mlx5 devices were observed generating MLX5_PORT_CHANGE_SUBTYPE_ACTIVE
events without an intervening MLX5_PORT_CHANGE_SUBTYPE_DOWN. This
breaks link flap detection based on Linux carrier state transition
count as netif_carrier_on() does nothing if carrier is already on.
Make sure we count such events.
netif_carrier_event() increments the counters and fires the linkwatch
events. The latter is not necessary for the use case but seems like
the right thing to do.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.
Changes in v5:
- Update spi_mem_read_status() description.
- Update poll_status() description API by indicating that data buffer is
filled with last status value.
- Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
- Remove parenthesys arount -EINVAL in spi_mem_poll_status().
- Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
- Add Boris Reviewed-by for patch 1 and 2.
Changes in v4:
- Remove init_completion() from spi_mem_probe() added in v2.
- Add missing static for spi_mem_read_status().
- Check if operation in spi_mem_poll_status() is a READ.
- Update patch 2 commit message.
- Add comment which explains how delays has been calculated.
- Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.
Chnages in v3:
- Add spi_mem_read_status() which allows to read 8 or 16 bits status.
- Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
and also to poll_status() callback.
- Move spi_mem_supports_op() in SW-based polling case.
- Add delay before invoquing read_poll_timeout().
- Remove the reinit/wait_for_completion() added in v2.
- Add initial_delay_us and polling_delay_us parameters to spinand_wait().
- Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
- Remove spi_mem_finalize_op() API added in v2.
Changes in v2:
- Indicates the spi_mem_poll_status() timeout unit
- Use 2-byte wide status register
- Add spi_mem_supports_op() call in spi_mem_poll_status()
- Add completion management in spi_mem_poll_status()
- Add offload/non-offload case management in spi_mem_poll_status()
- Optimize the non-offload case by using read_poll_timeout()
- mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
- Make usage of new spi_mem_finalize_op() API in
stm32_qspi_wait_poll_status()
Patrice Chotard (3):
spi: spi-mem: add automatic poll status functions
mtd: spinand: use the spi-mem poll status APIs
spi: stm32-qspi: add automatic poll status feature
drivers/mtd/nand/spi/core.c | 45 +++++++++++++------
drivers/spi/spi-mem.c | 86 ++++++++++++++++++++++++++++++++++++
drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
include/linux/mtd/spinand.h | 22 +++++++++
include/linux/spi/spi-mem.h | 16 +++++++
5 files changed, 234 insertions(+), 21 deletions(-)
base-commit: 6efb943b86
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The ST accelerators support a special type of quirky mounting matrix found
in ACPI systems, but not a generic mounting matrix such as from the device
tree.
Augment the ACPI hack to be a bit more generic and accept a mounting
matrix from device properties.
This makes it possible to fix orientation on the Ux500 HREF device.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Daniel Drake <drake@endlessm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210518230722.522446-2-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extend ST_SENSORS_LSM_CHANNELS() to a version that will accept extended
attributes named ST_SENSORS_LSM_CHANNELS_EXT() and wrap the former as a
specialized version of the former.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Daniel Drake <drake@endlessm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210518230722.522446-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All of the users of iio_read_mount_matrix() are using the very same
property name. Moreover, the property name is hard coded in the API
documentation.
Make this clear and avoid duplication now and in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210518112546.44592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently when mlx4 maps the hca_core_clock page to the user space there
are read-modifiable registers, one of which is semaphore, on this page as
well as the clock counter. If user reads the wrong offset, it can modify
the semaphore and hang the device.
Do not map the hca_core_clock page to the user space unless the device has
been put in a backwards compatibility mode to support this feature.
After this patch, mlx4 core_clock won't be mapped to user space on the
majority of existing devices and the uverbs device time feature in
ibv_query_rt_values_ex() will be disabled.
Fixes: 52033cfb5a ("IB/mlx4: Add mmap call to map the hardware clock")
Link: https://lore.kernel.org/r/9632304e0d6790af84b3b706d8c18732bc0d5e27.1622726305.git.leonro@nvidia.com
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ab8500.h header in linux/power is not referenced/included, so can be
safely removed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove iov_iter_for_each_range() as it's no longer used with the removal of
lustre.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The util_est internal UTIL_AVG_UNCHANGED flag which is used to prevent
unnecessary util_est updates uses the LSB of util_est.enqueued. It is
exposed via _task_util_est() (and task_util_est()).
Commit 92a801e5d5 ("sched/fair: Mask UTIL_AVG_UNCHANGED usages")
mentions that the LSB is lost for util_est resolution but
find_energy_efficient_cpu() checks if task_util_est() returns 0 to
return prev_cpu early.
_task_util_est() returns the max value of util_est.ewma and
util_est.enqueued or'ed w/ UTIL_AVG_UNCHANGED.
So task_util_est() returning the max of task_util() and
_task_util_est() will never return 0 under the default
SCHED_FEAT(UTIL_EST, true).
To fix this use the MSB of util_est.enqueued instead and keep the flag
util_est internal, i.e. don't export it via _task_util_est().
The maximal possible util_avg value for a task is 1024 so the MSB of
'unsigned int util_est.enqueued' isn't used to store a util value.
As a caveat the code behind the util_est_se trace point has to filter
UTIL_AVG_UNCHANGED to see the real util_est.enqueued value which should
be easy to do.
This also fixes an issue report by Xuewen Yan that util_est_update()
only used UTIL_AVG_UNCHANGED for the subtrahend of the equation:
last_enqueued_diff = ue.enqueued - (task_util() | UTIL_AVG_UNCHANGED)
Fixes: b89997aa88 sched/pelt: Fix task util_est update filtering
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Xuewen Yan <xuewen.yan@unisoc.com>
Reviewed-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20210602145808.1562603-1-dietmar.eggemann@arm.com
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With STM32 QSPI, it is possible to poll the status register of the device.
This could be done to offload the CPU during an operation (erase or
program a SPI NAND for example).
spi_mem_poll_status API has been added to handle this feature.
This new function take care of the offload/non-offload cases.
For the non-offload case, use read_poll_timeout() to poll the status in
order to release CPU during this phase.
For example, previously, when erasing large area, in non-offload case,
CPU load can reach ~50%, now it decrease to ~35%.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/r/20210518162754.15940-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds sleepwalk/wake and suspend/resume interfaces
to Tegra XUSB PHY driver.
Tegra XUSB host controller driver makes use of sleepwalk functions
to enable/disable sleepwalk circuit which is in always-on partition
and can respond to USB resume signals when controller is not powered.
Sleepwalk can be enabled/disabled for any USB UPHY individually.
- tegra_xusb_padctl_enable_phy_sleepwalk()
- tegra_xusb_padctl_disable_phy_sleepwalk()
Tegra XUSB host controller driver makes use of wake functions to
enable/disable/query wake circuit which is in always-on partition
can wake system up when USB resume happens.
Wake circuit can be enabled/disabled for any USB PHY individually.
- tegra_xusb_padctl_enable_phy_wake()
- tegra_xusb_padctl_disable_phy_wake()
- tegra_xusb_padctl_remote_wake_detected()
This commit also adds two system suspend stubs that can be used to
save and restore XUSB PADCTL context during system suspend and
resume.
- tegra_xusb_padctl_suspend_noirq()
- tegra_xusb_padctl_resume_noirq()
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The hang_limit is the threshold after which the kernel no longer
attempts to schedule a job. Its documentation stated the opposite due to
a typo. Correct the wording to indicate the actual purpose of the field.
Signed-off-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210528235152.38447-1-alyssa.rosenzweig@collabora.com
Allow the compiler to verify the type of the second argument passed to
scsi_host_complete_all_commands().
Link: https://lore.kernel.org/r/20210524025457.11299-4-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make it possible for the compiler to verify whether SAM and host
status codes are used correctly.
[mkp: resolve conflicts with Hannes' SCSI result series]
Link: https://lore.kernel.org/r/20210524025457.11299-3-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert address.c to use IS_ENABLED() instead of ifdefs for the
public PCI functions. This simplifies the ifdefs in of_address.h.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210527194547.1287934-4-robh@kernel.org
of_get_address() and of_get_pci_address() are the same implementation
except of_get_pci_address() takes the PCI BAR number rather than an
index. Modify the of_get_address() implementation to work on either
index or BAR and provide wrapper functions for the existing functions.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210527194547.1287934-3-robh@kernel.org
Add an empty stub for pci_register_io_range() when !CONFIG_PCI. It's needed
to convert of_pci_range_to_resource() to use IS_ENABLED(CONFIG_PCI).
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210527194547.1287934-2-robh@kernel.org
fdt_init_reserved_mem() and fdt_reserved_mem_save_node() are private to
the DT code, so move there declarations to of_private.h. There's no need
for the dummy functions as CONFIG_OF_RESERVED_MEM is always enabled for
CONFIG_OF_EARLY_FLATTREE.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210527193841.1284169-1-robh@kernel.org
Shiraz Saleem says:
====================
Add Intel Ethernet Protocol Driver for RDMA (irdma)
The following patch series introduces a unified Intel Ethernet Protocol
Driver for RDMA (irdma) for the X722 iWARP device and a new E810 device
which supports iWARP and RoCEv2. The irdma module replaces the legacy
i40iw module for X722 and extends the ABI already defined for i40iw. It is
backward compatible with legacy X722 rdma-core provider (libi40iw).
X722 and E810 are PCI network devices that are RDMA capable. The RDMA
block of this parent device is represented via an auxiliary device
exported to 'irdma' using the core auxiliary bus infrastructure recently
added for 5.11 kernel. The parent PCI netdev drivers 'i40e' and 'ice'
register auxiliary RDMA devices with private data/ops encapsulated that
bind to auxiliary drivers registered in irdma module.
Currently, default is RoCEv2 for E810. Runtime support for protocol switch
to iWARP will be made available via devlink in a future patch.
====================
Link: https://lore.kernel.org/r/20210602205138.889-1-shiraz.saleem@intel.com
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
* branch 'irdma':
RDMA/irdma: Update MAINTAINERS file
RDMA/irdma: Add irdma Kconfig/Makefile and remove i40iw
RDMA/irdma: Add ABI definitions
RDMA/irdma: Add dynamic tracing for CM
RDMA/irdma: Add miscellaneous utility definitions
RDMA/irdma: Add user/kernel shared libraries
RDMA/irdma: Add RoCEv2 UD OP support
RDMA/irdma: Implement device supported verb APIs
RDMA/irdma: Add PBLE resource manager
RDMA/irdma: Add connection manager
RDMA/irdma: Add QoS definitions
RDMA/irdma: Add privileged UDA queue implementation
RDMA/irdma: Add HMC backing store setup functions
RDMA/irdma: Implement HW Admin Queue OPs
RDMA/irdma: Implement device initialization definitions
RDMA/irdma: Register auxiliary driver and implement private channel OPs
i40e: Register auxiliary devices to provide RDMA
i40e: Prep i40e header for aux bus conversion
ice: Register auxiliary device to provide RDMA
ice: Implement iidc operations
ice: Initialize RDMA support
iidc: Introduce iidc.h
i40e: Replace one-element array with flexible-array member
Add Kconfig and Makefile to build irdma driver.
Remove i40iw driver and add an alias in irdma.
Remove legacy exported symbols i40e_register_client
and i40e_unregister_client from i40e as they are no
longer used.
irdma is the replacement driver that supports X722.
Link: https://lore.kernel.org/r/20210602205138.889-16-shiraz.saleem@intel.com
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
This patch defines the new template fields xattrnames, xattrlengths and
xattrvalues, which contain respectively a list of xattr names (strings,
separated by |), lengths (u32, hex) and values (hex). If an xattr is not
present, the name and length are not displayed in the measurement list.
Reported-by: kernel test robot <lkp@intel.com> (Missing prototype def)
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Implement device supported verb APIs. The supported APIs
vary based on the underlying transport the ibdev is
registered as (i.e. iWARP or RoCEv2).
Link: https://lore.kernel.org/r/20210602205138.889-10-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Refactor DEVLINK_CMD_RATE_{GET|SET} command handlers to support setting
a node as a parent for another rate object (leaf or node) by means of
new attribute DEVLINK_ATTR_RATE_PARENT_NODE_NAME. Extend devlink ops
with new callbacks rate_{leaf|node}_parent_set() to set node as a parent
for rate object to allow supporting drivers to implement rate grouping
through devlink. Driver implementations are allowed to support leafs
or node children only. Invoking callback with NULL as parent should be
threated by the driver as unset parent action.
Extend rate object struct with reference counter to disallow deleting a
node with any child pointing to it. User should unset parent for the
child explicitly.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate add netdevsim/netdevsim10/group2
$ devlink port function rate set netdevsim/netdevsim10/group1 parent group2
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node parent group2
$ devlink port function rate set netdevsim/netdevsim10/group1 noparent
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_{NEW|DEL} commands that are used
to create and delete devlink rate nodes. Add new attribute
DEVLINK_ATTR_RATE_NODE_NAME that specify node name string. The node name
is an alphanumeric identifier. No valid node name can be a devlink port
index, eg. decimal number. Extend devlink ops with new callbacks
rate_node_{new|del}() and rate_node_tx_{share|max}_set() to allow
supporting drivers to implement ports rate grouping and setting tx rate
of rate nodes through devlink.
Expose devlink_rate_nodes_destroy() function to allow vendor driver do
proper cleanup of internally allocated resources for the nodes if the
driver goes down or due to any other reasons which requires nodes to be
destroyed.
Disallow moving device from switchdev to legacy mode if any node exists
on that device. User must explicitly delete nodes before switching mode.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate set netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
Add + set command can be combined:
$ devlink port function rate add netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node tx_share 10mbit tx_max 100mbit
$ devlink port function rate del netdevsim/netdevsim10/group1
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_SET command with new attributes
DEVLINK_ATTR_RATE_TX_{SHARE|MAX} that are used to set devlink rate
shared/max tx rate values. Extend devlink ops with new callbacks
rate_leaf_tx_{share|max}_set() to allow supporting drivers to implement
rate control through devlink.
New attributes are optional. Driver implementations are allowed to
support either or both of them.
Shared rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_share 10mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_share 10mbit
Max rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_max 100mbit
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow registering rate object for devlink ports with dedicated
devlink_rate_leaf_{create|destroy}() API. Implement new netlink
DEVLINK_CMD_RATE_GET command that is used to retrieve rate object info.
Add new DEVLINK_CMD_RATE_{NEW|DEL} commands that are used for
notifications when creating/deleting leaf rate object.
Rate API is intended to be used for rate limiting of individual
devlink ports (leafs) and their aggregates (nodes).
Example:
$ devlink port show
pci/0000:03:00.0/0
pci/0000:03:00.0/1
$ devlink port function rate show
pci/0000:03:00.0/0: type leaf
pci/0000:03:00.0/1: type leaf
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for converting SAM status codes into an enum. Without
this patch converting SAM status codes into an enumeration type would
trigger complaints about enum type mismatches for the SAS code.
Link: https://lore.kernel.org/r/20210524025457.11299-2-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With x86_64_defconfig and the following configs, there is an orphan
section warning:
CONFIG_SMP=n
CONFIG_AMD_MEM_ENCRYPT=y
CONFIG_HYPERVISOR_GUEST=y
CONFIG_KVM=y
CONFIG_PARAVIRT=y
ld: warning: orphan section `.data..decrypted' from `arch/x86/kernel/cpu/vmware.o' being placed in section `.data..decrypted'
ld: warning: orphan section `.data..decrypted' from `arch/x86/kernel/kvm.o' being placed in section `.data..decrypted'
These sections are created with DEFINE_PER_CPU_DECRYPTED, which
ultimately turns into __PCPU_ATTRS, which in turn has a section
attribute with a value of PER_CPU_BASE_SECTION + the section name. When
CONFIG_SMP is not set, the base section is .data and that is not
currently handled in any linker script.
Add .data..decrypted to PERCPU_DECRYPTED_SECTION, which is included in
PERCPU_INPUT -> PERCPU_SECTION, which is include in the x86 linker
script when either CONFIG_X86_64 or CONFIG_SMP is unset, taking care of
the warning.
Fixes: ac26963a11 ("percpu: Introduce DEFINE_PER_CPU_DECRYPTED")
Link: https://github.com/ClangBuiltLinux/linux/issues/1360
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com> # build
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210506001410.1026691-1-nathan@kernel.org
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace BIT() in v4l2's UPAI header with _BITUL(). BIT() is not defined
in the UAPI headers and its usage may cause userspace build errors.
Fixes: 206bc0f6fb ("media: vicodec: mark the stateless FWHT API as stable")
Signed-off-by: Joe Richey <joerichey@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the audio_out_delay value is unused, then set it to 1, not 0.
The value 0 is reserved, and 1 is a much safer value since it
translates to a delay of (1 - 1) * 2 = 0 ms.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Samsung PMIC drivers for early chipsets like S5M8767 stored quite a
lot in platform data (struct sec_platform_data). The s5m8767 regulator
driver currently references only some of its fields. Newer regulator
drivers (e.g. s2mps11) use even less platform data fields.
Clean up the structure to reduce memory footprint and source code size.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Set device wakeup capability from devicetree property (done by drivers
core), instead of always setting it to 0 (because value in platform data
is not assigned).
This should not have visible effect on actual resuming from suspend
because the child device - S5M RTC driver - is responsible for waking
up and sets device wakeup unconditionally.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 'irq_base' field of platform data structure is not assigned,
therefore its default value of 0 has no impact and can be safely
dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 'device_type' field of platform data structure is not used and can
be safely dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The 'cfg_pmic_irq' field of platform data structure is not used and can
be safely dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
