Check during cs35l56_system_resume() whether the firmware patch must
be applied again.
The FIRMWARE_MISSING flag in the PROTECTION_STATUS register indicates
whether the firmware has been patched.
In non-secure mode the FIRMWARE_MISSING flag is cleared at the end of
dsp_work(). If it is set after system-resume we know that dsp_work()
must be run again.
In secure mode the pre-OS loader will have done the secure patching
and cleared the FIRMWARE_MISSING flag. So this flag does not tell us
whether firmware memory was lost. But the driver could only be
downloading non-secure tunings, which is always safe to do.
If the driver has control of RESET we will have asserted it during
suspend so the firmware patch will have been lost. The driver would only
have control of RESET in non-secure mode.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168122674550.26.8545058503709956172@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For SoundWire usages, we need to use the global eml_lock to
serialize/protect all accesses to shared registers. Due to the split
implementation across two subsystems, we need to pass a pointer
around.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-19-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For DMIC and SSP, the DSP will be responsible for programming the
blobs and link registers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-18-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Small helpers to make DAI ops simpler.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-17-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Each SoundWire peripheral can be programmed from the manager side
either with a regular command FIFO, or with the HDaudio CORB/RIRB
DMA-based mechanism. The mapping between SoundWire peripheral and SDI
address is handled with the LSDIID register.
This mapping only works of course if each peripheral has a unique
address across all links. This has already been enforced in previous
Intel contributions allowing for an IDA-based solution for the device
number allocation.
The checks on the dev_num are handled at the SoundWire level, but the
locking is handled at the hda-mlink level.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper is an optimization where sync_go is only called when the
cmdsync field is actually set to a non-zero value.
Since this is also only used by SoundWire for now, only expose the
_unlocked version.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-15-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The multi-link synchronization uses the same concept and registers,
but moved to the HDAudio extended links.
Add helpers for sync_arm and sync_go which are the basic for the bus
reset, bank switch and clock stop.
Since SoundWire is the only user of those helpers, only expose the
_unlocked versions for now.
Note that SYNCGO is a write-only bit, so no error can be reported. We
still return 0 for compatibility with the SoundWire stream management
headers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-14-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These helpers configure the ratio between the base clock and the
hardware signal used for link synchronization.
The SYNCPRD is written before the first sublink is powered-up. The
SYNCPU bit is set, but it will only be cleared after the link is
powered-up, hence the implementation with a set/wait pattern.
These helpers are currently only needed by SoundWire support, where
the lock is taken at a higher level, so only the _unlocked versions
are exposed for now.
Note that the _wait_bit() implementation is similar to previous
helpers in drivers/soundwire, but with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with e.g. readl_poll_timeout().
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-13-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When INTC is set, LCTL exposes INTEN and INTSTS fields.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is needed for SoundWire integration.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The updated SoundWire Intel driver will need to rely on Extended
HDaudio links for power management, but it doesn't need to be aware of
all the HDaudio structures. Add convenience helpers to avoid polluting
SoundWire drivers too much with HDaudio information.
Since the SoundWire/Intel solution already takes the lock at a higher
level, the _unlocked PM helpers are used.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helpers to program SPA/CPA bits, using a mutex to access the
shared LCTL register if required.
All links are managed with the same LCTLx.SPA bits. However there are
quite a few implementation details to be aware of:
Legacy HDaudio multi-links are powered-up when exiting reset, which
requires the ref_count to be manually set to one when initializing the
link.
Alternate links for SoundWire/DMIC/SSP need to be explicitly
powered-up before accessing the SHIM/IP/Vendor-Specific SHIM space for
each sublink. DMIC/SSP/SoundWire are all different cases with a
different device/dai/hlink relationship.
SoundWire will handle power management with the auxiliary device
resume/suspend routine. The ref_count is not necessary in this case.
The DMIC/SSP will by contrast handle the power management from DAI
.startup and .shutdown callbacks.
The SSP has a 1:1 mapping between sublink and DAI, but it's
bidirectional so the ref_count will help avoid turning off the sublink
when one of the two directions is still in use.
The DMIC has a single link but two DAIs for data generated at
different sampling frequencies, again the ref_count will make sure the
two DAIs can be used concurrently.
And last the SoundWire Intel require power-up/down and bank switch to
be handled with a lock already taken, so the 'eml_lock' is made
optional with the _unlocked versions of the helpers.
Note that the _check_power_active() implementation is similar to
previous helpers in sound/hda/ext, with sleep duration and timeout
aligned with hardware recommendations. If desired, this helper could
be modified in a second step with .e.g. readl_poll_timeout()
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-9-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend hdac_ext_link to store information needed for ALT
links. Follow-up patches will include more functional patches for
power-up and down.
Note that this patch suggests the use of an 'eml_lock' to serialize
access to shared registers. SoundWire-specific sequence require the
lock to be taken at a higher level, as a result the helpers added in
follow-up patches will provide 'unlocked' versions when needed.
Also note that the low-level sequences with the 'hdaml_' prefix are
taken directly from the hardware specifications - naming conventions
included. The code will be split in two, with locking and linked-list
management handled separately to avoid mixing required hardware setup
and Linux-based resource management.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the functions will be used for SoundWire enumeration and power
management, to avoid cycles in module dependencies and simplify
integration all the HDaudio multi-link needs to move to a dedicated
module.
Drop no longer needed headers at the same time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new definitions for the HDaudio Extended link support,
specifically new registers for SoundWire, Intel DMIC and INTEL SSP
interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230404104127.5629-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_link has params/num_params, but it is unclear that
params for what. This patch clarify it is params for Codec2Codec.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7o5c2lk.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSPless mode of the ASoC/SOF driver can be used for hardware
verification and debug on platforms with HDaudio codecs. The DSP mode is
still needed on existing platforms for SSP, DMIC, SoundWire interfaces
managed by the GP-DMA.
This mode is also helpful to compare the legacy HDaudio driver with the
ASoC/SOF driver wrt. codec management and handling. In theory we use the
same code but differences are sometimes seen on jack detection and event
handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230404092115.27949-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC supports snd_soc_add_pcm_runtime(), but user need to
call it one-by-one if it has multi dai_links.
This patch adds snd_soc_add_pcm_runtimes() which supports multi
dai_links.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6u76nhq.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
On a platform when the DSP is in use, we cannot select individual links
to use or not use the DSP, it is either all or none. On some audio
endpoint, like HDMI/DP, it is preferred to not use any processing in DSP
to reduce the latency and to allow bytestream pass-through (DTS, DD,
etc)
IPC4 introduces a new type of end-to-end connection within the DSP which
is using the host DMA and link DMA in a single buffer, working
back-to-back, passing the received data without looking at it or trying
to understand the format, content.
This mode reduces the latency and allows non PCM streams to be sent from
userspace.
The feature is enabled per PCM bases, signalled in topology.
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
The CS35L56 is a high-performance boosted mono audio amplifier.
Supported control interfaces are I2C, SPI or SoundWire.
Supported audio interfaces are I2S/TDM or SoundWire.
The CS35L56 has a self-booting firmware in ROM, with the ability
to patch the firmware and/or apply tunings.
Patches #1 to #7 add support to cs_dsp and wm_adsp for self-booting
firmware and the ability to apply a .bin file without having to
apply a .wmfw.
Add logic for setting up and tearing down chained DMA connections.
Since pipelines are not used, all the logic to set the pipeline states
can be bypassed, with only the DMA programming sequences remaining. In
addition the same format needs to be used for host- and link-DMA,
without the usual fixup to use the S32_LE format on the link.
Note however that for convenience and compatibility with existing
definitions, the topology relies on the concept of pipelines with a
'USE_CHAIN_DMA' token indicating that all the logic shall be bypassed.
Unlike 'normal' ALSA sequences, the chain DMA is not programmed in
hw_params/hw_free. The IPC message to set-up and tear-down chained DMA
are sent in sof_ipc4_trigger_pipelines(), but the contents prepared
earlier.
Chained DMA is only supported by the Intel HDA DAI for now, and only
S16_LE and S32_LE formats are supported for now.
Signed-off-by: Jyri Sarha <jyri.sarha@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230321092654.7292-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the chained DMA mode, the firmware allocates buffers for the host
and link DMA, and takes care of copying data between host- and
link-DMA buffers in a low-latency thread. This is different to a
regular pipeline, no processing is allowed, and the connection between
host- and link DMA is handled with a dedicated IPC.
This patch exposes the macros needed to create the required IPC messages.
Signed-off-by: Jyri Sarha <jyri.sarha@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230321092654.7292-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Supported control interfaces are I2C, SPI or SoundWire.
Supported audio interfaces are I2S/TDM or SoundWire.
Most chip functionality is controlled by on-board ROM firmware that is
always running. The driver must apply patch/tune to the firmware
before using the CS35L56.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230320112245.115720-9-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are devices containing Halo Core DSPs that self-boot, cs_dsp is
used to manage the running firmware but the host does not have direct
control over starting and stopping the DSP and so cs_dsp should consider
the DSP to be always running.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230320112245.115720-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
substream->runtime will be attached when substream was opened
at snd_pcm_attach_substream(). When it uses DPCM,
FE substream->runtime is attached, but BE substream->runtime is not.
Thus, we are copying FE substream->runtime to BE.
But, we are copyig FE substream->runtime to FE dpcm->runtime first (A),
and copy it to BE dpcm->runtime (B), and copy it to
BE substream->runtime (C).
static int dpcm_fe_dai_open(...) {
...
(A) fe->dpcm[stream].runtime = fe_substream->runtime;
...
}
static int dpcm_be_connect(...) {
...
(B) be->dpcm[stream].runtime = fe->dpcm[stream].runtime;
...
}
int dpcm_be_dai_startup(...) {
...
(C) be_substream->runtime = be->dpcm[stream].runtime;
...
}
It is too roundabout and troublesome.
OTOH, it is directly copying fe_substream->runtime at dpcm_be_reparent()
without using be->dpcm[stream].runtime.
static void dpcm_be_reparent(...)
{
...
for_each_dpcm_fe(be, stream, dpcm) {
...
=> be_substream->runtime = fe_substream->runtime;
break;
}
}
This patch removes indirect copying.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8je64dh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The modules in IPC4 can have multiple 'pins' on their input and output
and these pins can receive or output audio in different formats.
Currently we assume that all pins are using the same format which is a
limitation that needs to be lifted in order to support more complex
components.
This series will extend and rework the format handling to allow
different formats on pins.
In preparation for handling processing modules with different
input/output pin counts, introduce two new tokens for input/output
audio format counts. Use these token values to parse all the available
audio formats from topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-11-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new struct sof_ipc4_pin_format which contains the pin index
and the buffer size. Replace the type of available input/output audio
formats in struct sof_ipc4_available_audio_format with this new struct
type and rename them to input_pin_fmts and output_pin_fmts.
Also, add a new token, SOF_TKN_CAVS_AUDIO_FORMAT_PIN_INDEX that will be
used to parse the pin index for the audio format from topology.
Currently we only set the audio format for Pin 0 in topology, so the
default value will be 0 for all audio formats.
Finally, parse the pin_index and the input/output buffer sizes
along with audio formats into the pin_format arrays in struct
sof_ipc4_available_audio_format. This makes the base_config array in struct
sof_ipc4_available_audio_format redundant. So remove it. This change
will allow the addition of audio formats for the non-zero pins in
topology transparent to the topology parser in the kernel.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-8-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not parse the SOF_TKN_CAVS_AUDIO_FORMAT_DMA_BUFFER_SIZE token as the
dma_buffer_size can be derived from the input/output buffer size and the
type of widget during copier prepare. For the deep buffer case,
introduce a new token that will be used to get the deep buffer DMA size
for the host copier from topology.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we use input/output and sink/source pins interchangeably.
Remove the references to sink/source pins and replace with input/output
pins everywhere for consistency and clarity.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename SOF_TKN_CAVS_AUDIO_FORMAT_IN_VALID and
SOF_TKN_CAVS_AUDIO_FORMAT_OUT_VALID as
SOF_TKN_CAVS_AUDIO_FORMAT_IN_VALID_BIT_DEPTH and
SOF_TKN_CAVS_AUDIO_FORMAT_OUT_VALID_BIT_DEPTH respectively.
These are currently not used.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230313124856.8140-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With IPC4 the sof_abit_hdr is only used between user space
(and in topology) and kernel.
The same abi header is used with small differencies like different
magic number and the type field have slightly different name, but
similar function in IPC4 (param_id).
Update the kernel documentation to highlight the differences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20230313110344.16644-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the comments for sof_abi_hdr to kernel style.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230313110344.16644-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
potential deadlock during directory renames that was introduced during
the merge window discovered by a combination of syzbot and lockdep.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAmQNVwIACgkQ8vlZVpUN
gaMwmgf/ZAasXZEMV0zaQZa8zP4KvMKZjWe6azkcJg4sb/HG9Q7JzeJDCurhhWUj
8+QnyUcuKTyWKYWjGf0f5CZaYEM5AZYij41UJzu2qMkz5hVXSqBVuY8KywxuiJv5
kfuIvQh0Onv0Yrg2qAc52/kZkq1lu2sl/F5ertBWjdpTUXdBUdrCxkUk+1BgQWAj
vNwi1/+gNuX7RxMboHqYmwXFP39vECd+wteNdsiK1hR8bLqL68duLLq8xQdHt4gS
sbVmJKR4j2Giw4ZnlYi9RiwKIO0beqocanp+cfOPulyj5mTM8X1lr0uvaLZgx2AF
lqrS3/5ksp45cRT70qCIz8je70hTSg==
=nN3T
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Bug fixes and regressions for ext4, the most serious of which is a
potential deadlock during directory renames that was introduced during
the merge window discovered by a combination of syzbot and lockdep"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: zero i_disksize when initializing the bootloader inode
ext4: make sure fs error flag setted before clear journal error
ext4: commit super block if fs record error when journal record without error
ext4, jbd2: add an optimized bmap for the journal inode
ext4: fix WARNING in ext4_update_inline_data
ext4: move where set the MAY_INLINE_DATA flag is set
ext4: Fix deadlock during directory rename
ext4: Fix comment about the 64BIT feature
docs: ext4: modify the group desc size to 64
ext4: fix another off-by-one fsmap error on 1k block filesystems
ext4: fix RENAME_WHITEOUT handling for inline directories
ext4: make kobj_type structures constant
ext4: fix cgroup writeback accounting with fs-layer encryption
The cpumask_check() was unnecessarily tight, and causes problems for the
users of cpumask_next().
We have a number of users that take the previous return value of one of
the bit scanning functions and subtract one to keep it in "range". But
since the scanning functions end up returning up to 'small_cpumask_bits'
instead of the tighter 'nr_cpumask_bits', the range really needs to be
using that widened form.
[ This "previous-1" behavior is also the reason we have all those
comments about /* -1 is a legal arg here. */ and separate checks for
that being ok. So we could have just made "small_cpumask_bits-1"
be a similar special "don't check this" value.
Tetsuo Handa even suggested a patch that only does that for
cpumask_next(), since that seems to be the only actual case that
triggers, but that all makes it even _more_ magical and special. So
just relax the check ]
One example of this kind of pattern being the 'c_start()' function in
arch/x86/kernel/cpu/proc.c, but also duplicated in various forms on
other architectures.
Reported-by: syzbot+96cae094d90877641f32@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=96cae094d90877641f32
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Link: https://lore.kernel.org/lkml/c1f4cc16-feea-b83c-82cf-1a1f007b7eb9@I-love.SAKURA.ne.jp/
Fixes: 596ff4a09b ("cpumask: re-introduce constant-sized cpumask optimizations")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* final coversions of drivers away from deprecated .probe
* make .probe_new the standard probe and convert I2C core to use it
-----BEGIN PGP SIGNATURE-----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=jm/G
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZAuS9AAKCRBZ7Krx/gZQ
6/HUAQCkaWkt0zi9dh+T5gKD9U9/R3DBLHm2W7o414ewFhEcaAEAjCrwc3c+RIf2
AEr8tsYNXI7Lqvh1q0QLugezChYyVgk=
=3K38
-----END PGP SIGNATURE-----
Merge tag 'pull-highmem' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull put_and_unmap_page() helper from Al Viro:
"kmap_local_page() conversions in local filesystems keep running into
kunmap_local_page()+put_page() combinations. We can keep inventing
names for identical inline helpers, but it's getting rather
inconvenient. I've added a trivial helper to linux/highmem.h instead.
I would've held that back until the merge window, if not for the mess
it causes in tree topology - I've several branches merging from that
one, and it's only going to get worse if e.g. ext2 stuff gets picked
by Jan"
* tag 'pull-highmem' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: put_and_unmap_page()
-----BEGIN PGP SIGNATURE-----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=rJlY
-----END PGP SIGNATURE-----
Merge tag 'for-6.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"First batch of fixes. Among them there are two updates to sysfs and
ioctl which are not strictly fixes but are used for testing so there's
no reason to delay them.
- fix block group item corruption after inserting new block group
- fix extent map logging bit not cleared for split maps after
dropping range
- fix calculation of unusable block group space reporting bogus
values due to 32/64b division
- fix unnecessary increment of read error stat on write error
- improve error handling in inode update
- export per-device fsid in DEV_INFO ioctl to distinguish seeding
devices, needed for testing
- allocator size classes:
- fix potential dead lock in size class loading logic
- print sysfs stats for the allocation classes"
* tag 'for-6.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix block group item corruption after inserting new block group
btrfs: fix extent map logging bit not cleared for split maps after dropping range
btrfs: fix percent calculation for bg reclaim message
btrfs: fix unnecessary increment of read error stat on write error
btrfs: handle btrfs_del_item errors in __btrfs_update_delayed_inode
btrfs: ioctl: return device fsid from DEV_INFO ioctl
btrfs: fix potential dead lock in size class loading logic
btrfs: sysfs: add size class stats
Commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new() call-back
type") introduced a new probe callback to convert i2c init routines to
not take an i2c_device_id parameter. Now that all in-tree drivers are
converted to the temporary .probe_new() callback, .probe() can be
modified to match the desired prototype.
Now that .probe() and .probe_new() have the same semantic, they can be
defined as members of an anonymous union to save some memory and
simplify the core code a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XVs0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential out of bound write of zeroes in HID core with a
specially crafted uhid device (Lee Jones)
- fix potential use-after-free in work function in intel-ish-hid (Reka
Norman)
- selftests config fixes (Benjamin Tissoires)
- few device small fixes and support
* tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
HID: logitech-hidpp: Add support for Logitech MX Master 3S mouse
HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
selftest: hid: fix hid_bpf not set in config
HID: uhid: Over-ride the default maximum data buffer value with our own
HID: core: Provide new max_buffer_size attribute to over-ride the default
I was intending to make all the Netlink Spec code BSD-3-Clause
to ease the adoption but it appears that:
- I fumbled the uAPI and used "GPL WITH uAPI note" there
- it gives people pause as they expect GPL in the kernel
As suggested by Chuck re-license under dual. This gives us benefit
of full BSD freedom while fulfilling the broad "kernel is under GPL"
expectations.
Link: https://lore.kernel.org/all/20230304120108.05dd44c5@kernel.org/
Link: https://lore.kernel.org/r/20230306200457.3903854-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 596ff4a09b ("cpumask: re-introduce constant-sized cpumask
optimizations") changed cpumask_setall() to use "bitmap_set()" instead
of "bitmap_fill()", because bitmap_fill() would explicitly set all the
bits of a constant sized small bitmap, and that's exactly what we don't
want: we want to only set bits up to 'nr_cpu_ids', which is what
"bitmap_set()" does.
However, Yury correctly points out that while "bitmap_set()" does indeed
only set bits up to the required bitmap size, it doesn't _clear_ bits
above that size, so the upper bits would still not have well-defined
values.
Now, none of this should really matter, since any bits set past
'nr_cpu_ids' should always be ignored in the first place. Yes, the bit
scanning functions might return them as a result, but since users should
always consider the ">= nr_cpu_ids" condition to mean "no more bits",
that shouldn't have any actual effect (see previous commit 8ca09d5fa3
"cpumask: fix incorrect cpumask scanning result checks").
But let's just do it right, the way the code was _intended_ to work. We
have had enough lazy code that works but bites us in the *rse later
(again, see previous commit) that there's no reason to not just do this
properly.
It turns out that "bitmap_fill()" gets this all right for the complex
case, and really only fails for the inlined optimized case that just
fills the whole word. And while we could just fix bitmap_fill() to use
the proper last word mask, there's two issues with that:
- the cpumask case wants to do the _optimization_ based on "NR_CPUS is
a small constant", but then wants to do the actual bit _fill_ based
on "nr_cpu_ids" that isn't necessarily that same constant
- we have lots of non-cpumask users of bitmap_fill(), and while they
hopefully don't care, and probably would want the proper semantics
anyway ("only set bits up to the limit"), I do not want the cpumask
changes to impact other parts
So this ends up just doing the single-word optimization by hand in the
cpumask code. If our cpumask is fundamentally limited to a single word,
just do the proper "fill in that word" exactly. And if it's the more
complex multi-word case, then the generic bitmap_fill() will DTRT.
This is all an example of how our bitmap function optimizations really
are somewhat broken. They conflate the "this is size of the bitmap"
optimizations with the actual bit(s) we want to set.
In many cases we really want to have the two be separate things:
sometimes we base our optimizations on the size of the whole bitmap ("I
know this whole bitmap fits in a single word, so I'll just use
single-word accesses"), and sometimes we base them on the bit we are
looking at ("this is just acting on bits that are in the first word, so
I'll use single-word accesses").
Notice how the end result of the two optimizations are the same, but the
way we get to them are quite different.
And all our cpumask optimization games are really about that fundamental
distinction, and we'd often really want to pass in both the "this is the
bit I'm working on" (which _can_ be a small constant but might be
variable), and "I know it's in this range even if it's variable" (based
on CONFIG_NR_CPUS).
So this cpumask_setall() implementation just makes that explicit. It
checks the "I statically know the size is small" using the known static
size of the cpumask (which is what that 'small_cpumask_bits' is all
about), but then sets the actual bits using the exact number of cpus we
have (ie 'nr_cpumask_bits')
Of course, in a perfect world, the compiler would have done all the
range analysis (possibly with help from us just telling it that
"this value is always in this range"), and would do all of this for us.
But that is not the world we live in.
While we dream of that perfect world, this does that manual logic to
make it all work out. And this was a very long explanation for a small
code change that shouldn't even matter.
Reported-by: Yury Norov <yury.norov@gmail.com>
Link: https://lore.kernel.org/lkml/ZAV9nGG9e1%2FrV+L%2F@yury-laptop/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The create pipeline message can carry the target code_id which is set to
0 at the moment.
Add macros to set the core_id in the message extension.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230307123556.31328-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Lucas Tanure <lucas.tanure@collabora.com>:
Valve's Steam Deck uses CS35L41 in shared boost mode, where both speakers
share the boost circuit.
Add this support in the shared lib, but for now, shared boost is not
supported in HDA systems as would require BIOS changes.
Based on David Rhodes shared boost patches.
Also, fix boost config overwriting in IRQ found in the review and do a
small refactor of the code.
