going to modify the extent mapping.
- Remove racy access to if_bytes check in xfs_reflink_end_cow_extent().
- Fix sparse warnings.
* Cleanups
- Hold inode locks on all files involved in a rename until the completion
of the operation. This is in preparation for the parent pointers patchset
where parent pointers are applied in a separate chained update from the
actual directory update.
- Compile out v4 support when disabled.
- Cleanup xfs_extent_busy_clear().
- Remove unused flags and fields from struct xfs_da_args.
- Remove definitions of unused functions.
- Improve extended attribute validation.
- Add higher level directory operations helpers to remove duplication of
code.
- Cleanup quota (un)reservation interfaces.
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQjMC4mbgVeU7MxEIYH7y4RirJu9AUCZjZC0wAKCRAH7y4RirJu
9HsCAPoCQvmPefDv56aMb5JEQNpv9dPz2Djj14hqLytQs5P/twD+LF5NhJgQNDUo
Lwnb0tmkAhmG9Y4CCiN1FwSj1rq59gE=
=2hXB
-----END PGP SIGNATURE-----
Merge tag 'xfs-6.10-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs updates from Chandan Babu:
"Online repair feature continues to be expanded. Also, we now support
delayed allocation for realtime devices which have an extent size that
is equal to filesystem's block size.
New code:
- Introduce Parent Pointer extended attribute for inodes
- Bring back delalloc support for realtime devices which have an
extent size that is equal to filesystem's block size
- Improve performance of log incompat feature handling
Online Repair:
- Implement atomic file content exchanges i.e. exchange ranges of
bytes between two files atomically
- Create temporary files to repair file-based metadata. This uses
atomic file content exchange facility to swap file fork mappings
between the temporary file and the metadata inode
- Allow callers of directory/xattr code to set an explicit owner
number to be written into the header fields of any new blocks that
are created. This is required to avoid walking every block of the
new structure and modify their ownership during online repair
- Repair more data structures:
- Extended attributes
- Inode unlinked state
- Directories
- Symbolic links
- AGI's unlinked inode list
- Parent pointers
- Move Orphan files to lost and found directory
- Fixes for Inode repair functionality
- Introduce a new sub-AG FITRIM implementation to reduce the duration
for which the AGF lock is held
- Updates for the design documentation
- Use Parent Pointers to assist in checking directories, parent
pointers, extended attributes, and link counts
Fixes:
- Prevent userspace from reading invalid file data due to incorrect.
updation of file size when performing a non-atomic clone operation
- Minor fixes to online repair
- Fix confusing return values from xfs_bmapi_write()
- Fix an out of bounds access due to incorrect h_size during log
recovery
- Defer upgrading the extent counters in xfs_reflink_end_cow_extent()
until we know we are going to modify the extent mapping
- Remove racy access to if_bytes check in
xfs_reflink_end_cow_extent()
- Fix sparse warnings
Cleanups:
- Hold inode locks on all files involved in a rename until the
completion of the operation. This is in preparation for the parent
pointers patchset where parent pointers are applied in a separate
chained update from the actual directory update
- Compile out v4 support when disabled
- Cleanup xfs_extent_busy_clear()
- Remove unused flags and fields from struct xfs_da_args
- Remove definitions of unused functions
- Improve extended attribute validation
- Add higher level directory operations helpers to remove duplication
of code
- Cleanup quota (un)reservation interfaces"
* tag 'xfs-6.10-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (221 commits)
xfs: simplify iext overflow checking and upgrade
xfs: remove a racy if_bytes check in xfs_reflink_end_cow_extent
xfs: upgrade the extent counters in xfs_reflink_end_cow_extent later
xfs: xfs_quota_unreserve_blkres can't fail
xfs: consolidate the xfs_quota_reserve_blkres definitions
xfs: clean up buffer allocation in xlog_do_recovery_pass
xfs: fix log recovery buffer allocation for the legacy h_size fixup
xfs: widen flags argument to the xfs_iflags_* helpers
xfs: minor cleanups of xfs_attr3_rmt_blocks
xfs: create a helper to compute the blockcount of a max sized remote value
xfs: turn XFS_ATTR3_RMT_BUF_SPACE into a function
xfs: use unsigned ints for non-negative quantities in xfs_attr_remote.c
xfs: do not allocate the entire delalloc extent in xfs_bmapi_write
xfs: fix xfs_bmap_add_extent_delay_real for partial conversions
xfs: remove the xfs_iext_peek_prev_extent call in xfs_bmapi_allocate
xfs: pass the actual offset and len to allocate to xfs_bmapi_allocate
xfs: don't open code XFS_FILBLKS_MIN in xfs_bmapi_write
xfs: lift a xfs_valid_startblock into xfs_bmapi_allocate
xfs: remove the unusued tmp_logflags variable in xfs_bmapi_allocate
xfs: fix error returns from xfs_bmapi_write
...
Commit 4f563a6473 ("block: add a max_user_discard_sectors queue
limit") changed block core to set max_discard_sectors to:
min(lim->max_hw_discard_sectors, lim->max_user_discard_sectors)
Since commit 1c0e720228 ("dm: use queue_limits_set") it was reported
dm-thinp was failing in a few fstests (generic/347 and generic/405)
with the first WARN_ON_ONCE in dm_cell_key_has_valid_range() being
reported, e.g.:
WARNING: CPU: 1 PID: 30 at drivers/md/dm-bio-prison-v1.c:128 dm_cell_key_has_valid_range+0x3d/0x50
blk_set_stacking_limits() sets max_user_discard_sectors to UINT_MAX,
so given how block core now sets max_discard_sectors (detailed above)
it follows that blk_stack_limits() stacks up the underlying device's
max_hw_discard_sectors and max_discard_sectors is set to match it. If
max_hw_discard_sectors exceeds dm's BIO_PRISON_MAX_RANGE, then
dm_cell_key_has_valid_range() will trigger the warning with:
WARN_ON_ONCE(key->block_end - key->block_begin > BIO_PRISON_MAX_RANGE)
Aside from this warning, the discard will fail. Fix this and other DM
issues by governing discard support in terms of max_hw_discard_sectors
instead of max_discard_sectors.
Reported-by: Theodore Ts'o <tytso@mit.edu>
Fixes: 1c0e720228 ("dm: use queue_limits_set")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmZLMxUACgkQnJ2qBz9k
QNnnXAgA1MfUPm6b4AE3y3EEWUSTQd2THQSGUg/ZLeJW3zE5nNaW74BPYKTSTreY
Bmx0QVrgzJX9EJe2UmFsnPiPEzznn1RIDdPwCQEZpjEt+/iX3/+5+z+aDK57mWpJ
5Lxzv/Ji1iNlYzdDti8MIc9edj923A7JpQQQ7Hz6ldmuc5EHXLrcTTzytPIDU5cp
6RKY7W0sntslTjKvVkZaEqugPtQpe064Sq7a0jtjLz2r+tyxDXakWNGrdQIYDTLR
UGwsFFZL5JbnR12oCMKJ3Vh3YjA5gmyxlbHCghDtGkXrSS1mseumJYsRFazE7y+8
Fp1fbObLe1z22N742r1aNE8vtXLGUw==
=nUBh
-----END PGP SIGNATURE-----
Merge tag 'fs_for_v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull isofs, udf, quota, ext2, and reiserfs updates from Jan Kara:
- convert isofs to the new mount API
- cleanup isofs Makefile
- udf conversion to folios
- some other small udf cleanups and fixes
- ext2 cleanups
- removal of reiserfs .writepage method
- update reiserfs README file
* tag 'fs_for_v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
isofs: Use *-y instead of *-objs in Makefile
ext2: Remove LEGACY_DIRECT_IO dependency
isofs: Remove calls to set/clear the error flag
ext2: Remove call to folio_set_error()
udf: Use a folio in udf_write_end()
udf: Convert udf_page_mkwrite() to use a folio
udf: Convert udf_symlink_getattr() to use a folio
udf: Convert udf_adinicb_readpage() to udf_adinicb_read_folio()
udf: Convert udf_expand_file_adinicb() to use a folio
udf: Convert udf_write_begin() to use a folio
udf: Convert udf_symlink_filler() to use a folio
reiserfs: Trim some README bits
quota: fix to propagate error of mark_dquot_dirty() to caller
reiserfs: Convert to writepages
udf: udftime: prevent overflow in udf_disk_stamp_to_time()
ext2: set FMODE_CAN_ODIRECT instead of a dummy direct_IO method
udf: replace deprecated strncpy/strcpy with strscpy
udf: Remove second semicolon
isofs: convert isofs to use the new mount API
fs: quota: use group allocation of per-cpu counters API
dm-integrity could set discard_granularity lower than the logical block
size. This could result in failures when sending discard requests to
dm-integrity.
This fix is needed for kernels prior to 6.10.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Eric Wheeler <linux-integrity@lists.ewheeler.net>
Cc: stable@vger.kernel.org # <= 6.9
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
This reverts commit e659522446.
These kinds of patches are only making the code worse.
Compilers don't care about the unnecessary check, but removing it makes
the code less obvious to a human. The declaration of 'len' is more than
80 lines earlier, so a human won't easily see that 'len' is of an
unsigned type, so to a human the range check that checks against zero is
much more explicit and obvious.
Any tool that complains about a range check like this just because the
variable is unsigned is actively detrimental, and should be ignored.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Performance Counters enum used to identify the index of each
performance counter and provide the total number of performance
counters (V3D_PERFCNT_NUM). But, this enum is only valid for V3D 4.2,
not for V3D 7.1.
As we implemented a new flexible structure to retrieve performance
counters information, we can deprecate this enum.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-7-mcanal@igalia.com
V3D_PERFCNT_NUM represents the maximum number of performance counters
for V3D 4.2, but not for V3D 7.1. This means that, if we use
V3D_PERFCNT_NUM, we might go out-of-bounds on V3D 7.1.
Therefore, use the number of performance counters on V3D 7.1 as the
maximum number of counters. This will allow us to create arrays on the
stack with reasonable size. Note that userspace must use the value
provided by DRM_V3D_PARAM_MAX_PERF_COUNTERS.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-6-mcanal@igalia.com
Userspace usually needs some information about the performance counters
available. Although we could replicate this information in the kernel
and user-space, let's use the kernel as the "single source of truth" to
avoid issues in the future (e.g. list of performance counters is updated
in user-space, but not in the kernel, generating invalid requests).
Therefore, create a new IOCTL to expose the performance counters
information, that is name, category, and description.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-5-mcanal@igalia.com
The maximum number of performance counters can change from version to
version and it's important for userspace to know this value, as it needs
to use the counters for performance queries. Therefore, expose the
maximum number of performance counters to userspace as a parameter.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-4-mcanal@igalia.com
Currently, even though V3D 7.1 has 93 performance counters, it is not
possible to create counters bigger than 87, as
`v3d_perfmon_create_ioctl()` understands that counters bigger than 87
are invalid.
Therefore, create a device variable to expose the maximum
number of counters for a given V3D version and make
`v3d_perfmon_create_ioctl()` check this variable.
This commit fixes CTS failures in the performance queries tests
`dEQP-VK.query_pool.performance_query.*` [1]
Link: ea1f09a5f2 [1]
Fixes: 6fd9487147 ("drm/v3d: add brcm,2712-v3d as a compatible V3D device")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-3-mcanal@igalia.com
Add name, category and description for each one of the 93 performance
counters available on V3D.
Note that V3D 4.2 has 87 performance counters, while V3D 7.1 has 93.
Therefore, there are two performance counters arrays. The index of the
performance counter for each V3D version is represented by its position
on the array.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240512222655.2792754-2-mcanal@igalia.com
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmZLJS0ACgkQnJ2qBz9k
QNmFlggAlIg5oDZfOhJur6h3Icldrl2DsnKer0CAP7TFK+GfkFTEb25paoydBEu4
Y0VzZ3n3EqhmsJ8P515k1UPPPXlqqZwSRWGAek0FDhQCXhqEYxiWwf9U343hJNBS
rya4Rnwc1pxqmJU2hrY5R5kEbugUFAIL+qNXzhhLpWonYiy/ya7P5n/qz5F5HJH2
FufRRaPHcHFfk1u0+PvFrk019AS9C6Y3bkcUGtbpdwmFsuN3D4HKuLEkr1+C9Apb
NmkoAwCiSobQhAxGDr6Szqu6r1VCuM+n/O9fqLknnL9u0jm95AmGdIMOdQ/ofx6d
xn3mfRp8gUbPD8PubHhQsMjCmSjGwg==
=kwWW
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
- reduce overhead of fsnotify infrastructure when no permission events
are in use
- a few small cleanups
* tag 'fsnotify_for_v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: fix UAF from FS_ERROR event on a shutting down filesystem
fsnotify: optimize the case of no permission event watchers
fsnotify: use an enum for group priority constants
fsnotify: move s_fsnotify_connectors into fsnotify_sb_info
fsnotify: lazy attach fsnotify_sb_info state to sb
fsnotify: create helper fsnotify_update_sb_watchers()
fsnotify: pass object pointer and type to fsnotify mark helpers
fanotify: merge two checks regarding add of ignore mark
fsnotify: create a wrapper fsnotify_find_inode_mark()
fsnotify: create helpers to get sb and connp from object
fsnotify: rename fsnotify_{get,put}_sb_connectors()
fsnotify: Avoid -Wflex-array-member-not-at-end warning
fanotify: remove unneeded sub-zero check for unsigned value
s/does not use unnecessary/do not unnecessarily use/
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Most of the people prefer:
return ret < 0 ? ret: 0;
than:
return min(ret, 0);
Let's tweak the cocci file to ignore those lines completely.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
The data-sheet for TPS6287x-Q1
https://www.ti.com/lit/ds/symlink/tps62873-q1.pdf
states at chapter 9.3.6.1 Output Voltage Range:
"Note that every change to the VRANGE[1:0] bits must be followed by a
write to the VSET register, even if the value of the VSET[7:0] bits does
not change."
The current implementation of the driver uses the
regulator_set_voltage_sel_pickable_regmap() helper which further uses
regmap_update_bits() to write the VSET-register. The
regmap_update_bits() will not access the hardware if the new register
value is same as old. It is worth noting that this is true also when the
register is marked volatile, which I can't say is wrong because
'read-mnodify-write'-cycle with a volatile register is in any case
something user should carefully consider.
The 'range_applied_by_vsel'-flag in regulator desc was added to force
the vsel register upodates by using regmap_write_bits(). This variant
will always unconditionally write the bits to the hardware.
It is worth noting that the vsel is now forced to be written to the
hardware, whether the range was changed or not. This may cause a
performance drop if users are wrtiting same voltage value repeteadly.
It would be possible to read the range register to determine if it was
changed, but this would be a performance issue for users who don't use
reg cache for vsel.
Always write the VSET register to the hardware regardless the cache.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 7b0518fbf2 ("regulator: Add support for TI TPS6287x regulators")
Link: https://msgid.link/r/ZktD50C5twF1EuKu@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, each DEFLATE stream takes one 32 KiB permanent internal
window buffer even if there is no running instance which uses DEFLATE
algorithm.
It's unexpected and wasteful on embedded devices with limited resources
and servers with hundreds of CPU cores if DEFLATE is enabled but unused.
Fixes: ffa09b3bd0 ("erofs: DEFLATE compression support")
Cc: <stable@vger.kernel.org> # 6.6+
Reviewed-by: Sandeep Dhavale <dhavale@google.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20240520090106.2898681-1-hsiangkao@linux.alibaba.com
Revert f6ae9f120d ("netfilter: nft_payload: add C-VLAN support").
f41f72d09e ("netfilter: nft_payload: simplify vlan header handling")
already allows to match on inner vlan tags by subtract the vlan header
size to the payload offset which has been popped and stored in skbuff
metadata fields.
Fixes: f6ae9f120d ("netfilter: nft_payload: add C-VLAN support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Flushing list in cancel_gc drops references to other lists right away,
without waiting for RCU to destroy list. Fixes race when referenced
ipsets can't be destroyed while referring list is scheduled for destroy.
Fixes: 97f7cf1cd8 ("netfilter: ipset: fix performance regression in swap operation")
Signed-off-by: Alexander Maltsev <keltar.gw@gmail.com>
Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some PMICs treat the vsel_reg same as apply-bit. Eg, when voltage range
is changed, the new voltage setting is not taking effect until the vsel
register is written.
Add a flag 'range_applied_by_vsel' to the regulator desc to indicate this
behaviour and to force the vsel value to be written to hardware if range
was changed, even if the old selector was same as the new one.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://msgid.link/r/ZktCpcGZdgHWuN_L@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
-----BEGIN PGP SIGNATURE-----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=Pa8W
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- optimize DMA sync calls when they are no-ops (Alexander Lobakin)
- fix swiotlb padding for untrusted devices (Michael Kelley)
- add documentation for swiotb (Michael Kelley)
* tag 'dma-mapping-6.10-2024-05-20' of git://git.infradead.org/users/hch/dma-mapping:
dma: fix DMA sync for drivers not calling dma_set_mask*()
xsk: use generic DMA sync shortcut instead of a custom one
page_pool: check for DMA sync shortcut earlier
page_pool: don't use driver-set flags field directly
page_pool: make sure frag API fields don't span between cachelines
iommu/dma: avoid expensive indirect calls for sync operations
dma: avoid redundant calls for sync operations
dma: compile-out DMA sync op calls when not used
iommu/dma: fix zeroing of bounce buffer padding used by untrusted devices
swiotlb: remove alloc_size argument to swiotlb_tbl_map_single()
Documentation/core-api: add swiotlb documentation
* KCFI violation fix for dmi-id.
* Stop decoding on broken (short) DMI table entry.
* Print info about populated memory slots at boot.
-----BEGIN PGP SIGNATURE-----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=088k
-----END PGP SIGNATURE-----
Merge tag 'dmi-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull dmi updates from Jean Delvare:
"Bug fixes:
- KCFI violation in dmi-id
- stop decoding on broken (short) DMI table entry
New features:
- print info about populated memory slots at boot"
* tag 'dmi-for-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
firmware: dmi: Add info message for number of populated and total memory slots
firmware: dmi: Stop decoding on broken entry
firmware: dmi-id: add a release callback function
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmZLZDUACgkQ+iyteGJfRspfLwCfQ9zpNL4pAPdjG8bS8OKYSmeU
OUAAnR28y57NBUsnA456Uqqv+dBc44vb
=NBPL
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-6.10-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Lenovo SE10 platform Watchdog Driver
- Other small fixes and improvements
* tag 'linux-watchdog-6.10-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: LENOVO_SE10_WDT should depend on X86 && DMI
watchdog: sa1100: Fix PTR_ERR_OR_ZERO() vs NULL check in sa1100dog_probe()
watchdog: rti_wdt: Set min_hw_heartbeat_ms to accommodate a safety margin
watchdog: add HAS_IOPORT dependencies
watchdog/wdt-main: Use cpumask_of() to avoid cpumask var on stack
watchdog: bd9576: Drop "always-running" property
watchdog: mtx-1: drop driver owner assignment
watchdog: cpu5wdt.c: Fix use-after-free bug caused by cpu5wdt_trigger
watchdog: lenovo_se10_wdt: Watchdog driver for Lenovo SE10 platform
