The ethernet core has 3 IRQs. Using the IRQ grouping registers we are able
to separate TX and RX IRQs, which allows us to service them on separate
cores. This patch splits the IRQ handler into 2 separate functions, one for
TX and another for RX. The TX housekeeping is split out into its own NAPI
handler.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that enables and disables IRQs is missing proper locking. After
adding the IRQ grouping patch and routing the RX and TX IRQs to different
cores we experienced IRQ stalls. Fix this by adding proper locking.
We use a dedicated lock to reduce the latency if the IRQ code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently uses variables to store and never modify the bit masks
of interrupts. This is legacy code from an early version of the driver
that supported MIPS based SoCs where the IRQ bits depended on the actual
SoC. As the bits are the same for all ARM based SoCs using this driver we
can remove the intermediate variables.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was originally written for MIPS based SoC. These required the
IRQ mask register to be read after writing it to ensure that the content
was actually applied. As this version only works on ARM based SoCs, we can
safely remove the 2 reads as they are no longer required.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.
This is already implemented in iproute2:
if (cmd == RTM_NEWRULE) {
req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
req.r.rtm_type = RTN_UNICAST;
}
Tested ipv4 and ipv6 with net-next linux on qemu x86
expected behavior after patch:
localhost ~ # ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0: from all lookup local
1005: from 10.46.177.97 lookup 104
32766: from all lookup main
32767: from all lookup default
There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomain
Signed-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to use strlen, etc to figure that out, just use the return from
printf(), it will tell how wide the following line needs to be.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20160630082955.GA30921@twins.programming.kicks-ass.net
[ split from a larger patch ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In previous commit 01f83d6984
the following comments were added:
"When peer uses tiny windows, there is no use in packetizing to sub-MSS
pieces for the sake of SWS or making sure there are enough packets in
the pipe for fast recovery."
The test should be > TCP_MSS_DEFAULT not >= 512. This allows low end
devices that send an MSS of 536 (TCP_MSS_DEFAULT) to see better network
performance by sending it 536 bytes of data at a time instead of bounding
to half window size (268). Other network stacks work this way, e.g. HP-UX.
Signed-off-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found that sometimes a restored tcp socket doesn't work.
A reason of this bug is incorrect window parameters and in this case
tcp_acceptable_seq() returns tcp_wnd_end(tp) instead of tp->snd_nxt. The
other side drops packets with this seq, because seq is less than
tp->rcv_nxt ( tcp_sequence() ).
Data from a send queue is sent only if there is enough space in a
window, so when we restore unacked data, we need to expand a window to
fit this data.
This was in a first version of this patch:
"tcp: extend window to fit all restored unacked data in a send queue"
Then Alexey recommended me to restore window parameters instead of
adjusted them according with data in a sent queue. This sounds resonable.
rcv_wnd has to be restored, because it was reported to another side
and the offered window is never shrunk.
One of reasons why we need to restore snd_wnd was described above.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCIe host controller found on Tegra20 has a hardware bug that causes
PCIe interrupts to get lost when LP2 is enabled. Stub out the workaround
on 64-bit ARM because none of the more recent Tegra SoC generations seem
to have this bug anymore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds the Device Tree description for the two XOR engines
found in the CP part of the Armada 7K/8K SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As suggested by Rob Herring, we should:
1/ Use a SoC-specific compatible string in addition to the more generic
one.
2/ The generic compatible string has been changed from
"marvell,mv-xor-v2" to "marvell,xor-v2".
We simply reflect the changes made to the Device Tree bindings to the
relevant Marvell 7K/8K Device Tree files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A cleanup to include the headers correctly caused another build problem:
arch/arm/mach-mvebu/kirkwood-pm.c:70:13: error: redefinition of 'kirkwood_pm_init'
arch/arm/mach-mvebu/kirkwood-pm.h:23:20: note: previous definition of 'kirkwood_pm_init' was here
The underlying issue is that kirkwood-pm.o is not actually meant to be
used when CONFIG_PM is disabled, so we should also leave it out of the
Makefile.
The same seems to be true for the PM code in MACH_MVEBU_V7, and I'm
treating it the same way here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d705c1a66e ("ARM: Kirkwood: fix kirkwood_pm_init() declaration/type")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Tegra XHCI driver does not currently manage the Tegra XUSB power
partitions and so it these partitions have not been enabled by the
bootloader then the system will crash when probing the XHCI device.
While proper support for managing the power partitions is being
developed to the XHCI driver for Tegra, for now power on all the XUSB
partitions for USB host and super-speed on boot if the XHCI driver is
enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If CONFIG_PM_GENERIC_DOMAINS is not enabled, then power partitions
associated with a device will not be enabled automatically by the PM
core when the device is in use. To avoid situations where a device in
a power partition is to be used but the partition is not enabled,
initialise the power partitions for Tegra early in the boot process and
if CONFIG_PM_GENERIC_DOMAINS is not enabled, then power on all
partitions defined in the device-tree blob.
Note that if CONFIG_PM_GENERIC_DOMAINS is not enabled, after the
partitions are turned on, the clocks and resets used as part of the
sequence for turning on the partition are released again as they are no
longer needed by the PMC driver. Another benefit of this is that this
avoids any issues of sharing resets between the PMC driver and other
device drivers that may wish to independently control a particular
reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Utility function to fetch arch using evsel. (evsel->env->arch)
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anton Blanchard <anton@ozlabs.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1467267262-4589-2-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When initialising a powergate, only a single error message is shown if
the initialisation fails. Add more error messages to give specific
details of what failed if the initialisation failed and remove the
generic failure message.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
While sending the blocking directIO in fuse, the write request is broken
into sub-requests, each of default size 128k and all the requests are sent
in non-blocking background mode if async_dio mode is supported by libfuse.
The process which issue the write wait for the completion of all the
sub-requests. Sending multiple requests parallely gives a chance to perform
parallel writes in the user space fuse implementation if it is
multi-threaded and hence improves the performance.
When there is a size extending aio dio write, we switch to blocking mode so
that we can properly update the size of the file after completion of the
writes. However, in this situation all the sub-requests are sent in
serialized manner where the next request is sent only after receiving the
reply of the current request. Hence the multi-threaded user space
implementation is not utilized properly.
This patch changes the size extending aio dio behavior to exactly follow
blocking dio. For multi threaded fuse implementation having 10 threads and
using buffer size of 64MB to perform async directIO, we are getting double
the speed.
Signed-off-by: Ashish Sangwan <ashishsangwan2@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Negotiate with userspace filesystems whether they support parallel readdir
and lookup. Disable parallelism by default for fear of breaking fuse
filesystems.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 9902af79c0 ("parallel lookups: actual switch to rwsem")
Fixes: d9b3dbdcfd ("fuse: switch to ->iterate_shared()")
Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On Tegra124, Tegra132 and Tegra210 devices the pads used by the Display
Port Auxiliary (DPAUX) channel are multiplexed such that they can also
be used by one of the internal I2C controllers. Note that this is
different from I2C-over-AUX supported by the DPAUX controller. The
register that configures these pads is part of the DPAUX controllers
register set and so a pinctrl driver is being added for the DPAUX device
to share these pads. Add the device-tree binding documentation for the
DPAUX pad controller.
Although there is only one group of pads associated with the DPAUX that
can be multiplexed, the group still needs to be described by the binding.
If the 'groups' property is not present in the binding, then the pads
will not be allocated by the pinctrl core for a client and this would
allow another client to re-configure the same pads that may already be
in-use.
Please note that although the "off" function for the DPAUX pads is not
technically a pin-mux setting but more of a pin-conf setting it is
simpler to expose these as a function so that the user can simply select
either "aux", "i2c" or "off" as the current function/mode.
Update the main DPAUX binding documentation to reference the DPAUX pad
controller binding document and add the 'i2c-bus' subnode. The 'i2c-bus'
subnode is used for populating I2C slaves for the DPAUX device so that
the I2C driver core does not attempt to add the DPAUX pad controller
nodes as I2C slaves.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
To utilise the DPAUX on Tegra, the SOR power partition must be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework for DPAUX. However, the sequence
for gating/ungating the SOR power partition requires that the DPAUX
reset is asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the
DPAUX driver cannot request the same reset unless we mark the resets as
shared. Sharing resets will not work in this case because we cannot
guarantee that the reset will be asserted/de-asserted at the appropriate
time. Therefore, given that the Tegra generic PM domain code will handle
the DPAUX reset, do not request the reset in the DPAUX driver if the
DPAUX device has a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the DPAUX compatibility string information for Tegra124, Tegra132
and Tegra210.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for adding pinctrl support for the DPAUX pads, add a
couple of helpers functions to configure the pads and control their
power.
Please note that although a simple if-statement could be used instead
of a case statement for configuring the pads as there are only two
possible modes, a case statement is used because when integrating with
the pinctrl framework, we need to be able to handle invalid modes that
could be passed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the probing of the DPAUX fails, then clocks are left enabled and the
DPAUX reset de-asserted. Add code to perform the necessary clean-up on
probe failure by disabling clocks and asserting the reset.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the missing unlock before return from function i915_ppgtt_info()
in the error handling case.
Fixes: 1d2ac403ae3b(drm: Protect dev->filelist with its own mutex)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465861320-26221-1-git-send-email-weiyj_lk@163.com
(cherry picked from commit b021248690)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 0259f522e0 ('soc/tegra: pmc: Restore base address on probe
failure') fixes an issue where the PMC base address pointer is not
restored on probe failure. However, this fix creates another problem
where if early initialisation of the PMC driver fails and an initial
mapping for the PMC address space is not created, then when the PMC
device is probed, the PMC base address pointer will not be valid and
this will cause a crash when tegra_pmc_init() is called and attempts
to access a register.
Although the PMC address space is mapped a 2nd time during the probe
and so this could be fixed by populating the base address pointer
earlier during the probe, this adds more complexity to the code.
Moreover, the PMC probe also assumes the the soc data pointer is also
initialised when the device is probed and if not will also lead to a
crash when calling tegra_pmc_init_tsense_reset(). Given that if the
early initialisation does fail then something bad has happen, it seems
acceptable to allow the PMC device probe to fail as well. Therefore, if
the PMC base address pointer or soc data pointer are not valid when
probing the PMC device, WARN and return an error.
Fixes: 0259f522e0 ('soc/tegra: pmc: Restore base address on probe failure')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing of_node_put() in PMC early initialisation function to avoid
leaking the device nodes.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
[treding@nvidia.com: squash in a couple more of_node_put() calls]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The mutex used by the PMC driver may not be initialised if early
initialisation of the driver fails. If this does happen, then it could
be possible for callers of the public PMC functions to still attempt to
acquire the mutex. Fix this by initialising the mutex as soon as
possible to ensure it will always be initialised.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The public functions exported by the PMC driver use the presence of the
SoC data pointer to determine if the PMC device is configured and the
registers can be accessed. However, the SoC data is populated before the
PMC register space is mapped and this opens a window where the SoC data
pointer is valid but the register space has not yet been mapped which
could lead to a crash. Furthermore, if the mapping of the PMC register
space fails, then the SoC data pointer is not cleared and so would
expose a larger window where a crash could occur.
Fix this by initialising the SoC data pointer after the PMC register
space has been mapped.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nikolay Aleksandrov says:
====================
net: bridge: add support for IGMP/MLD stats
This patchset adds support for the new IFLA_STATS_LINK_XSTATS_SLAVE
attribute which can be used with RTM_GETSTATS in order to export per-slave
statistics. It works by passing the attribute to the linkxstats callback
and if the callback user supports it - it should dump that slave's stats.
This is much more scalable and permits us to request only a single port's
statistics instead of dumping everything every time.
The second patch adds support for per-port IGMP/MLD statistics and uses
the new API to export them for the bridge and its ports. The stats are
made in a very lightweight manner, the normal fast-path is not affected
at all and the flood paths (br_flood/br_multicast_flood) are only affected
if the packet is IGMP and the IGMP stats have been enabled using cache-hot
data for the check.
v2: Patch 01 is new, patch 02 has been reworked to use the new API, also
in addition counters for IGMP/MLD parse errors have been added and members
are added for per-port multicast traffic stats. The multicast counting has
been slightly optimized (moved the br_multicast_count inside the IPv4/6
IGMP functions after the checks for IGMP traffic) to avoid one conditional
that was on all of the multicast traffic path (both IGMP and other).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports
* MLD Queries
* MLD Leaves
* MLD v1/v2 reports
These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ee042aa40b.
Something appears to be off in the timing, but as far as I can tell it
is not along the event delivery path. The net effect appears to be
rendering flicker (the current render buffer appears on the scanout,
with what appears to be active rendering for a fraction of a frame) and
is causing me a headache.
The cursor is also being stalled by page flips, causing a "heavy mouse"
and jitter.
Daniel Stone did find what appears to the cause of the tearing, in
https://lists.freedesktop.org/archives/intel-gfx/2016-June/099466.html
That is the parameter passed to intel_atomic_commit_tail is the
old_state but we need the new_state to wait upon.
That leaves the question of how the CRC based tests didn't spot the
error (how can we improve our tests?), the issue of legacy cursor
stalling flips, and the issue of flips stalling the cursor. For the
moment, step back until the condundrum of new/old state is reviewed
along with more tests!
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Reported-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96593
Testcase: igt/kms_cursor_legacy/basic-cursor-vs-flip
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466772243-21879-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Previously, the action frames to group address was not encrypted. But
[1] "Table 8-38 Category values" indicates "Mesh" and "Multihop" category
action frames should be encrypted (Group addressed privacy == yes). And the
encyption key should be MGTK ([1] 10.13 Group addressed robust management frame
procedures). So this patch modifies the code to make it suitable for spec.
[1] IEEE Std 802.11-2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
We normally return an uninitialized value, but no one checks it so it
doesn't matter. Anyway, let's silence the static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
When building a kernel with W=1, the nl80211.c file causes a number of
warnings, all about the same problem:
net/wireless/nl80211.c: In function 'nl80211_parse_mesh_config':
net/wireless/nl80211.c:5287:103: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5290:96: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5293:124: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5295:148: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5298:106: error: comparison is always false due to limited range of data type [-Werror=type-limits]
net/wireless/nl80211.c:5305:116: error: comparison is always false due to limited range of data type [-Werror=type-limits]
The problem is that gcc does not notice that the check is generate
by a macro, so it complains about comparing an unsigned type against 0.
I've tried to come up with a way to rephrase that code in a way that
avoids the warnings and otherwise improves the code as well.
This uses a set of new helper functions that perform the range checking,
and should provide slightly better type safety than the older patch,
at the expense of adding 44 lines to the code. Binary code size is
basically unchanged though (20 bytes added to 126561 bytes .text).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Registering wmediumd is currently limited to the initial network
namespace. This patch enables wmediumd to attach from non-initial
network namespaces using a user namespace having CAP_NET_ADMIN. A
registered wmediumd can forward frames on radios that have been created
in the same network namespace, even if they have been moved to other
network namespaces.
The wmediumd Netlink portid is tracked per net namespace. Additionally,
the portid is stored on all radios created in that net namespace to
simplify the portid lookup in the data path.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
