Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These conditions can happen any time VFs are enabled or disabled and are
not really indicative of fatal problems unless they happen continuously.
Lower the log level so that people don't get scared.
Change-ID: I1ceb4adbd10d03cbeed54d1f5b7f20d60328351d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
100baseT/Full is now listed and supported link mode for 10GBaseT PHY.
This is a fix to list all the supported link modes of 10GBaseT PHY.
Change-ID: If2be3212ef0fef85fd5d6e4550c7783de2f915e9
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were passing in the seed where we should just be passing false
because we want the VSI table not the pf table.
Change-ID: I9b633ab06eb59468087f0c0af8539857e99f9495
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Upon module remove, wait a little longer after requesting a reset before
checking to see if the firmware responded. This change prevents double
resets when the firmware is busy.
Change-ID: Ieedc988ee82fac1f32a074bf4d9e4dba426bfa58
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit immediately after triggering a reset instead of
waiting until after cleanup is complete. Make sure to trigger a reset
every time, not just if the PF is up.
These changes fix a problem where VF resets would get lost by the PF,
preventing the VF driver from initializing.
Change-ID: I5945cf2884095b7b0554867c64df8617e71d9d29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new device ID is 0x37D3 and it should follow the same flows and
branding string as for 0x37D0.
Change-ID: Ia5ad4a1910268c4666a3fd46a7afffbec55b4fc2
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Users of ethtool were being given the mistaken impression that this
driver was able to change its VLAN tagging features, and were
disappointed that this was not actually the case. Implement
ndo_fix_features method so that we can adjust these flags as needed to
avoid false impressions.
Change-ID: I08584f103a4fa73d6a4128d472e4ef44dcfda57f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This variable is vestigial, a remnant of the primordial code from which
this driver spawned. We can safely remove it.
Change-ID: I24e0fe338e7c7c50d27dc5515564f33caefbb93a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the Capability for XL710/X710 devices with FW API
version higher than 1.4 to do geneve Rx offload.
Change-ID: I9a8f87772c48d7d67dc85e3701d2e0b845034c0b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
active_vlans is an unsigned long array, hence a null check on this
array is superfluous and can be removed.
Detected with static analysis by smatch:
drivers/net/ethernet/intel/i40e/i40e_debugfs.c:386
i40e_dbg_dump_vsi_seid() warn: this array is probably
non-NULL. 'vsi->active_vlans'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When signaling that a GRO frame is ready to be processed, the network stack
correctly checks length and aborts processing when a frame is less than 14
bytes. However, such a condition is really indicative of a broken driver,
and should be loudly signaled, rather than silently dropped as the case is
today.
Convert the condition to use net_warn_ratelimited() to ensure the stack
loudly complains about such broken drivers.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
The current OF translation of channels can never work with
any DMA client using the DMA channels directly: the only way
to get the channels initialized properly is in the
dma_async_device_register() call, where chan->dev etc is
allocated and initialized.
Allocate and initialize all possible DMA channels and
only augment a target channel with the periph_buses at
of_xlate(). Remove some const settings to make things work.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Enable RX Checksum offload feature in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VNIC driver to provide descriptors containing
L2/L3/L4 headers to firmware. This feature is needed
for greater hardware compatibility and enablement of checksum
and TCP offloading features.
A new function is included for the hypervisor call,
H_SEND_SUBCRQ_INDIRECT, allowing a DMA-mapped array of SCRQ
descriptor elements to be sent to the VNIC server.
These additions will help fully enable checksum offloading as
well as other features as they are included later.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Check whether plane parameters comply with IPU IDMAC limitations and
fix planar YUV 4:2:0 U/V offsets and stride
- Cleanup encoder in dw_hdmi-imx bind error path and
remove a superfluous platform_set_drvdata in dw_hdmi-imx
- DMFC setup fixes: lock the ipu_dmfc_init_channel function against
concurrent use, rename it to ipu_dmfc_config_wait4eot, and call
it after the FIFO size has been determined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW/hz5AAoJEFDCiBxwnmDr3r8P/1sjFlMvUICcOby94XA2B3tg
YxJg0O8M6sPdWHb44c1r77nwSc81788UaYr1YzyHmYrk/zicbEyM3+vm5W9t4Zsu
89nJ06AWPKm6N+nWCNBeOrCJ7j720snq1Kop6s+Ylf/7x3VvPVGoDM0MuTMu6qPL
XagVPBvyaCqMiLihYYBhAUg35eUP3i4Jlo7wbI2VQzpKjYECqOhrd8zVrjzR4P9/
T2LaGLjVxytjBXGHl2evVJbJOSdFFjWgyUgYQe2hTg0SGxQsbEvPGHHNrG8QvtTG
0uOL9yCSrHEjgotZME7rnZywaCWaHW5H7G+Rz8HRAjIhvkmpAI84vWLK6ULOdkrG
Kg36GuEoeuO09E82U3Rs03vKePQjHxvvInkRFRWPwZpQFm0AMq10pqCC5qcvDB/E
ZDLTRGhgrcobDDCfZ7OZ03daz1pwFKuBwRpF/aIDnsXiI6iszNr9luKOlUDOiSEG
qd2T7Msq1HcL0sGDSdYhibrwYzduUkkKZYSoT2Bet5FAjQt/nK9h/x5jl7ypm4Hb
sMy4eQRRoPyl6JtHVfnVE6rg1nYhs/PEC1A8dVSoNaVcw8tXHkI8J92HsarrGeKO
ld3sRdcJ1VACqvpLIGIzXn+2U+BmOFmUjYcelBFi2yWTvZFNOV18LbC5pRJAqZ2S
XFFQiHyG0HpuTDViYzp2
=3/Gi
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-04-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: stricter plane parameter checking, dw_hdmi-imx and dmfc fixes
- Check whether plane parameters comply with IPU IDMAC limitations and
fix planar YUV 4:2:0 U/V offsets and stride
- Cleanup encoder in dw_hdmi-imx bind error path and
remove a superfluous platform_set_drvdata in dw_hdmi-imx
- DMFC setup fixes: lock the ipu_dmfc_init_channel function against
concurrent use, rename it to ipu_dmfc_config_wait4eot, and call
it after the FIFO size has been determined.
* tag 'imx-drm-next-2016-04-01' of git://git.pengutronix.de/git/pza/linux:
drm/imx: Don't set a gamma table size
drm/imx: ipuv3-plane: Configure DMFC wait4eot bit after slots are determined
gpu: ipu-v3: ipu-dmfc: Rename ipu_dmfc_init_channel to ipu_dmfc_config_wait4eot
gpu: ipu-v3: ipu-dmfc: Make function ipu_dmfc_init_channel() return void
gpu: ipu-v3: ipu-dmfc: Protect function ipu_dmfc_init_channel() with mutex
drm/imx: dw_hdmi: Don't call platform_set_drvdata()
drm/imx: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/imx: ipuv3-plane: fix planar YUV 4:2:0 support
drm/imx: ipuv3-plane: Add more thorough checks for plane parameter limitations
gpu: ipu-cpmem: modify ipu_cpmem_set_yuv_planar_full for better control
When creating an ip6tnl tunnel with ip tunnel, rtnl_link_ops is not set
before ip6_tnl_create2 is called. When register_netdevice is called, there
is no linkinfo attribute in the NEWLINK message because of that.
Setting rtnl_link_ops before calling register_netdevice fixes that.
Fixes: 0b11245722 ("ip6tnl: add support of link creation via rtnl")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These three warnings are fixed:
fs/xfs/xfs_inode.c:1033:44: warning: Using plain integer as NULL pointer
fs/xfs/xfs_inode_item.c:525:20: warning: context imbalance in 'xfs_inode_item_push' - unexpected unlock
fs/xfs/xfs_dquot.c:696:1: warning: symbol 'xfs_dq_get_next_id' was not declared. Should it be static?
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Use krealloc to implement our realloc function. This helps to avoid
new allocations if we are still in the slab bucket. At least for the
bmap btree root that's actually the common case.
This also allows removing the now unused oldsize argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
I had sent this patch yesterday, but for some reason it didn't reach
xfs list, sending again.
Output the caller of xfs_log_force might be useful when tracing log
checkpoint problems without the need to build kernel with DEBUG.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
- VBT code refactor for a clean split between parsing&using of firmware
information (Jani)
- untangle the pll computation code, and splitting up the monster
i9xx_crtc_compute_clocks (Ander)
- dsi support for bxt (Jani, Shashank Sharma and others)
- color manager (i.e. de-gamma, color conversion matrix & gamma support) from
Lionel Landwerlin
- Vulkan hsw support in the command parser (Jordan Justen)
- large-scale renaming of intel_engine_cs variables/parameters to avoid the epic
ring vs. engine confusion introduced in gen8 (Tvrtko Ursulin)
- few atomic patches from Maarten&Matt, big one is two-stage wm programming on ilk-bdw
- refactor driver load and add infrastructure to inject load failures for
testing, from Imre
- various small things all over
* tag 'drm-intel-next-2016-03-30' of git://anongit.freedesktop.org/drm-intel: (179 commits)
drm/i915: Update DRIVER_DATE to 20160330
drm/i915: Call intel_dp_mst_resume() before resuming displays
drm/i915: Fix races on fbdev
drm/i915: remove unused dev_priv->render_reclock_avail
drm/i915: move sdvo mappings to vbt data
drm/i915: move edp low vswing config to vbt data
drm/i915: use a substruct in vbt data for edp
drm/i915: replace for_each_engine()
drm/i915: introduce for_each_engine_id()
drm/i915/bxt: Fix DSI HW state readout
drm/i915: Remove vblank wait from hsw_enable_ips, v2.
drm/i915: Tidy aliasing_gtt_bind_vma()
drm/i915: Split PNV version of crtc_compute_clock()
drm/i915: Split g4x_crtc_compute_clock()
drm/i915: Split i8xx_crtc_compute_clock()
drm/i915: Split CHV and VLV specific crtc_compute_clock() hooks
drm/i915: Merge ironlake_compute_clocks() and ironlake_crtc_compute_clock()
drm/i915: Move fp divisor calculation into ironlake_compute_dpll()
drm/i915: Pass crtc_state->dpll directly to ->find_dpll()
drm/i915: Simplify ironlake_crtc_compute_clock() CPU eDP case
...
This reverts commit 543e3a8da5.
Direct callers of __netpoll_setup() depend on it to set np->dev,
so we can't simply move that assignment up to netpoll_stup().
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther says:
====================
bcmgenet cleanups
Three cleanup patches for bcmgenet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dmadesc_set() is used for setting the Tx buffer DMA address, length,
and status bits on a Tx ring descriptor when a frame is being Tx'ed.
Always set the Tx buffer DMA address first, before updating the length
and status bits, i.e. giving the Tx descriptor to the hardware.
The reason this is a cleanup rather than a fix is that the hardware
won't transmit anything from a Tx ring until the TDMA producer index
has been incremented. As long as the dmadesc_set() writes complete
before the TDMA producer index write, life is good.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add frag_size = skb_frag_size(frag) and use it when needed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Readability: Move nr_frags assignment a few lines down in order
to bundle index -> ring -> txq calculations together.
2. Readability: Add parentheses around nr_frags + 1.
3. Minor fix: Stop the Tx queue and throw the error message only if
the Tx queue hasn't already been stopped.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to i40e and e1000.
Jesse fixes an issue where code was added by a previous commit but the
flag to enable it was never set.
Alex fixes the e1000 driver from grossly overestimated the descriptors
needed to transmit a frame.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These aren't used for CIL-style logging and can be dropped.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Merge xfs_trans_reserve and xfs_trans_alloc into a single function call
that returns a transaction with all the required log and block reservations,
and which allows passing transaction flags directly to avoid the cumbersome
_xfs_trans_alloc interface.
While we're at it we also get rid of the transaction type argument that has
been superflous since we stopped supporting the non-CIL logging mode. The
guts of it will be removed in another patch.
[dchinner: fixed transaction leak in error path in xfs_setattr_nonsize]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
others are usual stable material.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXA8x6AAoJEL/70l94x66D0x8H/RcBnc75994RQ++WmHSvD9GF
yruGB8soLDdjX+Oceol0aEPHokrBu3JtcdoTBe0GwbCKV/F5NkQZ4EfLxDtR3tte
7ILkPULLy5GElFpJNQuT4pmXzTEspFvXpqHhFik7WVBga3W9wMFQcjbrgmGBUzLE
p2aJVhZyErpKxGFkUYWhDnlqWsguTTIzv/pqNhLY4VVc0UrXN9AA0fq9RkvgU3KS
Hxk4/A6SV/b7dyzvttzITww0f1iu8FmlLj2TXapIEoOz7AnInD6KIN0RYpxbDjxN
bEzEfpahUtuDeM87/t2kHEj0Gn09iHK7/BbCC1Hrwo1CQhbAQ/D0GIvqYAQixf4=
=NugZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Miscellaneous bugfixes.
The ARM and s390 fixes are for new regressions from the merge window,
others are usual stable material"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
compiler-gcc: disable -ftracer for __noclone functions
kvm: x86: make lapic hrtimer pinned
s390/mm/kvm: fix mis-merge in gmap handling
kvm: set page dirty only if page has been writable
KVM: x86: reduce default value of halt_poll_ns parameter
KVM: Hyper-V: do not do hypercall userspace exits if SynIC is disabled
KVM: x86: Inject pending interrupt even if pending nmi exist
arm64: KVM: Register CPU notifiers when the kernel runs at HYP
arm64: kvm: 4.6-rc1: Fix VTCR_EL2 VS setting
This patch implements two closely related changes: First it embeds
a bio the ioend structure so that we don't have to allocate one
separately. Second it uses the block layer bio chaining mechanism
to chain additional bios off this first one if needed instead of
manually accounting for multiple bio completions in the ioend
structure. Together this removes a memory allocation per ioend and
greatly simplifies the ioend setup and I/O completion path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
dma_get_slave_caps() API only checked for slave capability where
we use slave capabilities for cyclic dma operations as well, so we
should add the cyclic case here too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Completion of an ioend requires us to walk the bufferhead list to
end writback on all the bufferheads. This, in turn, is needed so
that we can end writeback on all the pages we just did IO on.
To remove our dependency on bufferheads in writeback, we need to
turn this around the other way - we need to walk the pages we've
just completed IO on, and then walk the buffers attached to the
pages and complete their IO. In doing this, we remove the
requirement for the ioend to track bufferheads directly.
To enable IO completion to walk all the pages we've submitted IO on,
we need to keep the bios that we used for IO around until the ioend
has been completed. We can do this simply by chaining the bios to
the ioend at completion time, and then walking their pages directly
just before destroying the ioend.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[hch: changed the xfs_finish_page_writeback calling convention]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Currently adding a buffer to the ioend and then building a bio from
the buffer list are two separate operations. We don't build the bios
and submit them until the ioend is submitted, and this places a
fixed dependency on bufferhead chaining in the ioend.
The first step to removing the bufferhead chaining in the ioend is
on the IO submission side. We can build the bio directly as we add
the buffers to the ioend chain, thereby removing the need for a
latter "buffer-to-bio" submission loop. This allows us to submit
bios on large ioends as soon as we cannot add more data to the bio.
These bios then get captured by the active plug, and hence will be
dispatched as soon as either the plug overflows or we schedule away
from the writeback context. This will reduce submission latency for
large IOs, but will also allow more timely request queue based
writeback blocking when the device becomes congested.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[hch: various small updates]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The 82544 has code that adds one additional descriptor per data buffer.
However we weren't taking that into account when determining the descriptors
needed for the next transmit at the end of the xmit_frame path.
This change takes that into account by doubling the number of descriptors
needed for the 82544 so that we can avoid a potential issue where we could
hang the Tx ring by loading frames with xmit_more enabled and then stopping
the ring without writing the tail.
In addition it adds a few more descriptors to account for some additional
workarounds that have been added over time.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
dw_pcie_host_init() looks up host bridge resources, ioremaps them, creates
IRQ domains, and enumerates devices below the bridge. dw_pcie_setup_rc()
programs the Root Complex registers. The Root Complex may lose power
during suspend-to-RAM, and when we resume, we want to redo the latter but
not the former.
Move some Root Complex programming from dw_pcie_host_init() to
dw_pcie_setup_rc() where it belongs. DesignWare-based drivers can call
dw_pcie_setup_rc() in their resume paths.
[Niklas Cassel <niklas.cassel@axis.com>: This change moves outbound ATU
programming, which uses pp->mem_base, to dw_pcie_setup_rc(). Apply the
dra7xx pp->mem_base update before calling dw_pcie_setup_rc().]
[bhelgaas: changelog, fold in dra7xx fix from Niklas]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The current code path is capable of grossly overestimating the number of
descriptors needed to transmit a new frame. This specifically occurs if
the skb contains a number of 4K pages. The issue is that the logic for
determining the descriptors needed is ((S) >> (X)) + 1. When X is 12 it
means that we were indicating that we required 2 descriptors for each 4K
page when we only needed one.
This change corrects this by instead adding (1 << (X)) - 1 to the S value
instead of adding 1 after the fact. This way we get an accurate descriptor
needed count as we are essentially doing a DIV_ROUNDUP().
Reported-by: Ivan Suzdal <isuzdal@mirantis.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Consolidate the 2 calls to ->put_listent in
xfs_attr3_leaf_list_int(), by setting up name, namelen, and
valuelen for the local vs remote cases, then call ->put_listent
and do the error handling all in one spot.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
The put_value context member is never set; remove it
and the conditional test in xfs_attr3_leaf_list_int().
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The value is not used; only names and value lengths are
returned. Remove the argument.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Today, the put_listent formatters return either 1 or 0; if
they return 1, some callers treat this as an error and return
it up the stack, despite "1" not being a valid (negative)
error code.
The intent seems to be that if the input buffer is full,
we set seen_enough or set count = -1, and return 1;
but some callers check the return before checking the
seen_enough or count fields of the context.
Fix this by only returning non-zero for actual errors
encountered, and rely on the caller to first check the
return value, then check the values in the context to
decide what to do.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
By overallocating the in-core inode fork data buffer and zero
terminating the link target in xfs_init_local_fork we can avoid
the memory allocation in ->follow_link.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
There was an error introduced with commit 3fced53507 ("i40e: X722 is
on the IOSF bus and does not report the PCI bus info"), where code was
added but the enabling flag is never set.
CC: Anjali Singhai Jain <anjali.singhai@intel.com>
CC: Stefan Assman <sassman@redhat.com>
Fixes: 3fced53507 ("i40e: X722 is on the IOSF bus ...")
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also drop the now unused readlink_copy export.
[dchinner: use d_inode(dentry) rather than dentry->d_inode]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
In the next patch we'll set up different inode operations for inline vs
out of line symlinks, for that we need to make sure the flags are already
set up properly.
[dchinner: added xfs_setup_iops() call to xfs_rename_alloc_whiteout()]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
