The exynos low-level debug macros need to be fixed if the system is being
built big endian. Add the necessary endian swaps for accessing the registers
to get output working again
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add i2c_hid_shutdown for i2c-hid driver to send suspend cmd & free
irq before device shutdown.
Some HW design (i.e. Umaro, a chromebook model) is that the power to
i2c hid device won't down after device shutdown. Also the i2c-hid driver
do not send suspend cmd to the hid i2c device and free its irq before
shutdown.So if We touch the touchscreen or some other i2c hid device,
the power consumtion will be go up even when the device is in shutdown
state.
Though the root cause maybe a HW issue. But it seems that it is a
good pratice to set power sleep for i2c-hid device before shutdown.
Signed-off-by: Guohua Zhong <ghzhong@yifangdigital.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The access right of kernel param "i915.enable_gvt" should be read-only as
it only applies during module load (and is not *runtime* writable).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466425022-3709-1-git-send-email-zhi.a.wang@intel.com
If the GPU load is low enough, it's possible that we'll be stuck at idle
frequency rather than transition into softmin frequency requested by
userspace.
v2: Use intel_set_rps, drop vlv_set_idle
v3: Back to vlv_set_idle, clamp to valid range
v4: Place intel_set_rps at the end
References: https://bugs.freedesktop.org/show_bug.cgi?id=89728
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1466416707-12075-1-git-send-email-michal.winiarski@intel.com
The ONLY places that guc_id (aka hw_id) should be used are those where
the value or address is determined by and shared with the GuC firmware;
specifically, when filling in the GuC-context-descriptor or the GuC
addon data, or putting an entry in the GuC's work queue.
It need not (and therefore should not) be used to index GuC statistics
or similar host-managed tracking data. In particular, i915_guc_submit()
produces (and debugfs decodes) GuC submission statistics which should be
indexed by driver-engine-id rather then guc-engine-id.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466432287-5799-1-git-send-email-david.s.gordon@intel.com
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a121.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a121 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add initial support for big endian by always writing the pte
in le32. Note, revisit if hardware capable of doing big endian
fetches.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Rockchip just blew up here on testing, because I removed some "is this
crtc already disabled/enabled" state tracking from callbacks (not needed
with atomic). Turns out that was needed to work around rockchip still
calling legacy helper code.
Since me explaining on irc/mailing-list plus kerneldoc isn't enough,
be more verbose and add dmesg output. Not that anyone actually reads that,
either.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465388359-8070-26-git-send-email-daniel.vetter@ffwll.ch
krealloc() must not be used against devm_*() allocated
memory regions:
- if a bigger memory is to be allocated, krealloc() and
__krealloc() could return a different pointer than the
one given to them, creating a memory region which is not
managed, thus it will not be automatically released on
device removal.
- if a bigger memory is to be allocated, krealloc() could
kfree() the managed memory region which is passed to it.
The old pointer is left registered as a resource for the
device. On device removal, this dangling pointer will be
used and an unrelated memory region could be released.
- if the requested size is equal to 0, krealloc() can also
just behave like kfree(). Here too, the old pointer is
kept associated with the device. On device removal, this
invalid pointer will be used and an unrelated memory
region could be released.
For all these reasons, krealloc() must not be used on a
pointer returned by devm_*() functions.
Cc: Tejun Heo <tj@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Since commit 3ef0e5ba46 ('slab: introduce kzfree()'),
kfree() is no more the only function to be considered:
kzfree() should be recognized too.
In particular, kzfree() must not be called on memory
allocated through devm_*() functions.
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Mediatek SoC's M4U has two generations of HW architcture. Generation one
uses flat, one layer pagetable, and was shipped with ARM architecture, it
only supports 4K size page mapping. MT2701 SoC uses this generation one
m4u HW. Generation two uses the ARM short-descriptor translation table
format for address translation, and was shipped with ARM64 architecture,
MT8173 uses this generation two m4u HW. All the two generation iommu HW
only have one iommu domain, and all its iommu clients share the same
iova address.
These two generation m4u HW have slit different register groups and
register offset, but most register names are the same. This patch add iommu
support for mediatek SoC mt2701.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Mediatek SMI has two generations of HW architecture, mt8173 uses the
second generation of SMI HW while mt2701 uses the first generation
HW of SMI.
There's slight differences between the two generations, for generation 2,
the register which control the iommu port access PA or IOVA is at each
larb's register base. But for generation 1, the register is at smi ao
base(smi always on register base).
Besides that, the smi async clock should be prepared and enabled for SMI
generation 1 HW to transform the smi clock into emi clock domain, but is
not needed for SMI generation 2.
This patch add SMI driver for mt2701 which use generation 1 SMI HW.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move the struct defines of mtk iommu into a new header files for
common use.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch defines the local arbitor port IDs for mediatek SoC MT2701 and
add descriptions of binding for mediatek generation one iommu and smi.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The device_node will be released in of_iommu_configure, it may be double
released if call of_node_put in mtk_iommu_of_xlate.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch hooks up the support for device power domain provided by
SCPI using the Linux generic power domain infrastructure.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The System Control Processor (SCP) provides peripheral devices with
power domains that can be enabled and disabled viathe System Control
and Power Interface (SCPI) Message Protocol. Add bindings to allow
probing of these device power domians.
Cc: Rob Herring <robh+dt@kernel.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCPI protocol supports device power state management. This deals with
power states of various peripheral devices in the system other than the
core compute subsystem.
This patch adds support for the power state management of those
peripheral devices.
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
&fault->work), is involved in IO page-fault handling.
WQ_MEM_RECLAIM has been set to guarantee forward progress under memory
pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Jiri Pirko says:
====================
mlxsw: Preparation for IPv4 router
Ido says:
This series prepares the driver for IPv4 router support. The router follow-up
patches are available at: https://github.com/jpirko/linux_mlxsw/tree/net-next_queue
Patches 1-9 simplify the netdevice notification block and also add several
checks during PRECHANGEUPPER events against topologies that aren't supported by
the device. This will ensure L3 interfaces are only configured on top of
valid netdevs.
Patches 10-13 contain trivial changes required for the introduction of a generic
FID struct - currently only used for vFIDs - in patch 14. Making the FID
struct generic will allow us to easily associate the underlying FIDs with
their L3-counterparts - Router interfaces (RIFs):
FID Type | Used by | RIF Type
--------------------------------------------------------
FID | The VLAN-aware bridge | VLAN
vFID | VLAN-unaware bridges | FID
rFID | non-bridged netdevs (follow-up) | Sub-port
Obligatory ASCII art to visualize the above:
A.B.C.D
+
| FID RIF
+
br0 E.F.G.H
+ +
| | VLAN RIF
+---------+---------+ +
| | br1.W
| vFID | +
| | |
vPort +-+-+ +-+-+ +
swXpY.Z | | | | br1
+-+-+ +-+-+ +
| | FID=W |
| | +------------+------------+
| | | |
+---+---+ +---+-+-+ +---+---+
| | | | | |
| | | | | |
| | | | | |
+-------+ +-------+ +-------+
swXpY
Patches 15-16 further generalize the struct by exploiting the fact that the
FID is a shared resource among ports. Each FID type is assigned a 'leave'
function that is invoked based on CHANGEUPPER events and takes care of the
necessary clean-up.
Patches 17-22 build upon the previous patches and use the FID struct for the
VLAN-aware bridge and take care of cleaning up FID resources in the 'leave'
functions. For now, these are only FDB records, but later on we'll have to
remove the RIFs associated with these FIDs, which will in turn take care of
routes and neighbours clean-up.
The last patch adds debug prints that proved very useful during the
development of this series.
Tested with the existing L2 recipes:
https://github.com/jpirko/lnst/tree/master/recipes/switchdev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).
Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vPort is created or when it joins a bridge we always do the same
set of operations:
1) Create the vFID, if not already created
2) Setup flooding for the vFID
3) Map the {Port, VID} to the vFID
When a vPort is destroyed or when it leaves a bridge the reverse is
performed.
Encapsulate the above in join / leave functions and simplify the code.
FIDs and rFIDs will use a similar set of functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FID used by a vPort (vFID, but also rFID later in the series) is
always mapped using {Port, VID} and not only VID as with the 4K FIDs of
the VLAN-aware bridge.
Instead of specifying all the arguments each time, just wrap this
operation using a dedicated function and simplify the code.
As before, the function takes FID as its argument in preparation for a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and use only one function for vFID creation /
destruction.
Unlike before, the function receives a FID index as its argument and not
a vFID index. Instead of passing 0, now one would need to pass 4K, which
is the first vFID.
This is the first step in creating a generic FID struct that will be
used for all three types of FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a macro to do this kind of declarations, so use it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold a reference count on the number of ports member in the
VLAN-aware bridge, as we only support one.
Instead of always incrementing / decrementing the reference count after
joining / leaving the bridge, simply do this accounting in the join /
leave functions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'br_dev' is never used, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When responding to unlinking CHANGEUPPER notifications we shouldn't
return any value, as it's not checked by upper layers.
In addition, there's nothing the driver can do in case of failure, so it
should simply continue and try to free as much resources as possible and
not stop on first error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking for a condition and then issue the warning, just do
it in one go and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When upper device of a VLAN device changes we already made sure it's
a bridge device in PRECHANGEUPPER, so no need to check it's a master
device in CHANGEUPPER.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port netdev is put under LAG it cannot have VLAN upper devices,
so forbid that. The LAG device itself can have VLAN upper devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only support the following upper devices for port netdevs:
1) Bridge
2) LAG (bond / team)
3) VLAN
Any other device is forbidden, so return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking the error value and returning NOTIFY_BAD, just use
notifier_from_errno() and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-8-git-send-email-chris@chris-wilson.co.uk
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-7-git-send-email-chris@chris-wilson.co.uk
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-6-git-send-email-chris@chris-wilson.co.uk
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-5-git-send-email-chris@chris-wilson.co.uk
Up to now, the recommendation was for drivers to call drm_dev_register()
followed by drm_connector_register_all(). Now that
drm_connector_register() is safe against multiple invocations, we can
move drm_connector_register_all() to drm_dev_register() and not suffer
from any backwards compatibility issues with drivers not following the
more rigorous init ordering.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466151923-1572-4-git-send-email-chris@chris-wilson.co.uk
