if Start Transfer command fails, let's try a little
harder to figure out why the command failed and give
slightly better return codes. This will be usefulf
or isochronous endpoints, at least, which could
decide to retry a given request.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.
In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Eric Dumazet says:
====================
net: avoid some atomic ops when FASYNC is not used
We can avoid some atomic operations on sockets not using FASYNC
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SOCKWQ_ASYNC_WAITDATA is set/cleared in sk_wait_data()
and equivalent functions, so that sock_wake_async() can send
a SIGIO only when necessary.
Since these atomic operations are really not needed unless
socket expressed interest in FASYNC, we can omit them in most
cases.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOCKWQ_ASYNC_NOSPACE is tested in sock_wake_async()
so that a SIGIO signal is sent when needed.
tcp_sendmsg() clears the bit.
tcp_poll() sets the bit when stream is not writeable.
We can avoid two atomic operations by first checking if socket
is actually interested in the FASYNC business (most sockets in
real applications do not use AIO, but select()/poll()/epoll())
This also removes one cache line miss to access sk->sk_wq->flags
in tcp_sendmsg()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: snmp: update SNMP methods
In the old days (before linux-3.0), SNMP counters were duplicated,
one set for user context, and anther one for BH context.
After commit 8f0ea0fe3a ("snmp: reduce percpu needs by 50%")
we have a single copy, and what really matters is preemption being
enabled or disabled, since we use this_cpu_inc() or __this_cpu_inc()
respectively.
This patch series kills the obsolete STATS_USER() helpers,
and rename all XXX_BH() helpers to __XXX() ones, to more
closely match conventions used to update per cpu variables.
This is probably going to hurt maintainers job for a while,
since cherry-picks will not be clean, but this had to be
cleaned at one point. I am so sorry guys.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing related to BH in SNMP counters anymore,
since linux-3.0.
Rename helpers to use __ prefix instead of _BH prefix,
for contexts where preemption is disabled.
This more closely matches convention used to update
percpu variables.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP6_UPD_PO_STATS_BH() to __IP6_UPD_PO_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP6_INC_STATS_BH() to __IP6_INC_STATS()
and IP6_ADD_STATS_BH() to __IP6_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename NET_INC_STATS_BH() to __NET_INC_STATS()
and NET_ADD_STATS_BH() to __NET_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP_UPD_PO_STATS_BH() to __IP_UPD_PO_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP6_INC_STATS_BH() to __ICMP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename IP_INC_STATS_BH() to __IP_INC_STATS(), to
better express this is used in non preemptible context.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename SCTP_INC_STATS_BH() to __SCTP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename UDP_INC_STATS_BH() to __UDP_INC_STATS(),
and UDP6_INC_STATS_BH() to __UDP6_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP_INC_STATS_BH() to __ICMP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename DCCP_INC_STATS_BH() to __DCCP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days (before linux-3.0), SNMP counters were duplicated,
one for user context, and one for BH context.
After commit 8f0ea0fe3a ("snmp: reduce percpu needs by 50%")
we have a single copy, and what really matters is preemption being
enabled or disabled, since we use this_cpu_inc() or __this_cpu_inc()
respectively.
We therefore kill SNMP_INC_STATS_USER(), SNMP_ADD_STATS_USER(),
NET_INC_STATS_USER(), NET_ADD_STATS_USER(), SCTP_INC_STATS_USER(),
SNMP_INC_STATS64_USER(), SNMP_ADD_STATS64_USER(), TCP_ADD_STATS_USER(),
UDP_INC_STATS_USER(), UDP6_INC_STATS_USER(), and XFRM_INC_STATS_USER()
Following patches will rename __BH helpers to make clear their
usage is not tied to BH being disabled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-04-27
This series contains updates to i40e and i40evf.
Alex Duyck cleans up the feature flags since they are becoming pretty
"massive", the primary change being that we now build our features list
around hw_encap_features. Added support for IPIP and SIT offloads,
which should improvement in throughput for IPIP and SIT tunnels with
the offload enabled.
Mitch adds support for configuring RSS on behalf of the VFs, which removes
the burden of dealing with different hardware interfaces from the VF
drivers and improves future compatibility. Fix to ensure that we do not
panic by checking that the vsi_res pointer is valid before dereferencing
it, after which we can drink beer and eat peanuts.
Shannon does come housekeeping in i40e_add_fdir_ethtool() in preparation
for more cloud filter work. Added flexibility to the nvmupdate
facility by adding the ability to specify an AQ event opcode to wait on
after Exec_AQ request.
Michal adds device capability which defines if an update is available and
if a security check is needed during the update process.
Kamil just adds a device id to support X722 QSFP+ device.
Greg fixes an issue where a mirror rule ID may be zero, so do not return
invalid parameter when the user passes in a zero for a rule ID. Adds
support to steer packets to VSIs by VLAN tag alone while being in
promiscuous mode for multicast and unicast MAC addresses.
Jesse fixes the driver from offloading the VLAN tag into the skb any
time there was a VLAN tag and the hardware stripping was enabled, to
making sure it is enabled before put_tag.
v2: Dropped patch 8 ("i40e: Allow user to change input set mask for flow
director") while Kiran reworks a more generalized solution based
on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sd->input_queue_head is incremented for each processed packet
in process_backlog(), and read from other cpus performing
Out Of Order avoidance in get_rps_cpu()
Moving this field in a separate cache line keeps it mostly
hot for the cpu in process_backlog(), as other cpus will
only read it.
In a stress test, process_backlog() was consuming 6.80 % of cpu cycles,
and the patch reduced the cost to 0.65 %
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for W5500 chip.
W5500 has similar register and memory organization with W5100 and W5200.
There are a few important differences listed below but it is still
possible to share common code with W5100 and W5200.
* W5500 register and memory are organized by multiple blocks. Each one
is selected by 16bits offset address and 5bits block select bits.
But the existing register access operations take u16 address. This change
extends the addess by u32 address and put offset address to lower 16bits
and block select bits to upper 16bits.
This change also adds the offset addresses for socket register and TX/RX
memory blocks to the driver private data structure in order to reduce
conditional switches for each chip.
* W5500 has the different register offset for socket interrupt mask
register. Newly added internal functions w5100_enable_intr() and
w5100_disable_intr() take care of the diffrence.
* W5500 has the different register offset for retry time-value register.
But this register is only used to verify that the reset value is correctly
read at initialization. So move the verification to w5100_hw_reset()
which already does different things for different chips.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sg_dma_len() macro can be used only on scattelists which are mapped, so
all calls to it before dma_map_sg() are invalid. Replace them by proper
check for direct sg segment length read.
Fixes: a49e490c7a ("crypto: s5p-sss - add S5PV210 advanced crypto engine support")
Fixes: 9e4a1100a4 ("crypto: s5p-sss - Handle unaligned buffers")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The pf2vf_resp_wq is a global so it has to be created at init
and destroyed at exit, instead of per device.
Cc: <stable@vger.kernel.org>
Tested-by: Suresh Marikkannu <sureshx.marikkannu@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For platforms which are controlled via remove node manager, enable _PPC by
default. These platforms are mostly categorized as enterprise server or
performance servers. These platforms needs to go through some
certifications tests, which tests control via _PPC.
The relative risk of enabling by default is low as this is is less likely
that these systems have broken _PSS table.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When policy->max is changed via _PPC or sysfs and is more than the max non
turbo frequency, it does not really change resulting performance in some
processors. When policy->max results in a P-State ratio more than the
turbo activation ratio, then processor can choose any P-State up to max
turbo. So the user or _PPC setting has no value, but this can cause
undesirable side effects like:
- Showing reduced max percentage in Intel P-State sysfs
- It can cause reduced max performance under certain boundary conditions:
The requested max scaling frequency either via _PPC or via cpufreq-sysfs,
will be converted into a fixed floating point max percent scale. In
majority of the cases this will result in correct max. But not 100% of the
time. If the _PPC is requested at a point where the calculation lead to a
lower max, this can result in a lower P-State then expected and it will
impact performance.
Example of this condition using a Broadwell laptop with config TDP.
ACPI _PSS table from a Broadwell laptop
2301000 2300000 2200000 2000000 1900000 1800000 1700000 1500000 1400000
1300000 1100000 1000000 900000 800000 600000 500000
The actual results by disabling config TDP so that we can get what is
requested on or below 2300000Khz.
scaling_max_freq Max Requested P-State Resultant scaling
max
---------------------------------------- ----------------------
2400000 18 2900000 (max
turbo)
2300000 17 2300000 (max
physical non turbo)
2200000 15 21000002100000 15 2100000
2000000 13 1900000
1900000 13 1900000
1800000 12 1800000
1700000 11 1700000
1600000 10 1600000
1500000 f 1500000
1400000 e 1400000
1300000 d 1300000
1200000 c 1200000
1100000 a 1000000
1000000 a 1000000
900000 9 900000
800000 8 800000
700000 7 700000
600000 6 600000
500000 5 500000
------------------------------------------------------------------
Now set the config TDP level 1 ratio as 0x0b (equivalent to 1100000KHz)
in BIOS (not every system will let you adjust this).
The turbo activation ratio will be set to one less than that, which will
be 0x0a (So any request above 1000000KHz should result in turbo region
assuming no thermal limits).
Here _PPC will request max to 1100000KHz (which basically should still
result in turbo as this is more than the turbo activation ratio up to
max allowable turbo frequency), but actual calculation resulted in a max
ceiling P-State which is 0x0a. So under any load condition, this driver
will not request turbo P-States. This will be a huge performance hit.
When config TDP feature is ON, if the _PPC points to a frequency above
turbo activation ratio, the performance can still reach max turbo. In this
case we don't need to treat this as the reduced frequency in set_policy
callback.
In this change when config TDP is active (by checking if the physical max
non turbo ratio is more than the current max non turbo ratio), any request
above current max non turbo is treated as full performance.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw : Minor cleanups ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use ACPI _PPC notification to limit max P state driver will request.
ACPI _PPC change notification is sent by BIOS to limit max P state
in several cases:
- Reduce impact of platform thermal condition
- When Config TDP feature is used, a changed _PPC is sent to
follow TDP change
- Remote node managers in server want to control platform power
via baseboard management controller (BMC)
This change registers with ACPI processor performance lib so that
_PPC changes are notified to cpufreq core, which in turns will
result in call to .setpolicy() callback. Also the way _PSS
table identifies a turbo frequency is not compatible to max turbo
frequency in intel_pstate, so the very first entry in _PSS needs
to be adjusted.
This feature can be turned on by using kernel parameters:
intel_pstate=support_acpi_ppc
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor cleanups ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Power allocator's parameters are S32 type, so use %d to print them.
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When calculate temperature, old code firstly do division and then
convert to "millicelsius" unit. This will lose resolution and only can
read back temperature with "Celsius" unit.
So firstly scale step value to "millicelsius" and then do division, so
finally we can increase resolution for temperature value. Also refine
the calculation from temperature value to step value.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The MIC VOP driver does two successive reads from user space to read a
variable length data structure. Kernel memory corruption can result if
the data structure changes between the two reads. This patch disallows
the chance of this happening.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116651
Reported by: Pengfei Wang <wpengfeinudt@gmail.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIC VOP driver does two successive reads from user space to read a
variable length data structure. Kernel memory corruption can result if
the data structure changes between the two reads. This patch disallows
the chance of this happening.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116651
Reported by: Pengfei Wang <wpengfeinudt@gmail.com>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The secondary CPU starts up in ARM mode. When the kernel is compiled in
thumb2 mode we have to explicitly compile the secondary startup
trampoline in ARM mode, otherwise the CPU will go to Nirvana.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The frequency transition latency from pmin to pmax is observed to be in
few millisecond granurality. And it usually happens to take a performance
penalty during sudden frequency rampup requests.
This patch set solves this problem by using an entity called "global
pstates". The global pstate is a Chip-level entity, so the global entitiy
(Voltage) is managed across the cores. The local pstate is a Core-level
entity, so the local entity (frequency) is managed across threads.
This patch brings down global pstate at a slower rate than the local
pstate. Hence by holding global pstates higher than local pstate makes
the subsequent rampups faster.
A per policy structure is maintained to keep track of the global and
local pstate changes. The global pstate is brought down using a parabolic
equation. The ramp down time to pmin is set to ~5 seconds. To make sure
that the global pstates are dropped at regular interval , a timer is
queued for every 2 seconds during ramp-down phase, which eventually brings
the pstate down to local pstate.
Iozone results show fairly consistent performance boost.
YCSB on redis shows improved Max latencies in most cases.
Iozone write/rewite test were made with filesizes 200704Kb and 401408Kb
with different record sizes . The following table shows IOoperations/sec
with and without patch.
Iozone Results ( in op/sec) ( mean over 3 iterations )
---------------------------------------------------------------------
file size- with without %
recordsize-IOtype patch patch change
----------------------------------------------------------------------
200704-1-SeqWrite 1616532 1615425 0.06
200704-1-Rewrite 2423195 2303130 5.21
200704-2-SeqWrite 1628577 1602620 1.61
200704-2-Rewrite 2428264 2312154 5.02
200704-4-SeqWrite 1617605 1617182 0.02
200704-4-Rewrite 2430524 2351238 3.37
200704-8-SeqWrite 1629478 1600436 1.81
200704-8-Rewrite 2415308 2298136 5.09
200704-16-SeqWrite 1619632 1618250 0.08
200704-16-Rewrite 2396650 2352591 1.87
200704-32-SeqWrite 1632544 1598083 2.15
200704-32-Rewrite 2425119 2329743 4.09
200704-64-SeqWrite 1617812 1617235 0.03
200704-64-Rewrite 2402021 2321080 3.48
200704-128-SeqWrite 1631998 1600256 1.98
200704-128-Rewrite 2422389 2304954 5.09
200704-256 SeqWrite 1617065 1616962 0.00
200704-256-Rewrite 2432539 2301980 5.67
200704-512-SeqWrite 1632599 1598656 2.12
200704-512-Rewrite 2429270 2323676 4.54
200704-1024-SeqWrite 1618758 1616156 0.16
200704-1024-Rewrite 2431631 2315889 4.99
401408-1-SeqWrite 1631479 1608132 1.45
401408-1-Rewrite 2501550 2459409 1.71
401408-2-SeqWrite 1617095 1626069 -0.55
401408-2-Rewrite 2507557 2443621 2.61
401408-4-SeqWrite 1629601 1611869 1.10
401408-4-Rewrite 2505909 2462098 1.77
401408-8-SeqWrite 1617110 1626968 -0.60
401408-8-Rewrite 2512244 2456827 2.25
401408-16-SeqWrite 1632609 1609603 1.42
401408-16-Rewrite 2500792 2451405 2.01
401408-32-SeqWrite 1619294 1628167 -0.54
401408-32-Rewrite 2510115 2451292 2.39
401408-64-SeqWrite 1632709 1603746 1.80
401408-64-Rewrite 2506692 2433186 3.02
401408-128-SeqWrite 1619284 1627461 -0.50
401408-128-Rewrite 2518698 2453361 2.66
401408-256-SeqWrite 1634022 1610681 1.44
401408-256-Rewrite 2509987 2446328 2.60
401408-512-SeqWrite 1617524 1628016 -0.64
401408-512-Rewrite 2504409 2442899 2.51
401408-1024-SeqWrite 1629812 1611566 1.13
401408-1024-Rewrite 2507620 2442968 2.64
Tested with YCSB workload (50% update + 50% read) over redis for 1 million
records and 1 million operation. Each test was carried out with target
operations per second and persistence disabled.
Max-latency (in us)( mean over 5 iterations )
---------------------------------------------------------------
op/s Operation with patch without patch %change
---------------------------------------------------------------
15000 Read 61480.6 50261.4 22.32
15000 cleanup 215.2 293.6 -26.70
15000 update 25666.2 25163.8 2.00
25000 Read 32626.2 89525.4 -63.56
25000 cleanup 292.2 263.0 11.10
25000 update 32293.4 90255.0 -64.22
35000 Read 34783.0 33119.0 5.02
35000 cleanup 321.2 395.8 -18.8
35000 update 36047.0 38747.8 -6.97
40000 Read 38562.2 42357.4 -8.96
40000 cleanup 371.8 384.6 -3.33
40000 update 27861.4 41547.8 -32.94
45000 Read 42271.0 88120.6 -52.03
45000 cleanup 263.6 383.0 -31.17
45000 update 29755.8 81359.0 -63.43
(test without target op/s)
47659 Read 83061.4 136440.6 -39.12
47659 cleanup 195.8 193.8 1.03
47659 update 73429.4 124971.8 -41.24
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 1b0289848d ("cpufreq: powernv: Add sysfs attributes to show
throttle stats") used policy->driver_data as a flag for one-time creation
of throttle sysfs files. Instead of this use 'kernfs_find_and_get()' to
check if the attribute already exists. This is required as
policy->driver_data is used for other purposes in the later patch.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove redundant duplicate const, which is found by smatch:
arch/arm/mach-lpc32xx/phy3250.c:162:42: warning: duplicate const
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching the platform to common clock framework there is no
more need to keep dead code in arch/arm/mach-lpc32xx, which glued
legacy clock source and clock provider drivers, remove the leftovers.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The header file "reboot.h" is no longer needed, following
the migration of the restart code into the pnx4008 watchdog.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To declare MTD OF partitions NAND controller device node should have
a special 'partitions' subnode, the change removes a debug message
from mtd/ofpart on boot:
nxp_lpc3220_slc: 'partitions' subnode not found on /ahb/flash@20020000.
Trying to parse direct subnodes as partitions.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change simplifies layout of PHY3250 board description by
referencing device nodes of LPC32xx controllers by label.
No functional change intended.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
