Use "ti,cpsw-mdio" to enable PM runtime auto-suspend on supported
platforms, where MDIO is implemented as part of TI CPSW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "ti,cpsw-mdio" compatible string for Davinci MDIO, because
it's required to distinguish the case when MDIO is part of TI CPSW to
enable features supported by TI CPSW (for example, enable PM
management).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document missed "ti,am4372-mdio" compat string used for TI am437x SoC
(am4372.dtsi).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davinci MDIO is always used as slave device which services
read/write requests from MDIO/PHY core. It doesn't use IRQ also.
As result, It's possible to relax PM runtime constraints for Davinci
MDIO and enable it on demand, instead of powering it during probe
and powering off during removal.
Hence, implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of
TI devices and not all of them expected to work corectly with RPM
autosuspend enabled:
- expected to work on SoCs where MDIO is part of TI CPSW
(cpsw.c DRA7/am57x, am437x, am335x, dm814x)
- not verified on Keystone 2 and other SoCs where MDIO is used with TI EMAC IP
(davinci_emac.c: dm6467-emac, am3517-emac, dm816-emac).
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PM runtime .runtime_suspend()/.runtime_resume() callbacks and
perform Davinci MDIO enabling/disabling from these callbacks. This
allows to reuse pm_runtime_force_suspend/resume() APIs during System
suspend and required for further implementation of PM runtime
autosuspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO MDIO_CONTROL.CLKDIV can be calculated only once
during probe, hence split __davinci_mdio_reset() on
davinci_mdio_init_clk() and davinci_mdio_enable(). Initialize and
save CLKDIV in .probe(). Then just use saved value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not expected Davinci MDIO to be accessible after its suspend
callbacks have been called:
- all consumers of Davinci MDIO will stop/disconnect phys at Device
suspend stage;
- all phys are expected to be suspned already by PHY/MDIO core;
- MDIO locking is done by MDIO Bus code.
Hence, it's safe to drop "suspended" and "lock" fields from mdio_data.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is disabled when Davinci MDIO .suspend_late() and
.resume_early() callbacks are called. As result, any PM runtime calls here will
be just a nop and can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do PM runtime initialization later in probe - this allows to simplify
error handling a bit.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This public header contains static inlines to pack and unpack CEC
messages. It is for use in both the kernel and in userspace.
Since the CEC framework will initially be in staging this header is
not yet in include/uapi. Once the framework is moved out of staging
this header should be moved to uapi at the same time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This header contains the CEC public API. Since the CEC framework will
initially be part of staging this header is kept out of include/uapi for
the time being until the CEC framework will be moved out of staging.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Giuseppe Cavallaro says:
====================
stmmac: rework and enhance the PCS support
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers;
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So these patches aim to reorganize and enhance the PCS support;
to do that, some small inline functions have been provided and
also some rework to the PCS ISR part has been done.
In the end, the SGMII for MAC2MAC connection has been introduced.
All patches have been built on top of net-next git and, as for
the previous version, not fully tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, all gmac cores disable the PCS block and always
enable the PMT.
Note that this is done in a different way by 3.x and 4.x cores.
With this rework, PCS and PMT interrupt masks can be driven by
parameters now moved inside the mac_device_info structure
and the settings follow what the HW capability register reports.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers:
for example:
AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
AN_Expansion, TBI_Extended_Status.
Just the RGMII/SMII Control/Status register differs.
So This patch aims to reorganize and enhance the PCS support.
It removes the existent support from the dwmac1000/dwmac4_core.c
moving basic PCS functions inside a new file called: stmmac_pcs.h.
The patch also reviews the available APIs to be better shared among
different hardware and easily enhanced to support new features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cec-edid module contains helper functions to find and manipulate
the CEC physical address inside an EDID. Even if the CEC support itself
is disabled, drivers will still need these functions. Which is the
reason this is module is separate from the upcoming CEC framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make kvm_guest_{enter,exit} and __kvm_guest_{enter,exit} trivial wrappers
around the code in context_tracking.h. Name the context_tracking.h functions
consistently with what those for kernel<->user switch.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix rcar_vin_try_fmt's use of an inappropriate pad number when calling
the subdev set_fmt function - for the ADV7612, IDs should be non-zero.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add detection of source pad number for drivers aware of the media controller
API, so that rcar-vin can create device nodes to support modern drivers such
as adv7604.c (for HDMI on Lager) and the converted adv7180.c (for composite)
underneath.
Building rcar_vin gains a dependency on CONFIG_MEDIA_CONTROLLER, in
line with requirements for building the drivers associated with it.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[ulrich.hecht+renesas@gmail.com: adapted to rcar-vin rewrite]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage Confidence is mandary to Windows Precision Touchpad devices. If
it is examined in input_mapping on a WIndows Precision Touchpad, a new add
quirk MT_QUIRK_CONFIDENCE desgned for such devices will be applied to the
device. A touch with the confidence bit is not set is determined as
invalid.
Tested on Dell XPS13 9343
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 25a84db15b ("HID: multitouch: enable palm rejection
if device implements confidence usage")
The commit enables palm rejection for Win8 Precision Touchpad devices but
the quirk MT_QUIRK_VALID_IS_CONFIDENCE it is using is not working very
properly. This quirk is originally designed for some WIn7 touchscreens. Use
of this for a Win8 Precision Touchpad will cause unexpected pointer jumping
problem.
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andy Lutomirski <luto@kernel.org> # XPS 13 9350, BIOS 1.4.3
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The bits single_step and instruction_fetch lost their meaning
with git commit 5e9a26928f "[S390] ptrace cleanup".
Clarify the comment for these two bits.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The comments for the unlocked v4l2_ctrl_s_ctrl* functions were wrong (copy
and pasted from the locked variants). Fix this, since it is confusing.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Memory allocated for maxiradio device is not deallocated when
the device is removed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If *nplanes is not zero, it should use the requested size if valid
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver fails to reset the camera or to set up control handlers, it
has to power the camera back off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_subdev_internal_ops structure is never modified. All other
v4l2_subdev_internal_ops structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value is not used after the assignment.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Users won't know what to put in this module option if it isn't
described.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Audio hw params are shared across all DMA channels,
so if the user changes any of these while any DMA channel is
enabled, it will impact the enabled channels, potentially causing
serious instability issues.
This commit avoids such situation, by preventing any hw param
change (on any DMA channel) if any other DMA audio channel is capturing.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, the driver has a fixed period size of 4096 bytes
(2048 frames). Since this hardware can configure the audio
capture size, this commit allows a period size range of [512-4096].
This is very useful to reduce the audio latency.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we've introduced the dma_mode parameter to pick the
DMA operation, let's use it to also select the audio DMA
operation.
When dma_mode != memcpy, the driver will avoid using memcpy
in the audio capture path, and the DMA hardware operation
will act directly on the ALSA buffers.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the driver has the infrastructure to support more
DMA modes, let's add the DMA scatter-gather mode.
In this mode, the device delivers sequential top-bottom
frames. The scatter-gather logic is based on staging's
tw686x-kh driver (by Krzysztof Ha?asa).
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the driver has the infrastructure to support more
DMA modes, let's add the DMA contiguous interlaced frame mode.
In this mode, the DMA P and B buffers are programmed with
the user-provided buffers. When a P (or B) frame is ready,
a new buffer is dequeued into P (or B).
In addition to interlaced fields, the device can also be
programmed to deliver alternate fields. Only interlaced
mode is supported for now.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When calling eeh_rmv_device() in eeh_reset_device() for partial hotplug
case, @rmv_data instead of its address is the proper argument.
Otherwise, the stack frame is corrupted when writing to
@rmv_data (actually its address) in eeh_rmv_device(). It results in
kernel crash as observed.
This fixes the issue by passing @rmv_data, not its address to
eeh_rmv_device() in eeh_reset_device().
Fixes: 67086e32b5 ("powerpc/eeh: powerpc/eeh: Support error recovery for VF PE")
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Let's set the corner stone to support all the DMA modes
available on this device.
For stability reasons, the driver is currently setting DMA frame
mode, and using single DMA buffers to get the P and B buffers.
Each frame is then memcpy'ed into the user buffer.
However, other platforms might be interested in avoiding this
memcpy, or in taking advantage of the chip's DMA scatter-gather
capabilities.
To achieve this, this commit introduces a "dma_mode" module parameter,
and a tw686x_dma_ops struct. This will allow to define functions to
alloc/free DMA buffers, and to return the frames to userspace.
The memcpy-based method described above is named as dma_mode="memcpy".
Current alloc/free functions are renamed as tw686x_memcpy_xxx,
and are now used through a memcpy_dma_ops.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
