During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Map unused registers at the end of DMA region at 64 MB to allow PCI masters
to cross the boundary when prefetching data from SDRAM.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
The commit 14fa43f53f ("ASoC: Only
register AC97 bus if it's not done already") added a condition for
calling of soc_ac97_dev_register() but not added for calling of
soc_ac97_dev_unregister(). This patch adds same condition for
soc_ac97_dev_unregister(). Without this fix, kernel crashes when
unloading an asoc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This follows the ARM change from Aaro Koskinen:
When unmapping N pages (e.g. shared memory) the amount of TLB
flushes done can be (N*PAGE_SIZE/ZAP_BLOCK_SIZE)*N although it
should be N at maximum. With PREEMPT kernel ZAP_BLOCK_SIZE is 8
pages, so there is a noticeable performance penalty when
unmapping a large VMA and the system is spending its time in
flush_tlb_range().
The problem is that tlb_end_vma() is always flushing the full VMA
range. The subrange that needs to be flushed can be calculated by
tlb_remove_tlb_entry(). This approach was suggested by Hugh
Dickins, and is also used by other arches.
The speed increase is roughly 3x for 8M mappings and for larger
mappings even more.
Bits and peices are taken from the ARM patch as well as the existing
arch/um implementation that is quite similar.
The end result is a significant reduction in both partial and full TLB
flushes initiated through flush_tlb_range().
At the same time, the nommu implementation was broken, had a superfluous
cache flush, and subsequently would have triggered a BUG_ON() if a
code-path had triggered it. Tidy this up for correctness and provide a
nopped-out implementation there.
More background on the initial discussion can be found at:
http://marc.info/?t=123609820900002&r=1&w=2http://marc.info/?t=123660375800003&r=1&w=2
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: allow architectures to monitor busses for dma mem leakage
This patch adds checking code to detect if a device has pending DMA
operations when it is about to be unbound from its device driver.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Impact: get notified if a device dma maps illegal areas
This patch adds a check to print a warning message when a device driver
tries to map a memory area from the kernel text segment or rodata.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Impact: saves stacktrace of a dma mapping and prints it if there is an error
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This adds a function to dump the DMA mappings that the debugging code is
aware of -- either for a single device, or for _all_ devices.
This can be useful for debugging -- sticking a call to it in the DMA
page fault handler, for example, to see if the faulting address _should_
be mapped or not, and hence work out whether it's IOMMU bugs we're
seeing, or driver bugs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Impact: avoid recursive kfree calls, less slab activity on heavy load
debugobjects checks on kfree whether tracked objects are freed. When a
tracked object is freed debugobjects frees the internal reference
object as well. The debug object slab cache is marked to not recurse
into debugobjects when a slab objects is freed, but the recursive call
can be problematic versus locking in the memory allocator.
Defer the freeing of debug slab objects via schedule_work. The reasons
not to use RCU are:
1) rcu makes the data structure larger
2) there is no real need for rcu as nothing references the obj after
we freed it
3) under heavy load it is easier to reuse the to be freed objects instead
of allocating new objects from the slab. This lowered the slab activity
significantly in a heavy load networking test where lots of timers are
created/destroyed. The workqueue based delayed free allows us just to
put the to be freed objects back into the object pool and reuse them
right away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <200903162049.58058.nickpiggin@yahoo.com.au>
Impact: refactor/consolidate object management, prepare for delayed free
debugobjects allocates static reference objects to track objects which
are initialized or activated before the slab cache becomes
available. These static reference objects have to be handled
seperately in free_object(). The handling of these objects is in the
way of implementing a delayed free functionality. The delayed free is
required to avoid callbacks into the mm code from
debug_check_no_obj_freed().
Replace the static object references with dynamic ones after the slab
cache has been initialized. The static objects are now marked initdata.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <200903162049.58058.nickpiggin@yahoo.com.au>
There were 3 invocations of task_hot() in can_migrate_task().
Replace these 3 invocations by only one invocation, cached in
a local variable.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090316195902.GA6197@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fixed typos in function documentation.
Signed-off-by: Luis Henriques <henrix@sapo.pt>
LKML-Reference: <20090316195809.GA6073@hades.domain.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: don't trim e820 according to wrong mtrr
Ozan reports that his server emits strange warning.
it turns out the BIOS sets the MTRRs incorrectly.
Ignore those strange ranges, and don't trim e820,
just emit one warning about BIOS
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <49BEE1E7.7020706@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While harmless, PTEA has different semantics on these parts, and is only
used in extended TLB mode. Kill off the legacy support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the OOPS during a opl3sa2 card suspend
and resume if the driver is loaded but the card
is not found.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: fix memory leak
If event_format_read() exits early due to nonzero ppos, the
previous kmalloc doesn't get freed - might as well do the
check before the kmalloc and avoid the problem.
Signed-off-by: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: =?ISO-8859-1?Q?Fr=E9d=E9ric?= Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1237270859.8033.141.camel@charm-linux>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IRQ for sh_eth of sh7763rdp became multi handling.
Therefore, the IRQ number of sh_eth is changed, too.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A number of things that shouldn't be exposed outside the ACPI core
were declared in include/acpi/acpi_drivers.h, where anybody can
see them. This patch moves those declarations to a new "internal.h"
inside drivers/acpi.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use "help" (not "---help---") consistently throughout.
ACPI can't be a module, so if both ACPI & APM are configured,
we use ACPI.
Update pointers to ACPI CA and Linux ACPI projects.
Replace "Compaq" with "Hewlett-Packard" in the spec developer list.
Fix typo in /sys/module path.
The user-space daemon is "acpid", not "acpi".
Add standard "To compile this driver as a module ..." help text.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the generic pci_swizzle_interrupt_pin() instead of ACPI-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Furthermore, we don't need to check for null list entries because we
only add non-null entries.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes whitespace and indentation more consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We found Cx states time abnormal in our some of machines which have 16
LCPUs, the C0 take too many time while system is really idle when kernel
enabled tickless and highres. powertop output is below:
PowerTOP version 1.9 (C) 2007 Intel Corporation
Cn Avg residency P-states (frequencies)
C0 (cpu running) (40.5%) 2.53 Ghz 0.0%
C1 0.0ms ( 0.0%) 2.53 Ghz 0.0%
C2 128.8ms (59.5%) 2.40 Ghz 0.0%
1.60 Ghz 100.0%
Wakeups-from-idle per second : 4.7 interval: 20.0s
no ACPI power usage estimate available
Top causes for wakeups:
41.4% ( 24.9) <interrupt> : extra timer interrupt
20.2% ( 12.2) <kernel core> : usb_hcd_poll_rh_status
(rh_timer_func)
After tacking detailed for this issue, Yakui and I find it is due to 24
bit PM timer overflows when some of cpu sleep more than 4 seconds. With
tickless kernel, the CPU want to sleep as much as possible when system
idle. But the Cx sleep time are recorded by pmtimer which length is
determined by BIOS. The current Cx time was gotten in the following
function from driver/acpi/processor_idle.c:
static inline u32 ticks_elapsed(u32 t1, u32 t2)
{
if (t2 >= t1)
return (t2 - t1);
else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER))
return (((0x00FFFFFF - t1) + t2) & 0x00FFFFFF);
else
return ((0xFFFFFFFF - t1) + t2);
}
If pmtimer is 24 bits and it take 5 seconds from t1 to t2, in above
function, just about 1 seconds ticks was recorded. So the Cx time will be
reduced about 4 seconds. and this is why we see above powertop output.
To resolve this problem, Yakui and I use ktime_get() to record the Cx
states time instead of PM timer as the following patch. the patch was
tested with i386/x86_64 modes on several platforms.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Yakui.zhao <yakui.zhao@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: fix for losing comms in trace
The command lines of tasks are cached at sched switch to not need
to record them at every trace point. Disabling the tracing on stops
the recording of traces, but does not stop the caching of command lines.
When the tracing is off the cache may overflow and cause the tracing
to show incorrect tasks matching the PIDs.
This patch disables prevents updates to the comm cache when the ring buffer
is off.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: fix to one cause of incorrect comm outputs in trace
The spinlock only protected the creation of a comm <=> pid pair.
But it was possible that a reader could look up a pid, and get the
wrong comm because it had no locking.
This also required changing trace_find_cmdline to copy the comm cache
and not just send back a pointer to it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
This is for Red Hat bug 490026: EXT4 panic, list corruption in
ext4_mb_new_inode_pa
ext4_lock_group(sb, group) is supposed to protect this list for
each group, and a common code flow to remove an album is like
this:
ext4_get_group_no_and_offset(sb, pa->pa_pstart, &grp, NULL);
ext4_lock_group(sb, grp);
list_del(&pa->pa_group_list);
ext4_unlock_group(sb, grp);
so it's critical that we get the right group number back for
this prealloc context, to lock the right group (the one
associated with this pa) and prevent concurrent list manipulation.
however, ext4_mb_put_pa() passes in (pa->pa_pstart - 1) with a
comment, "-1 is to protect from crossing allocation group".
This makes sense for the group_pa, where pa_pstart is advanced
by the length which has been used (in ext4_mb_release_context()),
and when the entire length has been used, pa_pstart has been
advanced to the first block of the next group.
However, for inode_pa, pa_pstart is never advanced; it's just
set once to the first block in the group and not moved after
that. So in this case, if we subtract one in ext4_mb_put_pa(),
we are actually locking the *previous* group, and opening the
race with the other threads which do not subtract off the extra
block.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add a mount option which allows the user to disable automatic
allocation of blocks whose allocation by delayed allocation when the
file was originally truncated or when the file is renamed over an
existing file. This feature is intended to save users from the
effects of naive application writers, but it reduces the effectiveness
of the delayed allocation code. This mount option disables this
safety feature, which may be desirable for prodcutions systems where
the risk of unclean shutdowns or unexpected system crashes is low.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Impact: fix a dynamic tracing failure
Recently, the function and function graph tracers failed to use dynamic
tracing after the following commit:
fa9d13cf13
(ftrace: don't try to __ftrace_replace_code on !FTRACE_FL_CONVERTED rec)
The patch is right except a mistake on the check for the FTRACE_FL_CONVERTED
flag. The code patching is aborted in case of successfully nopped sites.
What we want is the opposite: ignore the callsites that haven't been nopped.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: fix crash on VMI (VMware)
When we generate a call sequence for calling a paravirtualized
function, we presume that the generated code is "call *0xXXXXX",
which is a 6 byte opcode; this is larger than a normal
direct call, and so we can patch a direct call over it.
At the moment, however we give gcc enough rope to hang us by
putting the address in a register and generating a two byte
indirect-via-register call. Prevent this by explicitly
dereferencing the function pointer and passing it into the
asm as a constant.
This prevents crashes in VMI, as it cannot handle unpatchable
callsites.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Alok Kataria <akataria@vmware.com>
LKML-Reference: <49BEEDC2.2070809@goop.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
With arch/sh/drivers/dma/ always being built, the Dreamcast DMA engines
are being unconditionally built in, regardless of whether the DMA API is
enabled or not. This is a regression from previous behaviour, but there
is not much advantage in building them all in unconditionally regardless.
Add a new config option to make it optional, and update the only user of
it to reflect that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is trivial to merge the non-MMU and MMU versions of siginfo.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of siginfo.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The MMU version of unistd.h can be use on non-MMU platrorms as well.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of unistd.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of signal.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of signal.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It is trivial to merge the non-MMU and MMU versions of ptrace.h.
Without a single file "make headers_install" is broken for m68k
(since each of the sub-varients of ptrace.h are not installed).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>