Add definitions for PROBE ICMP types and codes.
Add AFI definitions for IP and IPV6 as specified by IANA
Add a struct to represent the additional header when probing by IP
address (ctype == 3) for use in parsing incoming PROBE messages
Add a struct to represent the entire Interface Identification Object
(IIO) section of an incoming PROBE packet
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, action creation using ACT API in replace mode is buggy.
When invoking for non-existent action index 42,
tc action replace action bpf obj foo.o sec <xyz> index 42
kernel creates the action, fills up the netlink response, and then just
deletes the action after notifying userspace.
tc action show action bpf
doesn't list the action.
This happens due to the following sequence when ovr = 1 (replace mode)
is enabled:
tcf_idr_check_alloc is used to atomically check and either obtain
reference for existing action at index, or reserve the index slot using
a dummy entry (ERR_PTR(-EBUSY)).
This is necessary as pointers to these actions will be held after
dropping the idrinfo lock, so bumping the reference count is necessary
as we need to insert the actions, and notify userspace by dumping their
attributes. Finally, we drop the reference we took using the
tcf_action_put_many call in tcf_action_add. However, for the case where
a new action is created due to free index, its refcount remains one.
This when paired with the put_many call leads to the kernel setting up
the action, notifying userspace of its creation, and then tearing it
down. For existing actions, the refcount is still held so they remain
unaffected.
Fortunately due to rtnl_lock serialization requirement, such an action
with refcount == 1 will not be concurrently deleted by anything else, at
best CLS API can move its refcount up and down by binding to it after it
has been published from tcf_idr_insert_many. Since refcount is atleast
one until put_many call, CLS API cannot delete it. Also __tcf_action_put
release path already ensures deterministic outcome (either new action
will be created or existing action will be reused in case CLS API tries
to bind to action concurrently) due to idr lock serialization.
We fix this by making refcount of newly created actions as 2 in ACT API
replace mode. A relaxed store will suffice as visibility is ensured only
after the tcf_idr_insert_many call.
Note that in case of creation or overwriting using CLS API only (i.e.
bind = 1), overwriting existing action object is not allowed, and any
such request is silently ignored (without error).
The refcount bump that occurs in tcf_idr_check_alloc call there for
existing action will pair with tcf_exts_destroy call made from the
owner module for the same action. In case of action creation, there
is no existing action, so no tcf_exts_destroy callback happens.
This means no code changes for CLS API.
Fixes: cae422f379 ("net: sched: use reference counting action init")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lan87xx_config_aneg_ext was introduced to configure
LAN95xxA but as well writes to undocumented register of LAN87xx.
This fix prevents that access.
The function lan87xx_config_aneg_ext gets more suitable for the new
behavior name.
Reported-by: Måns Rullgård <mans@mansr.com>
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original rxe implementation it was intended to use a common object
to represent MRs and MWs but they are different enough to separate these
into two objects.
This allows replacing the mem name with mr for MRs which is more
consistent with the style for the other objects and less likely to be
confusing. This is a long patch that mostly changes mem to mr where it
makes sense and adds a new rxe_mw struct.
Link: https://lore.kernel.org/r/20210325212425.2792-1-rpearson@hpe.com
Signed-off-by: Bob Pearson <rpearson@hpe.com>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmBjB18THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqRyEB/9zoqqwOk9dpgRjNr0hxeJUWcP1Lu56
rCZP+xN+hs4Vcc2IM5vhXSeLZA2UwE12Mq49M2AhBbCH6VHPvm7OwV5NS+cbWsmQ
Q9xsObLBz9/VZZHMKpBSIHftjrmEY6DBLFtvPlqj7jqPKqcUuP92Gc494nlok+uR
rDqsIWmXJoAJTp/w7gYRxTidV9MplXuuL0yrBSax7UlwblDmqkt/ccEuMwXB8aD6
oyPhNZTRt7+TRsgEAlg+ml6XVA7/m8r1e06jU5csi57y/tWsrjuid3Vu8n1JK9f0
9ytE3g0aJgXGNza3LG1Rc0aWWFAMgI3QkcXzP0vgvZucjBk0lKwtBUXq
=+WEA
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.13-20210330' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2021-03-30
this is a pull request of 39 patches for net-next/master.
The first two patches update the MAINTAINERS file. One is by me and
removes Dan Murphy from the from m_can and tcan4x5x. The other one is
by Pankaj Sharma and updates the maintainership of the m-can mmio
driver.
The next three patches are by me and update the CAN echo skb handling.
Vincent Mailhol provides 5 patches where Transmitter Delay
Compensation is added CAN bittiming calculation is cleaned up.
The next patch is by me and adds a missing HAS_IOMEM to the grcan
driver.
Michal Simek's patch for the xilinx driver add dev_err_probe()
support.
Arnd Bergmann's patch for the ucan driver fixes a compiler warning.
Stephane Grosjean provides 3 patches for the peak USB drivers, which
add ethtool set_phys_id and CAN one-shot mode.
Xulin Sun's patch removes a not needed return check in the m-can
driver. Torin Cooper-Bennun provides 3 patches for the m-can driver
that add rx-offload support to ensure that skbs are sent from softirq
context. Wan Jiabing's patch for the tcan4x5x driver removes a
duplicate include.
The next 6 patches are by me and target the mcp251xfd driver. They add
devcoredump support, simplify the UINC handling, and add HW timestamp
support.
The remaining 12 patches target the c_can driver. The first 6 are by
me and do generic checkpatch related cleanup work. Dario Binacchi's
patches bring some cleanups and increase the number of usable message
objects from 16 to 64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy function doesn't limit the source length, use the preferred
strscpy function instead.
Link: https://lore.kernel.org/r/20210329120131.18793-1-galpress@amazon.com
Reviewed-by: Firas JahJah <firasj@amazon.com>
Reviewed-by: Yossi Leybovich <sleybo@amazon.com>
Signed-off-by: Gal Pressman <galpress@amazon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Coexistence of CQE compression and HW PTP time-stamp:
From Aya this series improves mlx5 netdev driver to allow
both mlx5 CQE compression (RX descriptor compression, that saves on PCI
transaction) and HW time-stamp PTP to co-exists.
Prior to this series both features were mutually exclusive due to the
nature of CQE compression which reduces the size of RX descriptor for
the price of trimming some data, such as the time-stamp.
In order to allow CQE compression when PTP time stamping is enabled,
We enable it on the regular performance critical RX queues which will
service all the data path traffic that is not PTP.
PTP traffic will be re-directed to dedicated RX queues on which we will
not enable CQE compression and thus keep the time-stamp intact.
Having both features is critical for systems with low PCI BW, e.g.
Multi-Host.
The series will be adding:
1) Infrastructure to create a dedicated RX queue to service the PTP traffic
2) Flow steering plumbing to capture PTP traffic both UDP packets with
destination port 319 and L2 packets with ethertype 0x88F7
3) Steer PTP traffic to the dedicated RX queue.
4) The feature will be enabled when PTP is being configured via the
already existing PTP IOCTL when CQE compression is active, otherwise
no change to the driver flow.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmBip2IACgkQSD+KveBX
+j5gvwf/W+nBOdtUjKfssaBD8we0aXGb9JSfZOfgo/buGbRK1myFDbQeTP5lA3E8
Ld42+ZdvyT4k6viXEDK2+Pq65/6/HXpfKrp354Z1jf3JalvPKia4T990dSa3pF7r
LrbmmRsdF0Ohx9cfNWagoiT9UTaY0qInKnhaEz9/VLvx3EQxp41B8HOW00jtg3Y0
YwBpnHiFxQg4EBvXXB7Ka0EYKUAlH0z5e8eCx/GlX4NUIf/QdSF3iG9azI2kzXy8
gvjPvltww/wJ87/Rr6Nm0lmnGI9ajg6b6hEWEIqa7gT8FHBQRb8BKyt5WjFxLxsk
mTfqrUn2CaHbfDkflAA2Q6qMxg/CGg==
=5kFJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-03-29
Coexistence of CQE compression and HW PTP time-stamp:
From Aya this series improves mlx5 netdev driver to allow
both mlx5 CQE compression (RX descriptor compression, that saves on PCI
transaction) and HW time-stamp PTP to co-exists.
Prior to this series both features were mutually exclusive due to the
nature of CQE compression which reduces the size of RX descriptor for
the price of trimming some data, such as the time-stamp.
In order to allow CQE compression when PTP time stamping is enabled,
We enable it on the regular performance critical RX queues which will
service all the data path traffic that is not PTP.
PTP traffic will be re-directed to dedicated RX queues on which we will
not enable CQE compression and thus keep the time-stamp intact.
Having both features is critical for systems with low PCI BW, e.g.
Multi-Host.
The series will be adding:
1) Infrastructure to create a dedicated RX queue to service the PTP traffic
2) Flow steering plumbing to capture PTP traffic both UDP packets with
destination port 319 and L2 packets with ethertype 0x88F7
3) Steer PTP traffic to the dedicated RX queue.
4) The feature will be enabled when PTP is being configured via the
already existing PTP IOCTL when CQE compression is active, otherwise
no change to the driver flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71da201f38 ("ACPI: scan: Defer enumeration of devices with
_DEP lists") dropped the following 2 lines from acpi_init_device_object():
/* Assume there are unmet deps until acpi_device_dep_initialize() runs */
device->dep_unmet = 1;
Leaving the initial value of dep_unmet at the 0 from the kzalloc(). This
causes the acpi_bus_get_status() call in acpi_add_single_object() to
actually call _STA, even though there maybe unmet deps, leading to errors
like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
Fix this by re-adding the dep_unmet = 1 initialization to
acpi_init_device_object() and modifying acpi_bus_check_add() to make sure
that dep_unmet always gets setup there, overriding the initial 1 value.
This re-fixes the issue initially fixed by
commit 63347db0af ("ACPI / scan: Use acpi_bus_get_status() to initialize
ACPI_TYPE_DEVICE devs"), which introduced the removed
"device->dep_unmet = 1;" statement.
This issue was noticed; and the fix tested on a Dell Venue 10 Pro 5055.
Fixes: 71da201f38 ("ACPI: scan: Defer enumeration of devices with _DEP lists")
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: 5.11+ <stable@vger.kernel.org> # 5.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
checkpatch started to complain about the mispelling of:
CHECK: 'wont' may be misspelled - perhaps 'won't'?
#459: FILE: ./net/batman-adv/bat_iv_ogm.c:459:
+ * - the resulting packet wont be bigger than
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Add hbr3_hbr2 voltage and premphasis swing table to support
HBR3 link rate.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1615914761-12300-1-git-send-email-khsieh@codeaurora.org
Fixes: 52e013d0bf ("phy: qcom-qmp: Add support for DP in USB3+DP combo phy")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the return value check typo which testing the wrong variable
in ingenic_usb_phy_probe().
Fixes: 31de313dfd ("PHY: Ingenic: Add USB PHY driver using generic PHY framework.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210305034933.3240914-1-weiyongjun1@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec ("phy: add support for USB cluster on the Armada 375 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In one of the error paths of the for_each_child_of_node() loop in
of_property_read_u32, add missing call to of_node_put().
Fix the following coccicheck warning:
./drivers/phy/ti/phy-j721e-wiz.c:786:1-23: WARNING: Function
"for_each_child_of_node" should have of_node_put() before return around
line 795.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/1614244674-66556-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When this was rewriten to get mainlined and start to
use 'linux/bitfield.h' headers, XTAL_MASK was wrong.
It must mask three bits but only two were used. Hence
properly fix it to make things work.
Fixes: d87da32372 ("phy: ralink: Add PHY driver for MT7621 PCIe PHY")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210302105412.16221-1-sergio.paracuellos@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update PCIe + USB register sequences for correct PLL1 clock configuration.
Also, update sequences for other USB configurations with dependent changes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/1614838096-32291-5-git-send-email-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For PCIe + QSGMII configuration where QSGMII was using PLL1 and was
expecting 10GHz clock, configuration was giving 8GHz clock. Update
register sequences to get correct PLL1 configuration.
Also, update single link PCIe and single link SGMII/QSGMII configurations
with related changes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/1614838096-32291-2-git-send-email-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external
reference clock. cmn_refclk_<p/m> can also be configured to output the
reference clock. Model this derived reference clock as a "clock" so that
platforms like AM642 EVM can enable it.
This is used by PCIe to use the same refclk both in local SERDES
and remote device. Add support here to drive refclk out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Link: https://lore.kernel.org/r/20210310120840.16447-7-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external
reference clock. cmn_refclk_<p/m> can also be configured to output the
reference clock. In order to drive the refclk out from the SERDES
(Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of WIZ.
Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM can
enable it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-6-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled the internal clocks depending on the
subnodes that are populated in device tree. However recent discussions
in the mailing list [1] suggested to just add #clock cells in the parent
DT node and model the clocks within the driver.
Model the mux clocks without device tree input for AM64x SoC. Don't
remove the earlier design since DT nodes for J7200 and J721e are already
upstreamed.
[1] -> http://lore.kernel.org/r/20210108025943.GA1790601@robh.at.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-5-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The frequency of the txmclk between PCIe and SERDES has
changed to 250MHz from 500MHz. Configure full rate divider
for AM64 accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-4-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Both "struct wiz_clk_div_sel" and "struct wiz_clk_mux_sel" are static
data that is common for all wiz instances. Including
"struct regmap_field" for each of the wiz instances can yield undesirable
results. Move "struct regmap_field" out of "struct wiz_clk_div_sel" and
"struct wiz_clk_mux_sel" and make them point to constant data.
So far no issues are observed since both these structures are not
accessed outside the probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-2-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new file name is marvell,armada-3700-utmi-phy.yaml
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210307163343.25684-3-kostap@marvell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for Marvell CP110 UTMI PHY driver allowing the USB2
port configuration independently from the boot loader setup.
The CP110/CP115 dies have 2 UTMI PHYs that could be connected
to two USB host controllers or to single USB device controller.
Since there is only one USB device controller on die, only one
of the UTMI PHYs could work in USB device mode.
The CONFIG_PHY_MVEBU_CP110_UTMI should be enabled for usage of
this driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210307163343.25684-2-kostap@marvell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- fix incorrect initialization and update of vdso data pages, which
results in incorrect tod clock steering, and that
clock_gettime(CLOCK_MONOTONIC_RAW, ...) returns incorrect values.
- update MAINTAINERS for s390 vfio drivers
-----BEGIN PGP SIGNATURE-----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=5z4s
-----END PGP SIGNATURE-----
Merge tag 's390-5.12-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- fix incorrect initialization and update of vdso data pages, which
results in incorrect tod clock steering, and that
clock_gettime(CLOCK_MONOTONIC_RAW, ...) returns incorrect values.
- update MAINTAINERS for s390 vfio drivers
* tag 's390-5.12-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
MAINTAINERS: add backups for s390 vfio drivers
s390/vdso: fix initializing and updating of vdso_data
s390/vdso: fix tod_steering_delta type
s390/vdso: copy tod_steering_delta value to vdso_data page
Make syncpoint expiration checks always use the same logic used by
the hardware. This ensures that there are no race conditions that
could occur because of the hardware triggering a syncpoint interrupt
and then the driver disagreeing.
One situation where this could occur is if a job incremented a
syncpoint too many times -- then the hardware would trigger an
interrupt, but the driver would assume that a syncpoint value
greater than the syncpoint's max value is in the future, and not
clean up the job.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before this patch, cancelled waiters would only be cleaned up
once their threshold value was reached. Make host1x_intr_put_ref
process the cancellation immediately to fix this.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Show the number of pending waiters in the debugfs status file.
This is useful for testing to verify that waiters do not leak
or accumulate incorrectly.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Syncpoints don't need to be associated with any client,
so remove the property, and expose host1x_syncpt_alloc.
This will allow allocating syncpoints without prior knowledge
of the engine that it will be used with.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR resets are exclusively shared with the SOR power domain. This
means that exclusive access can only be granted temporarily and in order
for that to work, a rigorous sequence must be observed. To ensure that a
single consumer gets exclusive access to a reset, each consumer must
implement a rigorous protocol using the reset_control_acquire() and
reset_control_release() functions.
However, these functions alone don't provide any guarantees at the
system level. Drivers need to ensure that the only a single consumer has
access to the reset at the same time. In order for the SOR to be able to
exclusively access its reset, it must therefore ensure that the SOR
power domain is not powered off by holding on to a runtime PM reference
to that power domain across the reset assert/deassert operation.
This used to work fine by accident, but was revealed when recently more
devices started to rely on the SOR power domain.
Fixes: 11c632e1cf ("drm/tegra: sor: Implement acquire/release for reset")
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 4bba4c4bb0 added tools/include/linux/compiler_types.h which
includes linux/compiler-gcc.h. Unfortunately, we had our own (empty)
compiler_types.h which overrode the one added by that commit, and
so we lost the definition of __must_be_array(). Removing our empty
compiler_types.h fixes the problem and reduces our divergence from the
rest of the tools.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Splitting an order-4 entry into order-2 entries would leave the array
containing pointers to 000040008000c000 instead of 000044448888cccc.
This is a one-character fix, but enhance the test suite to check this
case.
Reported-by: Zi Yan <ziy@nvidia.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
I wrote the documentation backwards; the new order of the entry is stored
in the xas and the caller passes the old entry.
Reported-by: Zi Yan <ziy@nvidia.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Coupling of display controllers used to rely on runtime PM to take the
companion controller out of reset. Commit fd67e9c6ed ("drm/tegra: Do
not implement runtime PM") accidentally broke this when runtime PM was
removed.
Restore this functionality by reusing the hierarchical host1x client
suspend/resume infrastructure that's similar to runtime PM and which
perfectly fits this use-case.
Fixes: fd67e9c6ed ("drm/tegra: Do not implement runtime PM")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Reported-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To avoid false lockdep warnings, give each client lock a different
lock class, passed from the initialization site by macro.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
RGB output doesn't allow to change parent clock rate of the display and
PCLK rate is set to 0Hz in this case. The tegra_dc_commit_state() shall
not set the display clock to 0Hz since this change propagates to the
parent clock. The DISP clock is defined as a NODIV clock by the tegra-clk
driver and all NODIV clocks use the CLK_SET_RATE_PARENT flag.
This bug stayed unnoticed because by default PLLP is used as the parent
clock for the display controller and PLLP silently skips the erroneous 0Hz
rate changes because it always has active child clocks that don't permit
rate changes. The PLLP isn't acceptable for some devices that we want to
upstream (like Samsung Galaxy Tab and ASUS TF700T) due to a display panel
clock rate requirements that can't be fulfilled by using PLLP and then the
bug pops up in this case since parent clock is set to 0Hz, killing the
display output.
Don't touch DC clock if pclk=0 in order to fix the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Qualcomm SoundWire controller supports Auto Enumeration of the
devices within the IP. This patch enables support for this feature.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-9-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Exporting these three functions makes sense as it can be used by
other controllers like Qualcomm during auto-enumeration!
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210330144719.13284-8-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to new interrupts which includes reporting some of the
error interrupts and adding support to SLAVE pending interrupt!
This patch also changes the interrupt handler behaviour on handling
any pending interrupts by checking it before returning out of irq handler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-7-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the existing code every soundwire register read and register write
are kinda blocked. Each of these are using a special command id that
generates interrupt after it successfully finishes. This is really
overhead, limiting and not really necessary unless we are doing
something special.
We can simply read/write the fifo that should also give exactly
what we need! This will also allow to read/write registers in
interrupt context, which was not possible with the special
command approach.
With previous approach number of interrupts generated
after enumeration are around 130:
$ cat /proc/interrupts | grep soundwire
21: 130 0 0 0 0 0 0 0 GICv3 234 Edge soundwire
after this patch they are just 3 interrupts
$ cat /proc/interrupts | grep soundwire
21: 3 0 0 0 0 0 0 0 GICv3 234 Edge soundwire
This has significantly not only reduced interrupting CPU during enumeration
but also during streaming!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-6-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Start the clock during initialization, doing this explicitly
will add more clarity when we are adding clock stop feature.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-5-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
version 1.5.1 and higher IPs of this controller required to set
continue execution on ignored command flag. This patch sets this flag.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210330144719.13284-4-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>