Under kdump environment we want to use the smallest possible amount
of resources, that includes setting SQ size to minimum.
However, when running on a device that supports TLS device offload,
then the SQ stop room becomes larger than with non-capable device and
requires increasing the SQ size.
Since TLS device offload is not necessary in kdump mode, disable it to
reduce the memory requirements for capable devices.
With this change, the needed SQ stop room size drops by 33.
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Under kdump environment we want to use the smallest possible amount
of resources, that includes setting SQ size to minimum.
However, when running on a device that supports TX MPWQE, then the SQ stop
room becomes larger than with non-capable device and requires increasing
the SQ size.
Since TX MPWQE offload is not necessary in kdump mode, disable it to
reduce the memory requirements for capable devices.
With this change, the needed SQ stop room size drops by 31.
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move the logic that updates the page pool upon changes in numa node.
Before this patch, logic was placed in the RX polling function, being
called also when no RX traffic, wasting cpu cycles. Here we move it to
the RX post_wqes function, to be called only when new RX descriptors are
going to be allocated.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Initialize structs to avoid unexpected behavior.
No immediate issue in current code, structs are return values, it's
safer to initialize.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add a check for if the kzalloc() fails.
Fixes: 4a98544d18 ("net/mlx5: Move chains ft pool to be used by all firmware steering")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Clean up the following includecheck warning:
./drivers/net/ethernet/mellanox/mlx5/core/sf/hw_table.c: vhca_event.h is
included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5 devices were observed generating MLX5_PORT_CHANGE_SUBTYPE_ACTIVE
events without an intervening MLX5_PORT_CHANGE_SUBTYPE_DOWN. This
breaks link flap detection based on Linux carrier state transition
count as netif_carrier_on() does nothing if carrier is already on.
Make sure we count such events.
netif_carrier_event() increments the counters and fires the linkwatch
events. The latter is not necessary for the use case but seems like
the right thing to do.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
To avoid the following failure when trying to load the rdma_rxe module
while IPv6 is disabled, add a check for EAFNOSUPPORT and ignore the
failure, also delete the needless debug print from rxe_setup_udp_tunnel().
$ modprobe rdma_rxe
modprobe: ERROR: could not insert 'rdma_rxe': Operation not permitted
Fixes: dfdd6158ca ("IB/rxe: Fix kernel panic in udp_setup_tunnel")
Link: https://lore.kernel.org/r/20210603090112.36341-1-kamalheib1@gmail.com
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The memory client IDs will subsequently be used to program override SIDs
for the given clients depending on the device tree configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-12-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The memory controller hot resets are implemented in the BPMP on Tegra186
and later, so there's no need to provide an implementation via the
memory controller driver. Conditionally register the reset controller
only if needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-10-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Separate the setup code for Tegra30 and later into a ->setup() callback
and set it for all applicable chips.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-7-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
This stable tag contains Dmitry's power domain work, including all the
necessary dependencies from the regulator, clock and ARM SoC trees.
-----BEGIN PGP SIGNATURE-----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=rx2q
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-memory' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into for-v5.14/tegra-mc
memory: tegra: Changes for v5.14-rc1
This stable tag contains Dmitry's power domain work, including all the
necessary dependencies from the regulator, clock and ARM SoC trees.
Further work depends on memory controller changes here.
The ac->state field is __le32, not u32. So change the variable we're
temporarily storing it in to __le32 as well.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e61ffb3445 ("power: supply: Add AC driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In order to prevent user space from modifying the index that belongs to
the kernel for shared queues let the kernel use a local copy of the index
and copy any new values of that index to the shared rxe_queue_bus struct.
This adds more switch statements which decreases the performance of the
queue API. Move the type into the parameter list for these functions so
that the compiler can optimize out the switch statements when the explicit
type is known. Modify all the calls in the driver on performance paths to
pass in the explicit queue type.
Link: https://lore.kernel.org/r/20210527194748.662636-4-rpearsonhpe@gmail.com
Link: https://lore.kernel.org/linux-rdma/20210526165239.GP1002214@@nvidia.com/
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Modify the queue APIs to protect all user space index loads with
smp_load_acquire() and all user space index stores with
smp_store_release(). Base this on the types of the queues which can be one
of ..KERNEL, ..FROM_USER, ..TO_USER. Kernel space indices are protected by
locks which also provide memory barriers.
Link: https://lore.kernel.org/r/20210527194748.662636-3-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
To create optimal code only want to use smp_load_acquire() and
smp_store_release() for user indices in rxe_queue APIs since kernel
indices are protected by locks which also act as memory barriers. By
adding a type to the queues we can determine which indices need to be
protected.
Link: https://lore.kernel.org/r/20210527194748.662636-2-rpearsonhpe@gmail.com
Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmC5BrwQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpq3tD/9FGANoxDDpLbQg/FCiK1pNoSf0EyoEWSdg
ysTF5KPAPC3msQOmuPYwRZfRFCkvtOHmrexPAZAaorCxEYPjiVAZ9b/a0hBC4Zc1
vVW8RcTp6hSonAp1kk6VgLEHulJMcLANjAx3Me3NDRB/g0KGW5gevqkUXIJ+nXiR
nqZcxaK7MD90v74IomO7y4P1GgwCbRhKYUL0JGQ4tXndYLxBYJnXBSnIKS2WdLZD
PCBf+TDDFAZeioueZ/GrXRhWBmy97j8sEKUJLRqjI5YG8VVZSofgPlwNBi1e42C8
l3ZEmXldyk18O8KDsZCI2E8axt62gLjuD7Tu6+gv0GBJTcdyXP/FaZYbkBMWjMBH
yq4Dk4QyJWfMFHJ886ukbGpwj1HJT1cJqzg4UUdkV3BlMNKtmZD8XrKTBw4HcPww
EmB+yywRiuH+XqamxPglFXUEOa4bJH/EAsQ0R5NNxAT/X/9iIOLUDBDAGvtWtBr0
7cz+7jTQchqmV11gN+JcgN2LvG14m6Xq4Xtv5oHhIy/FHbRCNPPrC7KJ22TOBSaD
d9mS5VM12+O9r9plYW7Cqdhdhnho/7/VfB+puiHg/lVcsXrMlrr0sc/WyrUixZeL
AUlhDtmoROcyFpdcA49LCBEFvacu13ivEstkxIonx997Ct4MW7joYds2YfHCfuoO
YlPVGdqeag==
=3m3m
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.13-2021-06-03' of git://git.kernel.dk/linux-block
Pull io_uring fix from Jens Axboe:
"Just a single one-liner fix for an accounting regression in this
release"
* tag 'io_uring-5.13-2021-06-03' of git://git.kernel.dk/linux-block:
io_uring: fix misaccounting fix buf pinned pages
-----BEGIN PGP SIGNATURE-----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=8066
-----END PGP SIGNATURE-----
Merge tag 'for-5.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Error handling improvements, caught by error injection:
- handle errors during checksum deletion
- set error on mapping when ordered extent io cannot be finished
- inode link count fixup in tree-log
- missing return value checks for inode updates in tree-log
- abort transaction in rename exchange if adding second reference
fails
Fixes:
- fix fsync failure after writes to prealloc extents
- fix deadlock when cloning inline extents and low on available space
- fix compressed writes that cross stripe boundary"
* tag 'for-5.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: add btrfs IRC link
btrfs: fix deadlock when cloning inline extents and low on available space
btrfs: fix fsync failure and transaction abort after writes to prealloc extents
btrfs: abort in rename_exchange if we fail to insert the second ref
btrfs: check error value from btrfs_update_inode in tree log
btrfs: fixup error handling in fixup_inode_link_counts
btrfs: mark ordered extent and inode with error if we fail to finish
btrfs: return errors from btrfs_del_csums in cleanup_ref_head
btrfs: fix error handling in btrfs_del_csums
btrfs: fix compressed writes that cross stripe boundary
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.
Changes in v5:
- Update spi_mem_read_status() description.
- Update poll_status() description API by indicating that data buffer is
filled with last status value.
- Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
- Remove parenthesys arount -EINVAL in spi_mem_poll_status().
- Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
- Add Boris Reviewed-by for patch 1 and 2.
Changes in v4:
- Remove init_completion() from spi_mem_probe() added in v2.
- Add missing static for spi_mem_read_status().
- Check if operation in spi_mem_poll_status() is a READ.
- Update patch 2 commit message.
- Add comment which explains how delays has been calculated.
- Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.
Chnages in v3:
- Add spi_mem_read_status() which allows to read 8 or 16 bits status.
- Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
and also to poll_status() callback.
- Move spi_mem_supports_op() in SW-based polling case.
- Add delay before invoquing read_poll_timeout().
- Remove the reinit/wait_for_completion() added in v2.
- Add initial_delay_us and polling_delay_us parameters to spinand_wait().
- Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
- Remove spi_mem_finalize_op() API added in v2.
Changes in v2:
- Indicates the spi_mem_poll_status() timeout unit
- Use 2-byte wide status register
- Add spi_mem_supports_op() call in spi_mem_poll_status()
- Add completion management in spi_mem_poll_status()
- Add offload/non-offload case management in spi_mem_poll_status()
- Optimize the non-offload case by using read_poll_timeout()
- mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
- Make usage of new spi_mem_finalize_op() API in
stm32_qspi_wait_poll_status()
Patrice Chotard (3):
spi: spi-mem: add automatic poll status functions
mtd: spinand: use the spi-mem poll status APIs
spi: stm32-qspi: add automatic poll status feature
drivers/mtd/nand/spi/core.c | 45 +++++++++++++------
drivers/spi/spi-mem.c | 86 ++++++++++++++++++++++++++++++++++++
drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
include/linux/mtd/spinand.h | 22 +++++++++
include/linux/spi/spi-mem.h | 16 +++++++
5 files changed, 234 insertions(+), 21 deletions(-)
base-commit: 6efb943b86
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Mark
I noticed that adg can be more clean code.
And rsnd.h header comment was not so good
because patch has been randomly added.
This patch tidyup these.
Kuninori Morimoto (5):
ASoC: rsnd: adg: supply __printf(x, y) formatting for dbg_msg()
ASoC: rsnd: adg: tidyup rsnd_adg_get_clkin/out() parameter
ASoC: rsnd: adg: use more simple method for null_clk
ASoC: rsnd: adg: check return value for rsnd_adg_get_clkin/out()
ASoC: rsnd: tidyup __rsnd_mod_xxx macro comments
sound/soc/sh/rcar/adg.c | 139 +++++++++++++++++++++++++--------------
sound/soc/sh/rcar/rsnd.h | 21 ++----
2 files changed, 97 insertions(+), 63 deletions(-)
--
2.25.1
Richtek RT6245 is a high-performance, synchronous step-down converter
that can deliver up to 14A output current with an input supply voltage
range of 4.5V to 17V.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1622699844-19203-2-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We alread have is_el1_instruction_abort(), add is_el1_data_abort()
helper and use it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210603120239.169018-1-wangkefeng.wang@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Provided the device driver does not implement dispatch budget accounting
(which only SCSI does) the loop in __blk_mq_do_dispatch_sched() pulls
requests from the IO scheduler as long as it is willing to give out any.
That defeats scheduling heuristics inside the scheduler by creating
false impression that the device can take more IO when it in fact
cannot.
For example with BFQ IO scheduler on top of virtio-blk device setting
blkio cgroup weight has barely any impact on observed throughput of
async IO because __blk_mq_do_dispatch_sched() always sucks out all the
IO queued in BFQ. BFQ first submits IO from higher weight cgroups but
when that is all dispatched, it will give out IO of lower weight cgroups
as well. And then we have to wait for all this IO to be dispatched to
the disk (which means lot of it actually has to complete) before the
IO scheduler is queried again for dispatching more requests. This
completely destroys any service differentiation.
So grab request tag for a request pulled out of the IO scheduler already
in __blk_mq_do_dispatch_sched() and do not pull any more requests if we
cannot get it because we are unlikely to be able to dispatch it. That
way only single request is going to wait in the dispatch list for some
tag to free.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210603104721.6309-1-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are BIOSes that are known to corrupt the memory under 1M, or more
precisely under 640K because the memory above 640K is anyway reserved
for the EGA/VGA frame buffer and BIOS.
To prevent usage of the memory that will be potentially clobbered by the
kernel, the beginning of the memory is always reserved. The exact size
of the reserved area is determined by CONFIG_X86_RESERVE_LOW build time
and the "reservelow=" command line option. The reserved range may be
from 4K to 640K with the default of 64K. There are also configurations
that reserve the entire 1M range, like machines with SandyBridge graphic
devices or systems that enable crash kernel.
In addition to the potentially clobbered memory, EBDA of unknown size may
be as low as 128K and the memory above that EBDA start is also reserved
early.
It would have been possible to reserve the entire range under 1M unless for
the real mode trampoline that must reside in that area.
To accommodate placement of the real mode trampoline and keep the memory
safe from being clobbered by BIOS, reserve the first 64K of RAM before
memory allocations are possible and then, after the real mode trampoline
is allocated, reserve the entire range from 0 to 1M.
Update trim_snb_memory() and reserve_real_mode() to avoid redundant
reservations of the same memory range.
Also make sure the memory under 1M is not getting freed by
efi_free_boot_services().
[ bp: Massage commit message and comments. ]
Fixes: a799c2bd29 ("x86/setup: Consolidate early memory reservations")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Hugh Dickins <hughd@google.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213177
Link: https://lkml.kernel.org/r/20210601075354.5149-2-rppt@kernel.org
Currently sbs-battery supports three string properties -
manufacturer, model_name, and chemistry. Buffers for those
properties are currently defined as global variables.
This patch moves those global variables into struct sbs_info
and cache/reuse them as they are all constant values.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
MT8195 are highly integrated SoC and use PMIC_MT6359 for
power management. This patch adds pwrap master driver to
access PMIC_MT6359.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Link: https://lore.kernel.org/r/20210602112050.12338-3-james.lo@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
With the new method of flushing/stopping the workqueue before doing bus
removal, the old mechanism of using refcount and wait for completion
is no longer needed. Remove those dead code.
Link: https://lore.kernel.org/r/1620806809-31055-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
[lorenzo.pieralisi@arm.com: Reworded subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Adds properties for setting the maximum current to USB, ADP and Battery
supplies. USB and ADP limits are reset to OTP values upon replugging.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The RC5T619 can detect SDP, CDP and DCP chargers, so let's add support
for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().
This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.
Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.
Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>