Remove devm_kfree of memory where VLAN entry to RVU PF mapping
info is saved. This will be freed anyway at driver exit.
Having this could result in warning from devm_kfree() if
the memory is not allocated due to errors in rvu_nix_block_init()
before nix_setup_txvlan().
Fixes: 9a946def26 ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing failed message if driver does not have enough queues to
complete TC command. Without this fix no message is displayed in dmesg.
Fixes: a9ce82f744 ("i40e: Enable 'channel' mode in mqprio for TC configs")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In SW DCB mode the packets sent receive incorrect UP tags. They are
constructed correctly and put into tx_ring, but UP is later remapped by
HW on the basis of TCTUPR register contents according to Tx queue
selected, and BW used is consistent with the new UP values. This is
caused by Tx queue selection in kernel not taking into account DCB
configuration. This patch fixes the issue by implementing the
ndo_select_queue NDO callback.
Fixes: fd0a05ce74 ("i40e: transmit, receive, and NAPI")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In case of PHY type error occurs, the message was too generic.
Add additional info to PHY type error indicating that it can be
wrong cable connected.
Fixes: 124ed15bf1 ("i40e: Add dual speed module support")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d0704 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Correct the message flow between driver and firmware when disabling
queues.
Previously in case of PF reset (due to required reinit after reconfig),
the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up
occasionally. The error was not a real issue of hardware or firmware,
it was caused by wrong sequence of messages invoked by the driver.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Because of the significant overhead that retpolines pose on indirect
calls, the tracepoint code was updated to use the new "static_calls" that
can modify the running code to directly call a function instead of using
an indirect caller, and this function can be changed at runtime.
In the tracepoint code that calls all the registered callbacks that are
attached to a tracepoint, the following is done:
it_func_ptr = rcu_dereference_raw((&__tracepoint_##name)->funcs);
if (it_func_ptr) {
__data = (it_func_ptr)->data;
static_call(tp_func_##name)(__data, args);
}
If there's just a single callback, the static_call is updated to just call
that callback directly. Once another handler is added, then the static
caller is updated to call the iterator, that simply loops over all the
funcs in the array and calls each of the callbacks like the old method
using indirect calling.
The issue was discovered with a race between updating the funcs array and
updating the static_call. The funcs array was updated first and then the
static_call was updated. This is not an issue as long as the first element
in the old array is the same as the first element in the new array. But
that assumption is incorrect, because callbacks also have a priority
field, and if there's a callback added that has a higher priority than the
callback on the old array, then it will become the first callback in the
new array. This means that it is possible to call the old callback with
the new callback data element, which can cause a kernel panic.
static_call = callback1()
funcs[] = {callback1,data1};
callback2 has higher priority than callback1
CPU 1 CPU 2
----- -----
new_funcs = {callback2,data2},
{callback1,data1}
rcu_assign_pointer(tp->funcs, new_funcs);
/*
* Now tp->funcs has the new array
* but the static_call still calls callback1
*/
it_func_ptr = tp->funcs [ new_funcs ]
data = it_func_ptr->data [ data2 ]
static_call(callback1, data);
/* Now callback1 is called with
* callback2's data */
[ KERNEL PANIC ]
update_static_call(iterator);
To prevent this from happening, always switch the static_call to the
iterator before assigning the tp->funcs to the new array. The iterator will
always properly match the callback with its data.
To trigger this bug:
In one terminal:
while :; do hackbench 50; done
In another terminal
echo 1 > /sys/kernel/tracing/events/sched/sched_waking/enable
while :; do
echo 1 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
echo 0 > /sys/kernel/tracing/set_event_pid;
sleep 0.5
done
And it doesn't take long to crash. This is because the set_event_pid adds
a callback to the sched_waking tracepoint with a high priority, which will
be called before the sched_waking trace event callback is called.
Note, the removal to a single callback updates the array first, before
changing the static_call to single callback, which is the proper order as
the first element in the array is the same as what the static_call is
being changed to.
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Reported-by: Stefan Metzmacher <metze@samba.org>
tested-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The variable ret is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Link: https://lkml.kernel.org/r/20210721120915.122278-1-colin.king@canonical.com
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
synchronize_rcu_tasks_rude() triggers IPIs and forces rescheduling on
all CPUs. It is a costly operation and, when targeting nohz_full CPUs,
very disrupting (hence the name). So avoid calling it when 'old_hash'
doesn't need to be freed.
Link: https://lkml.kernel.org/r/20210721114726.1545103-1-nsaenzju@redhat.com
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
alloc_synth_event() currently has the following code to initialize the
event fields and dynamic_fields:
for (i = 0, j = 0; i < n_fields; i++) {
event->fields[i] = fields[i];
if (fields[i]->is_dynamic) {
event->dynamic_fields[j] = fields[i];
event->dynamic_fields[j]->field_pos = i;
event->dynamic_fields[j++] = fields[i];
event->n_dynamic_fields++;
}
}
1) It would make more sense to have all fields keep track of their
field_pos.
2) event->dynmaic_fields[j] is assigned twice for no reason.
3) We can move updating event->n_dynamic_fields outside the loop, and just
assign it to j.
This combination makes the code much cleaner.
Link: https://lkml.kernel.org/r/20210721195341.29bb0f77@oasis.local.home
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The only user of this variable is in an #ifdef:
net/netfilter/nfnetlink_hook.c: In function 'nfnl_hook_entries_head':
net/netfilter/nfnetlink_hook.c:177:28: error: unused variable 'netdev' [-Werror=unused-variable]
Fixes: e2cf17d377 ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the histogram logic allows the user to write "cpu" in as an
event field, and it will record the CPU that the event happened on.
The problem with this is that there's a lot of events that have "cpu"
as a real field, and using "cpu" as the CPU it ran on, makes it
impossible to run histograms on the "cpu" field of events.
For example, if I want to have a histogram on the count of the
workqueue_queue_work event on its cpu field, running:
># echo 'hist:keys=cpu' > events/workqueue/workqueue_queue_work/trigger
Gives a misleading and wrong result.
Change the command to "common_cpu" as no event should have "common_*"
fields as that's a reserved name for fields used by all events. And
this makes sense here as common_cpu would be a field used by all events.
Now we can even do:
># echo 'hist:keys=common_cpu,cpu if cpu < 100' > events/workqueue/workqueue_queue_work/trigger
># cat events/workqueue/workqueue_queue_work/hist
# event histogram
#
# trigger info: hist:keys=common_cpu,cpu:vals=hitcount:sort=hitcount:size=2048 if cpu < 100 [active]
#
{ common_cpu: 0, cpu: 2 } hitcount: 1
{ common_cpu: 0, cpu: 4 } hitcount: 1
{ common_cpu: 7, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 7 } hitcount: 1
{ common_cpu: 0, cpu: 1 } hitcount: 1
{ common_cpu: 0, cpu: 6 } hitcount: 2
{ common_cpu: 0, cpu: 5 } hitcount: 2
{ common_cpu: 1, cpu: 1 } hitcount: 4
{ common_cpu: 6, cpu: 6 } hitcount: 4
{ common_cpu: 5, cpu: 5 } hitcount: 14
{ common_cpu: 4, cpu: 4 } hitcount: 26
{ common_cpu: 0, cpu: 0 } hitcount: 39
{ common_cpu: 2, cpu: 2 } hitcount: 184
Now for backward compatibility, I added a trick. If "cpu" is used, and
the field is not found, it will fall back to "common_cpu" and work as
it did before. This way, it will still work for old programs that use
"cpu" to get the actual CPU, but if the event has a "cpu" as a field, it
will get that event's "cpu" field, which is probably what it wants
anyway.
I updated the tracefs/README to include documentation about both the
common_timestamp and the common_cpu. This way, if that text is present in
the README, then an application can know that common_cpu is supported over
just plain "cpu".
Link: https://lkml.kernel.org/r/20210721110053.26b4f641@oasis.local.home
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: 8b7622bf94 ("tracing: Add cpu field for hist triggers")
Reviewed-by: Tom Zanussi <zanussi@kernel.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a7 ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
nft_nat reports a bogus EAFNOSUPPORT if no layer 3 information is specified.
Fixes: d07db9884a ("netfilter: nf_tables: introduce nft_validate_register_load()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In case the entry is evicted via garbage collection there is
delay between the timeout value and the eviction event.
This adjusts the stop value based on how much time has passed.
Fixes: b87a2f9199 ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The flowtable follows the same timeout approach as conntrack, use the
same idiom as in cc16921351 ("netfilter: conntrack: avoid same-timeout
update") but also include the fix provided by e37542ba11 ("netfilter:
conntrack: avoid possible false sharing").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We do a bforget and return for no journal case, so let's remove this
conflict comment.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Guoqing Jiang <jiangguoqing@kylinos.cn>
Link: https://lore.kernel.org/r/20210714055940.1553705-1-guoqing.jiang@linux.dev
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
if (!ext4_has_feature_mmp(sb)) then retval can be unitialized before
we jump to the wait_to_exit label.
Fixes: 61bb4a1c41 ("ext4: fix possible UAF when remounting r/o a mmp-protected file system")
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210713022728.2533770-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since drivers/mmc/host/sdhci-xenon.c declares the PROBE_PREFER_ASYNCHRONOUS
probe type, it is not guaranteed whether /dev/mmcblk0 will belong to
sdhci0 or sdhci1. In turn, this will break booting by:
root=/dev/mmcblk0p1
Fix the issue by adding aliases so that the old MMC controller indices
are preserved.
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Enabling the PINCTRL_SM8350 symbol without GPIOLIB or SCM causes a build
failure:
WARNING: unmet direct dependencies detected for PINCTRL_MSM
Depends on [m]: PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && (QCOM_SCM [=m] || !QCOM_SCM [=m])
Selected by [y]:
- PINCTRL_SM8350 [=y] && PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && OF [=y]
aarch64-linux-ld: drivers/pinctrl/qcom/pinctrl-msm.o: in function `msm_gpio_irq_set_type':
pinctrl-msm.c:(.text.msm_gpio_irq_set_type+0x1c8): undefined reference to `qcom_scm_io_readl'
The main problem here is the 'select PINCTRL_MSM', which needs to be a
'depends on' as it is for all the other front-ends. As the GPIOLIB
dependency is now implied by that, symbol, remove the duplicate
dependencies in the process.
Fixes: d5d348a327 ("pinctrl: qcom: Add SM8350 pinctrl driver")
Fixes: 376f9e34c1 ("drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIB")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210723091400.1669716-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In non-split data, we shouldn't be adding S1G and 6 GHz
data (or future bands) since we're really close to the
4k message size limit. Remove those bands, any modern
userspace that can use S1G or 6 GHz should already be
using split dumps, and if not then it needs to update.
Link: https://lore.kernel.org/r/20210712215329.31444162a2c2.I5555312e4a074c84f8b4e7ad79dc4d1fbfc5126c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The logic for starting aggregation sessions was recently moved from minstrel_ht
to mac80211, into the subif tx handler just after the sta lookup.
Unfortunately this didn't work for mesh interfaces, since the sta lookup is
deferred until a much later point in time on those.
Fix this by also calling the aggregation check right after the deferred sta
lookup.
Fixes: 08a46c6420 ("mac80211: move A-MPDU session check from minstrel_ht to mac80211")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210629112853.29785-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a monitor interface is present together with other interfaces, a
received skb is copied and received on the monitor netdev. Before, the
copied skb was allocated with exactly the amount of space needed for
the radiotap header, resulting in an skb without any headroom at all
being received on the monitor netdev. With the introduction of eBPF
and XDP in the kernel, skbs may be processed by custom eBPF programs.
However, since the skb cannot be reallocated in the eBPF program, no
more data or headers can be pushed. The old code made sure the final
headroom was zero regardless of the value of NET_SKB_PAD, so increasing
that constant would have no effect.
Now we allocate monitor skb copies with a headroom of NET_SKB_PAD bytes
before the radiotap header. Monitor interfaces now behave in the same
way as other netdev interfaces that honor the NET_SKB_PAD constant.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210628123713.2070753-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pinctrl_power_button/pinctrl_power_out each define single GPIO
pinmux, except it is exactly the other one than the matching gpio-keys
and gpio-poweroff DT nodes use for that functionality. Swap the two
GPIOs to correct this error.
Fixes: 50d29fdb76 ("ARM: dts: imx53: Add power GPIOs on M53Menlo")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The function imx_mmdc_perf_init recently had a 3rd argument added to
it but the equivalent macro was not updated and is still the older
2 argument version. Fix this by adding in the missing 3rd argumement
mmdc_ipg_clk.
Fixes: f07ec85365 ("ARM: imx: add missing clk_disable_unprepare()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The H_ENTER_NESTED hypercall is handled by the L0, and it is a request
by the L1 to switch the context of the vCPU over to that of its L2
guest, and return with an interrupt indication. The L1 is responsible
for switching some registers to guest context, and the L0 switches
others (including all the hypervisor privileged state).
If the L2 MSR has TM active, then the L1 is responsible for
recheckpointing the L2 TM state. Then the L1 exits to L0 via the
H_ENTER_NESTED hcall, and the L0 saves the TM state as part of the exit,
and then it recheckpoints the TM state as part of the nested entry and
finally HRFIDs into the L2 with TM active MSR. Not efficient, but about
the simplest approach for something that's horrendously complicated.
Problems arise if the L1 exits to the L0 with a TM state which does not
match the L2 TM state being requested. For example if the L1 is
transactional but the L2 MSR is non-transactional, or vice versa. The
L0's HRFID can take a TM Bad Thing interrupt and crash.
Fix this by disallowing H_ENTER_NESTED in TM[T] state entirely, and then
ensuring that if the L1 is suspended then the L2 must have TM active,
and if the L1 is not suspended then the L2 must not have TM active.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
Fixes: 8e591cb720 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The check that is done in setup_bootmem currently only works for 32-bit
kernel since the kernel mapping has been moved outside of the linear
mapping for 64-bit kernel. So make sure that for 64-bit kernel, the kernel
mapping does not overlap with the last 4K of the addressable memory.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Fixes: 2bfc6cd81b ("riscv: Move kernel mapping outside of linear mapping")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
For 64-bit kernel, the end of the address space is occupied by the
kernel mapping and currently, the functions to populate the kernel page
tables (i.e. create_p*d_mapping) do not override existing mapping so we
must make sure the linear mapping does not map memory in the kernel mapping
by clipping the memory above the memory limit.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Fixes: c9811e379b ("riscv: Add mem kernel parameter support")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
As described in Documentation/riscv/vm-layout.rst, the end of the
virtual address space for 64-bit kernel is occupied by the modules/BPF/
kernel mappings so this actually reduces the amount of memory we are able
to map and then use in the linear mapping. So make sure this limit is
correctly set.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Fixes: 2bfc6cd81b ("riscv: Move kernel mapping outside of linear mapping")
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The PHY configuration for the variant 2 is still missing the flag for
in-band signalling between PHY and MAC. Both sides - MAC and PHY - have
to match the setting. For now, Linux only supports setting the MAC side
and thus it has to match the setting the bootloader is configuring.
Enable in-band signalling to make ethernet work.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the conditional checking for out_data_len and skipping the fallocate
if it is 0. This is wrong will actually change any legitimate the fallocate
where the entire region is unallocated into a no-op.
Additionally, before allocating the range, if FALLOC_FL_KEEP_SIZE is set then
we need to clamp the length of the fallocate region as to not extend the size of the file.
Fixes: 966a3cb7c7 ("cifs: improve fallocate emulation")
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Hi Linus,
Please, pull the following patch that fixes a fall-through warning
when building with Clang and -Wimplicit-fallthrough on PowerPC.
Thanks
-----BEGIN PGP SIGNATURE-----
iQIyBAABCAAdFiEEkmRahXBSurMIg1YvRwW0y0cG2zEFAmD6BOoACgkQRwW0y0cG
2zGIrw/3f77v1zOX83P13dFkl9XfNGd5qrel+so0VzQCWGs+O+ZdgJsT4umD5IPW
FCTj2actCanVRBSKGK3jT5Ad6XA3U9FI3sG+PVyUCCJcTft/RX3gOsZGvu97TyIf
I2M4Cf0s0lahyuqHZu/xllgQRahoDYgo6nSCotSMkrwxSWYK3P5lRiBRm7v734nT
1V1P5ESrL5tw/qQoz4r1M72yfLJWpPvNQlKn4VMjIsRikNT01bGk63HKpfroptAd
+/x23S0bAShrJJjeafYcs4rt4nn56mnXsI6/EmK3Tlxwo9dwGc0W7jTs+zTKGi14
BxV4LVoX2xF11J6l56CWTarfLLEyVz4uhRFXSaq7AAaebDpyt6lHkY3QXgEoZley
7h1ULM9r7uaCSbHwIRVrytIGsoHkoG3I4okix+ERW9IFux+41fSS/qWz9EzbPVNs
jdSE8PPtFKVqEy793l0VpZkiqrfFN7tNglp090o+OD2kZktkGvMKXtfgOEhVMNxm
WaJ34qTRescaLHxrd0PpzbIkVTqubLufbBcAqCwm1ZM55SUwhTxSS4C4b1KEwlHK
3VzqFNaIeBg+FoF2MpGvEKvUCK8DDmLv64LYwK43fqLPfi3yAOPZnO766WrNJZNL
4IKOCT8ClCCKwSptzFATUW1FjWlapC2fb+B/C73MYjZJeJKuIg==
=nqZC
-----END PGP SIGNATURE-----
Merge tag 'fallthrough-fixes-clang-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fix from Gustavo Silva:
"Fix a fall-through warning when building with -Wimplicit-fallthrough
on PowerPC"
* tag 'fallthrough-fixes-clang-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
powerpc/pasemi: Fix fall-through warning for Clang
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmD5dZ4ACgkQ+mJfZA7r
E8oOjggAmpH/KcwfiQMoVx8ie28bO5bZzLTX05Cchi1DJ3Av3WuHFalekw+3AAJc
s58fU2eLp/FKZ796OPNZLtmVgA2984UioDI9TePUn5kQ0PixJh5p7hpuywDBafpH
C8jgp1dPbMDtTZGbLLt40tJYDNFKnaqQXiTYeDsqXhqlELcD9wfiqU6MwnBkmuoC
kAdYvHcXrnnavfT7faXW3VFhJWYPB5Ow9tFXG2taeGXlh08Jsb6pek/eukgHKmkP
10leCkrYVpCbju2LJnUMwX4cV9cxfF4hYPakB/TpuvH8QeMD2tFWuEjljCgxI5BR
l1spFg7NSiuMAsN5wocLFDvY3Y3hHw==
=jhBB
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2021-07-22' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Couple reverts from Jason getting rid of asynchronous command parsing
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YPl1sIyruD0U5Orl@intel.com
A previous commit shuffled some code around, and inadvertently used
struct file after fdput() had been called on it. As we can't touch
the file post fdput() dropping our reference, move the fdput() to
after that has been done.
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/io-uring/YPnqM0fY3nM5RdRI@zeniv-ca.linux.org.uk/
Fixes: f2a48dd09b ("io_uring: refactor io_sq_offload_create()")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Hi Linus,
Please, pull the following patch that fixes a couple of out-of-bounds
warnings in the media subsystem. This is part of the ongoing efforts
to globally enable -Warray-bounds.
Thanks!
-----BEGIN PGP SIGNATURE-----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=JRnb
-----END PGP SIGNATURE-----
Merge tag 'array-bounds-fixes-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull array bounds warning fix from Gustavo Silva:
"Fix a couple of out-of-bounds warnings in the media subsystem.
This is part of the ongoing efforts to globally enable -Warray-bounds"
* tag 'array-bounds-fixes-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf()
- tracing fix (Keith Busch)
- fix multipath head refcounting (Hannes Reinecke)
- Write Zeroes vs PI fix (me)
- drop a bogus WARN_ON (Zhihao Cheng)
-----BEGIN PGP SIGNATURE-----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=8oM5
-----END PGP SIGNATURE-----
Merge tag 'nvme-5.14-2021-07-22' of git://git.infradead.org/nvme into block-5.14
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.14:
- tracing fix (Keith Busch)
- fix multipath head refcounting (Hannes Reinecke)
- Write Zeroes vs PI fix (me)
- drop a bogus WARN_ON (Zhihao Cheng)"
* tag 'nvme-5.14-2021-07-22' of git://git.infradead.org/nvme:
nvme: set the PRACT bit when using Write Zeroes with T10 PI
nvme: fix nvme_setup_command metadata trace event
nvme: fix refcounting imbalance when all paths are down
nvme-pci: don't WARN_ON in nvme_reset_work if ctrl.state is not RESETTING
Coverity also complains about the way we calculate the offset
(starting from the address of a 4 byte array within the
header structure rather than from the beginning of the struct
plus 4 bytes) for SMB1 CIFSPOSIXDelFile. This changeset
doesn't change the address but makes it slightly clearer.
Addresses-Coverity: 711519 ("Out of bounds write")
Signed-off-by: Steve French <stfrench@microsoft.com>
Here are some new device ids and a device-id comment fix.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYPm10QAKCRALxc3C7H1l
CFOZAQC2oc/Lz74D6RUkPd5sgRgT8z1HamrbcTqcSrvXg91BTwD+M0VqfnGyXo+u
I/MDUnLC6edOtFS7JmCecKWcl0FVFgM=
=J+Kc
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.14-rc3
Here are some new device ids and a device-id comment fix.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
USB: serial: cp210x: fix comments for GE CS1000
USB: serial: option: add support for u-blox LARA-R6 family
Coverity also complains about the way we calculate the offset
(starting from the address of a 4 byte array within the
header structure rather than from the beginning of the struct
plus 4 bytes) for SMB1 CIFSPOSIXCreate. This changeset
doesn't change the address but makes it slightly clearer.
Addresses-Coverity: 711518 ("Out of bounds write")
Signed-off-by: Steve French <stfrench@microsoft.com>
