Just use the previously prepared infrastructure and offload the gact
trap action to ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use trap/discard flex action to implement trap.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an ACL trap and put it into ip2me trap group.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "trap_id" is 9bits long. So far, this was not a problem since we
used only traps with ids that fit into 8bits. But the ACL traps that are
going to be introduced use the 9th bit.
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper called is_tcf_gact_trap which could be used to
tell if the action is gact trap or not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is need to instruct the HW offloaded path to push certain matched
packets to cpu/kernel for further analysis. So this patch introduces a
new TRAP control action to TC.
For kernel datapath, this action does not make much sense. So with the
same logic as in HW, new TRAP behaves similar to STOLEN. The skb is just
dropped in the datapath (and virtually ejected to an upper level, which
does not exist in case of kernel).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZNnBiAAoJEAhfPr2O5OEV9bwP/1bus9tAw3AT+HxRSIaFFX8+
DMDmJ6nZ4WQJ4fI04tKkUjpl+G2ImDGshdGgLht/YpaJRd6KgPqV+zWrAVX5/0e1
mLyhjaALuk5M//JbkxEP95SWBOZ6SCIWlV/5oQRTNI86kO0gISxoCAsbumKlSSUC
qTFmbmPp9siFpS43eZjVcgYIbwFx75qvLTc1+JRvxa2VhtMB5d4xYnXSpxlCvduj
NN14KiphBgCOvyMQsi4q3H6ma8EL0sEtaukqPzXOnz6GGAIUUbDA23APM5H0LIIZ
kYhO9ooez4dz1094ex1zSS/uQq2ogCTv7ShQseddNbHhOFG7Aq30AXLMEWeHaNp1
fFb28CY3CBpNaYfjePbqIs8KKg3JxmJGmCGgW65p40UGUo1Itbpci5MqN8BjQAI8
Ks1rf+V4iYQTr4QmQJQqCyJCljrsQbGMKZ9I67pmqfbqDunlH43Zr88DEWPv3rbW
qac6U1vh108UHE/1KRZFjzvo31ToP+f+AwyVTXVeIi6vba2gvC8ASCJnZ/nGtO74
Eb/GR0DtqvYGE6sXohbMywZ+8wRR6CdRVDC4YotQwaoghwnH10WPLg3JahECVMu7
MbDtVvUHjbJ18cqwCW+J01gcuQxH/8Lx07T9T+pUFFanPBT7phPiQ/UAEPL1e3XO
e4nFwX9h78wISBdy8Yx7
=+jBV
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some bug fixes:
- Don't fail build if atomisp has warnings
- Some CEC Kconfig changes to allow it to be used by DRM without
media dependencies
- A race fix at RC initialization code
- A driver fix at rainshadow-cec
IMHO, the one that affects most people in this series is a build fix:
if you try to build the Kernel with W=1 or using gcc7 and
all[yes|mod]config, build will fail due to -Werror at atomisp
makefiles"
* tag 'media/v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
The clipped src coordinates have already been rotated by 270 degrees for
when the plane rotation is 90/270 degrees, hence the FBC code should no
longer swap the width and height.
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-4-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.
For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.
v2: Resolve conflicts from SKL+ wm rework
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-3-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The check to see of err is set and the subsequent goto is extraneous
as the next statement is where the goto is jumping to. Remove this
redundant check and goto.
Detected by CoverityScan, CID#1437734 ("Identical code for
different branches")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-06-06
This series contains fixes to i40e and i40evf only.
Mauro S. M. Rodrigues fixes a flood in the kernel log which was introduced
in a previous commit because of a mistaken substitution of __I40E_VSI_DOWN
instead of __I40E_DOWN when testing the state of the PF.
Björn Töpel fixes an issue introduced in a previous commit where the
offset was incorrect and could lead to data corruption for architectures
using PAGE_SIZE larger than 8191. Fixed the issue by updating the
page_offset correctly using the proper setting for truesize.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from commit b63a16f6cd ("drm/i915: Compute display surface
offset in the plane check hook for SKL+") we've already rotated the src
coordinates by 270 degrees by the time we check if a scaler is needed
or not, so we must not account for the rotation a second time.
Previously we did these steps in the opposite order and hence the
scaler check had to deal with rotation itself. The double rotation
handling causes us to enable a scaler pretty much every time 90/270
degree plane rotation is requested, leading to fuzzier fonts and whatnot.
v2: s/unsigned/unsigned int/ to appease checkpatch
v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=M7Pr
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20170606' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Support service upgrade
Here's a set of patches that allow AF_RXRPC to support the AuriStor service
upgrade facility. This allows the server to change the service ID
requested to an upgraded service if the client requests it upon the
initiation of a connection.
This is used by the AuriStor AFS-compatible servers to implement IPv6
handling and improved facilities by providing improved volume location,
volume, protection, file and cache management services. Note that certain
parts of the AFS protocol carry hard-coded IPv4 addresses.
The reason AuriStor does it this way is that probing the improved service
ID first will not incur an ABORT or any other response on some servers if
the server is not listening on it - and so one have to employ a timeout.
This is implemented in the server by allowing an AF_RXRPC server to call
bind() twice on a socket to allow it to listen on two service IDs and then
call setsockopt() to instruct the server to upgrade one into the other if
the client requests it (by setting userStatus to 1 on the first DATA packet
on a connection). If the upgrade occurs, all further operations on that
connection are done with the new service ID. AF_RXRPC has to handle this
automatically as connections are not exposed to userspace.
Clients can request this facility by setting an RXRPC_UPGRADE_SERVICE
command in the sendmsg() control buffer and then observing the resultant
service ID in the msg_addr returned by recvmsg(). This should only be used
to probe the service. Clients should then use the returned service ID in
all subsequent communications with that server. Note that the kernel will
not retain this information should the connection expire from its cache.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We're not that short on characters that we can't spell out
"false_color". Saves me from figuring out what "fc" means
the next time look at the code.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124412.5335-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The number of compressed segments has been available ever since
FBC2 was introduced in g4x, it just moved from the STATUS register
into STATUS2 on IVB.
For FBC1 if we really wanted the number of compressed segments we'd
have to trawl through the tags, but in this case since the code just
uses the number of compressed segments as an indicator whether
compression has occurred we can just check the state of the
COMPRESSING and COMPRESSED bits. IIRC the hardware will try to
periodically recompress all uncompressed lines even if they haven't
changed and the COMPRESSED bit will be cleared while the compressor
is running, so just checking the COMPRESSED bit might not give us
the right answer. Hence it seems better to check for both
COMPRESSED and COMPRESSING as that should tell us that the
compressor is at least trying to do something.
While at it move the IVB+ register define to the right place, unify
the naming convention of the compressed segment count masks, and
fix up the mask for g4x.
v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> # SNB
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # ilk+
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # pre-ilk
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124318.31755-1-ville.syrjala@linux.intel.com
When direct issue is done on request picked up from plug list,
the hctx need to be updated with the actual hw queue, otherwise
wrong hctx is used and may hurt performance, especially when
wrong SRCU readlock is acquired/released
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-06-06
This series contains updates and fixes to e1000e and igb.
Matwey V Kornilov fixes an issue where igb_get_phy_id_82575() relies on
the fact that page 0 is already selected, but this is not the case after
igb_read_phy_reg_gs40g()/igb_write_phy_reg_gs40g() were removed in a
previous commit. This leads to initialization failure and some devices
not working. To fix the issue, explicitly select page 0 before first
access to PHY registers.
Arnd Bergmann modifies the driver to avoid a "defined but not used"
warning by removing #ifdefs and using __maybe_unused annotation instead
for new power management functions.
Jake provides most of the changes in the series, all around PTP and
timestamp fixes/updates. Resolved several race conditions based on
the hardware can only handle one transmit timestamp at a time, so
fix the locking logic, as well as create a statistic for "skipped"
timestamps to help administrators identify issues.
Benjamin Poirier provides 2 changes, first to igb to remove the
second argument to igb_update_stats() since it always passes the
same two arguments. So instead of having to pass the second argument,
just update the function to the necessary information from the adapter
structure. Second modifies the e1000e_get_stats64() call to
dev_get_stats() to avoid ethtool garbage being reported.
Konstantin Khlebnikov modifies e1000e to use disable_hardirq(), instead
of disable_irq() for MSIx vectors in e1000_netpoll().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b699d00358.
As per Eric Dumazet, the pskb_may_pull() is a NOP in this
particular case, so the 'iph' reload is unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
The scanline counter is bonkers on VLV/CHV DSI. The scanline counter
increment is not lined up with the start of vblank like it is on
every other platform and output type. This causes problems for
both the vblank timestamping and atomic update vblank evasion.
On my FFRD8 machine at least, the scanline counter increment
happens about 1/3 of a scanline ahead of the start of vblank (which
is where all register latching happens still). That means we can't
trust the scanline counter to tell us whether we're in vblank or not
while we're on that particular line. In order to keep vblank
timestamping in working condition when called from the vblank irq,
we'll leave scanline_offset at one, which means that the entire
line containing the start of vblank is considered to be inside
the vblank.
For the vblank evasion we'll need to consider that entire line
to be bad, since we can't tell whether the registers already
got latched or not. And we can't actually use the start of vblank
interrupt to get us past that line as the interrupt would fire
too soon, and then we'd up waiting for the next start of vblank
instead. One way around that would using the frame start
interrupt instead since that wouldn't fire until the next
scanline, but that would require some bigger changes in the
interrupt code. So for simplicity we'll just poll until we get
past the bad line.
v2: Adjust the comments a bit
Cc: stable@vger.kernel.org
Cc: Jonas Aaberg <cja@gmx.net>
Tested-by: Jonas Aaberg <cja@gmx.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161215174734.28779-1-ville.syrjala@linux.intel.com
Tested-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
The help info of `make C=1` is little confusing, make it clear.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This fixes a regression introduced by ebc9446135 ("drm:
convert drivers to use drm_of_find_panel_or_bridge") that was
recently merged, causing HDMI output to not work.
For the kirin driver, the port value should be 1 instead of 0,
so this oneline patch fixes it and gets graphics working again.
Cc: Rob Herring <robh@kernel.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Fix-suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1495557626-25285-1-git-send-email-john.stultz@linaro.org
The driver supports a single input only, which can be either analog or
digital. If the subdevice supports dv_timings_cap the input is digital
and the driver should not fill in the standard.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a bug where the copying of scatterlist buffers incorrectly
ignored bytes to skip in a scatterlist and ended 1 byte short.
This fixes testmgr hmac and hash test failures currently obscured
by hash import/export not being supported.
Fixes: abefd6741d ("staging: ccree: introduce CryptoCell HW driver").
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have aligned argument with parenthesis, so checkpatch no check also.
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed the checkpatch.pl warning:
WARNING: line over 80 characters
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a space around logical symbol '|' to wipe out checkpatch check
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed checkpatch warning by adding a blank line after declare
expression
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Noticed by FORTIFY_SOURCE, this swaps memcpy() for strncpy() to zero-value
fill the end of the buffer instead of over-reading a string from .rodata.
Signed-off-by: Daniel Micay <danielmicay@gmail.com>
[kees: wrote commit log]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wayne Porter <wporter82@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace cant with cannot, argumetns with arguments and
add line break to overly long DBG_871X statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver may sleep under a spin lock, and the function call path is:
rtsx_exclusive_enter_ss (acquire the lock by spin_lock)
rtsx_enter_ss
rtsx_power_off_card
xd_cleanup_work
xd_delay_write
xd_finish_write
xd_copy_page
wait_timeout
schedule_timeout --> may sleep
To fix it, "wait_timeout" is replaced with mdelay in xd_copy_page.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the default screen resolution and also use 24bpp for a better
screen performance.
Tested-by: Teddy Wang <teddy.wang@siliconmotion.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: CPU: 3 PID: 2840 at arch/x86/kvm/vmx.c:10966 nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel]
CPU: 3 PID: 2840 Comm: qemu-system-x86 Tainted: G OE 4.12.0-rc3+ #23
RIP: 0010:nested_vmx_vmexit+0xdcd/0xde0 [kvm_intel]
Call Trace:
? kvm_check_async_pf_completion+0xef/0x120 [kvm]
? rcu_read_lock_sched_held+0x79/0x80
vmx_queue_exception+0x104/0x160 [kvm_intel]
? vmx_queue_exception+0x104/0x160 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x1171/0x1ce0 [kvm]
? kvm_arch_vcpu_load+0x47/0x240 [kvm]
? kvm_arch_vcpu_load+0x62/0x240 [kvm]
kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
? kvm_vcpu_ioctl+0x384/0x7b0 [kvm]
? __fget+0xf3/0x210
do_vfs_ioctl+0xa4/0x700
? __fget+0x114/0x210
SyS_ioctl+0x79/0x90
do_syscall_64+0x81/0x220
entry_SYSCALL64_slow_path+0x25/0x25
This is triggered occasionally by running both win7 and win2016 in L2, in
addition, EPT is disabled on both L1 and L2. It can't be reproduced easily.
Commit 0b6ac343fc (KVM: nVMX: Correct handling of exception injection) mentioned
that "KVM wants to inject page-faults which it got to the guest. This function
assumes it is called with the exit reason in vmcs02 being a #PF exception".
Commit e011c663 (KVM: nVMX: Check all exceptions for intercept during delivery to
L2) allows to check all exceptions for intercept during delivery to L2. However,
there is no guarantee the exit reason is exception currently, when there is an
external interrupt occurred on host, maybe a time interrupt for host which should
not be injected to guest, and somewhere queues an exception, then the function
nested_vmx_check_exception() will be called and the vmexit emulation codes will
try to emulate the "Acknowledge interrupt on exit" behavior, the warning is
triggered.
Reusing the exit reason from the L2->L0 vmexit is wrong in this case,
the reason must always be EXCEPTION_NMI when injecting an exception into
L1 as a nested vmexit.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: e011c663b9 ("KVM: nVMX: Check all exceptions for intercept during delivery to L2")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This mouse is also known under other IDs. It needs the quirk
ALWAYS_POLL or will disconnect in runlevel 1 or 3.
Signed-off-by: Sebastian Parschauer <sparschauer@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The rcar-vin driver only uses one pad, pad number 0.
- All v4l2 operations that did not check that the requested operation
was for pad 0 have been updated with a check to enforce this.
- All v4l2 operations that stored (and later restored) the requested pad
before substituting it for the subdevice pad number have been updated
to not store the incoming pad and simply restore it to 0 after the
subdevice operation is complete.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use rvin_reset_format() in rvin_s_dv_timings() instead of just resetting
a few fields. This fixes an issue where the field format was not
properly set after S_DV_TIMINGS.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two were forgotten when refactoring the format reset code. If
they are not also reset at the same time as width and height the format
returned from G_FMT will not match reality.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All drivers have been converted from V4L2 OF to V4L2 fwnode. The V4L2 OF
framework is now unused. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of including the V4L2 OF header in ReST documentation, use the
V4L2 fwnode header instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
native_safe_halt enables interrupts, and you just shouldn't
call rcu_irq_enter() with interrupts enabled. Reorder the
call with the following local_irq_disable() to respect the
invariant.
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Remove the SNB PCH refclock init call from the runtime resume handler.
I don't think it was actually needed even when we had SNB runtime PM,
and if definitely isn't needed ever since SNB runtime PM was nuked in
commit d4c5636e74 ("drm/i915: Remove runtime PM for SNB").
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601183043.28543-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pass the more generic fwnode_handle to the init function than the
device_node.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add fwnode matching to complement OF node matching. And fwnode may also be
an OF node.
Do not enable fwnode matching yet. It will replace OF matching soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The fwnode_handle is a more generic way than OF device_node to describe
firmware nodes. Instead of the OF API, use more generic fwnode API to
obtain the same information.
As the V4L2 fwnode support will be required by a small minority of e.g.
ACPI based systems (the same might actually go for OF), make this a module
instead of embedding it in the videodev module.
The origins of the V4L2 fwnode framework is in the V4L2 OF framework.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lirc_zilog driver is the last remaining lirc driver, so the existing
todo is no longer relevant.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Inlining these functions into the probe function makes it much
more readable.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
