In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210324204836.29668-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We should indicate that we're not using the HPD pin on this device, per
the binding document. Otherwise if code in the future wants to enable
HPD in the bridge when this property is absent we'll be wasting power
powering hpd when we don't use it on trogdor boards. We didn't notice
this before because the kernel driver blindly disables hpd, but that
won't be true for much longer.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210324025534.1837405-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715, 5f8d3ab136, which is needed to allow angler to boot after
3edfb7bd76 ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac7 ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the compatible to make the driver probe and tell the
driver where to look for the "xo" clock to make sure everything
works.
Then we get a happy (eh, happier) 8996:
somainline-sdcard:/home/konrad# cat /sys/kernel/debug/clk/pwrcl_pll/clk_rate
1152000000
Don't backport without "arm64: dts: qcom: msm8996: Add CPU opps", as
the system fails to boot without consumers for these clocks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527192958.775434-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the operating points capabilities of the kryo CPUs, that can be
used for frequency scaling. There are two differents operating point
tables, one for the big cluster and one for the LITTLE cluster.
This frequency scaling support can then be used as a passive cooling
device (cpufreq cooling device).
Only add nominal fmax for now, since there is no dynamic control of
VDD APC (s11..) which is statically set at its nominal value.
Original patch link: https://patchwork.kernel.org/project/linux-arm-msm/patch/1595253740-29466-6-git-send-email-loic.poulain@linaro.org/
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[konrad: drop the thermals part, rebase and remove spaces within <>]
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-2-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
CoachZ rev3 uses a 100k NTC thermistor for the charger temperatures,
instead of the 47k NTC that is stuffed in earlier revisions. Add .dts
files for rev3.
The 47k NTC currently isn't supported by the PM6150 ADC driver.
Disable the charger thermal zone for rev1 and rev2 to avoid the use
of bogus temperature values.
This also gets rid of the explicit DT files for rev2 and handles
rev2 in the rev1 .dts instead. There was some back and forth
downstream involving the 'dmic_clk_en' pin, after that was sorted
out the DT for rev1 and rev2 is the same.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.3.I95b8a63103b77cab6a7cf9c150f0541db57fda98@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only kernel visible change with respect to rev2 is that pompom
rev3 changed the charger thermistor from a 47k to a 100k NTC to use
a thermistor which is supported by the PM6150 ADC driver.
Disable the charger thermal zone for pompom rev1 and rev2 to avoid
the use of bogus temperature values from the unsupported thermistor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.2.I4138c3edee23d1efa637eef51e841d9d2e266659@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit f73558cc83d1 ("arm64: dts: qcom: sc7180: Disable charger
thermal zone for lazor") disables the charger thermal zone for
specific lazor revisions due to an unsupported thermistor type.
The initial idea was to disable the thermal zone for older
revisions and leave it enabled for newer ones that use a
supported thermistor. Finally the thermistor won't be changed
on newer revisions, hence the thermal zone should be disabled
for all lazor (and limozeen) revisions. Instead of disabling
it per revision do it once in the shared .dtsi for lazor.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210322094628.v4.1.I6d587e7ae72a5a47253bb95dfdc3158f8cc8a157@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We had introduced the QUP-CORE ICC path to put proxy votes from
QUP wrapper on behalf of earlycon, if other users of QUP-CORE turn
off this clock before the real console is probed, unclocked access
to HW was seen from earlycon.
With ICC sync state support proxy votes are no longer need as ICC
will ensure that the default bootloader votes are not removed until
all it's consumer are probed.
We can safely remove ICC path for QUP-CORE clock from QUP wrapper
device.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210324101836.25272-3-rojay@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some node unit addresses were put wrongly in the dts, resulting in
below warning when run with W=1
arch/arm64/boot/dts/qcom/sm8350.dtsi:693.34-702.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c222000: simple-bus unit address format error, expected "c263000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:704.34-713.5: Warning (simple_bus_reg): /soc@0/thermal-sensor@c223000: simple-bus unit address format error, expected "c265000"
arch/arm64/boot/dts/qcom/sm8350.dtsi:1180.32-1185.5: Warning (simple_bus_reg): /soc@0/interconnect@90e0000: simple-bus unit address format error, expected "90c0000"
Fix by correcting to the correct address as given in reg node
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210513060733.382420-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With this patch, DMA has a chance of probing and doing something
useful.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@microsoft.com>
Link: https://lore.kernel.org/r/20210417061951.2105530-3-balbi@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The speedbin value blown in the efuse is used to determine is used to
determine the voltage and frequency value for different IPs, including
GPU, CPUs... So it's really not a gpu specific information.
This patch simply renames 'gpu_speed_bin' node to 'speedbin'.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210527194455.782108-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the QUSB USB PHY-s has been left enabled by
default, this is probably just a mistake as other
USB PHY-s are disabled by default.
It makes no sense to have it enabled by default as
not all board implement USB ports, so disable it.
Reviewed-by: Kathiravan T <kathirav@codeaurora.org>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20210526150125.1816335-1-robimarko@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The kernel versions including the following commits are referenced:
DRM_CLIENT_CAP_STEREO_3D
61d8e32825 ("drm: Add a STEREO_3D capability to the SET_CLIENT_CAP ioctl")
DRM_CLIENT_CAP_UNIVERSAL_PLANES
681e7ec730 ("drm: Allow userspace to ask for universal plane list (v2)")
c7dbc6c9ae ("drm: Remove command line guard for universal planes")
DRM_CLIENT_CAP_ATOMIC
88a48e297b ("drm: add atomic properties")
8b72ce158c ("drm: Always enable atomic API")
DRM_CLIENT_CAP_ASPECT_RATIO
7595bda2fb ("drm: Add DRM client cap for aspect-ratio")
DRM_CLIENT_CAP_WRITEBACK_CONNECTORS
d67b6a2065 ("drm: writeback: Add client capability for exposing writeback connectors")
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/434202/
Make it clear that the client is responsible for enabling ATOMIC
prior to enabling WRITEBACK_CONNECTORS. Linkify the reference to
ATOMIC.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/434200/
In the docs for DRM_CLIENT_CAP_STEREO_3D and
DRM_CLIENT_CAP_ASPECT_RATIO, reference the DRM_MODE_FLAG_* defines
that get set when the cap is enabled.
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/434201/
-----BEGIN PGP SIGNATURE-----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=vV+Y
-----END PGP SIGNATURE-----
Merge tag 'gfs2-v5.13-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fixes from Andreas Gruenbacher:
"Various gfs2 fixes"
* tag 'gfs2-v5.13-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix use-after-free in gfs2_glock_shrink_scan
gfs2: Fix mmap locking for write faults
gfs2: Clean up revokes on normal withdraws
gfs2: fix a deadlock on withdraw-during-mount
gfs2: fix scheduling while atomic bug in glocks
gfs2: Fix I_NEW check in gfs2_dinode_in
gfs2: Prevent direct-I/O write fallback errors from getting lost
As the back camera is not implemented disable the second pair of fimc
child nodes as they are not functional. This prevents creating the
associated /dev/videoX devices.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Link: https://lore.kernel.org/r/20210530105535.4165-1-timon.baetz@protonmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmC0vhsACgkQnJ2qBz9k
QNlI9ggAjZSqIvNNs1w6VafSRY7XP5vItKAe0jhguD0o1ZtUI1gM1JlOJzbgt2z5
gpm/4v4485h5JUXNrB5TeQ1woOOvFKzlUcIr+ZgUiyq2UgZj6PzvK599u2TFf1vc
gLMAUx5YgWafr048orhcSBqaYic04LESQ17op+9UjgBB7ATbNjJmEBb/+WvGh9os
8c4V9JrCTMdNJ5Rpc5+JsWAksgZKrW9VjTw8mHisWB0NIIPQWGCML8Z4ACzNObCW
CrXL9xWgaQDov1okJSA0ZNkdatGhh4h/NxIZ2sLGg2F3bDfZwN+kFu6gqpxhTEVV
v83aTAP3UxbK8bwRj0+lm/LImxULjA==
=t4P5
-----END PGP SIGNATURE-----
Merge tag 'fsnotify_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify fixes from Jan Kara:
"A fix for permission checking with fanotify unpriviledged groups.
Also there's a small update in MAINTAINERS file for fanotify"
* tag 'fsnotify_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: fix permission model of unprivileged group
MAINTAINERS: Add Matthew Bobrowski as a reviewer
The Microchip LAN8710Ai PHY requires XTAL1/CLKIN external clock to be
enabled when the nRST is toggled according to datasheet Microchip
LAN8710A/LAN8710Ai DS00002164B page 35 section 3.8.5.1 Hardware Reset:
"
A Hardware reset is asserted by driving the nRST input pin low. When
driven, nRST should be held low for the minimum time detailed in
Section 5.5.3, "Power-On nRST & Configuration Strap Timing," on page
59 to ensure a proper transceiver reset. During a Hardware reset, an
external clock must be supplied to the XTAL1/CLKIN signal.
"
This is accidentally fulfilled in the current setup, where ETHCK_K is used
to supply both PHY XTAL1/CLKIN and is also fed back through eth_clk_fb to
supply ETHRX clock of the DWMAC. Hence, the DWMAC enables ETHRX clock,
that has ETHCK_K as parent, so ETHCK_K clock are also enabled, and then
the PHY reset toggles.
However, this is not always the case, e.g. in case the PHY XTAL1/CLKIN
clock are supplied by some other clock source than ETHCK_K or in case
ETHRX clock are not supplied by ETHCK_K. In the later case, ETHCK_K would
be kept disabled, while ETHRX clock would be enabled, so the PHY would
not be receiving XTAL1/CLKIN clock and the reset would fail.
Improve the DT by adding the PHY clock phandle into the PHY node, which
then also requires moving the PHY reset GPIO specifier in the same place
and that then also requires correct PHY reset GPIO timing, so add that
too.
A brief note regarding the timing, the datasheet says the reset should
stay asserted for at least 100uS and software should wait at least 200nS
after deassertion. Set both delays to 500uS which should be plenty.
Fixes: 34e0c7847d ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
With the introduction of per-cpu wakeup devices that can be used in
preference to the broadcast timer, print the name of such devices when
they are available.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-6-will@kernel.org
When configuring the broadcast timer on entry to and exit from deep idle
states, prefer a per-CPU wakeup timer if one exists.
On entry to idle, stop the tick device and transfer the next event into
the oneshot wakeup device, which will serve as the wakeup from idle. To
avoid the overhead of additional hardware accesses on exit from idle,
leave the timer armed and treat the inevitable interrupt as a (possibly
spurious) tick event.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-5-will@kernel.org
Some SoCs have two per-cpu timer implementations where the timer with the
higher rating stops in deep idle (i.e. suffers from CLOCK_EVT_FEAT_C3STOP)
but is otherwise preferable to the timer with the lower rating. In such a
design, selecting the higher rated devices relies on a global broadcast
timer and IPIs to wake up from deep idle states.
To avoid the reliance on a global broadcast timer and also to reduce the
overhead associated with the IPI wakeups, extend
tick_install_broadcast_device() to manage per-cpu wakeup timers separately
from the broadcast device.
For now, these timers remain unused.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-4-will@kernel.org
In preparation for adding support for per-cpu wakeup timers, split
_tick_broadcast_oneshot_control() into a helper function which deals
only with the broadcast timer management across idle transitions.
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-3-will@kernel.org
tick-broadcast.o is only built if CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
so remove the redundant #ifdef guards around the definition of
tick_receive_broadcast().
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210524221818.15850-2-will@kernel.org
Use the DEVICE_ATTR_[RO|WO] helpers instead of plain DEVICE_ATTR, which
makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210523065825.19684-1-yuehaibing@huawei.com
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531135622.3348252-1-yukuai3@huawei.com
The Tegra clock driver contains legacy code which deasserts hardware reset
when peripheral clocks are enabled. This behaviour comes from a pre-CCF
era of the Tegra drivers. This is unacceptable for modern kernel drivers
which use generic CCF and reset-control APIs because it breaks assumptions
of the drivers about clk/reset sequences and about reset-propagation
delays. Hence remove the awkward legacy behaviour from the clk driver.
In particular PMC driver assumes that hardware blocks remains in reset
while power domain is turning on, but the clk driver deasserts the reset
before power clamp is removed, hence breaking the driver's assumption.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The external clocks don't have reset bits as they don't belong to any
specific hardware unit. Mark them as not having reset control for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Check whether thermal DIV2 throttle is active in order to report
the CPU frequency properly. This very useful for userspace tools
like cpufreq-info which show actual frequency asserted from hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Zero clock rate doesn't make sense for PLLs and tegra-clk driver enters
into infinite loop on trying to calculate PLL parameters for zero rate.
Make code to error out if requested rate is zero.
Originally this trouble was found by Robert Yang while he was trying to
bring up upstream kernel on Samsung Galaxy Tab, which happened due to a
bug in Tegra DRM driver that erroneously sets PLL rate to zero. This
issues came over again recently during of kernel bring up on ASUS TF700T.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Higher SCLK rates on Tegra20 require high core voltage. The higher
clock rate may have a positive performance effect only for AHB DMA
transfers and AVP CPU, but both aren't used by upstream kernel at all.
Halve SCLK rate on Tegra20 in order to remove the high core voltage
requirement.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PLLU (USB) consists of the PLL configuration itself and configuration
of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114,
where T114 immediately bails out if PLLU is enabled and T30 re-enables
a potentially already enabled PLL (left after bootloader) and then fully
reprograms it, which could be unsafe to do. The correct way should be to
skip enabling of the PLL if it's already enabled and then apply
configuration to the outputs. This patch doesn't fix any known problems,
it's a minor improvement.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The refcounting of the gate clocks has a bug causing the enable_refcnt
to underflow when unused clocks are disabled. This happens because clk
provider erroneously bumps the refcount if clock is enabled at a boot
time, which it shouldn't be doing, and it does this only for the gate
clocks, while peripheral clocks are using the same gate ops and the
peripheral clocks are missing the initial bump. Hence the refcount of
the peripheral clocks is 0 when unused clocks are disabled and then the
counter is decremented further by the gate ops, causing the integer
underflow.
Fix this problem by removing the erroneous bump and by implementing the
disable_unused() callback, which disables the unused gates properly.
The visible effect of the bug is such that the unused clocks are never
gated if a loaded kernel module grabs the unused clocks and starts to use
them. In practice this shouldn't cause any real problems for the drivers
and boards supported by the kernel today.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 600MHz is a too high clock rate for some SoC versions for the video
decoder hardware and this may cause stability issues. Use 300MHz for the
video decoder by default, which is supported by all hardware versions.
Fixes: ed1a2459e2 ("clk: tegra: Add Tegra20/30 EMC clock implementation")
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hci_sock_dev_event() function will cleanup the hdev object for
sockets even if this object may still be in used within the
hci_sock_bound_ioctl() function, result in UAF vulnerability.
This patch replace the BH context lock to serialize these affairs
and prevent the race condition.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Parameterize code in several places to allow scaling of windows. Note
that this currently still relies on static programming of the various
metering and memory pool allocation registers. This seems to work for
the common cases, but may eventually need to be updated to support
use-cases with multiple windows and higher bandwidth and latency
requirements.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver currently exposes several YUV formats but fails to properly
program all the registers needed to display such formats. Add the right
programming sequences so that overlay windows can be used to accelerate
color format conversions in multimedia playback use-cases.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The format modifier is 64bit, while DRM_FORMAT_MOD_NVIDIA_SECTOR_LAYOUT
uses BIT() macro that is 32bit on ARM32.
The (modifier &= ~DRM_FORMAT_MOD_NVIDIA_SECTOR_LAYOUT) doesn't work as
expected on ARM32 and tegra_fb_get_tiling() fails for the tiled formats
on 32bit Tegra because modifier mask isn't applied properly. Use the
BIT_ULL() macro to fix this trouble.
Fixes: 7b6f846785 ("drm/tegra: Support sector layout on Tegra194")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These functions haven't been used, so just remove them. The patch
just uses grep to verify.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Simek <monstr@monstr.eu>
Link: https://lore.kernel.org/r/1622350408-44875-3-git-send-email-guoren@kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>