In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds the missing compatible strings from ci_hdrc_imx.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Redirecting the wakeup of a VCPU from the H_IPI hypercall to
a core running in the host is usually a good idea, most workloads
seemed to benefit. However, in one heavily interrupt-driven SMT1
workload, some regression was observed. This patch adds a kvm_hv
module parameter called h_ipi_redirect to control this feature.
The default value for this tunable is 1 - that is enable the feature.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support to real-mode KVM to search for a core
running in the host partition and send it an IPI message with
VCPU to be woken. This avoids having to switch to the host
partition to complete an H_IPI hypercall when the VCPU which
is the target of the the H_IPI is not loaded (is not running
in the guest).
The patch also includes the support in the IPI handler running
in the host to do the wakeup by calling kvmppc_xics_ipi_action
for the PPC_MSG_RM_HOST_ACTION message.
When a guest is being destroyed, we need to ensure that there
are no pending IPIs waiting to wake up a VCPU before we free
the VCPUs of the guest. This is accomplished by:
- Forces a PPC_MSG_CALL_FUNCTION IPI to be completed by all CPUs
before freeing any VCPUs in kvm_arch_destroy_vm().
- Any PPC_MSG_RM_HOST_ACTION messages must be executed first
before any other PPC_MSG_CALL_FUNCTION messages.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the support for the kick VCPU operation for
kvmppc_host_rm_ops. The kvmppc_xics_ipi_action() function
provides the function to be invoked for a host side operation
when poked by the real mode KVM. This is initiated by KVM by
sending an IPI to any free host core.
KVM real mode must set the rm_action to XICS_RM_KICK_VCPU and
rm_data to point to the VCPU to be woken up before sending the IPI.
Note that we have allocated one kvmppc_host_rm_core structure
per core. The above values need to be set in the structure
corresponding to the core to which the IPI will be sent.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kvmppc_host_rm_ops structure keeps track of which cores are
are in the host by maintaining a bitmask of active/runnable
online CPUs that have not entered the guest. This patch adds
support to manage the bitmask when a CPU is offlined or onlined
in the host.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the core host state in kvmppc_host_rm_ops whenever
the primary thread of the core enters the guest or returns
back.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch defines the data structures to support the setting up
of host side operations while running in real mode in the guest,
and also the functions to allocate and free it.
The operations are for now limited to virtual XICS operations.
Currently, we have only defined one operation in the data
structure:
- Wake up a VCPU sleeping in the host when it
receives a virtual interrupt
The operations are assigned at the core level because PowerKVM
requires that the host run in SMT off mode. For each core,
we will need to manage its state atomically - where the state
is defined by:
1. Is the core running in the host?
2. Is there a Real Mode (RM) operation pending on the host?
Currently, core state is only managed at the whole-core level
even when the system is in split-core mode. This just limits
the number of free or "available" cores in the host to perform
any host-side operations.
The kvmppc_host_rm_core.rm_data allows any data to be passed by
KVM in real mode to the host core along with the operation to
be performed.
The kvmppc_host_rm_ops structure is allocated the very first time
a guest VM is started. Initial core state is also set - all online
cores are in the host. This structure is never deleted, not even
when there are no active guests. However, it needs to be freed
when the module is unloaded because the kvmppc_host_rm_ops_hv
can contain function pointers to kvm-hv.ko functions for the
different supported host operations.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Function to cause an IPI by directly updating the MFFR register
in the XICS. The function is meant for real-mode callers since
they cannot use the smp_ops->cause_ipi function which uses an
ioremapped address.
Normal usage is for the the KVM real mode code to set the IPI message
using smp_muxed_ipi_message_pass and then invoke icp_native_cause_ipi_rm
to cause the actual IPI.
The function requires kvm_hstate.xics_phys to have been initialized
with the physical address of XICS.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_muxed_ipi_message_pass() invokes smp_ops->cause_ipi, which
uses an ioremapped address to access registers on the XICS
interrupt controller to cause the IPI. Because of this real
mode callers cannot call smp_muxed_ipi_message_pass() for IPI
messaging.
This patch creates a separate function smp_muxed_ipi_set_message
just to set the IPI message without the cause_ipi routine.
After calling this function to set the IPI message, real
mode callers must cause the IPI by writing to the XICS registers
directly.
As part of this, we also change smp_muxed_ipi_message_pass
to call smp_muxed_ipi_set_message to set the message instead
of doing it directly inside the routine.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch increases the number of demuxed messages for a
controller with a single ipi to 8 for 64-bit systems.
This is required because we want to use the IPI mechanism
to send messages from a CPU running in KVM real mode in a
guest to a CPU in the host to take some action. Currently,
we only support 4 messages and all 4 are already taken.
Define a fifth message PPC_MSG_RM_HOST_ACTION for this
purpose.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 5b6490def9 ("3c59x: Use setup_timer()") Amitoj
removed add_timer which sets up the epires timer. In this patch
the behavior is restore but it uses mod_timer which is a bit more
compact.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to automatically boot-test this defconfig with
kernelci.org.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Regenerate mxs_defconfig by running:
make mxs_defconfig
- Manually disable EXT2_FS and EXT3_FS
make savedefconfig
mv defconfig arch/arm/configs/mxs_defconfig
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx_src_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Palams extcon IRQs are nested threaded and wired to the Palmas
inerrupt controller. So, this flag is not required for nested irqs
anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged.
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When AIO DIO fails e.g. due to IO error, we must not convert unwritten
extents as that will expose uninitialized data. Handle this case
by clearing unwritten flag from io_end in case of error and thus
preventing extent conversion.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This reverts commit 8ba671efdb.
As reported by kbuild test robot <fengguang.wu@intel.com>:
In file included from arch/arm/boot/dts/mt2701-evb.dts:16:0:
>> arch/arm/boot/dts/mt2701.dtsi:18:28: fatal error: mt2701-pinfunc.h: No such file or directory
#include "mt2701-pinfunc.h"
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Till today, the ucode consisted of two d0 images - regular,
in which the usniffer wasn't enabled, and usniffer, in which the
usniffer logs were enabled.
Lately, the two images were unified, so there is only one d0 image,
in which the usniffer logs are enabled.
Add new TLV capability for supporting the consolidated images
(set 2, bit 13).
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when entering D3 with WOWLAN configured, we enable in the
configuration flags beacon storing, and do not disable beacon
filtering, and do not wake up from a magic packet.
Having both enabled is wrong (should not have both enabled),
and causes problems in the RX queues in the FW, causing
the FW not to recognize the magic packet when it comes.
Disable beacon storing in wowlan configuration.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
X32 ABI takes the 64bit timespec, thus the timer user status ioctl becomes
incompatible with IA32. This results in NOTTY error when the ioctl is
issued.
Meanwhile, this struct in X32 is essentially identical with the one in
X86-64, so we can just bypassing to the existing code for this
specific compat ioctl.
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The timer user status compat ioctl returned the bogus struct used for
64bit architectures instead of the 32bit one. This patch addresses
it to return the proper struct.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous fixes for ctl and PCM, we need a fix for
incompatible X32 ABI regarding the rawmidi: namely, struct
snd_rawmidi_status has the timespec, and the size and the alignment on
X32 differ from IA32.
This patch fixes the incompatible ioctl for X32.
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
X32 ABI uses the 64bit timespec in addition to 64bit alignment of
64bit values. This leads to incompatibilities in some PCM ioctls
involved with snd_pcm_channel_info, snd_pcm_status and
snd_pcm_sync_ptr structs. Fix the PCM compat ABI for these ioctls
like the previous commit for ctl API.
Reported-by: Steven Newbury <steve@snewbury.org.uk>
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The X32 ABI takes the same alignment like x86-64, and this may result
in the incompatible struct size from ia32. Unfortunately, we hit this
in some control ABI: struct snd_ctl_elem_value differs between them
due to the position of 64bit variable array. This ends up with the
unknown ioctl (ENOTTY) error.
The fix is to add the compat entries for the new aligned struct.
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull perf fixes from Thomas Gleixner:
"A rather largish series of 12 patches addressing a maze of race
conditions in the perf core code from Peter Zijlstra"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Robustify task_function_call()
perf: Fix scaling vs. perf_install_in_context()
perf: Fix scaling vs. perf_event_enable()
perf: Fix scaling vs. perf_event_enable_on_exec()
perf: Fix ctx time tracking by introducing EVENT_TIME
perf: Cure event->pending_disable race
perf: Fix race between event install and jump_labels
perf: Fix cloning
perf: Only update context time when active
perf: Allow perf_release() with !event->ctx
perf: Do not double free
perf: Close install vs. exit race
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- Hopefully the last ASM CLAC fixups
- A fix for the Quark family related to the IMR lock which makes
kexec work again
- A off-by-one fix in the MPX code. Ironic, isn't it?
- A fix for X86_PAE which addresses once more an unsigned long vs
phys_addr_t hickup"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mpx: Fix off-by-one comparison with nr_registers
x86/mm: Fix slow_virt_to_phys() for X86_PAE again
x86/entry/compat: Add missing CLAC to entry_INT80_32
x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
x86/platform/intel/quark: Change the kernel's IMR lock bit to false
Pull scheduler fixlet from Thomas Gleixner:
"A trivial printk typo fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix trivial typo in printk() message
Pull irq fixes from Thomas Gleixner:
"Four small fixes for irqchip drivers:
- Add missing low level irq handler initialization on mxs, so
interrupts can acutally be delivered
- Add a missing barrier to the GIC driver
- Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
and a cache flush beyond the actual region"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
irqchip/mxs: Add missing set_handle_irq()
irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
Here is one patch, for the android binder driver, to resolve a reported
problem. Turns out it has been around for a while (since 3.15), so it
is good to finally get it resolved.
It has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbSgioACgkQMUfUDdst+ynUggCfdkzcX15M2vIiZsA3BLDcPY6L
pPcAnj1uCrqUUNRF3XgglbGXtp15sOe0
=R3bx
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/android fix from Greg KH:
"Here is one patch, for the android binder driver, to resolve a
reported problem. Turns out it has been around for a while (since
3.15), so it is good to finally get it resolved.
It has been in linux-next for a while with no reported issues"
* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
Here are a few USB fixes for 4.5-rc6
They fix a reported bug for some USB 3 devices by reverting the recent
patch, a MAINTAINERS change for some drivers, some new device ids, and
of course, the usual bunch of USB gadget driver fixes.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbSgVoACgkQMUfUDdst+ymghQCgiVUpZOu/hYeC/8CDdTZPLlpQ
oR4AoLftFf9OAKRgBCbiPOY99lG9f33y
=qZKR
-----END PGP SIGNATURE-----
Merge tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a few USB fixes for 4.5-rc6
They fix a reported bug for some USB 3 devices by reverting the recent
patch, a MAINTAINERS change for some drivers, some new device ids, and
of course, the usual bunch of USB gadget driver fixes.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: drop OMAP USB and MUSB maintainership
usb: musb: fix DMA for host mode
usb: phy: msm: Trigger USB state detection work in DRD mode
usb: gadget: net2280: fix endpoint max packet for super speed connections
usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
usb: gadget: remove driver from pending list on probe error
Revert "usb: hub: do not clear BOS field during reset device"
usb: chipidea: fix return value check in ci_hdrc_pci_probe()
usb: chipidea: error on overflow for port_test_write
USB: option: add "4G LTE usb-modem U901"
USB: cp210x: add IDs for GE B650V3 and B850V3 boards
USB: option: add support for SIM7100E
usb: musb: Fix DMA desired mode for Mentor DMA engine
usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
usb: dwc2: USB_DWC2 should depend on HAS_DMA
usb: dwc2: host: fix the data toggle error in full speed descriptor dma
usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
usb: dwc3: Fix assignment of EP transfer resources
usb: dwc2: Add extra delay when forcing dr_mode
Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.
Fix up vfio to do
return copy_to_user(...)) ?
-EFAULT : 0;
everywhere.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Bool initializations should use true and false. Bool tests don't need
comparisons.
Also, use IS_ENABLED instead of ifdef.
Generated by: scripts/coccinelle/misc/boolinit.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unneeded variables when "0" can be returned.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move constants to the right of binary operators where it increases
readability.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: drop some chunks and fix others, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
This commit drops implementation of duplex streams synchronization
from ALSA dice driver, due to a reason of hardware design. This patch
allows dice-based units to generate sounds correctly when isochronous
packet streaming starts at first time.
In IEC 61883-6:2005, CIP packetization layer for AM824 data format
utilizes the value of SYT field in CIP header of received packet for
a reference to phase lock loop. Figure 3 in clause 4.3 describes it.
The value is an offset from cycle_time field of every cycle start packet
from cycle master on IEEE 1394 bus. The time calculated with these two
fields is called as 'presentation timestamp' which represents the time
to play data included in the packet.
Although, this idea includes some problems due to accuracy of timekeep in
cycle master, accuracy of transmission of cycle start packet on the bus
with the other units, accuracy of sampling clock in data transmitter side
and accuracy of replay in data receiver side. In most case, these
accuracies somewhat worse because there's no such ideal hardwares in this
world.
For the issues, ASICs for Dice include Jitter Elimination Technologies
(JET) PLL. The PLL can handle several sources of clock and compensate it
with high-precision internal clock source. The sequence of value in syt
field of received AMDTP packets is one of the sources, therefore
transmitters on IEEE 1394 bus should transfer it.
On the other hand, current ALSA dice driver is programmed with a mode of
duplex streams with synchronization. In this mode, the driver outputs
packets after some incoming packets are handled, to re-use the value of
SYT field in incoming packets to the value for outgoing packets. This mode
is enabled when source signal of sampling clock is set to internal, and
this is a major use case. Thus, in most cases, the unit receives no packets
during a short time after packet streaming starts.
As long as I experienced, this causes the units to generate no sounds at
first time to receive packets. This issue occurs only with Dice II. I guess
this is due to a quirk of the PLL. In short, the PLL cannot generate firm
signals to ADCs/DACs or the other ICs when no packets are received in the
beginning of packet streaming. While, on second time or later, the unit
generates sound correctly. I guess that starting packet streaming at first
time sets the PLL correctly.
Well, still based on my hypothesis and no way to prove it, this commit
drops duplex streams synchronization from this driver. At least, the PLL
requires the sequence of value in SYT field of received AMDTP packets as
one of source of clock signals with internal clock source.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All the generic L2 cache handling code is encapsulated by a
check if the L2 cache is enabled. If it's enabled already, the code
is skipped. The write to the L2-Cache controller from non-secure
world causes an imprecise external abort. This is needed in
scenarios where one of the cores runs an other OS, e.g. an RTOS.
For the i.MX6 specific L2 cache handling we missed this check.
Add it.
Signed-off-by: Marcel Grosshans <MarcelViktor.Grosshans@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX only needs to select ARM_CPU_SUSPEND manually for the
very specific case that CONFIG_PM_SLEEP is disabled and imx6
is used with CONFIG_PM enabled for runtime PM.
If we are building a kernel only for CPUs that are not using
the cpu_suspend() helper, we otherwise get a harmless
build warning:
warning: (ARCH_MXC && SOC_IMX23 && SOC_IMX28 && ARCH_PXA && MACH_MVEBU_V7 && ARCH_OMAP3 && ARCH_OMAP4 && SOC_OMAP5 && SOC_AM33XX && SOC_DRA7XX && ARCH_EXYNOS3 && ARCH_EXYNOS4 && EXYNOS5420_MCPM &&
EXYNOS_CPU_SUSPEND && ARCH_VEXPRESS_TC2_PM && ARM_BIG_LITTLE_CPUIDLE && ARM_HIGHBANK_CPUIDLE && QCOM_PM) selects ARM_CPU_SUSPEND which has unmet direct dependencies (ARCH_SUSPEND_POSSIBLE)
This moves the option to the SOC_IMX6 option that actually
requires it, in effect reverting commit f36b594f37 ("ARM:
mach-imx: Select ARM_CPU_SUSPEND at ARCH_MXC level") that was
meant as a cleanup and unintentionally caused this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the necessary clock to use the KPP interface on i.MX6UL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull vfs fixes from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
do_last(): ELOOP failure exit should be done after leaving RCU mode
should_follow_link(): validate ->d_seq after having decided to follow
namei: ->d_inode of a pinned dentry is stable only for positives
do_last(): don't let a bogus return value from ->open() et.al. to confuse us
fs: return -EOPNOTSUPP if clone is not supported
hpfs: don't truncate the file when delete fails
We didn't have a batch last week, so this one is slightly larger.
None of them are scary though, a handful of fixes for small DT pieces,
replacing properties with newer conventions.
Highlights:
- N900 fix for setting system revision
- onenand init fix to avoid filesystem corruption
- Clock fix for audio on Beaglebone-x15
- Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)
+ misc smaller stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xeuW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have a batch last week, so this one is slightly larger.
None of them are scary though, a handful of fixes for small DT pieces,
replacing properties with newer conventions.
Highlights:
- N900 fix for setting system revision
- onenand init fix to avoid filesystem corruption
- Clock fix for audio on Beaglebone-x15
- Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)
+ misc smaller stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Extend info, add wiki and ml for meson arch
MAINTAINERS: alpine: add a new maintainer and update the entry
ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
ARM: shmobile: Remove shmobile_boot_arg
ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
ARM: shmobile: Move shmobile_scu_base from .text to .bss
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
... otherwise d_is_symlink() above might have nothing to do with
the inode value we've got.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
