Reduce indentation, use a variable to save a few pointer dereferences
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
AR_PHY_65NM_CH0_THERM and AR_CH0_THERM were supposed to refer to the
same register, however they had different SREV checks.
Remove the duplicate and use the checks. Since there were other SREV
checks present in the only place that uses this, this will probaby not
affect runtime behavior.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The register layout of AR_PHY_SPECTRAL_SCAN has changed, only AR9280
uses the old layout
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There were two paths in the code for "external" eeprom sources. The code
in eeprom.c only handled the cases where the eeprom data was loaded via
request_firmware. ahb.c and pci.c on the other hand had some duplicate
code which was only used when the eeprom data was passed via
ath9k_platform_data.
With this change all eeprom data handling is now unified in eeprom.c.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We only get nf_connlabels if the user add ct label set expr successfully,
but we will also put nf_connlabels if the user delete ct lable get expr.
This is mismathced, and will cause ct label expr cannot work properly.
Also, if we init something fail, we should put nf_connlabels back.
Otherwise, we may waste to alloc the memory that will never be used.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The purpose for each MOCS entry isn't well defined atm. Defining these
is important to remove any uncertainty about the use of these entries
for example in terms of performance and GPU/CPU coherency.
Suggested by Ville.
v4:
- Rename I915_MOCS_AUTO to I915_MOCS_PTE. (Chris)
CC: Rong R Yang <rong.r.yang@intel.com>
CC: Yakui Zhao <yakui.zhao@intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467383528-16142-1-git-send-email-imre.deak@intel.com
Setting a write-back cache policy in the MOCS entry definition also
implies snooping, which has a considerable overhead. This is
unexpected for a few reasons:
- From user-space's point of view since it didn't want a coherent
surface (it didn't set the buffer as such via the set caching IOCTL).
- There is a separate MOCS entry field for snooping (which we never
set).
- This MOCS table is about caching in (e)LLC and there is no (e)LLC on
BXT. There is a separate table for L3 cache control.
Considering the above the current behavior of snooping looks like an
unintentional side-effect of the WB setting. Changing it to be LLC-UC
gets rid of the snooping without any ill-effects. For a coherent
surface the application would use a separate MOCS entry at index 1 and
call the set caching IOCTL to setup the PTE entries for the
corresponding buffer to be snooped. In the future we could also add a
new MOCS entry for coherent surfaces.
This resulted in 70% improvement in synthetic texturing benchmarks.
Kudos to Valtteri Rantala, Eero Tamminen and Michael T Frederick and
Ville who helped to narrow the source of problem to the kernel and to
the snooping behaviour in particular.
With a follow-up change to adjust the 3rd entry value
igt/gem_mocs_settings is passing after this change.
v2:
- Rebase on v2 of patch 1/2.
v3:
- Set the entry as LLC uncached instead of PTE-passthrough. This way
we also keep snooping disabled, but we also make the cacheability/
coherency setting indepent of the PTE which is managed by the
kernel. (Chris)
CC: Rong R Yang <rong.r.yang@intel.com>
CC: Yakui Zhao <yakui.zhao@intel.com>
CC: Valtteri Rantala <valtteri.rantala@intel.com>
CC: Eero Tamminen <eero.t.tamminen@intel.com>
CC: Michael T Frederick <michael.t.frederick@intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Rong R Yang <rong.r.yang@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467380406-11954-3-git-send-email-imre.deak@intel.com
Use named struct initializers for clarity. Also fix the target cache
definition to reflect its role in GEN9 onwards. On GEN8 a TC value of 0
meant ELLC but on GEN9+ it means the TC and LRU controls are taken from
the PTE.
No functional change, igt/gem_mocs_settings still passing after this
change.
v2: (Chris)
- Add back the hexa literals for the entries.
Add note that igt/gem_mocs_settings still passes.
CC: Rong R Yang <rong.r.yang@intel.com>
CC: Yakui Zhao <yakui.zhao@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467380406-11954-2-git-send-email-imre.deak@intel.com
adfeb3e0 ("cifs: Make echo interval tunable") added a comparison of
vol->echo_interval to server->echo_interval as a criterium to
match_server(), but:
(1) A default value is set for server->echo_interval but not for
vol->echo_interval, meaning these can never match if the echo_interval
option is not specified.
(2) vol->echo_interval is in seconds but server->echo_interval is in
jiffies, meaning these can never match even if the echo_interval option
is specified.
This broke TCP session reuse since match_server() can never return 1.
Fix it.
Fixes: adfeb3e0 ("cifs: Make echo interval tunable")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Since 2006 we have ->i_bdev pinning bdev in question, so there's no
way to get to bdev ->evict_inode() while there's an aliasing inode
anywhere. In other words, the only place walking the list of aliases
is guaranteed to do it only when the list is empty...
Remove the detritus; it should've been done in "[PATCH] Fix a race
condition between ->i_mapping and iput()", but nobody had noticed it
back then.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The current rtc-pcf85063 driver only supports the PCF85063TP device.
Using the existing driver on a PCF85063A will result in the time being
set correctly into the RTC, but the RTC is held in the stopped state.
Therefore, the time will no longer advance and no error is indicated.
The PCF85063A device has a bigger memory map than the PCF85063TP.
The existing driver make use of an address rollover condition,
but the rollover point is different in the two devices.
Signed-off-by: Chris DeBruin <cdeb5783@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The year range is not validated properly
As the driver has been mainlined in 2014, it is not an issue to stop
handling dates between 1970 and 2000 with the benefit of handling dates up
to 2100.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Release call is ignoring the return code from reset call and can
potentially continue even though reset call failed.
If reset_required module parameter is set, this patch is going
to validate the return code and will cause stack dump with
WARN_ON and warn the user of failure.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Open call is ignoring the return code from reset call and can
potentially continue even though reset call failed.
If reset_required module parameter is set, this patch is going
to validate the return code and will abort open if reset fails.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Update and expand the CEC documentation. Especially w.r.t. non-blocking
mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even when the adapter is configured for CEC 1.4, we still check and
use the CEC 2.0 parts of struct cec_log_addrs. Although these aren't
used in CEC messages, the information contained in them is still of
use in the CEC framework itself, so keep this information.
Also zero the unused trailing features[] data and unused logical address
data so the contents isn't random data.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For POLLOUT poll only checked if the adapter was configured, not
if there was room in the transmit queue. Add that check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code was allowing platform devices to be used without a supporting
VFIO reset driver. The hardware can be left in some inconsistent state
after a guest machine abort.
The reset driver will put the hardware back to safe state and disable
interrupts before returning the control back to the host machine.
Adding a new reset_required kernel module option to platform VFIO drivers.
The default value is true for the DT and ACPI based drivers.
The reset requirement value for AMBA drivers is set to false and is
unchangeable to maintain the existing functionality.
New requirements are:
1. A reset function needs to be implemented by the corresponding driver
via DT/ACPI.
2. The reset function needs to be discovered via DT/ACPI.
The probe of the driver will fail if any of the above conditions are
not satisfied.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The device tree code checks for the presence of a reset driver and calls
the of_reset function pointer by looking up the reset driver as a module.
ACPI defines _RST method to perform device level reset. After the _RST
method is executed, the OS can resume using the device. _RST method is
expected to stop DMA transfers and IRQs.
This patch introduces two functions as vfio_platform_acpi_has_reset and
vfio_platform_acpi_call_reset. The has reset method is used to declare
reset capability via the ioctl flag VFIO_DEVICE_FLAGS_RESET. The call
reset function is used to execute the _RST ACPI method.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Getting ready to bring out extra debug information to the caller
so that more verbose information can be printed when an error is
observed.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The code is using the compatible DT string to associate a reset driver
with the actual device itself. The compatible string does not exist on
ACPI based systems. HID is the unique identifier for a device driver
instead.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Creating a new function to determine if this driver supports reset
function or not. This is an attempt to abstract device tree calls
from the rest of the code.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The reset call sequence seems to replicate itself multiple times
across the file. Grouping them together for maintenance reasons.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Renaming the reset function to of_reset as it is only used
by the device tree based platforms.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Just pass the transmitted CEC message to all CEC adapters.
This implements the Monitor All mode for vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main message loop checks if the physical address was valid, and if
not it is assumed that the adapter had been unconfigured.
However, this check is no longer correct, instead it should check
that both adap->is_configured and adap->is_configuring are false.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The size of the transmit queue was unlimited, which meant that
in non-blocking mode you could flood the CEC adapter with messages
to be transmitted.
Limit this to 18 messages.
Also print the number of pending transmits and the timeout value
in the status debugfs file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Ensure that the unused part of the msg array is zeroed. This is
required by CEC 2.0 when receiving shorter messages than expected.
In that case the remaining bytes are assumed to be 0.
There are no such CEC messages yet, but it is required to be future proof.
And since we're doing it for received messages, do it for transmitted
messages as well. It's unambiguous this way.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The filehandle was set to NULL when in non-blocking mode or when
no reply is needed.
This is wrong: the filehandle is needed in non-blocking mode to ensure
that the result of the transmit can be obtained through CEC_RECEIVE.
And the 'reply' check was also incorrect since it should have checked the
timeout field (the reply can be 0). In any case, when in blocking mode
there is no need to set the fh to NULL either.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Before transmitting a message clear all status fields and always fill
in the sequence number. Make sure the sequence number is never 0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CEC_RECEIVE returns a message the original timeout field
was overwritten. Restore the timeout field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set .tm_sec to 0 instead of -1 to signal minute accuracy.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since all time members of the alarm data is initialized to -1 the drivers
are responsible to set the tm_sec member to 0.
Fixes: d68778b80d ("rtc: initialize output parameter for read alarm to "uninitialized"")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Stepping with PSTATE.D=1 is bad news. The step won't generate a debug
exception and we'll likely walk off into random data structures. This
should never happen, but when it does, it's a PITA to debug. Add a
WARN_ON to shout if we realise this is about to take place.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The debug enable/disable macros are not used anywhere in the kernel, so
remove them from irqflags.h
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is no need to explicitly clear the SS bit immediately before
setting it unconditionally.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As per code flow s3c_rtc_setfreq() will get called with rtc clock disabled
and in set_freq we perform h/w registers read/write, which results in a
kernel crash on exynos7 platform while probing rtc driver.
Below is code flow:
s3c_rtc_probe()
clk_prepare_enable(info->rtc_clk) // rtc clock enabled
s3c_rtc_gettime() // will enable clk if not done, and disable it upon exit
s3c_rtc_setfreq() //then this will be called with clk disabled
This patch take cares of such issue by adding s3c_rtc_{enable/disable}_clk in
s3c_rtc_setfreq().
Fixes: 24e1455493 ("drivers/rtc/rtc-s3c.c: delete duplicate clock control")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the end of s3c_rtc_probe(), s3c_rtc_disable_clk() being called with rtc
clock already disabled (by s3c_rtc_gettime()), which looks extra and
unnecessary call. Lets clean it up.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Sphinx is really evil when an older version finds an extra
attribute for the :toctree: tag: it simply ignores everything
and produce documents without any chapter inside!
As we're now using tags available only on Sphinx 1.4.x, we
need to use some creative ways to add a title before the
table of contents. Do that by using a css class.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If devm_add_action() fails we are explicitly calling the cleanup to free
the resources allocated. Lets use the helper devm_add_action_or_reset()
and return directly in case of error, as we know that the cleanup function
has been already called by the helper if there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If devm_add_action() fails we are explicitly calling the cleanup to free
the resources allocated. Lets use the helper devm_add_action_or_reset()
and return directly in case of error, as we know that the cleanup function
has been already called by the helper if there was any error.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The command flow is exactly the same, the core simply needs to be
told to enable TPM2 mode when the compatible string indicates a
TPM2.
Signed-off-by: Andrew Azmansky <andrew.zamansky@nuvoton.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.
tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.
For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
