Add function rs_setup_recovery() to allow for defined setup of RAID set
recovery in the constructor.
Will be called with dev_sectors={0, rdev->sectors, MaxSectors} to
recover a new or enforced sync, grown or not to be synhronized RAID set
respectively.
Prevents recovery on raid0, which doesn't support it.
Enforces recovery on raid6 to ensure properly defined Syndromes
mandatory for that MD personality are being created.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.
This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 3647234101 (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 3647234101 ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This was succesfully tested with 4366B1. A small workaround is needed
for the main interface otherwise it would stuck at the hidden state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building with separate object directories and driver specific
Makefiles that add additional header include paths, Kbuild adjusts
the gcc flags so that we include both the directory in the source
tree and in the object tree.
However, due to another bug I fixed earlier, this did not actually
include the correct directory in the object tree, so we know that
we only really need the source tree here. Also, including the
object tree sometimes causes warnings about nonexisting directories
when the include path only exists in the source.
This changes the logic to only emit the -I argument for the srctree,
not for objects. We still need both $(srctree)/$(src) and $(obj)
though, so I'm adding them manually.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
There are very few files that need add an -I$(obj) gcc for the preprocessor
or the assembler. For C files, we add always these for both the objtree and
srctree, but for the other ones we require the Makefile to add them, and
Kbuild then adds it for both trees.
As a preparation for changing the meaning of the -I$(obj) directive to
only refer to the srctree, this changes the two instances in arch/x86 to use
an explictit $(objtree) prefix where needed, otherwise we won't find the
headers any more, as reported by the kbuild 0day builder.
arch/x86/realmode/rm/realmode.lds.S:75:20: fatal error: pasyms.h: No such file or directory
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
When $(LINUXINCLUDE) is added to the cflags of a target that
normall doesn't have it (e.g. HOSTCFLAGS), each entry in the
list is expanded so that we search both $(objtree) and $(srctree),
which is a bit silly, as we already know which of the two we
want for each entry in LINUXINCLUDE.
Also, a follow-up patch changes the behavior so we only look in
$(srctree) for manually added include path, and that breaks finding
the generated headers.
This adds an explicit $(objtree) for each tree that we want to
look for generated files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
arch/$(hdr-arch)/include/generated/uapi is included twice in the
header search path, which is unnecessary, so this changes the
top-level Makefile to drop the second instance by filtering out
everything from USERINCLUDE that was already part of LINUXINCLUDE.
This should have very little effect other than making the 'make V=1'
output slightly smaller and making the build time faster by a miniscule
amount, but it seems to be cleaner.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
When we build with O=objdir and objdir is directly below the source tree,
$(srctree) becomes '..'.
When a Makefile adds a CFLAGS option like -Ipath/to/headers and
we are building with a separate object directory, Kbuild tries to
add two -I options, one for the source tree and one for the object
tree. An absolute path is treated as a special case, and don't add
this one twice. This also normally catches -I$(srctree)/$(src)
as $(srctree) usually is an absolute directory like /home/arnd/linux/.
The combination of the two behaviors however results in an invalid
path name to be included: we get both ../$(src) and ../../$(src),
the latter one pointing outside of the source tree, usually to a
nonexisting directory. Building with 'make W=1' makes this obvious:
cc1: error: ../../arch/arm/mach-s3c24xx/include: No such file or directory [-Werror=missing-include-dirs]
This adds another special case, treating path names starting with ../
like those starting with / so we don't try to prefix that with
$(srctree).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Marek <mmarek@suse.com>
We support the SMBus Host Notify protocol now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The parameter description is from a previous implementation, update
it to describe the actual implementation.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
loop_until_timeout() replaced a do {} while loop in the at24 driver
with a for loop which, under certain circumstances (such as heavy load
or low value of the write_timeout argument), can lead to the code in
the loop never being executed.
Make sure that at least one iteration of the code enclosed within
loop_until_timeout() is always executed.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The titles at the media books were misleading, and some books
were not numbered.
Rename the kAPI book to better reflect its contents, be more
consistent on the initial rst file for each book and better
name them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I ended by adding twice each media header, because I saw some
missing stuff at the documents. It seems it was my mistake,
as everything seems to be there.
So, remove those extra stuff, to avoid duplicating the
documentation of the functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the contents of this file to bttv.rst and saa7134.rst.
With that, we can finally remove Documentation/video4linux.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Import the contents of hauppauge-wintv-cx88-ir.txt, after
converted to ReST into cx88.rst file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If we care to move all the checks that do not involve any memory
allocation, we can simplify the MAPI error handling. Let's do that,
it cannot hurt.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
vgic_its_cmd_handle_mapi has an extra "subcmd" argument, which is
already contained in the command buffer that all command handlers
obtain from the command queue. Let's drop it, as it is not that
useful.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is no need to have separate functions to validate devices
and collections, as the architecture doesn't really distinguish the
two, and they are supposed to be managed the same way.
Let's turn the DevID checker into a generic one.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Going from the ITS structure to the corresponding KVM structure
would be quite handy at times. The kvm_device pointer that is
passed at create time is quite convenient for this, so let's
keep a copy of it in the vgic_its structure.
This will be put to a good use in subsequent patches.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of spreading random allocations all over the place,
consolidate allocation/init/freeing of collections in a pair
of constructor/destructor.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When checking that the storage address of a device entry is valid,
it is critical to compute the actual address of the entry, rather
than relying on the beginning of the page to match a CPU page of
the same size: for example, if the guest places the table at the
last 64kB boundary of RAM, but RAM size isn't a multiple of 64kB...
Fix this by computing the actual offset of the device ID in the
L2 page, and check the corresponding GFN.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Checking that the device_id fits if the table, and we must make
sure that the associated memory is also accessible.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The nr_entries variable in vgic_its_check_device_id actually
describe the size of the L1 table, and not the number of
entries in this table.
Rename it to l1_tbl_size, so that we can now change the code
with a better understanding of what is what.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ITS tables are stored in LE format. If the host is reading
a L1 table entry to check its validity, it must convert it to
the CPU endianness.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The current code will fail on valid indirect tables, and happily
use the ones that are pointing out of the guest RAM. Funny what a
small "!" can do for you...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of sprinkling raw kref_get() calls everytime we cannot
do a normal vgic_get_irq(), use the existing vgic_get_irq_kref(),
which does the same thing and is paired with a vgic_put_irq().
vgic_get_irq_kref is moved to vgic.h in order to be easily shared.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Let's restore some of the #defines that have been savagely dropped
by the introduction of the KVM ITS code, as pointlessly break
other users (including series that are already in -next).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
For VGICv2 save and restore the CPU interface registers
are accessed. Restore the modality which has been altered.
Also explicitly set the iodev_type for both the DIST and CPU
interface.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that all ITS emulation functionality is in place, we advertise
MSI functionality to userland and also the ITS device to the guest - if
userland has configured that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When userland wants to inject an MSI into the guest, it uses the
KVM_SIGNAL_MSI ioctl, which carries the doorbell address along with
the payload and the device ID.
With the help of the KVM IO bus framework we learn the corresponding
ITS from the doorbell address. We then use our wrapper functions to
iterate the linked lists and find the proper Interrupt Translation Table
Entry (ITTE) and thus the corresponding struct vgic_irq to finally set
the pending bit.
We also provide the handler for the ITS "INT" command, which allows a
guest to trigger an MSI via the ITS command queue. Since this one knows
about the right ITS already, we directly call the MMIO handler function
without using the kvm_io_bus framework.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The connection between a device, an event ID, the LPI number and the
associated CPU is stored in in-memory tables in a GICv3, but their
format is not specified by the spec. Instead software uses a command
queue in a ring buffer to let an ITS implementation use its own
format.
Implement handlers for the various ITS commands and let them store
the requested relation into our own data structures. Those data
structures are protected by the its_lock mutex.
Our internal ring buffer read and write pointers are protected by the
its_cmd mutex, so that only one VCPU per ITS can handle commands at
any given time.
Error handling is very basic at the moment, as we don't have a good
way of communicating errors to the guest (usually an SError).
The INT command handler is missing from this patch, as we gain the
capability of actually injecting MSIs into the guest only later on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The (system-wide) LPI configuration table is held in a table in
(guest) memory. To achieve reasonable performance, we cache this data
in our struct vgic_irq. If the guest updates the configuration data
(which consists of the enable bit and the priority value), it issues
an INV or INVALL command to allow us to update our information.
Provide functions that update that information for one LPI or all LPIs
mapped to a specific collection.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The LPI pending status for a GICv3 redistributor is held in a table
in (guest) memory. To achieve reasonable performance, we cache the
pending bit in our struct vgic_irq. The initial pending state must be
read from guest memory upon enabling LPIs for this redistributor.
As we can't access the guest memory while we hold the lpi_list spinlock,
we create a snapshot of the LPI list and iterate over that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
LPIs are dynamically created (mapped) at guest runtime and their
actual number can be quite high, but is mostly assigned using a very
sparse allocation scheme. So arrays are not an ideal data structure
to hold the information.
We use a spin-lock protected linked list to hold all mapped LPIs,
represented by their struct vgic_irq. This lock is grouped between the
ap_list_lock and the vgic_irq lock in our locking order.
Also we store a pointer to that struct vgic_irq in our struct its_itte,
so we can easily access it.
Eventually we call our new vgic_get_lpi() from vgic_get_irq(), so
the VGIC code gets transparently access to LPIs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
