We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sort IDs in groups to be easily found when needed.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems there are leftovers of some assignments which are not used
anymore. Compiler even warns us about:
drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]
Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
While here, convert PM ops to use modern API.
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch changes SROM nodes compatible from generic to model specific
to match with binding documentation. Also updating property
"samsung,srom-page-mode" as it is not defined as bool instead of int
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fix a typo causing a build regression.
Fixes: f90c6bdb69 ("gpio: f7188x: use the new open drain callback")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use recently introduced flag LED_HW_PLUGGABLE to avoid warnings when
the device is unplugged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix Section mismatch warinig in adf_exit_vf_wq()
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
IRQs need to be enabled when VFs go down in case some VF to PF
comms happens.
Tested-by: Suman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Before VF sends a signal to PF it should check if PF
is still running.
Tested-by: Suman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The vf2pf_init and vf2pf_exit are exactly the same for all VFs
so move them to common and reuse.
Tested-by: Suman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874ed ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We need to update the user TM feature bits (PPC_FEATURE2_HTM and
PPC_FEATURE2_HTM) to mirror what we do with the kernel TM feature
bit.
At the moment, if firmware reports TM is not available we turn off
the kernel TM feature bit but leave the userspace ones on. Userspace
thinks it can execute TM instructions and it dies trying.
This (together with a QEMU patch) fixes PR KVM, which doesn't currently
support TM.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
scan_features() updates cpu_user_features but not cpu_user_features2.
Amongst other things, cpu_user_features2 contains the user TM feature
bits which we must keep in sync with the kernel TM feature bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The REAL_LE feature entry in the ibm_pa_feature struct is missing an MMU
feature value, meaning all the remaining elements initialise the wrong
values.
This means instead of checking for byte 5, bit 0, we check for byte 0,
bit 0, and then we incorrectly set the CPU feature bit as well as MMU
feature bit 1 and CPU user feature bits 0 and 2 (5).
Checking byte 0 bit 0 (IBM numbering), means we're looking at the
"Memory Management Unit (MMU)" feature - ie. does the CPU have an MMU.
In practice that bit is set on all platforms which have the property.
This means we set CPU_FTR_REAL_LE always. In practice that seems not to
matter because all the modern cpus which have this property also
implement REAL_LE, and we've never needed to disable it.
We're also incorrectly setting MMU feature bit 1, which is:
#define MMU_FTR_TYPE_8xx 0x00000002
Luckily the only place that looks for MMU_FTR_TYPE_8xx is in Book3E
code, which can't run on the same cpus as scan_features(). So this also
doesn't matter in practice.
Finally in the CPU user feature mask, we're setting bits 0 and 2. Bit 2
is not currently used, and bit 0 is:
#define PPC_FEATURE_PPC_LE 0x00000001
Which says the CPU supports the old style "PPC Little Endian" mode.
Again this should be harmless in practice as no 64-bit CPUs implement
that mode.
Fix the code by adding the missing initialisation of the MMU feature.
Also add a comment marking CPU user feature bit 2 (0x4) as reserved. It
would be unsafe to start using it as old kernels incorrectly set it.
Fixes: 44ae3ab335 ("powerpc: Free up some CPU feature bits by moving out MMU-related features")
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
[mpe: Flesh out changelog, add comment reserving 0x4]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I had a thinko in spmi_regulator_select_voltage_same_range() when
converting it to return selectors via the function's return value
instead of by modifying a pointer argument. I only tested
multi-range regulators so this passed through testing. Fix it by
returning the selector here.
Fixes: 1b5b196892 ("regulator: qcom_spmi: Only use selector based regulator ops")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, player#0 is connected to I2S/TDM TX bus.
This patch connects player#1 to I2S/TDM TX bus.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added runtime PM support for the cadence spi driver
causes harmless warnings when PM is disabled:
drivers/spi/spi-cadence.c:681:12: warning: 'cnds_runtime_suspend' defined but not used
drivers/spi/spi-cadence.c:652:12: warning: 'cnds_runtime_resume' defined but not used
This adds __maybe_unused annotations to the respective functions
to shut up the warnings, while leaving the code in place for
compile testing and avoiding ugly #ifdefs.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Optiplex 9020m with Haswell-DT processor needs a quirk for the
headset jack at the front of the machine to be able to use microphones.
A quirk for this model was originally added in 3127899, but c77900e
removed it in favour of a more generic version.
Unfortunately, pin configurations can changed based on firmware/BIOS
versions, and the generic version doesn't have any effect on newer
versions of the machine/firmware anymore.
With help from David Henningsson <diwic@ubuntu.com>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For reasons unknown Sandybridge GT1 (at least) will eventually hang when
it encounters a ring wraparound at offset 0. The test case that
reproduces the bug reliably forces a large number of interrupted context
switches, thereby causing very frequent ring wraparounds, but there are
similar bug reports in the wild with the same symptoms, seqno writes
stop just before the wrap and the ringbuffer at address 0. It is also
timing crucial, but adding various delays hasn't helped pinpoint where
the window lies.
Whether the fault is restricted to the ringbuffer itself or the GTT
addressing is unclear, but moving the ringbuffer fixes all the hangs I
have been able to reproduce.
References: (e.g.) https://bugs.freedesktop.org/show_bug.cgi?id=93262
Testcase: igt/gem_exec_whisper/render-contexts-interruptible #snb-gt1
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460565315-7748-12-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit a687a43a48)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We started to use PIPE_CONTROL to write render ring seqno in order to
combat seqno write vs interrupt generation problems. This was introduced
by commit 7c17d37737 ("drm/i915: Use ordered seqno write interrupt
generation on gen8+ execlists").
On gen8+ size of PIPE_CONTROL with Post Sync Operation should be
6 dwords. When we're using older 5-dword variant it's possible to
observe inconsistent values written by PIPE_CONTROL with Post
Sync Operation from user batches, resulting in rendering corruptions.
v2: Fix BAT failures
v3: Comments on alignment and thrashing high dword of seqno (Chris)
v4: Updated commit msg (Mika)
Testcase: igt/gem_pipe_control_store_loop/*-qword-write
Issue: VIZ-7393
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460469115-26002-1-git-send-email-michal.winiarski@intel.com
(cherry picked from commit ce81a65c79)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Experiments with heaven 4.0 benchmark and skylake gt3e (rev 0xa)
suggest that WaForceContextSaveRestoreNonCoherent is needed for all
revs. Extending this to all revs cures a gpu hang with rev 0xa when
running heaven4.0 gpu benchmark.
We have been here before, with problems enabling gt4e and extending
up to revision F0 instead of false claims of bspec of E0 only. See
commit <e238659ddd> ("drm/i915/skl: Default to noncoherent access
up to F0"). In retrospect we should have covered this with this big
blanket back then already, as E0 vs F0 discrepancy was suspicious
enough.
Previously the WaForceEnableNonCoherent has been tied to
context non-coherence, atleast in relevant hsds. So keep this tie
and extended this alongside.
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: stable@vger.kernel.org
Reported-by: Mike Lothian <mike@fireburn.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93491
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 97ea6be161)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For all gt3 and gt4 skylake variants, extend the usage of
WaRsDisableCoarsePowerGating for all revisions. Without this
gt3 and gt4 skylakes up to atleast rev 0xa can gpu hang or
system hang.
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: <stable@vger.kernel.org>
Reported-by: Mikael Djurfeldt <mikael@djurfeldt.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=94161
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 185c66e57c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.
Testcase: igt/gem_shrink/*userptr
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 40313f0cd0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
