Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Newer Keystone 2 devices utilize pinmuxing. Enable PINCTRL SINGLE
which is used to handle pinmuxing.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Some Keystone 2 devices utilize pinmuxing which requires PINCTRL
to be enabled. Therefore, enable PINCTRL for all Keystone 2 devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add pinctrl node and populate the pinctrl registers with the default
values.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The PCI DT bindings contain a bogus entry for IO space which is not
supported on Keystone. The current bogus entry has an invalid size
and throws following error during boot.
[0.420713] keystone-pcie 21021000.pcie: error -22: failed to map
resource [io 0x0000-0x400000003fff]
So remove it from the dts. While at it also add a bus-range
value that eliminates following log at boot up.
[0.420659] No bus range found for /soc/pcie@21020000, using [bus 00-ff]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
policy->freq_table will always be valid for this platform, otherwise
driver's probe() would fail. And so this routine will *always* return
after calling cpufreq_frequency_table_verify().
This can be done using the generic callback provided by core, lets use
it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This routine can't fail unless the frequency table is invalid and
doesn't contain any valid entries.
Make it return the index and WARN() in case it is used for an invalid
table.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is already present as part of the policy and so no need to pass it
from the caller. Also, 'freq_table' is guaranteed to be valid in this
function and so no need to check it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy already has this pointer set, use it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is absolutely no need to keep a copy to the freq-table in 'struct
od_policy_dbs_info'. Use policy->freq_table instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the callers of cpufreq_frequency_get_table() already have the
pointer to a valid 'policy' structure and they don't really need to go
through the per-cpu variable first and then a check to validate the
frequency, in order to find the freq-table for the policy.
Directly use the policy->freq_table field instead for them.
Only one user of that API is left after above changes, cpu_cooling.c and
it accesses the freq_table in a racy way as the policy can get freed in
between.
Fix it by using cpufreq_cpu_get() properly.
Since there are no more users of cpufreq_frequency_get_table() left, get
rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com> (cpu_cooling.c)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These aren't required at all, remove them.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using flat regmap cache instead of RB-tree to avoid the following
lockdep warning on driver load:
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x15c/0x160()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
The RB-tree regmap cache needs to allocate new space on first
writes. However, allocations in an atomic context (e.g. when a
spinlock is held) are not allowed. The function regmap_write
calls map->lock, which acquires a spinlock in the fast_io case.
Since the FSL DCU driver uses MMIO, the regmap bus of type
regmap_mmio is being used which has fast_io set to true.
Use flat regmap cache and specify max register to be large
enouth to cover all registers available in LS1021a and Vybrids
register space.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Because we define WRITE/READ as REQ_OPs, we cannot do
switch (rq_data_dir(request))
case READ
....
case WRITE
...
without getting warnings about handling other REQ_OPs.
This just has mq_disk do a if/else like it does in other
places.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This was missed from my last patchset.
This patch has ext4 crypto code use the bio op helper
to set the operation. The operation (discard, write, writesame,
etc) is now defined seperately from the other REQ bits. They
still share the bi_rw field to save space, so we use these
helpers so modules do not have to worry about setting/overwriting
info.
Jens, I am not sure how you handle patches on top of patches
in the next branches. If you merge patches that fix issues
in previous patches in next, then this patch could be part
of
commit 95fe6c1a20
Author: Mike Christie <mchristi@redhat.com>
Date: Sun Jun 5 14:31:48 2016 -0500
block, fs, mm, drivers: use bio set/get op accessors
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Kill with signal number 0 is commonly used for checking PID existence.
Smack treated such cases like any other kills, although no signal is
actually delivered when sig == 0.
Checking permissions when sig == 0 didn't prevent an unprivileged caller
from learning whether PID exists or not. When it existed, kernel returned
EPERM, when it didn't - ESRCH. The only effect of policy check in such
case is noise in audit logs.
This change lets Smack silently ignore kill() invocations with sig == 0.
Signed-off-by: Rafal Krypa <r.krypa@samsung.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
The whole menu depends on X86 so there is no point in repeating this
dependency on individual driver entries.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Lenovo Thinkpad devices T460, T460s, T460p, T560, X260 use
HKEY version 0x200 without adaptive keyboard.
HKEY version 0x200 has method MHKA with one parameter value.
Passing parameter value 1 will get hotkey_all_mask (the same like
HKEY version 0x100 without parameter). Passing parameter value 2 to
MHKA method will retrieve hotkey_all_adaptive_mask. If 0 is returned in
that case there is no adaptive keyboard available.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Lyude <cpaul@redhat.com>
Tested-by: Marco Trevisan <marco@ubuntu.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
[dvhart: Keep MHKA error string on one line in new and existing pr_err calls]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Newer ideapads support a new mic hotkey implemented via an ACPI
interface. This patch converts the mic mute event to a keycode
KEY_MICMUTE.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The symbol PWMF_ENABLED is defined via an enum, which is not defined
at the time the preprocessor passes through "kernel_ver.h". So we
can't use it in an #if statement expression.
Use the Linux kernel version instead.
Change-Id: Id427224b1dfecfd886fcdae89c4bcf711b616439
Signed-off-by: Alex Elder <elder@linaro.org>
Use CC_SET()/CC_OUT() and static_cpu_has(). This produces code good
enough to eliminate ad hoc use of alternatives in <asm/archrandom.h>,
greatly simplifying the code.
While we are at it, make x86_init_rdrand() compile out completely if
we don't need it.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1465414726-197858-11-git-send-email-hpa@linux.intel.com
v2: fix a conflict between <linux/random.h> and <asm/archrandom.h>
discovered by Ingo Molnar. There are a few places in x86-specific
code where we need all of <arch/archrandom.h> even when
CONFIG_ARCH_RANDOM is disabled, so <linux/random.h> does not
suffice.
Remove open-coded uses of set instructions to use CC_SET()/CC_OUT() in
arch/x86/boot/boot.h.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1465414726-197858-10-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Remove open-coded uses of set instructions to use CC_SET()/CC_OUT() in
<asm/rwsem.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-9-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Remove open-coded uses of set instructions to use CC_SET()/CC_OUT() in
<asm/percpu.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-8-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Remove open-coded uses of set instructions to use CC_SET()/CC_OUT() in
<asm/bitops.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-7-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Change the GEN_*_RMWcc() macros to use the CC_SET()/CC_OUT() macros
defined in <asm/asm.h>, and disable the use of asm goto if
__GCC_ASM_FLAG_OUTPUTS__ is enabled. This allows gcc to receive the
flags output directly in gcc 6+.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-6-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
The CC_SET() and CC_OUT() macros can be used together to take
advantage of the new __GCC_ASM_FLAG_OUTPUTS__ feature in gcc 6+ while
remaining backwards compatible. CC_SET() generates a SET instruction
on older compilers; CC_OUT() makes sure the output is received in the
correct variable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-5-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Change the lexical defintion of the GEN_*_RMWcc() macros to not take
the condition code as a quoted string. This will help support
changing them to use the new __GCC_ASM_FLAG_OUTPUTS__ feature in a
subsequent patch.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-4-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
The gcc people have confirmed that using "bool" when combined with
inline assembly always is treated as a byte-sized operand that can be
assumed to be 0 or 1, which is exactly what the SET instruction
emits. Change the output types and intermediate variables of as many
operations as practical to "bool".
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-3-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Use SETC instead of SBB to return the value of CF from assembly. Using
SETcc enables uniformity with other flags-returning pieces of assembly
code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1465414726-197858-2-git-send-email-hpa@linux.intel.com
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
The notion of which uart instance is serial0 or serial1
is board specific rather than generic to the chip. This
patch removes the serial aliases from generic chip dtsi
and adds an appropriate alias to the board specific dtsi.
By making the alias for serial0 point to uart1 for the arria10_socdk,
the linux boot command line supports specifying console=ttyS0,115200
for backwards compatibility, and it supports not specifying
the console at all.
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Without having an ethernet alias, ethernet will have a random MAC address,
versus take an address that was provided from the bootloader.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
David Ahern says:
====================
net: vrf: Improve use of FIB rules
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This solution still allows a user to insert their own rules for VRFs,
including rules with additional attributes. Accordingly, it is backwards
compatible with existing setups and allows other policy routing as
desired.
Hopefully v5 is the charm; my e-waste can is getting full.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add l3mdev rule per address family when the first VRF device is
created. The rules are installed with a default preference of 1000.
Users can replace the default rule as desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: two small fixes
We fix a couple of rarely seen anomalies discovered during testing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The node keepalive interval is recalculated at each timer expiration
to catch any changes in the link tolerance, and stored in a field in
struct tipc_node. We use jiffies as unit for the stored value.
This is suboptimal, because it makes the calculation unnecessary
complex, including two unit conversions. The conversions also lead to
a rounding error that causes the link "abort limit" to be 3 in the
normal case, instead of 4, as intended. This again leads to unnecessary
link resets when the network is pushed close to its limit, e.g., in an
environment with hundreds of nodes or namesapces.
In this commit, we do instead let the keepalive value be calculated and
stored in milliseconds, so that there is only one conversion and the
rounding error is eliminated.
We also remove a redundant "keepalive" field in struct tipc_link. This
is remnant from the previous implementation.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 88e8ac7000 ("tipc: reduce transmission rate of reset messages
when link is down") revealed a flaw in the node FSM, as defined in
the log of commit 66996b6c47 ("tipc: extend node FSM").
We see the following scenario:
1: Node B receives a RESET message from node A before its link endpoint
is fully up, i.e., the node FSM is in state SELF_UP_PEER_COMING. This
event will not change the node FSM state, but the (distinct) link FSM
will move to state RESETTING.
2: As an effect of the previous event, the local endpoint on B will
declare node A lost, and post the event SELF_DOWN to the its node
FSM. This moves the FSM state to SELF_DOWN_PEER_LEAVING, meaning
that no messages will be accepted from A until it receives another
RESET message that confirms that A's endpoint has been reset. This
is wasteful, since we know this as a fact already from the first
received RESET, but worse is that the link instance's FSM has not
wasted this information, but instead moved on to state ESTABLISHING,
meaning that it repeatedly sends out ACTIVATE messages to the reset
peer A.
3: Node A will receive one of the ACTIVATE messages, move its link FSM
to state ESTABLISHED, and start repeatedly sending out STATE messages
to node B.
4: Node B will consistently drop these messages, since it can only accept
accept a RESET according to its node FSM.
5: After four lost STATE messages node A will reset its link and start
repeatedly sending out RESET messages to B.
6: Because of the reduced send rate for RESET messages, it is very
likely that A will receive an ACTIVATE (which is sent out at a much
higher frequency) before it gets the chance to send a RESET, and A
may hence quickly move back to state ESTABLISHED and continue sending
out STATE messages, which will again be dropped by B.
7: GOTO 5.
8: After having repeated the cycle 5-7 a number of times, node A will
by chance get in between with sending a RESET, and the situation is
resolved.
Unfortunately, we have seen that it may take a substantial amount of
time before this vicious loop is broken, sometimes in the order of
minutes.
We correct this by making a small correction to the node FSM: When a
node in state SELF_UP_PEER_COMING receives a SELF_DOWN event, it now
moves directly back to state SELF_DOWN_PEER_DOWN, instead of as now
SELF_DOWN_PEER_LEAVING. This is logically consistent, since we don't
need to wait for RESET confirmation from of an endpoint that we alread
know has been reset. It also means that node B in the scenario above
will not be dropping incoming STATE messages, and the link can come up
immediately.
Finally, a symmetry comparison reveals that the FSM has a similar
error when receiving the event PEER_DOWN in state PEER_UP_SELF_COMING.
Instead of moving to PERR_DOWN_SELF_LEAVING, it should move directly
to SELF_DOWN_PEER_DOWN. Although we have never seen any negative effect
of this logical error, we choose fix this one, too.
The node FSM looks as follows after those changes:
+----------------------------------------+
| PEER_DOWN_EVT|
| |
+------------------------+----------------+ |
|SELF_DOWN_EVT | | |
| | | |
| +-----------+ +-----------+ |
| |NODE_ | |NODE_ | |
| +----------|FAILINGOVER|<---------|SYNCHING |-----------+ |
| |SELF_ +-----------+ FAILOVER_+-----------+ PEER_ | |
| |DOWN_EVT | A BEGIN_EVT A | DOWN_EVT| |
| | | | | | | |
| | | | | | | |
| | |FAILOVER_ |FAILOVER_ |SYNCH_ |SYNCH_ | |
| | |END_EVT |BEGIN_EVT |BEGIN_EVT|END_EVT | |
| | | | | | | |
| | | | | | | |
| | | +--------------+ | | |
| | +-------->| SELF_UP_ |<-------+ | |
| | +-----------------| PEER_UP |----------------+ | |
| | |SELF_DOWN_EVT +--------------+ PEER_DOWN_EVT| | |
| | | A A | | |
| | | | | | | |
| | | PEER_UP_EVT| |SELF_UP_EVT | | |
| | | | | | | |
V V V | | V V V
+------------+ +-----------+ +-----------+ +------------+
|SELF_DOWN_ | |SELF_UP_ | |PEER_UP_ | |PEER_DOWN |
|PEER_LEAVING| |PEER_COMING| |SELF_COMING| |SELF_LEAVING|
+------------+ +-----------+ +-----------+ +------------+
| | A A | |
| | | | | |
| SELF_ | |SELF_ |PEER_ |PEER_ |
| DOWN_EVT| |UP_EVT |UP_EVT |DOWN_EVT |
| | | | | |
| | | | | |
| | +--------------+ | |
|PEER_DOWN_EVT +--->| SELF_DOWN_ |<---+ SELF_DOWN_EVT|
+------------------->| PEER_DOWN |<--------------------+
+--------------+
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: misc improvements
This patch series builds on top of Andrew's "New DSA bind, switches as devices"
patch set and does the following:
- add a few helper functions/goodies for net/dsa/dsa2.c to be as close as possible
from net/dsa/dsa.c in terms of what drivers can expect, in particular the slave
MDIO bus and the enabled_port_mask and phy_mii_mask
- fix the CPU port ethtools ops to work in a multiple tree setup since we can
no longer assume a single tree is supported
- make the bcm_sf2 driver register its own MDIO bus, yet assign it to
ds->slave_mii_bus for everything to work in net/dsa/slave.c wrt. PHY probing,
this is a tad cleaner than what we have now
Changes in v2:
Most of the previous patches have been dropped to just keep the relevant ones
now.
Changes in v3:
- split the addition of the slave MII bus as a separate patch
- properly unwind all operations at the right place and right time (ethtool ops,
slave MDIO bus
- fixed a few typos here and there
Changes in v4:
- removed superfluous dst agrument to dsa_cpu_port_ethtool_{setup,restore}
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can properly support multiple distinct trees in the system,
using a global variable: dsa_cpu_port_ethtool_ops is getting clobbered
as soon as the second switch tree gets probed, and we don't want that.
We need to move this to be dynamically allocated, and since we can't
really be comparing addresses anymore to determine first time
initialization versus any other times, just move this to dsa.c and
dsa2.c where the remainder of the dst/ds initialization happens.
The operations teardown restores the master netdev's ethtool_ops to its
original ethtool_ops pointer (typically within the Ethernet driver)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function: dsa_cpu_port_ethtool_init() which initializes a
custom ethtool_ops structure with custom DSA ethtool operations for CPU
ports. This is a preliminary change to move the initialization outside
of net/dsa/slave.c.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mimic what net/dsa/dsa.c does and provide a slave MII bus by default
which will be created if the driver implements a phy_read method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers rely on these two bitmasks to contain the correct values
for them to successfully probe and initialize at drv->setup() time,
calculate correct values to put in both masks as early as possible in
dsa_get_ports_dn().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we have multiples trees and switches with the same index, we
need to add another discriminating id: the switch tree.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:168: warning: No description found for parameter 'running'
.//include/linux/netdevice.h:1867: warning: No description found for parameter 'qdisc_running_key'
Fixes: f9eb8aea2a ("net_sched: transform qdisc running bit into a seqcount")
Fixes: edb09eb17e ("net: sched: do not acquire qdisc spinlock in qdisc/class stats dump")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
