The PID algorithm used by the intel_pstate driver tends to drive
performance to the minimum for workloads with utilization below the
setpoint, which is undesirable, so replace it with a modified
"proportional" algorithm on Atom.
The new algorithm will set the new P-state to be 1.25 times the
available maximum times the (frequency-invariant) utilization during
the previous sampling period except when the target P-state computed
this way is lower than the average P-state during the previous
sampling period. In the latter case, it will increase the target by
50% of the difference between it and the average P-state to prevent
performance from dropping down too fast in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This set of changes contains support for PWM signal capture in the STi
driver as well as support for the PWM controller found on Meson SoCs.
There's also support added for the MediaTek MT2701 and SunXi H3 to the
existing drivers.
Other than that there's a fair set of miscellaneous cleanups and fixes
across the board.
-----BEGIN PGP SIGNATURE-----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=KuVk
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes contains support for PWM signal capture in the STi
driver as well as support for the PWM controller found on Meson SoCs.
There's also support added for the MediaTek MT2701 and SunXi H3 to the
existing drivers.
Other than that there's a fair set of miscellaneous cleanups and fixes
across the board"
* tag 'pwm/for-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (24 commits)
pwm: meson: Handle unknown ID values
pwm: sti: Take the opportunity to conduct a little house keeping
pwm: sti: It's now valid for number of PWM channels to be zero
pwm: sti: Add PWM capture callback
pwm: sti: Add support for PWM capture interrupts
pwm: sti: Initialise PWM capture device data
pwm: sti: Supply PWM Capture clock handling
pwm: sti: Supply PWM capture register addresses and bit locations
pwm: sti: Only request clock rate when needed
pwm: sti: Reorganise register names in preparation for new functionality
pwm: sti: Rename channel => device
dt-bindings: pwm: sti: Update DT bindings for capture support
pwm: lpc-18xx: use pwm_set_chip_data
pwm: sunxi: Add H3 support
pwm: Add support for Meson PWM Controller
dt-bindings: pwm: Add bindings for Meson PWM Controller
pwm: samsung: Fix to use lowest div for large enough modulation bits
pwm: pwm-tipwmss: Remove all runtime PM gets/puts
pwm: cros-ec: Add __packed to prevent padding
pwm: Add MediaTek MT2701 display PWM driver support
...
The error checking here is messed up so we could end up dereferencing
-EFAULT.
Fixes: a16039cbf1 ('ALSA: line6: Add hwdep interface to access the POD control messages')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a fix for Linux 4.9-rc1.
In former commit, a function call of compatibility layer for ALSA sequencer
core was obsoleted by an alternative. Although, the alternative gets a
pointer to kernel stack due to mis-programming. As a result, ALSA sequencer
core unexpectedly refers over kernel stack.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8ce8eb601c ("ALSA: seq: add an alternative way to handle ioctl requests")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a Dell laptop, there is no global adcs for all input devices, so
the input devices use the different adc, as a result, dyn_adc_switch
is set to true.
In this situation, it is safe to control the micmute led according to
user's choice of muting/unmuting the current input device, since only
current input device path is active, while other input device paths
are inactive and powered down.
Fixes: 00ef99408b ('ALSA: hda - add mic mute led hook for dell machines')
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
This affectively reverts commit 377ccbb483 ("Makefile: Mute warning
for __builtin_return_address(>0) for tracing only") because it turns out
that it really isn't tracing only - it's all over the tree.
We already also had the warning disabled separately for mm/usercopy.c
(which this commit also removes), and it turns out that we will also
want to disable it for get_lock_parent_ip(), that is used for at least
TRACE_IRQFLAGS. Which (when enabled) ends up being all over the tree.
Steven Rostedt had a patch that tried to limit it to just the config
options that actually triggered this, but quite frankly, the extra
complexity and abstraction just isn't worth it. We have never actually
had a case where the warning is actually useful, so let's just disable
it globally and not worry about it.
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a sysfs attribute that contains salient information about the NVMe
Controller Memory Buffer when one is present. For now, just display the
information about the CMB available from the control registers. We attach
the CMB attribute file to the existing nvme_ctrl sysfs group so it can
handle the sysfs teardown.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Stephen Bates <sbates@raithlin.com>
Acked-by Jon Derrick: <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add mount option "max_credits" to allow setting maximum SMB3
credits to any value from 10 to 64000 (default is 32000).
This can be useful to workaround servers with problems allocating
credits, or to throttle the client to use smaller amount of
simultaneous i/o or to workaround server performance issues.
Also adds a cap, so that even if the server granted us more than
65000 credits due to a server bug, we would not use that many.
Signed-off-by: Steve French <steve.french@primarydata.com>
Continuous Availability features like persistent handles
require that clients reconnect their open files, not
just the sessions, soon after the network connection comes
back up, otherwise the server will throw away the state
(byte range locks, leases, deny modes) on those handles
after a timeout.
Add code to reconnect handles when use_persistent set
(e.g. Continuous Availability shares) after tree reconnect.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Germano Percossi <germano.percossi@citrix.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Remove the global file_list_lock to simplify cifs/smb3 locking and
have spinlocks that more closely match the information they are
protecting.
Add new tcon->open_file_lock and file->file_info_lock spinlocks.
Locks continue to follow a heirachy,
cifs_socket --> cifs_ses --> cifs_tcon --> cifs_file
where global tcp_ses_lock still protects socket and cifs_ses, while the
the newer locks protect the lower level structure's information
(tcon and cifs_file respectively).
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <steve.french@primarydata.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reviewed-by: Germano Percossi <germano.percossi@citrix.com>
Patch a6b5058 results in -EREMOTE returned by is_path_accessible() in
cifs_mount() to be ignored which breaks DFS mounting.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
When we open a durable handle we give a Globally Unique
Identifier (GUID) to the server which we must keep for later reference
e.g. when reopening persistent handles on reconnection.
Without this the GUID generated for a new persistent handle was lost and
16 zero bytes were used instead on re-opening.
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
GUIDs although random, and 16 bytes, need to be generated as
proper uuids.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Reported-by: David Goebels <davidgoe@microsoft.com>
CC: Stable <stable@vger.kernel.org>
The kernel client requests 2 credits for many operations even though
they only use 1 credit (presumably to build up a buffer of credit).
Some servers seem to give the client as much credit as is requested. In
this case, the amount of credit the client has continues increasing to
the point where (server->credits * MAX_BUFFER_SIZE) overflows in
smb2_wait_mtu_credits().
Fix this by throttling the credit requests if an set limit is reached.
For async requests where the credit charge may be > 1, request as much
credit as what is charged.
The limit is chosen somewhat arbitrarily. The Windows client
defaults to 128 credits, the Windows server allows clients up to
512 credits (or 8192 for Windows 2016), and the NetApp server
(and at least one other) does not limit clients at all.
Choose a high enough value such that the client shouldn't limit
performance.
This behavior was seen with a NetApp filer (NetApp Release 9.0RC2).
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
In debugging smb3, it is useful to display the number
of credits available, so we can see when the server has not granted
sufficient operations for the client to make progress, or alternatively
the client has requested too many credits (as we saw in a recent bug)
so we can compare with the number of credits the server thinks
we have.
Add a /proc/fs/cifs/DebugData line to display the client view
on how many credits are available.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reported-by: Germano Percossi <germano.percossi@citrix.com>
CC: Stable <stable@vger.kernel.org>
Add parsing for new pseudo-xattr user.cifs.creationtime file
attribute to allow backup and test applications to view
birth time of file on cifs/smb3 mounts.
Signed-off-by: Steve French <steve.french@primarydata.com>
Add parsing for new pseudo-xattr user.cifs.dosattrib file attribute
so tools can recognize what kind of file it is, and verify if common
SMB3 attributes (system, hidden, archive, sparse, indexed etc.) are
set.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Pavel Shilovsky <pshilovsky@samba.org>
Treat a framebuffer reference with the same priority as an active
reference whilst shrinking. Framebuffers are likely to be reused and
typically cost more to migrate to and from GPU memory (on LLC
architectures we need to clflush), so defer the temptation to purge them
during a kswapd run until we have run out of cheap buffers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: John Harrison <john.c.harrison@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012124824.23521-1-chris@chris-wilson.co.uk
The current meaning of whether an object has a GGTT vma is very
ill-defined (and note we don't check for any partials either), it just
means that at some point it was in the GGTT but it may not be now. The
information we really care about here is whether it is taking up
precious mappable aperture space. This is the obj->fault_mappable flag.
We have a redundant long form reprinting of this information, so remove
that in favour of the compact flag.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012114827.17031-2-chris@chris-wilson.co.uk
The queue_work only fails if the work is pending, but not yet running. If
the work is running, the work item would get requeued, triggering a
double reset. If the first reset fails for any reason, the second
reset triggers:
WARN_ON(dev->ctrl.state == NVME_CTRL_RESETTING)
Hitting that schedules controller deletion for a second time, which
potentially takes a reference on the device that is being deleted.
If the reset occurs at the same time as a hot removal event, this causes
a double-free.
This patch has the reset helper function check if the work is busy
prior to queueing, and changes all places that schedule resets to use
this function. Since most users don't want to sync with that work, the
"flush_work" is moved to the only caller that wants to sync.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg<sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The driver was decrementing the online_queues prior to attempting to
delete those IO queues, so the driver ended up not requesting the
controller delete any. This patch saves the online_queues prior to
suspending them, and adds that parameter for deleting io queues.
Fixes: c21377f8 ("nvme: Suspend all queues before deletion")
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no reason the nvme controller can ever return all 1's from
reading the CSTS register. This patch returns an error if we observe
that status. Without this, we may incorrectly proceed with controller
initialization and unnecessarilly rely on error handling to clean this.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In order to be completely generic, we have to double check the read
seqlock after acquiring a reference to the fence. If the driver is
allocating fences from a SLAB_DESTROY_BY_RCU, or similar freelist, then
within an RCU grace period a fence may be freed and reallocated. The RCU
read side critical section does not prevent this reallocation, instead
we have to inspect the reservation's seqlock to double check if the
fences have been reassigned as we were acquiring our reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-9-chris@chris-wilson.co.uk
In order to be completely generic, we have to double check the read
seqlock after acquiring a reference to the fence. If the driver is
allocating fences from a SLAB_DESTROY_BY_RCU, or similar freelist, then
within an RCU grace period a fence may be freed and reallocated. The RCU
read side critical section does not prevent this reallocation, instead
we have to inspect the reservation's seqlock to double check if the
fences have been reassigned as we were acquiring our reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-8-chris@chris-wilson.co.uk
In order to be completely generic, we have to double check the read
seqlock after acquiring a reference to the fence. If the driver is
allocating fences from a SLAB_DESTROY_BY_RCU, or similar freelist, then
within an RCU grace period a fence may be freed and reallocated. The RCU
read side critical section does not prevent this reallocation, instead
we have to inspect the reservation's seqlock to double check if the
fences have been reassigned as we were acquiring our reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-7-chris@chris-wilson.co.uk
This variant of fence_get_rcu() takes an RCU protected pointer to a
fence and carefully returns a reference to the fence ensuring that it is
not reallocated as it does. This is required when mixing fences and
SLAB_DESTROY_BY_RCU - although it serves a more pedagogical function atm
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-6-chris@chris-wilson.co.uk
Since fence_wait_timeout_reservation_object_wait_timeout_rcu() with a
timeout of 0 becomes reservation_object_test_signaled_rcu(), we do not
need to handle such conversion in the caller. The only challenge are
those callers that wish to differentiate the error code between the
nonblocking busy check and potentially blocking wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-5-chris@chris-wilson.co.uk
Since fence_wait_timeout_reservation_object_wait_timeout_rcu() with a
timeout of 0 becomes reservation_object_test_signaled_rcu(), we do not
need to handle such conversion in the caller. The only challenge are
those callers that wish to differentiate the error code between the
nonblocking busy check and potentially blocking wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-4-chris@chris-wilson.co.uk
Since fence_wait_timeout_reservation_object_wait_timeout_rcu() with a
timeout of 0 becomes reservation_object_test_signaled_rcu(), we do not
need to handle such conversion in the caller. The only challenge are
those callers that wish to differentiate the error code between the
nonblocking busy check and potentially blocking wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-2-chris@chris-wilson.co.uk
Since fence_wait_timeout_reservation_object_wait_timeout_rcu() with a
timeout of 0 becomes reservation_object_test_signaled_rcu(), we do not
need to handle such conversion in the caller. The only challenge are
those callers that wish to differentiate the error code between the
nonblocking busy check and potentially blocking wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160829070834.22296-1-chris@chris-wilson.co.uk
Current bad block clear implementation assumes the range to clear
overlaps with at least one bad block already stored. If given range to
clear precedes first bad block in a list, the first entry is incorrectly
updated.
Check not only if stored block end is past clear block end but also if
stored block start is before clear block end.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Acked-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently regs_return_value always negates reg[2] if it determines
the syscall has failed, but when called in kernel context this check is
invalid and may result in returning a wrong value.
This fixes errors reported by CONFIG_KPROBES_SANITY_TEST
Fixes: d7e7528bcd ("Audit: push audit success and retcode into arch ptrace.h")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 3.3+
Patchwork: https://patchwork.linux-mips.org/patch/14381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Michael Braun reported that when trying to inject A-MSDUs over
monitor interfaces, the frame doesn't come out right since the
QoS header A-MSDU bit is overwritten.
Rather than adding that bit specifically simply preserve those
bits that we don't set here, since we typically get here with
a zeroed-out QoS header anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Body of an "if" statement wasn't indented. Add a tab.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There might be designs where the power supply circuit is designed
in a way that VDETOFF and SWOFF is required to be set. Otherwise the
RTC detects a power loss. Add a device tree interface for this.
Signed-off-by: Carsten Resch <Carsten.Resch@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
... and Epson RX8900 real time clock
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Our error states are quickly growing, pinning kernel memory with them.
The majority of the space is taken up by the error objects. These
compress well using zlib and without decode are mostly meaningless, so
encoding them does not hinder quickly parsing the error state for
familiarity.
v2: Make the zlib dependency optional
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012090522.367-6-chris@chris-wilson.co.uk
Leave all the pretty printing to userspace and simplify the error
capture to only have a single common object printer. It makes the kernel
code more compact, and the refactoring allows us to apply more complex
transformations like compressing the output.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012090522.367-5-chris@chris-wilson.co.uk
Since the GTT provides universal access to any GPU page, we can use it
to reduce our plethora of read methods to just one. It also has the
important characteristic of being exactly what the GPU sees - if there
are incoherency problems, seeing the batch as executed (rather than as
trapped inside the cpu cache) is important.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012090522.367-4-chris@chris-wilson.co.uk
The error state is purposefully racy as we expect it to be called at any
time and so have avoided any locking whilst capturing the crash dump.
However, with multi-engine GPUs and multiple CPUs, those races can
manifest into OOPSes as we attempt to chase dangling pointers freed on
other CPUs. Under discussion are lots of ways to slow down normal
operation in order to protect the post-mortem error capture, but what it
we take the opposite approach and freeze the machine whilst the error
capture runs (note the GPU may still running, but as long as we don't
process any of the results the driver's bookkeeping will be static).
Note that by of itself, this is not a complete fix. It also depends on
the compiler barriers in list_add/list_del to prevent traversing the
lists into the void. We also depend that we only require state from
carefully controlled sources - i.e. all the state we require for
post-mortem debugging should be reachable from the request itself so
that we only have to worry about retrieving the request carefully. Once
we have the request, we know that all pointers from it are intact.
v2: Avoid drm_clflush_pages() inside stop_machine() as it may use
stop_machine() itself for its wbinvd fallback.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161012090522.367-3-chris@chris-wilson.co.uk
