Instead of sending USB commands for every stats call, collect
them once, when status is updated. As the frontend kthread
will call it on every few seconds, the stats will still be
collected.
Besides reducing the amount of USB/I2C transfers, this also
warrants that all stats will be collected at the same time,
and makes easier to convert it to DVBv5 stats in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In cases where the number of tx rings is not a multiple of the number of
rx rings, the tx completion event will be handled on a different core
from the transmit and population of the ring. Races on the ring will
lead to a double-free of the page, and possibly other corruption.
The rings are initialized by default with a valid multiple of rings,
based on the number of cpus, therefore an invalid configuration requires
ethtool to change the ring layout. For instance 'ethtool -L eth0 rx 9 tx
8' will cause packets received on rx0, and XDP_TX'd to tx48, to be
completed on cpu3 (48 % 9 == 3).
Resolve this discrepancy by shifting the irq for the xdp tx queues to
start again from 0, modulo rx_ring_num.
Fixes: 9ecc2d8617 ("net/mlx4_en: add xdp forwarding and data write support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
qed: Fix dependencies and warnings series
The first patch in this series follows Dan Carpenter's reports about
Smatch warnings for recent qed additions and fixes those.
The second patch is the most significant one [and the reason this is
ntended for 'net'] - it's based on Arnd Bermann's suggestion for fixing
compilation issues that were introduced with the roce addition as a result
of certain combinations of qed, qede and qedr Kconfig options.
The third follows the discussion with Arnd and clears a lot of the warnings
that arise when compiling the drivers with "C=1".
Please consider applying this series to 'net'.
====================
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans many of the warnings that would arise in qed as a
result of compilations with C=1; Most of those are the addition
of missing 'static' to functions, although there are several other
fixes as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qedr driver would require a tristate Kconfig option [to allow
it to compile as a module], and toward that end we've added the
INFINIBAND_QEDR option. But as we've made the compilation of the
qed/qede infrastructure required for RoCE dependent on the option
we'd be facing linking difficulties in case that QED=y or QEDE=y,
and INFINIBAND_QEDR=m.
To resolve this, we seperate between the INFINIBAND_QEDR option
and the infrastructure support in qed/qede by introducing a new
QED_RDMA option which would be selected by INFINIBAND_QEDR but would
be a boolean instead of a tristate; Following that, the qed/qede is
fixed based on this new option so that all config combinations would
be supported.
Fixes: cee9fbd8e2 ("qede: add qedr framework")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch compains about qed_roce_ll2_tx() dereference
of the 'cdev' variable while testing its validity later.
As the validation checking is an over-kill [variable would always
be set], simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the commit 9207f9d45b ("net: preserve IP control block
during GSO segmentation"), the GSO CB and the IPoIB CB conflict.
That destroy the IPoIB address information cached there,
causing a severe performance regression, as better described here:
http://marc.info/?l=linux-kernel&m=146787279825501&w=2
This change moves the data cached by the IPoIB driver from the
skb control lock into the IPoIB hard header, as done before
the commit 936d7de3d7 ("IPoIB: Stop lying about hard_header_len
and use skb->cb to stash LL addresses").
In order to avoid GRO issue, on packet reception, the IPoIB driver
stash into the skb a dummy pseudo header, so that the received
packets have actually a hard header matching the declared length.
To avoid changing the connected mode maximum mtu, the allocated
head buffer size is increased by the pseudo header length.
After this commit, IPoIB performances are back to pre-regression
value.
v2 -> v3: rebased
v1 -> v2: avoid changing the max mtu, increasing the head buf size
Fixes: 9207f9d45b ("net: preserve IP control block during GSO segmentation")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=7krl
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20161013' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
This set of patches contains a bunch of fixes:
(1) Fix use of kunmap() after change from kunmap_atomic() within AFS.
(2) Don't use of ERR_PTR() with an always zero value.
(3) Check the right error when using ip6_route_output().
(4) Be consistent about whether call->operation_ID is BE or CPU-E within
AFS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani says:
====================
act_mirred: Ingress actions support
This patch series implements action mirred 'ingress' actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
v4:
in 4/4, check ret code of netif_receive_skb, as suggested by Cong Wang
v3:
in 4/4, addressed non coherency due to reading m->tcfm_eaction multiple
times, as spotted by Eric Dumazet
v2:
in 1/4, declare tcfm_mac_header_xmit as bool instead of int
====================
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, 'action mirred' supported only egress actions (either
TCA_EGRESS_REDIR or TCA_EGRESS_MIRROR).
This patch implements the corresponding ingress actions
TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR.
This allows attaching filters whose target is to hand matching skbs into
the rx processing of a specified device.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.
'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.
As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move detection logic that tests whether device expects skb data to point
at mac_header upon xmit into a function.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'tcfm_ok_push' specifies whether a mac_len sized push is needed upon
egress to the target device (if action is performed at ingress).
Rename it to 'tcfm_mac_header_xmit' as this is actually an attribute of
the target device (and use a bool instead of int).
This allows to decouple the attribute from the action to be taken.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver only has runtime but no build time dependency with FSL_SOC ||
ARCH_MXC || ARCH_LAYERSCAPE. So it can be built for testing purposes if
the COMPILE_TEST option is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is registered via OF, the OF table is used to match the
driver instead of the SPI device ID table, but the entries in the later
are used as aliasses to load the module if the driver was not built-in.
This is because the SPI core always reports an SPI module alias instead
of an OF one, but that could change so it's better to always export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is built as a module, module alias information isn't filled
so the module won't be autoloaded. Add a SPI device ID table and use the
MODULE_DEVICE_TABLE() macro so the information is exported in the module.
Before this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
$
After this patch:
$ modinfo drivers/net/wan/slic_ds26522.ko | grep alias
alias: spi:ds26522
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed ("net IPv6 : Fix broken IPv6 routing table after loopback down-up")
Fixes: a881ae1f62 ("ipv6: don't call addrconf_dst_alloc again when enable lo")
Fixes: 33d99113b1 ("ipv6: reallocate addrconf router for ipv6 address when lo device up")
Reported-by: Francesco Santoro <francesco.santoro@6wind.com>
Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com>
CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Weilong Chen <chenweilong@huawei.com>
CC: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6ae23ad362.
The code has been in kernel since 4.4 but there are no in tree
code that uses. Unused code is broken code, remove it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When i2c-core doesn't find the IRQ associated to the GPIO because
the gpiochip is not available, it assigns -EPROBE_DEFER to the irq.
We need to bail out there and on any other error in an IRQ.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit a485923efb ("HID: i2c-hid: Add support for ACPI
GPIO interrupts") and commit a7d2bf25a4 ("HID: i2c-hid: Do not fail
probing if gpiolib is not enabled") at the same time.
Since commit c884fbd452 ("gpio / ACPI: Add support for retrieving
GpioInt resources from a device") i2c_core already set the IRQ by
looking into the ACPI tree and retrieving the gpioInt. So we just
have some boiler-plate here that is not needed anymore.
The only downside effect here is that now we are not exiting early
enough if the irq is set to -EPROBE_DEFER or any other error, but
this is going to be fixed in the following patch.
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel
endpoints.") introduces support for wildcards in tunnels endpoints,
but in some rare circumstances ip6_tnl_lookup selects wrong tunnel
interface relying only on source or destination address of the packet
and not checking presence of wildcard in tunnels endpoints. Later in
ip6_tnl_rcv this packets can be dicarded because of difference in
ipproto even if fallback device have proper ipproto configuration.
This patch adds checks of wildcard endpoint in tunnel avoiding such
behavior
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Signed-off-by: Vadim Fedorenko <junk@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout loop terminates when the loop count is zero, but the decrement
of the count variable is post check. So count is -1 when we check for the
timeout and therefor the error message is supressed.
Change it to predecrement, so the error message is emitted.
[ tglx: Massaged changelog ]
Fixes: a2c2251012 ("irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20161014072534.GA15168@mwanda
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The J-Core AIC does not have separate interrupt numbers reserved for
cpu-local vs global interrupts. Instead, the driver requesting the irq
is expected to know whether its device uses per-cpu interrupts or not.
Previously it was assumed that handle_simple_irq could work for both
cases, but it intentionally drops interrupts for an irq number that
already has a handler running. This resulted in the timer interrupt
for one cpu being lost when multiple cpus' timers were set for
approximately the same expiration time, leading to stalls. In theory
the same could also happen with IPIs.
To solve the problem, instead of registering handle_simple_irq as the
handler, register a wrapper function which checks whether the irq to
be handled was requested as per-cpu or not, and passes it to
handle_simple_irq or handle_percpu_irq accordingly.
Fixes: 981b58f66c ("irqchip/jcore-aic: Add J-Core AIC driver")
Signed-off-by: Rich Felker <dalias@libc.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/f18cec30bc17e3f52e478dd9f6714bfab02f227f.1476390724.git.dalias@libc.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
===============================
[ INFO: suspicious RCU usage. ]
4.8.0+ #24 Not tainted
-------------------------------
./arch/x86/include/asm/msr-trace.h:47 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
no locks held by swapper/1/0.
[<ffffffff9d492b95>] do_trace_write_msr+0x135/0x140
[<ffffffff9d06f860>] native_write_msr+0x20/0x30
[<ffffffff9d065fad>] native_apic_msr_eoi_write+0x1d/0x30
[<ffffffff9d05bd1d>] smp_reschedule_interrupt+0x1d/0x30
[<ffffffff9d8daec6>] reschedule_interrupt+0x96/0xa0
Reschedule interrupt may be called in cpu idle state. This causes lockdep
check warning above.
Add irq_enter/exit() in smp_reschedule_interrupt(), irq_enter() tells the RCU
subsystems to end the extended quiescent state, so the following trace call in
ack_APIC_irq() works correctly.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
Link: http://lkml.kernel.org/r/1476409733-5133-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since "Dynamic page table allocations" were introduced, our page tables
can grow (being dynamically allocated) with address space range usage.
Unfortunately, their lifetime is bound to vm. This is not a huge problem
when we're not using softpin - drm_mm is creating an upper bound on used
range by causing addresses for our VMAs to eventually be reused.
With softpin, long lived contexts can drain the system out of memory
even with a single "small" object. For example:
bo = bo_alloc(size);
while(true)
offset += size;
exec(bo, offset);
Will cause us to create new allocations until all memory in the system
is used for tracking GPU pages (even though almost all PTEs in this vm
are pointing to scratch).
Let's free unused page tables in clear_range to prevent this - if no
entries are used, we can safely free it and return this information to
the caller (so that higher-level entry is pointing to scratch).
v2: Document return value and free semantics (Joonas)
v3: No newlines in vars block (Joonas)
v4: Drop redundant local 'reduce' variable
v5: Handle CI fail with enable_ppgtt=2
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1476360162-24062-3-git-send-email-michal.winiarski@intel.com
Let's use more top-down approach, where each gen8_ppgtt_clear_* function
is responsible for clearing the struct passed as an argument and calling
relevant clear_range functions on lower-level tables.
Doing this rather than operating on PTE ranges makes the implementation
of shrinking page tables quite simple.
v2: Drop min when calculating num_entries, no negation in 48b ppgtt
check, no newlines in vars block (Joonas)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1476360162-24062-2-git-send-email-michal.winiarski@intel.com
We never used any invalid ptes, those were put in place for
a possibility of doing gpu faults. However our batchbuffers are not
restricted in length, so everything needs to be pointing to something
and thus out-of-bounds is pointing to scratch.
Remove the valid flag as it is always true.
v2: Expand commit msg, patch reorder (Mika)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1476360162-24062-1-git-send-email-michal.winiarski@intel.com
Currently the display INIT power domain disabling/enabling happens in a
mismatched way in the suspend/resume_early hooks respectively. This can
leave display power wells incorrectly disabled in the resume hook if the
suspend sequence is aborted for some reason resulting in the
suspend/resume hooks getting called but the suspend_late/resume_early
hooks being skipped. In particular this change fixes "Unclaimed read
from register 0x1e1204" on BYT/BSW triggered from i915_drm_resume()->
intel_pps_unlock_regs_wa() when suspending with /sys/power/pm_test set
to devices.
Fixes: 85e9067933 ("drm/i915: disable power wells on suspend")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: David Weinehall <david.weinehall@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476358446-11621-1-git-send-email-imre.deak@intel.com
Saves 944 bytes of .rodata strings and 128 bytes of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Saves 864 bytes of .rodata strings and ~100 of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Saves 1392 bytes of .rodata strings.
Also change a few function/macro prototypes in i915_gem_gtt.c
from dev to dev_priv where it made more sense to do so.
v2: Add parantheses around dev_priv. (Ville Syrjala)
v3: Mention function prototype changes. (David Weinehall)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Saves 1016 bytes of .rodata strings and couple hundred of .text.
v2: Add parantheses around dev_priv. (Ville Syrjala)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
