* Update reset and sync with HALs
* Clean up eeprom settings and tweaking of initvals and
put them on separate functions
* Set/Restore 32KHz ref clk operation
* Add some more documentation
TODO: Spur mitigation, tpc, half/quarter rate, compression etc
v2: Address comments from Bob and Felix and fix RSSI threshold bug
introduced on the first version of the patch
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update initvals to match legacy and Sam's HAL
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use the new way to modify rf buffer and put some rf buffer
documentation on rfbufer.h
* Merge all rf regs functions to one
* Sync with legacy HAL and Sam's HAL
* Set gain_F settings so that gain_F optimization engine works
on RF5111/RF5112 (note that both HALs only use step 0 for RF5111
and they don't use gain_F optimization for this chip, code is
there but is never used)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update and cleanup rf gain optimization code
* Add comments and refferences to docs and use sane function names
* Use only step index on ath5k_gain, no need to have a pointer to
the current step since we can determine te step from it's index,
this also allows us to put all other structs on rfgain.h and cleanup
ath5k.h a little
* No need for ah_rfgain variable, we use ah_gain.g_state for everything
* Tested on RF2112B chip but gain_F calibration is not yet done
(we will finish this on the next patch where we'll rewrite rf-buffer
handling)
* Use initial rf gain settings for 2316 and 2317 SoCs introduced on a previous patch
It seems big but it's mostly cleanup, very few functional changes have been made on phy.c
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up initial rf buffer settings (new file rfbufer.h) and introduce a
new way to access specific rf registers (will use it later)
* Clean up initial rf gain settings by moving them on a new file (rfgain.h)
so we can later work on gain optimization functions
* Update initial rf buffer settings and initial rf gain settings from HALs.
This breaks things for now because our current dumps come from pre-configured
rf buffer (regdumps already had the needed values set from binary HAL).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The atomic requirement for the TSF callbacks
is outdated. get_tsf() is only called by
ieee80211_rx_bss_info() which is indirectly
called by the work queue ieee80211_sta_work().
In the same context are called several other
non-atomic functions, too.
And the atomic requirement causes problems
for drivers of USB wifi cards.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just compile it into the orinoco module. If we merge USB support, the
module can then be split as appropriate.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... when used by the WEXT ioctl functions. This will allow us to
separate the card specific stuff from the WEXT code.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The uv_hub_send_ipi() function needs to set the full apicid in the
UVH_IPI_INT mmr.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Only register AC97 bus if it's not done already
ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
ALSA: hda - Add missing terminator in slave dig-out array
ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
ALSA: hda - Register (new) devices at reconfig
ALSA: mtpav - Fix initial value for input hwport
ALSA: hda - add id for Intel IbexPeak integrated HDMI codec
ALSA: hda - compute checksum in HDMI audio infoframe
ALSA: hda - enable HDMI audio pin out at module loading time
ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
ASoC: Update SDP3430 machine driver for snd_soc_card
ALSA: hda - Add quirk for Asus z37e (1043:8284)
sound: Remove OSSlib stuff from linux/soundcard.h
ASoC: WM8990: Fix kcontrol's private value use in put callback
ASoC: TLV320AIC3X: Fix kcontrol's private value use in put callback
uids in namespaces other than init don't get a sysfs entry.
For those in the init namespace, while we're waiting to remove
the sysfs entry for the uid the uid is still hashed, and
alloc_uid() may re-grab that uid without getting a new
reference to the user_ns, which we've already put in free_user
before scheduling remove_user_sysfs_dir().
Reported-and-tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the c/p state "power" tracer to use tracepoints. Avoids a
function call when the tracer is disabled.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
ASoC supports both explicit codec drivers for AC97 devices and a simple
driver which uses the standard ALSA AC97 framework for codec support.
When used with the generic AC97 codec support that will provide the
ad hoc AC97 device for drivers like touchscreens to attach to so the
core shouldn't do so.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the CS4270 codec driver to allow applications to use the mixer to
control Digital Loopback, Soft Ramp, Zero Cross, Popguard, and Auto-Mute.
Soft Ramp, Zero Cross, and Auto-Mute are disabled by the driver when it first
initializes the hardware, but these features either don't work or interfere
with normal ALSA behavior. However, they can now be re-enabled by an
application if desired.
Remove CONFIG_SND_SOC_CS4270_HWMUTE and always allow ASoC to control the mute
bits. The driver previously and erroneously assumed that these bits
control only external muting circuitry, but they also control internal
muting circuitry, so they should always be used.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit
commit 4595f9620c
Author: Rusty Russell <rusty@rustcorp.com.au>
Date: Sat Jan 10 21:58:09 2009 -0800
x86: change flush_tlb_others to take a const struct cpumask
causes xen_flush_tlb_others to allocate a multicall and then issue it
without initializing it in the case where the cpumask is empty,
leading to:
[ 8.354898] 1 multicall(s) failed: cpu 1
[ 8.354921] Pid: 2213, comm: bootclean Not tainted 2.6.29-rc3-x86_32p-xenU-tip #135
[ 8.354937] Call Trace:
[ 8.354955] [<c01036e3>] xen_mc_flush+0x133/0x1b0
[ 8.354971] [<c0105d2a>] ? xen_force_evtchn_callback+0x1a/0x30
[ 8.354988] [<c0105a60>] xen_flush_tlb_others+0xb0/0xd0
[ 8.355003] [<c0126643>] flush_tlb_page+0x53/0xa0
[ 8.355018] [<c0176a80>] do_wp_page+0x2a0/0x7c0
[ 8.355034] [<c0238f0a>] ? notify_remote_via_irq+0x3a/0x70
[ 8.355049] [<c0178950>] handle_mm_fault+0x7b0/0xa50
[ 8.355065] [<c0131a3e>] ? wake_up_new_task+0x8e/0xb0
[ 8.355079] [<c01337b5>] ? do_fork+0xe5/0x320
[ 8.355095] [<c0121919>] do_page_fault+0xe9/0x240
[ 8.355109] [<c0121830>] ? do_page_fault+0x0/0x240
[ 8.355125] [<c032457a>] error_code+0x72/0x78
[ 8.355139] call 1/1: op=2863311530 arg=[aaaaaaaa] result=-38 xen_flush_tlb_others+0x41/0xd0
Since empty cpumasks are rare and undoing an xen_mc_entry() is tricky
just issue such requests normally.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While reviewing the manpages, I noticed I'd missed some clock vs timer sites.
Make sure that all timer functions call cpu_timer_sample_group() and not
cpu_clock_sample_group(). This ensures that we enable the process wide timer
in time, and therefore pay the O(n) thread group cost from the syscall.
Not doing it here, will result in the first jiffy tick after setting the timer
doing this, resulting in a very expensive tick (but only once) and a delay in
actually starting the timer.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jaswinder Singh Rajput reported that commit 23a185ca8a caused the
context switch and migration software counters to report zero always.
With that commit, the software counters only count events that occur
between sched-in and sched-out for a task. This is necessary for the
counter enable/disable prctls and ioctls to work. However, the
context switch and migration counts are incremented after sched-out
for one task and before sched-in for the next. Since the increment
doesn't occur while a task is scheduled in (as far as the software
counters are concerned) it doesn't count towards any counter.
Thus the context switch and migration counters need to count events
that occur at any time, provided the counter is enabled, not just
those that occur while the task is scheduled in (from the perf_counter
subsystem's point of view). The problem though is that the software
counter code can't tell the difference between being enabled and being
scheduled in, and between being disabled and being scheduled out,
since we use the one pair of enable/disable entry points for both.
That is, the high-level disable operation simply arranges for the
counter to not be scheduled in any more, and the high-level enable
operation arranges for it to be scheduled in again.
One way to solve this would be to have sched_in/out operations in the
hw_perf_counter_ops struct as well as enable/disable. However, this
takes a simpler approach: it adds a 'prev_state' field to the
perf_counter struct that allows a counter's enable method to know
whether the counter was previously disabled or just inactive
(scheduled out), and therefore whether the enable method is being
called as a result of a high-level enable or a schedule-in operation.
This then allows the context switch, migration and page fault counters
to reset their hw.prev_count value in their enable functions only if
they are called as a result of a high-level enable operation.
Although page faults would normally only occur while the counter is
scheduled in, this changes the page fault counter code too in case
there are ever circumstances where page faults get counted against a
task while its counters are not scheduled in.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added the support of multiple digital outputs via auto-probing for
Realtek ALC88x codecs. The multiple outputs are handled as slave
streams, so only one PCM stream (and the corresponding IEC958*
elements) is provided to control both digital outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup. This call is needed in cases
the codec supports multiple digital outputs as slaves. Otherwise the
slave widgets aren't properly cleaned up.
For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
request_irq() calls into proc code via __setup_irq() which is not safe
in an atomic context, so request_irq() can itself use the more
reliable GFP_KERNEL allocation for the action descriptor.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>