ret is assigned return value of event_hist_trigger_func, but the value
is unused. It is better to warn when returned value is negative,
rather than just ignoring it.
Link: https://lkml.kernel.org/r/20210529061423.GA103954@hyeyoo
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The variable ret is being initialized with a value that is never read,
it is being updated later on. The assignment is redundant and can be
removed.
Link: https://lkml.kernel.org/r/20210513115517.58178-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Variable event_var is set to 'ERR_PTR(-EINVAL)', but this value
is never read as it is overwritten or not used later on, hence
it is a redundant assignment and can be removed.
Clean up the following clang-analyzer warning:
kernel/trace/trace_events_hist.c:2437:21: warning: Value stored to
'event_var' during its initialization is never read
[clang-analyzer-deadcode.DeadStores].
Link: https://lkml.kernel.org/r/1620470236-26562-1-git-send-email-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
'success' is left here for a long time and also it is meaningless
for the upper user. Just remove it.
[ There were some tools expecting this, and this may break them. But
hopefully they've been fixed in the mean time. Otherwise this may be
likely reverted - SDR ]
Link: https://lkml.kernel.org/r/20210422122226.9415-1-ed.tsai@mediatek.com
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ed Tsai <ed.tsai@mediatek.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
It is not necessary to define the variable ret to receive
the return value of the xbc_node_compose_key() method.
Link: https://lkml.kernel.org/r/20210414134647.1870-1-zuoqilin1@163.com
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: zuoqilin <zuoqilin@yulong.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
APER does not mean anything, while it seems legitimate to call this
clock the AXI peripheral clock.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210610082040.2075611-14-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
There is no point in having all these definitions at the SMC bus level,
these are extremely tight to the NAND controller driver implementation,
are not particularly generic, imply more boilerplate than needed, do
not really follow the device model by receiving no argument and some of
them are actually buggy.
Let's get rid of these right now as there is no current user and keep
this driver at a simple level: only the SMC bare initializations.
The NAND controller driver which I am going to introduce will take care
of redefining properly all these helpers and using them directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210610082040.2075611-13-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
A goto label is better named
do_something:
than
out_something_to_do:
Use the former wording and really describe what the jump involves.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210610082040.2075611-12-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
To be fully valid, the NAND controller node in the example should be
named nand-controller instead of flash, should be at the address @0,0
instead of @e1000000 and should have a couple of:
- #address-cells
- #size-cells
properties.
The label is being renamed nfc0 as well which is more usual than nand_0.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-8-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
These nodes are given as examples and are not described nor used
anywhere else. There is also no hardware of my knowledge compatible with
these yet. If we want to be backward compatible, then we should avoid
partially describing nodes and their content while there are no users.
Plus, the examples are wrong (the addresses should be updated) so
let's drop them before converting this file to yaml (only the NAND node,
which will be fixed in the example and described somewhere else is
kept).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-7-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Each chil node should have a reg property, no matter the type of
controller (NAND, NOR, SRAM). This should be part of the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-5-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This sentence does not belong to this file as this file describes the
bus on which various controllers are wired to.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-4-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The ranges property is missing in the description while actually used in
the example. This property is actually needed, so mention it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210610082040.2075611-3-miquel.raynal@bootlin.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).
A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.
Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.
Link: https://lore.kernel.org/r/20210609161509.9459-1-johan@kernel.org
Reported-by: David Frey <dpfrey@gmail.com>
Reported-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Tested-by: Alex Villacís Lasso <a_villacis@palosanto.com>
Fixes: f61309d9c9 ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc338 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc338 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
This spi flash part is actually being clocked at 37.5MHz, not 25MHz,
because of the way the clk driver is rounding up the rate that is
requested to the nearest supported frequency. Let's update the frequency
here, and remove the TODO because this is the fastest frequency we're
going to be able to use here.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210519054030.3217704-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-2-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This compatible string isn't present upstream. Let's drop the node as it
isn't used.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601185959.3101132-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't use the PON module on Trogdor devices. Instead the reboot
reason is sort of stored in the 'eventlog' and the bootloader figures
out if the boot is abnormal and records that there. Disable the PON node
and then drop the power key disabling because that's a child node that
will no longer be enabled if the PON node is disabled.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210601184417.3020834-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:
-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fix the following dtbs_check warning:
spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fix the following dtbs_check warning:
eth@1,0: $nodename:0: 'eth@1,0' does not match '^ethernet(@.*)?$'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fix the following dtbs_check warning:
touchscreen@38: 'linux,wakeup' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Introduce the VMID in the I/O path. Check if the VMID is enabled and if
the I/O belongs to a VM or not.
Link: https://lore.kernel.org/r/20210608043556.274139-14-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a periodic check for issuing of QFPA command and VMID timeout in the
worker thread. The inactivity timeout check is added via the timer
function.
Link: https://lore.kernel.org/r/20210608043556.274139-13-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement timeout functionality for the VMID. After the set time period of
inactivity, the VMID is deregistered from the switch.
Link: https://lore.kernel.org/r/20210608043556.274139-12-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the VMID in wqe before sending out the request. The type of VMID
depends on the configured type and is checked before being appended.
Link: https://lore.kernel.org/r/20210608043556.274139-11-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement CT commands for registering and deregistering the appid for the
application. Also, a small change in decrementing the ndlp ref counter has
been added.
Link: https://lore.kernel.org/r/20210608043556.274139-10-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement routines to save, retrieve, and remove the VMIDs from the data
structure. A hash table is used to save the VMIDs and the corresponding
UUIDs associated with the application/VMs.
Link: https://lore.kernel.org/r/20210608043556.274139-9-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement ELS commands QFPA and UVEM for the priority tagging appid
support.
Link: https://lore.kernel.org/r/20210608043556.274139-8-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add supporting datastructures for mailbox command which helps in
determining if the firmware supports appid. Allocate resources for VMID at
initialization time and clean them up on removal.
Link: https://lore.kernel.org/r/20210608043556.274139-7-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Initialize parameters such as type of VMID, max number of VMIDs supported
and timeout value for the VMID registration based on the user input.
Link: https://lore.kernel.org/r/20210608043556.274139-6-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the primary datastructures needed to implement VMID in the lpfc
driver. Maintain the capability, current state, and hash table for the
vmid/appid along with other information. This implementation supports the
two versions of vmid implementation (app header and priority tagging).
Link: https://lore.kernel.org/r/20210608043556.274139-5-muneendra.kumar@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gaurav Srivastava <gaurav.srivastava@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new sysfs attribute, appid_store, which can be used to set the
application identifier in the blkcg associated with a cgroup id.
Below is the interface provided to set the app_id:
echo "<cgroupid>:<appid>" >> /sys/class/fc/fc_udev_device/appid_store
echo "457E:100000109b521d27" >> /sys/class/fc/fc_udev_device/appid_store
Link: https://lore.kernel.org/r/20210608043556.274139-4-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a unique application identifier (i.e fc_app_id member) in blkcg. This
allows identification of traffic belonging to an specific both on the host
and in the fabric infrastructure. As an example, this allows the storage
stack to uniquely identify traffic belong to particular virtual machine.
Link: https://lore.kernel.org/r/20210608043556.274139-3-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new function, cgroup_get_from_id(), to retrieve the cgroup associated
with a cgroup id. Also export the function cgroup_get_e_css() as this is
needed in blk-cgroup.h.
Link: https://lore.kernel.org/r/20210608043556.274139-2-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define the clock outputs supported by RZ/G2L (R9A07G044) SoC
and bind it with RZ/G2L CPG core.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-10-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Clock definitions for the Renesas RZ/G2L (R9A07G044) SoC, shared by
driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYMIU6AAKCRCKwlD9ZEnx
cLTzAQDCHXUk8nXxbehYjdcDP7X3xEVh5OeZwSAKbwxKQvWtoQEAnlOysnT1LF0m
iNERFlisNuaR2hKXseifgf/7EIHRZQU=
=YzeJ
-----END PGP SIGNATURE-----
Merge tag 'renesas-r9a07g044-dt-binding-defs-tag' into renesas-clk-for-v5.14
Renesas RZ/G2L DT Binding Definitions
Clock definitions for the Renesas RZ/G2L (R9A07G044) SoC, shared by
driver and DT source files.
Add CPG core wrapper for RZ/G2L family.
Based on a patch in the BSP by Binh Nguyen
<binh.nguyen.jz@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210609153230.6967-9-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>